mmc: sdhci: Remove the sdhci exported header file

Since there no users of the struct sdhci_host, but the shdci host
drivers themselves, let's move the definition of it to the local sdhci
header.

The exported sdhci header then becomes empty, so let's remove it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

2 files changed, 202 insertions, 2 deletions

diff --git a/drivers/mmc/host/sdhci-acpi.c b/drivers/mmc/host/sdhci-acpi.c
index a45ed39..22d929f 100644
--- a/drivers/mmc/host/sdhci-acpi.c
+++ b/drivers/mmc/host/sdhci-acpi.c
@@ -40,7 +40,6 @@
 #include <linux/mmc/host.h>
 #include <linux/mmc/pm.h>
 #include <linux/mmc/slot-gpio.h>
-#include <linux/mmc/sdhci.h>
 
 #include "sdhci.h"
 
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index 0315e18..e639b7f 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -18,7 +18,7 @@
 #include <linux/types.h>
 #include <linux/io.h>
 
-#include <linux/mmc/sdhci.h>
+#include <linux/mmc/host.h>
 
 /*
  * Controller registers
@@ -309,6 +309,207 @@ struct sdhci_adma2_64_desc {
  */
 #define SDHCI_MAX_SEGS		128
 
+struct sdhci_host_next {
+	unsigned int	sg_count;
+	s32		cookie;
+};
+
+struct sdhci_host {
+	/* Data set by hardware interface driver */
+	const char *hw_name;	/* Hardware bus name */
+
+	unsigned int quirks;	/* Deviations from spec. */
+
+/* Controller doesn't honor resets unless we touch the clock register */
+#define SDHCI_QUIRK_CLOCK_BEFORE_RESET			(1<<0)
+/* Controller has bad caps bits, but really supports DMA */
+#define SDHCI_QUIRK_FORCE_DMA				(1<<1)
+/* Controller doesn't like to be reset when there is no card inserted. */
+#define SDHCI_QUIRK_NO_CARD_NO_RESET			(1<<2)
+/* Controller doesn't like clearing the power reg before a change */
+#define SDHCI_QUIRK_SINGLE_POWER_WRITE			(1<<3)
+/* Controller has flaky internal state so reset it on each ios change */
+#define SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS		(1<<4)
+/* Controller has an unusable DMA engine */
+#define SDHCI_QUIRK_BROKEN_DMA				(1<<5)
+/* Controller has an unusable ADMA engine */
+#define SDHCI_QUIRK_BROKEN_ADMA				(1<<6)
+/* Controller can only DMA from 32-bit aligned addresses */
+#define SDHCI_QUIRK_32BIT_DMA_ADDR			(1<<7)
+/* Controller can only DMA chunk sizes that are a multiple of 32 bits */
+#define SDHCI_QUIRK_32BIT_DMA_SIZE			(1<<8)
+/* Controller can only ADMA chunks that are a multiple of 32 bits */
+#define SDHCI_QUIRK_32BIT_ADMA_SIZE			(1<<9)
+/* Controller needs to be reset after each request to stay stable */
+#define SDHCI_QUIRK_RESET_AFTER_REQUEST			(1<<10)
+/* Controller needs voltage and power writes to happen separately */
+#define SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER		(1<<11)
+/* Controller provides an incorrect timeout value for transfers */
+#define SDHCI_QUIRK_BROKEN_TIMEOUT_VAL			(1<<12)
+/* Controller has an issue with buffer bits for small transfers */
+#define SDHCI_QUIRK_BROKEN_SMALL_PIO			(1<<13)
+/* Controller does not provide transfer-complete interrupt when not busy */
+#define SDHCI_QUIRK_NO_BUSY_IRQ				(1<<14)
+/* Controller has unreliable card detection */
+#define SDHCI_QUIRK_BROKEN_CARD_DETECTION		(1<<15)
+/* Controller reports inverted write-protect state */
+#define SDHCI_QUIRK_INVERTED_WRITE_PROTECT		(1<<16)
+/* Controller does not like fast PIO transfers */
+#define SDHCI_QUIRK_PIO_NEEDS_DELAY			(1<<18)
