mmc: rework selection of bus speed mode

Current implementation for bus speed mode selection is too
complicated. This patch is to simplify the codes and remove
some duplicate parts.

The following changes are including:
* Adds functions for each mode selection(HS, HS-DDR, HS200 and etc)
* Rearranged the mode selection sequence with supported device type
* Adds maximum speed for HS200 mode(hs200_max_dtr)
* Adds field definition for HS_TIMING of EXT_CSD

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>

2 files changed, 233 insertions, 200 deletions

diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c
index 509229b..1f730db 100644
--- a/drivers/mmc/core/debugfs.c
+++ b/drivers/mmc/core/debugfs.c
@@ -139,7 +139,7 @@ static int mmc_ios_show(struct seq_file *s, void *data)
 		str = "mmc DDR52";
 		break;
 	case MMC_TIMING_MMC_HS200:
-		str = "mmc high-speed SDR200";
+		str = "mmc HS200";
 		break;
 	default:
 		str = "invalid";
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index 4538541..bec6786 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -242,7 +242,7 @@ static void mmc_select_card_type(struct mmc_card *card)
 	struct mmc_host *host = card->host;
 	u8 card_type = card->ext_csd.raw_card_type & EXT_CSD_CARD_TYPE_MASK;
 	u32 caps = host->caps, caps2 = host->caps2;
-	unsigned int hs_max_dtr = 0;
+	unsigned int hs_max_dtr = 0, hs200_max_dtr = 0;
 	unsigned int avail_type = 0;
 
 	if (caps & MMC_CAP_MMC_HIGHSPEED &&
@@ -271,17 +271,18 @@ static void mmc_select_card_type(struct mmc_card *card)
 
 	if (caps2 & MMC_CAP2_HS200_1_8V_SDR &&
 	    card_type & EXT_CSD_CARD_TYPE_HS200_1_8V) {
-		hs_max_dtr = MMC_HS200_MAX_DTR;
+		hs200_max_dtr = MMC_HS200_MAX_DTR;
 		avail_type |= EXT_CSD_CARD_TYPE_HS200_1_8V;
 	}
 
 	if (caps2 & MMC_CAP2_HS200_1_2V_SDR &&
 	    card_type & EXT_CSD_CARD_TYPE_HS200_1_2V) {
-		hs_max_dtr = MMC_HS200_MAX_DTR;
+		hs200_max_dtr = MMC_HS200_MAX_DTR;
 		avail_type |= EXT_CSD_CARD_TYPE_HS200_1_2V;
 	}
 
 	card->ext_csd.hs_max_dtr = hs_max_dtr;
+	card->ext_csd.hs200_max_dtr = hs200_max_dtr;
 	card->mmc_avail_type = avail_type;
 }
 
@@ -825,37 +826,46 @@ static int mmc_select_powerclass(struct mmc_card *card)
 }
 
 /*
- * Selects the desired buswidth and switch to the HS200 mode
- * if bus width set without error
+ * Set the bus speed for the selected speed mode.
  */
-static int mmc_select_hs200(struct mmc_card *card)
+static void mmc_set_bus_speed(struct mmc_card *card)
+{
+	unsigned int max_dtr = (unsigned int)-1;
+
+	if (mmc_card_hs200(card) && max_dtr > card->ext_csd.hs200_max_dtr)
+		max_dtr = card->ext_csd.hs200_max_dtr;
+	else if (mmc_card_hs(card) && max_dtr > card->ext_csd.hs_max_dtr)
+		max_dtr = card->ext_csd.hs_max_dtr;
+	else if (max_dtr > card->csd.max_dtr)
+		max_dtr = card->csd.max_dtr;
+
+	mmc_set_clock(card->host, max_dtr);
+}
+
+/*
+ * Select the bus width amoung 4-bit and 8-bit(SDR).
+ * If the bus width is changed successfully, return the selected width value.
+ * Zero is returned instead of error value if the wide width is not supported.
+ */
+static int mmc_select_bus_width(struct mmc_card *card)
 {
-	int idx, err = -EINVAL;
-	struct mmc_host *host;
 	static unsigned ext_csd_bits[] = {
-		EXT_CSD_BUS_WIDTH_4,
 		EXT_CSD_BUS_WIDTH_8,
+		EXT_CSD_BUS_WIDTH_4,
 	};
 	static unsigned bus_widths[] = {
-		MMC_BUS_WIDTH_4,
 		MMC_BUS_WIDTH_8,
+		MMC_BUS_WIDTH_4,
 	};
+	struct mmc_host *host = card->host;
+	unsigned idx, bus_width = 0;
+	int err = 0;
 
