mmc: sdhci-esdhc-imx: add imx7d support and support HS400

The imx7d usdhc is derived from imx6sx, the difference is that
imx7d support HS400.

So introduce a new compatible string for imx7d and add HS400
support for imx7d usdhc.

Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

1 files changed, 83 insertions, 3 deletions

diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index c6b9f64..b8b7e88 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -44,6 +44,7 @@
 #define  ESDHC_MIX_CTRL_EXE_TUNE	(1 << 22)
 #define  ESDHC_MIX_CTRL_SMPCLK_SEL	(1 << 23)
 #define  ESDHC_MIX_CTRL_FBCLK_SEL	(1 << 25)
+#define  ESDHC_MIX_CTRL_HS400_EN	(1 << 26)
 /* Bits 3 and 6 are not SDHCI standard definitions */
 #define  ESDHC_MIX_CTRL_SDHCI_MASK	0xb7
 /* Tuning bits */
@@ -60,6 +61,16 @@
 #define  ESDHC_TUNE_CTRL_MIN		0
 #define  ESDHC_TUNE_CTRL_MAX		((1 << 7) - 1)
 
+/* strobe dll register */
+#define ESDHC_STROBE_DLL_CTRL		0x70
+#define ESDHC_STROBE_DLL_CTRL_ENABLE	(1 << 0)
+#define ESDHC_STROBE_DLL_CTRL_RESET	(1 << 1)
+#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT	3
+
+#define ESDHC_STROBE_DLL_STATUS		0x74
+#define ESDHC_STROBE_DLL_STS_REF_LOCK	(1 << 1)
+#define ESDHC_STROBE_DLL_STS_SLV_LOCK	0x1
+
 #define ESDHC_TUNING_CTRL		0xcc
 #define ESDHC_STD_TUNING_EN		(1 << 24)
 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
@@ -120,6 +131,11 @@
 #define ESDHC_FLAG_ERR004536		BIT(7)
 /* The IP supports HS200 mode */
 #define ESDHC_FLAG_HS200		BIT(8)
+/* The IP supports HS400 mode */
+#define ESDHC_FLAG_HS400		BIT(9)
+
+/* A higher clock ferquency than this rate requires strobell dll control */
+#define ESDHC_STROBE_DLL_CLK_FREQ	100000000
 
 struct esdhc_soc_data {
 	u32 flags;
@@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = {
 			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
 };
 
+static struct esdhc_soc_data usdhc_imx7d_data = {
+	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
+			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
+			| ESDHC_FLAG_HS400,
+};
+
 struct pltfm_imx_data {
 	u32 scratchpad;
 	struct pinctrl *pinctrl;
@@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[] = {
 	{ .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
 	{ .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
 	{ .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
+	{ .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
@@ -274,6 +297,9 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
 				val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
 					| SDHCI_SUPPORT_SDR50
 					| SDHCI_USE_SDR50_TUNING;
+
+			if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+				val |= SDHCI_SUPPORT_HS400;
 		}
 	}
 
@@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
 		break;
 	case MMC_TIMING_UHS_SDR104:
 	case MMC_TIMING_MMC_HS200:
+	case MMC_TIMING_MMC_HS400:
 		pinctrl = imx_data->pins_200mhz;
 		break;
 	default:
@@ -784,24 +811,68 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
 	return pinctrl_select_state(imx_data->pinctrl, pinctrl);
 }
 
+/*
+ * For HS400 eMMC, there is a data_strobe line, this signal is generated
+ * by the device and used for data output and CRC status response output
+ * in HS400 mode. The frequency of this signal follows the frequency of
+ * CLK generated by host. Host receive the data which is aligned to the
+ * edge of data_strobe line. Due to the time delay between CLK line and
+ * data_strobe line, if the delay time is larger than one clock cycle,
+ * then CLK and data_strobe line will misaligned, read error shows up.
+ * So when the CLK is higher than 100MHz, each clock cycle is short enough,
+ * host should config the delay target.
+ */
+static void esdhc_set_strobe_dll(struct sdhci_host *host)
+{
+	u32 v;
+
+	if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) {
+		/* force a reset on strobe dll */
+		writel(ESDHC_STROBE_DLL_CTRL_RESET,
+			host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+		/*
+		 * enable strobe dll ctrl and adjust the delay target
+		 * for the uSDHC loopback read clock
+		 */
+		v = ESDHC_STROBE_DLL_CTRL_ENABLE |
+			(7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
+		writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
+		/* wait 1us to make sure strobe dll status register stable */
+		udelay(1);
+		v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
+		if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
+			dev_warn(mmc_dev(host->mmc),
+				"warning! HS400 strobe DLL status REF not lock!\n");
+		if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
+			dev_warn(mmc_dev(host->mmc),
+				"warning! HS400 strobe DLL status SLV not lock!\n");
+	}
+}
+
 static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 {
+	u32 m;
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct pltfm_imx_data *imx_data = pltfm_host->priv;
 	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
 
+	/* disable ddr mode and disable HS400 mode */
+	m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+	m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
+	imx_data->is_ddr = 0;
+
 	switch (timing) {
 	case MMC_TIMING_UHS_SDR12:
 	case MMC_TIMING_UHS_SDR25:
 	case MMC_TIMING_UHS_SDR50:
 	case MMC_TIMING_UHS_SDR104:
 	case MMC_TIMING_MMC_HS200:
+		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 		break;
 	case MMC_TIMING_UHS_DDR50:
 	case MMC_TIMING_MMC_DDR52:
-		writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
-				ESDHC_MIX_CTRL_DDREN,
-				host->ioaddr + ESDHC_MIX_CTRL);
+		m |= ESDHC_MIX_CTRL_DDREN;
+		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
 		imx_data->is_ddr = 1;
 		if (boarddata->delay_line) {
 			u32 v;
@@ -813,6 +884,12 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
 			writel(v, host->ioaddr + ESDHC_DLL_CTRL);
 		}
 		break;
+	case MMC_TIMING_MMC_HS400:
+		m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
+		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
+		imx_data->is_ddr = 1;
+		esdhc_set_strobe_dll(host);
+		break;
 	}
 
 	esdhc_change_pinstate(host, timing);
@@ -1100,6 +1177,9 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
 	if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
 		host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
 
+	if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
+		host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
+
 	if (of_id)
 		err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
 	else