+/* Controller has to be forced to use block size of 2048 bytes */
+#define SDHCI_QUIRK_FORCE_BLK_SZ_2048			(1<<20)
+/* Controller cannot do multi-block transfers */
+#define SDHCI_QUIRK_NO_MULTIBLOCK			(1<<21)
+/* Controller can only handle 1-bit data transfers */
+#define SDHCI_QUIRK_FORCE_1_BIT_DATA			(1<<22)
+/* Controller needs 10ms delay between applying power and clock */
+#define SDHCI_QUIRK_DELAY_AFTER_POWER			(1<<23)
+/* Controller uses SDCLK instead of TMCLK for data timeouts */
+#define SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK		(1<<24)
+/* Controller reports wrong base clock capability */
+#define SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN		(1<<25)
+/* Controller cannot support End Attribute in NOP ADMA descriptor */
+#define SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC		(1<<26)
+/* Controller is missing device caps. Use caps provided by host */
+#define SDHCI_QUIRK_MISSING_CAPS			(1<<27)
+/* Controller uses Auto CMD12 command to stop the transfer */
+#define SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12		(1<<28)
+/* Controller doesn't have HISPD bit field in HI-SPEED SD card */
+#define SDHCI_QUIRK_NO_HISPD_BIT			(1<<29)
+/* Controller treats ADMA descriptors with length 0000h incorrectly */
+#define SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC		(1<<30)
+/* The read-only detection via SDHCI_PRESENT_STATE register is unstable */
+#define SDHCI_QUIRK_UNSTABLE_RO_DETECT			(1<<31)
+
+	unsigned int quirks2;	/* More deviations from spec. */
+
+#define SDHCI_QUIRK2_HOST_OFF_CARD_ON			(1<<0)
+#define SDHCI_QUIRK2_HOST_NO_CMD23			(1<<1)
+/* The system physically doesn't support 1.8v, even if the host does */
+#define SDHCI_QUIRK2_NO_1_8_V				(1<<2)
+#define SDHCI_QUIRK2_PRESET_VALUE_BROKEN		(1<<3)
+#define SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON		(1<<4)
+/* Controller has a non-standard host control register */
+#define SDHCI_QUIRK2_BROKEN_HOST_CONTROL		(1<<5)
+/* Controller does not support HS200 */
+#define SDHCI_QUIRK2_BROKEN_HS200			(1<<6)
+/* Controller does not support DDR50 */
+#define SDHCI_QUIRK2_BROKEN_DDR50			(1<<7)
+/* Stop command (CMD12) can set Transfer Complete when not using MMC_RSP_BUSY */
+#define SDHCI_QUIRK2_STOP_WITH_TC			(1<<8)
+/* Controller does not support 64-bit DMA */
+#define SDHCI_QUIRK2_BROKEN_64_BIT_DMA			(1<<9)
+/* need clear transfer mode register before send cmd */
+#define SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD	(1<<10)
+/* Capability register bit-63 indicates HS400 support */
+#define SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400		(1<<11)
+/* forced tuned clock */
+#define SDHCI_QUIRK2_TUNING_WORK_AROUND			(1<<12)
+/* disable the block count for single block transactions */
+#define SDHCI_QUIRK2_SUPPORT_SINGLE			(1<<13)
+/* Controller broken with using ACMD23 */
+#define SDHCI_QUIRK2_ACMD23_BROKEN			(1<<14)
+
+	int irq;		/* Device IRQ */
+	void __iomem *ioaddr;	/* Mapped address */
+
+	const struct sdhci_ops *ops;	/* Low level hw interface */
+
+	/* Internal data */
+	struct mmc_host *mmc;	/* MMC structure */
+	u64 dma_mask;		/* custom DMA mask */
+
+#if defined(CONFIG_LEDS_CLASS) || defined(CONFIG_LEDS_CLASS_MODULE)
+	struct led_classdev led;	/* LED control */
+	char led_name[32];
+#endif
+
+	spinlock_t lock;	/* Mutex */
+
+	int flags;		/* Host attributes */