-	BUG_ON(!card);
-
-	host = card->host;
-
-	if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200_1_2V)
-		err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
-
-	if (err && card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200_1_8V)
-		err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
-
-	/* If fails try again during next card power cycle */
-	if (err)
-		goto err;
+	if ((card->csd.mmca_vsn < CSD_SPEC_VER_4) &&
+	    !(host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)))
+		return 0;
 
-	idx = (host->caps & MMC_CAP_8_BIT_DATA) ? 1 : 0;
+	idx = (host->caps & MMC_CAP_8_BIT_DATA) ? 0 : 1;
 
 	/*
 	 * Unlike SD, MMC cards dont have a configuration register to notify
@@ -863,8 +873,7 @@ static int mmc_select_hs200(struct mmc_card *card)
 	 * the supported bus width or compare the ext csd values of current
 	 * bus width and ext csd values of 1 bit mode read earlier.
 	 */
-	for (; idx >= 0; idx--) {
-
+	for (; idx < ARRAY_SIZE(bus_widths); idx++) {
 		/*
 		 * Host is capable of 8bit transfer, then switch
 		 * the device to work in 8bit transfer mode. If the
@@ -879,27 +888,202 @@ static int mmc_select_hs200(struct mmc_card *card)
 		if (err)
 			continue;
 
-		mmc_set_bus_width(card->host, bus_widths[idx]);
+		bus_width = bus_widths[idx];
+		mmc_set_bus_width(host, bus_width);
 
+		/*
+		 * If controller can't handle bus width test,
+		 * compare ext_csd previously read in 1 bit mode
+		 * against ext_csd at new bus width
+		 */
 		if (!(host->caps & MMC_CAP_BUS_WIDTH_TEST))
-			err = mmc_compare_ext_csds(card, bus_widths[idx]);
+			err = mmc_compare_ext_csds(card, bus_width);
 		else
-			err = mmc_bus_test(card, bus_widths[idx]);
-		if (!err)
+			err = mmc_bus_test(card, bus_width);
+
+		if (!err) {
+			err = bus_width;
 			break;
+		} else {
+			pr_warn("%s: switch to bus width %d failed\n",
+				mmc_hostname(host), ext_csd_bits[idx]);
+		}
 	}
 
