Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 91 insertions, 0 deletions

diff --git a/drivers/net/3c503.h b/drivers/net/3c503.h
new file mode 100644
index 0000000..b9f8a46
--- /dev/null
+++ b/drivers/net/3c503.h
@@ -0,0 +1,91 @@
+/* Definitions for the 3Com 3c503 Etherlink 2. */
+/* This file is distributed under the GPL.
+   Many of these names and comments are directly from the Crynwr packet
+   drivers, which are released under the GPL. */
+
+#define EL2H (dev->base_addr + 0x400)
+#define EL2L (dev->base_addr)
+
+/* Vendor unique hardware addr. prefix. 3Com has 2 because they ran
+   out of available addresses on the first one... */
+
+#define OLD_3COM_ID	0x02608c
+#define NEW_3COM_ID	0x0020af
+
+/* Shared memory management parameters. NB: The 8 bit cards have only
+   one bank (MB1) which serves both Tx and Rx packet space. The 16bit
+   cards have 2 banks, MB0 for Tx packets, and MB1 for Rx packets. 
+   You choose which bank appears in the sh. mem window with EGACFR_MBSn */
+
+#define EL2_MB0_START_PG	(0x00)	/* EL2/16 Tx packets go in bank 0 */
+#define EL2_MB1_START_PG	(0x20)	/* First page of bank 1 */
+#define EL2_MB1_STOP_PG		(0x40)	/* Last page +1 of bank 1 */
+
+/* 3Com 3c503 ASIC registers */
+#define E33G_STARTPG	(EL2H+0)	/* Start page, matching EN0_STARTPG */
+#define E33G_STOPPG	(EL2H+1)	/* Stop page, must match EN0_STOPPG */
+#define E33G_DRQCNT	(EL2H+2)	/* DMA burst count */
+#define E33G_IOBASE	(EL2H+3)	/* Read of I/O base jumpers. */
+	/* (non-useful, but it also appears at the end of EPROM space) */
+#define E33G_ROMBASE	(EL2H+4)	/* Read of memory base jumpers. */
+#define E33G_GACFR	(EL2H+5)	/* Config/setup bits for the ASIC GA */
+#define E33G_CNTRL	(EL2H+6)	/* Board's main control register */
+#define E33G_STATUS	(EL2H+7)	/* Status on completions. */
+#define E33G_IDCFR	(EL2H+8)	/* Interrupt/DMA config register */
+				/* (Which IRQ to assert, DMA chan to use) */
+#define E33G_DMAAH	(EL2H+9)	/* High byte of DMA address reg */
+#define E33G_DMAAL	(EL2H+10)	/* Low byte of DMA address reg */
+/* "Vector pointer" - if this address matches a read, the EPROM (rather than
+   shared RAM) is mapped into memory space. */
+#define E33G_VP2	(EL2H+11)
+#define E33G_VP1	(EL2H+12)
+#define E33G_VP0	(EL2H+13)
+#define E33G_FIFOH	(EL2H+14)	/* FIFO for programmed I/O moves */
+#define E33G_FIFOL	(EL2H+15)	/* ... low byte of above. */
+
+/* Bits in E33G_CNTRL register: */
+
+#define ECNTRL_RESET	(0x01)	/* Software reset of the ASIC and 8390 */
+#define ECNTRL_THIN	(0x02)	/* Onboard xcvr enable, AUI disable */
+#define ECNTRL_AUI	(0x00)	/* Onboard xcvr disable, AUI enable */
+#define ECNTRL_SAPROM	(0x04)	/* Map the station address prom */
+#define ECNTRL_DBLBFR	(0x20)	/* FIFO configuration bit */
+#define ECNTRL_OUTPUT	(0x40)	/* PC-to-3C503 direction if 1 */
+#define ECNTRL_INPUT	(0x00)	/* 3C503-to-PC direction if 0 */
+#define ECNTRL_START	(0x80)	/* Start the DMA logic */
+
+/* Bits in E33G_STATUS register: */
+
+#define ESTAT_DPRDY	(0x80)	/* Data port (of FIFO) ready */
+#define ESTAT_UFLW	(0x40)	/* Tried to read FIFO when it was empty */
+#define ESTAT_OFLW	(0x20)	/* Tried to write FIFO when it was full */
+#define ESTAT_DTC	(0x10)	/* Terminal Count from PC bus DMA logic */
+#define ESTAT_DIP	(0x08)	/* DMA In Progress */
+
+/* Bits in E33G_GACFR register: */
+
+#define EGACFR_NIM	(0x80)	/* NIC interrupt mask */
+#define EGACFR_TCM	(0x40)	/* DMA term. count interrupt mask */
+#define EGACFR_RSEL	(0x08)	/* Map a bank of card mem into system mem */
+#define EGACFR_MBS2	(0x04)	/* Memory bank select, bit 2. */
+#define EGACFR_MBS1	(0x02)	/* Memory bank select, bit 1. */
+#define EGACFR_MBS0	(0x01)	/* Memory bank select, bit 0. */
+
+#define EGACFR_NORM	(0x49)	/* TCM | RSEL | MBS0 */
+#define EGACFR_IRQOFF	(0xc9)	/* TCM | RSEL | MBS0 | NIM */
+
+/*
+	MBS2	MBS1	MBS0	Sh. mem windows card mem at:
+	----	----	----	-----------------------------
+	0	0	0	0x0000 -- bank 0
+	0	0	1	0x2000 -- bank 1 (only choice for 8bit card)
+	0	1	0	0x4000 -- bank 2, not used
+	0	1	1	0x6000 -- bank 3, not used
+
+There was going to be a 32k card that used bank 2 and 3, but it 
+never got produced.
+
+*/
+
+
+/* End of 3C503 parameter definitions */