+#define SDHCI_USE_SDMA		(1<<0)	/* Host is SDMA capable */
+#define SDHCI_USE_ADMA		(1<<1)	/* Host is ADMA capable */
+#define SDHCI_REQ_USE_DMA	(1<<2)	/* Use DMA for this req. */
+#define SDHCI_DEVICE_DEAD	(1<<3)	/* Device unresponsive */
+#define SDHCI_SDR50_NEEDS_TUNING (1<<4)	/* SDR50 needs tuning */
+#define SDHCI_NEEDS_RETUNING	(1<<5)	/* Host needs retuning */
+#define SDHCI_AUTO_CMD12	(1<<6)	/* Auto CMD12 support */
+#define SDHCI_AUTO_CMD23	(1<<7)	/* Auto CMD23 support */
+#define SDHCI_PV_ENABLED	(1<<8)	/* Preset value enabled */
+#define SDHCI_SDIO_IRQ_ENABLED	(1<<9)	/* SDIO irq enabled */
+#define SDHCI_SDR104_NEEDS_TUNING (1<<10)	/* SDR104/HS200 needs tuning */
+#define SDHCI_USING_RETUNING_TIMER (1<<11)	/* Host is using a retuning timer for the card */
+#define SDHCI_USE_64_BIT_DMA	(1<<12)	/* Use 64-bit DMA */
+#define SDHCI_HS400_TUNING	(1<<13)	/* Tuning for HS400 */
+
+	unsigned int version;	/* SDHCI spec. version */
+
+	unsigned int max_clk;	/* Max possible freq (MHz) */
+	unsigned int timeout_clk;	/* Timeout freq (KHz) */
+	unsigned int clk_mul;	/* Clock Muliplier value */
+
+	unsigned int clock;	/* Current clock (MHz) */
+	u8 pwr;			/* Current voltage */
+
+	bool runtime_suspended;	/* Host is runtime suspended */
+	bool bus_on;		/* Bus power prevents runtime suspend */
+	bool preset_enabled;	/* Preset is enabled */
+
+	struct mmc_request *mrq;	/* Current request */
+	struct mmc_command *cmd;	/* Current command */
+	struct mmc_data *data;	/* Current data request */
+	unsigned int data_early:1;	/* Data finished before cmd */
+	unsigned int busy_handle:1;	/* Handling the order of Busy-end */
+
+	struct sg_mapping_iter sg_miter;	/* SG state for PIO */
+	unsigned int blocks;	/* remaining PIO blocks */
+
+	int sg_count;		/* Mapped sg entries */
+
+	void *adma_table;	/* ADMA descriptor table */
+	void *align_buffer;	/* Bounce buffer */
+
+	size_t adma_table_sz;	/* ADMA descriptor table size */
+	size_t align_buffer_sz;	/* Bounce buffer size */
+
+	dma_addr_t adma_addr;	/* Mapped ADMA descr. table */
+	dma_addr_t align_addr;	/* Mapped bounce buffer */
+
+	unsigned int desc_sz;	/* ADMA descriptor size */
+	unsigned int align_sz;	/* ADMA alignment */
+	unsigned int align_mask;	/* ADMA alignment mask */
+
+	struct tasklet_struct finish_tasklet;	/* Tasklet structures */
+
+	struct timer_list timer;	/* Timer for timeouts */
+
+	u32 caps;		/* Alternative CAPABILITY_0 */
+	u32 caps1;		/* Alternative CAPABILITY_1 */
+
+	unsigned int            ocr_avail_sdio;	/* OCR bit masks */
+	unsigned int            ocr_avail_sd;
+	unsigned int            ocr_avail_mmc;
+	u32 ocr_mask;		/* available voltages */
+
+	unsigned		timing;		/* Current timing */
+
+	u32			thread_isr;
+
+	/* cached registers */
+	u32			ier;
+
+	wait_queue_head_t	buf_ready_int;	/* Waitqueue for Buffer Read Ready interrupt */
+	unsigned int		tuning_done;	/* Condition flag set when CMD19 succeeds */
+
+	unsigned int		tuning_count;	/* Timer count for re-tuning */
+	unsigned int		tuning_mode;	/* Re-tuning mode supported by host */
+#define SDHCI_TUNING_MODE_1	0
+	struct timer_list	tuning_timer;	/* Timer for tuning */
+
+	struct sdhci_host_next	next_data;
+	unsigned long private[0] ____cacheline_aligned;
+};
+
 struct sdhci_ops {
 #ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
 	u32		(*read_l)(struct sdhci_host *host, int reg);