-	/* switch to HS200 mode if bus width set successfully */
+	return err;
+}
+
+/*
+ * Switch to the high-speed mode
+ */
+static int mmc_select_hs(struct mmc_card *card)
+{
+	int err;
+
+	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+			   EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS,
+			   card->ext_csd.generic_cmd6_time,
+			   true, true, true);
 	if (!err)
+		mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
+
+	return err;
+}
+
+/*
+ * Activate wide bus and DDR if supported.
+ */
+static int mmc_select_hs_ddr(struct mmc_card *card)
+{
+	struct mmc_host *host = card->host;
+	u32 bus_width, ext_csd_bits;
+	int err = 0;
+
+	if (!(card->mmc_avail_type & EXT_CSD_CARD_TYPE_DDR_52))
+		return 0;
+
+	bus_width = host->ios.bus_width;
+	if (bus_width == MMC_BUS_WIDTH_1)
+		return 0;
+
+	ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
+		EXT_CSD_DDR_BUS_WIDTH_8 : EXT_CSD_DDR_BUS_WIDTH_4;
+
+	err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+			EXT_CSD_BUS_WIDTH,
+			ext_csd_bits,
+			card->ext_csd.generic_cmd6_time);
+	if (err) {
+		pr_warn("%s: switch to bus width %d ddr failed\n",
+			mmc_hostname(host), 1 << bus_width);
+		return err;
+	}
+
+	/*
+	 * eMMC cards can support 3.3V to 1.2V i/o (vccq)
+	 * signaling.
+	 *
+	 * EXT_CSD_CARD_TYPE_DDR_1_8V means 3.3V or 1.8V vccq.
+	 *
+	 * 1.8V vccq at 3.3V core voltage (vcc) is not required
+	 * in the JEDEC spec for DDR.
+	 *
+	 * Do not force change in vccq since we are obviously
+	 * working and no change to vccq is needed.
+	 *
+	 * WARNING: eMMC rules are NOT the same as SD DDR
+	 */
+	if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_DDR_1_2V) {
+		err = __mmc_set_signal_voltage(host,
+				MMC_SIGNAL_VOLTAGE_120);
+		if (err)
+			return err;
+	}
+
+	mmc_set_timing(host, MMC_TIMING_MMC_DDR52);
+
+	return err;
+}
+
+/*
+ * For device supporting HS200 mode, the following sequence
+ * should be done before executing the tuning process.
+ * 1. set the desired bus width(4-bit or 8-bit, 1-bit is not supported)
+ * 2. switch to HS200 mode
+ * 3. set the clock to > 52Mhz and <=200MHz
+ */
+static int mmc_select_hs200(struct mmc_card *card)
+{
+	struct mmc_host *host = card->host;
+	int err = -EINVAL;
+
+	if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200_1_2V)
+		err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_120);
+
+	if (err && card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200_1_8V)
+		err = __mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_180);
+
+	/* If fails try again during next card power cycle */
+	if (err)
+		goto err;
+
+	/*
+	 * Set the bus width(4 or 8) with host's support and
+	 * switch to HS200 mode if bus width is set successfully.
+	 */
+	err = mmc_select_bus_width(card);
+	if (!IS_ERR_VALUE(err)) {
 		err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
-				EXT_CSD_HS_TIMING, 2,
-				card->ext_csd.generic_cmd6_time,
-				true, true, true);
+				   EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS200,
+				   card->ext_csd.generic_cmd6_time,
+				   true, true, true);
+		if (!err)
+			mmc_set_timing(host, MMC_TIMING_MMC_HS200);
+	}
 err:
 	return err;
 }
 
 /*
+ * Activate High Speed or HS200 mode if supported.
+ */
+static int mmc_select_timing(struct mmc_card *card)
+{
+	int err = 0;
+
+	if ((card->csd.mmca_vsn < CSD_SPEC_VER_4 &&
+	     card->ext_csd.hs_max_dtr == 0))
+		goto bus_speed;
+
+	if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200)
+		err = mmc_select_hs200(card);
+	else if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS)
+		err = mmc_select_hs(card);
+
+	if (err && err != -EBADMSG)
+		return err;
+
+	if (err) {
+		pr_warn("%s: switch to %s failed\n",
+			mmc_card_hs(card) ? "high-speed" :
+			(mmc_card_hs200(card) ? "hs200" : ""),
+			mmc_hostname(card->host));
+		err = 0;
+	}
+
+bus_speed:
+	/*
+	 * Set the bus speed to the selected bus timing.
+	 * If timing is not selected, backward compatible is the default.
+	 */
+	mmc_set_bus_speed(card);
+	return err;
+}
+
+/*
+ * Execute tuning sequence to seek the proper bus operating
+ * conditions for HS200, which sends CMD21 to the device.
+ */
+static int mmc_hs200_tuning(struct mmc_card *card)
+{
+	struct mmc_host *host = card->host;
+	int err = 0;
+
+	if (host->ops->execute_tuning) {
+		mmc_host_clk_hold(host);
+		err = host->ops->execute_tuning(host,
+				MMC_SEND_TUNING_BLOCK_HS200);
+		mmc_host_clk_release(host);
+
+		if (err)
+			pr_warn("%s: tuning execution failed\n",
+				mmc_hostname(host));
+	}
+
+	return err;
+}
+
+/*
  * Handle the detection and initialisation of a card.
  *
  * In the case of a resume, "oldcard" will contain the card
@@ -909,9 +1093,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 	struct mmc_card *oldcard)
 {
 	struct mmc_card *card;
-	int err, ddr = 0;
+	int err;
 	u32 cid[4];
-	unsigned int max_dtr;
 	u32 rocr;
 	u8 *ext_csd = NULL;
 
