bnx2x: Add Nic partitioning mode (57712 devices)

NIC partitioning is another flavor of multi function - having few
PCI functions share the same physical port. Unlike the currently
supported mode of multi-function which depends on the switch
configuration and uses outer-VLAN, the NPAR mode is switch independent
and uses the MAC addresses to distribute incoming packets to the different
functions. This patch adds the specific HW setting of the NPAR mode
and some distinctions between switch dependent (SD) and
switch independent (SI) multi-function (MF) modes where the configuration
is not the same.

Advance driver version to 1.60.00-6

Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1 files changed, 45 insertions, 13 deletions

diff --git a/drivers/net/bnx2x/bnx2x_ethtool.c b/drivers/net/bnx2x/bnx2x_ethtool.c
index 0301278..bd94827 100644
--- a/drivers/net/bnx2x/bnx2x_ethtool.c
+++ b/drivers/net/bnx2x/bnx2x_ethtool.c
@@ -45,14 +45,9 @@ static int bnx2x_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 		cmd->speed = bp->link_params.req_line_speed[cfg_idx];
 		cmd->duplex = bp->link_params.req_duplex[cfg_idx];
 	}
-	if (IS_MF(bp)) {
-		u16 vn_max_rate = ((bp->mf_config[BP_VN(bp)] &
-			FUNC_MF_CFG_MAX_BW_MASK) >> FUNC_MF_CFG_MAX_BW_SHIFT) *
-			100;
 
-		if (vn_max_rate < cmd->speed)
-			cmd->speed = vn_max_rate;
-	}
+	if (IS_MF(bp))
+		cmd->speed = bnx2x_get_mf_speed(bp);
 
 	if (bp->port.supported[cfg_idx] & SUPPORTED_TP)
 		cmd->port = PORT_TP;
@@ -87,18 +82,57 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
 	struct bnx2x *bp = netdev_priv(dev);
 	u32 advertising, cfg_idx, old_multi_phy_config, new_multi_phy_config;
+	u32 speed;
 
-	if (IS_MF(bp))
+	if (IS_MF_SD(bp))
 		return 0;
 
 	DP(NETIF_MSG_LINK, "ethtool_cmd: cmd %d\n"
-	   DP_LEVEL "  supported 0x%x  advertising 0x%x  speed %d\n"
-	   DP_LEVEL "  duplex %d  port %d  phy_address %d  transceiver %d\n"
-	   DP_LEVEL "  autoneg %d  maxtxpkt %d  maxrxpkt %d\n",
+	   "  supported 0x%x  advertising 0x%x  speed %d speed_hi %d\n"
+	   "  duplex %d  port %d  phy_address %d  transceiver %d\n"
+	   "  autoneg %d  maxtxpkt %d  maxrxpkt %d\n",
 	   cmd->cmd, cmd->supported, cmd->advertising, cmd->speed,
+	   cmd->speed_hi,
 	   cmd->duplex, cmd->port, cmd->phy_address, cmd->transceiver,
 	   cmd->autoneg, cmd->maxtxpkt, cmd->maxrxpkt);
 
+	speed = cmd->speed;
+	speed |= (cmd->speed_hi << 16);
+
+	if (IS_MF_SI(bp)) {
+		u32 param = 0;
+		u32 line_speed = bp->link_vars.line_speed;
+
+		/* use 10G if no link detected */
+		if (!line_speed)
+			line_speed = 10000;
+
+		if (bp->common.bc_ver < REQ_BC_VER_4_SET_MF_BW) {
+			BNX2X_DEV_INFO("To set speed BC %X or higher "
+				       "is required, please upgrade BC\n",
+				       REQ_BC_VER_4_SET_MF_BW);
+			return -EINVAL;
+		}
+		if (line_speed < speed) {
+			BNX2X_DEV_INFO("New speed should be less or equal "
+				       "to actual line speed\n");
+			return -EINVAL;
+		}
+		/* load old values */
+		param = bp->mf_config[BP_VN(bp)];
+
+		/* leave only MIN value */
+		param &= FUNC_MF_CFG_MIN_BW_MASK;
+
+		/* set new MAX value */
+		param |= (((speed * 100) / line_speed)
+				 << FUNC_MF_CFG_MAX_BW_SHIFT)
+				  & FUNC_MF_CFG_MAX_BW_MASK;
+
+		bnx2x_fw_command(bp, DRV_MSG_CODE_SET_MF_BW, param);
+		return 0;
+	}
+
 	cfg_idx = bnx2x_get_link_cfg_idx(bp);
 	old_multi_phy_config = bp->link_params.multi_phy_config;
 	switch (cmd->port) {
@@ -168,8 +202,6 @@ static int bnx2x_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 
 	} else { /* forced speed */
 		/* advertise the requested speed and duplex if supported */
-		u32 speed = cmd->speed;
-		speed |= (cmd->speed_hi << 16);
 		switch (speed) {
 		case SPEED_10:
 			if (cmd->duplex == DUPLEX_FULL) {