@@ -1103,173 +1286,23 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 	}
 
 	/*
-	 * Activate high speed (if supported)
-	 */
-	if (card->ext_csd.hs_max_dtr != 0) {
-		err = 0;
-		if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200)
-			err = mmc_select_hs200(card);
-		else if	(card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS)
-			err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
-					EXT_CSD_HS_TIMING, 1,
-					card->ext_csd.generic_cmd6_time,
-					true, true, true);
-
-		if (err && err != -EBADMSG)
-			goto free_card;
-
-		if (err) {
-			pr_warning("%s: switch to highspeed failed\n",
-			       mmc_hostname(card->host));
-			err = 0;
-		} else {
-			if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200)
-				mmc_set_timing(card->host,
-					       MMC_TIMING_MMC_HS200);
-			else
-				mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
-		}
-	}
-
-	/*
-	 * Compute bus speed.
-	 */
-	max_dtr = (unsigned int)-1;
-
-	if (mmc_card_hs(card) || mmc_card_hs200(card)) {
-		if (max_dtr > card->ext_csd.hs_max_dtr)
-			max_dtr = card->ext_csd.hs_max_dtr;
-		if (mmc_card_hs(card) && (max_dtr > 52000000))
-			max_dtr = 52000000;
-	} else if (max_dtr > card->csd.max_dtr) {
-		max_dtr = card->csd.max_dtr;
-	}
-
-	mmc_set_clock(host, max_dtr);
-
-	/*
-	 * Indicate DDR mode (if supported).
+	 * Select timing interface
 	 */
-	if (mmc_card_hs(card))
-		ddr = card->mmc_avail_type & EXT_CSD_CARD_TYPE_DDR_52;
+	err = mmc_select_timing(card);
+	if (err)
+		goto free_card;
 
-	/*
-	 * Indicate HS200 SDR mode (if supported).
-	 */
 	if (mmc_card_hs200(card)) {
-		u32 ext_csd_bits;
-		u32 bus_width = card->host->ios.bus_width;
-
-		/*
-		 * For devices supporting HS200 mode, the bus width has
-		 * to be set before executing the tuning function. If
-		 * set before tuning, then device will respond with CRC
-		 * errors for responses on CMD line. So for HS200 the
-		 * sequence will be
-		 * 1. set bus width 4bit / 8 bit (1 bit not supported)
-		 * 2. switch to HS200 mode
-		 * 3. set the clock to > 52Mhz <=200MHz and
-		 * 4. execute tuning for HS200
-		 */
-		if (card->host->ops->execute_tuning) {
-			mmc_host_clk_hold(card->host);
-			err = card->host->ops->execute_tuning(card->host,
-				MMC_SEND_TUNING_BLOCK_HS200);
-			mmc_host_clk_release(card->host);
-		}
-		if (err) {
-			pr_warning("%s: tuning execution failed\n",
-				   mmc_hostname(card->host));
+		err = mmc_hs200_tuning(card);
+		if (err)
 			goto err;
-		}
-
-		ext_csd_bits = (bus_width == MMC_BUS_WIDTH_8) ?
-				EXT_CSD_BUS_WIDTH_8 : EXT_CSD_BUS_WIDTH_4;
-	}
-
-	/*
-	 * Activate wide bus and DDR (if supported).
-	 */
-	if (!mmc_card_hs200(card) &&
-	    (card->csd.mmca_vsn >= CSD_SPEC_VER_4) &&
-	    (host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA))) {
-		static unsigned ext_csd_bits[][2] = {
-			{ EXT_CSD_BUS_WIDTH_8, EXT_CSD_DDR_BUS_WIDTH_8 },
-			{ EXT_CSD_BUS_WIDTH_4, EXT_CSD_DDR_BUS_WIDTH_4 },
-			{ EXT_CSD_BUS_WIDTH_1, EXT_CSD_BUS_WIDTH_1 },
-		};
-		static unsigned bus_widths[] = {
-			MMC_BUS_WIDTH_8,
-			MMC_BUS_WIDTH_4,
-			MMC_BUS_WIDTH_1
-		};
-		unsigned idx, bus_width = 0;
-
-		if (host->caps & MMC_CAP_8_BIT_DATA)
-			idx = 0;
-		else
-			idx = 1;
-		for (; idx < ARRAY_SIZE(bus_widths); idx++) {
-			bus_width = bus_widths[idx];
-			if (bus_width == MMC_BUS_WIDTH_1)
-				ddr = 0; /* no DDR for 1-bit width */
-
-			err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
-					 EXT_CSD_BUS_WIDTH,
-					 ext_csd_bits[idx][0],
-					 card->ext_csd.generic_cmd6_time);
-			if (!err) {
-				mmc_set_bus_width(card->host, bus_width);
-
-				/*
-				 * If controller can't handle bus width test,
-				 * compare ext_csd previously read in 1 bit mode
-				 * against ext_csd at new bus width
-				 */
-				if (!(host->caps & MMC_CAP_BUS_WIDTH_TEST))
-					err = mmc_compare_ext_csds(card,
-						bus_width);
-				else
-					err = mmc_bus_test(card, bus_width);
-				if (!err)
-					break;
-			}
-		}
-
-		if (!err && ddr) {
-			err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
-					 EXT_CSD_BUS_WIDTH,
-					 ext_csd_bits[idx][1],
-					 card->ext_csd.generic_cmd6_time);
-		}
-		if (err) {
-			pr_warning("%s: switch to bus width %d ddr %d "
-				"failed\n", mmc_hostname(card->host),
-				1 << bus_width, ddr);
-			goto free_card;
-		} else if (ddr) {
-			/*
-			 * eMMC cards can support 3.3V to 1.2V i/o (vccq)
-			 * signaling.
-			 *
-			 * EXT_CSD_CARD_TYPE_DDR_1_8V means 3.3V or 1.8V vccq.
-			 *
-			 * 1.8V vccq at 3.3V core voltage (vcc) is not required
-			 * in the JEDEC spec for DDR.
-			 *
-			 * Do not force change in vccq since we are obviously
-			 * working and no change to vccq is needed.
-			 *
-			 * WARNING: eMMC rules are NOT the same as SD DDR
-			 */
-			if (ddr & EXT_CSD_CARD_TYPE_DDR_1_2V) {
-				err = __mmc_set_signal_voltage(host,
-					MMC_SIGNAL_VOLTAGE_120);
-				if (err)
-					goto err;
-			}
-			mmc_set_timing(card->host, MMC_TIMING_MMC_DDR52);
-			mmc_set_bus_width(card->host, bus_width);
+	} else if (mmc_card_hs(card)) {
+		/* Select the desired bus width optionally */
+		err = mmc_select_bus_width(card);
+		if (!IS_ERR_VALUE(err)) {
+			err = mmc_select_hs_ddr(card);
+			if (err)
+				goto err;
 		}
 	}