memstick: fix MSProHG 8-bit interface mode support

- 8-bit interface mode never worked properly.  The only adapter I have
  which supports the 8b mode (the Jmicron) had some problems with its
  clock wiring and they discovered it only now.  We also discovered that
  ProHG media is more sensitive to the ordering of initialization
  commands.

- Make the driver fall back to highest supported mode instead of always
  falling back to serial.  The driver will attempt the switch to 8b mode
  for any new MSPro card, but not all of them support it.  Previously,
  these new cards ended up in serial mode, which is not the best idea
  (they work fine with 4b, after all).

- Edit some macros for better conformance to Sony documentation

Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1 files changed, 27 insertions, 12 deletions

diff --git a/drivers/memstick/host/jmb38x_ms.c b/drivers/memstick/host/jmb38x_ms.c
index 3485c63..2fb95a5 100644
--- a/drivers/memstick/host/jmb38x_ms.c
+++ b/drivers/memstick/host/jmb38x_ms.c
@@ -81,6 +81,8 @@ struct jmb38x_ms {
 #define TPC_CODE_SZ_MASK       0x00000700
 #define TPC_DATA_SZ_MASK       0x00000007
 
+#define HOST_CONTROL_TDELAY_EN 0x00040000
+#define HOST_CONTROL_HW_OC_P   0x00010000
 #define HOST_CONTROL_RESET_REQ 0x00008000
 #define HOST_CONTROL_REI       0x00004000
 #define HOST_CONTROL_LED       0x00000400
@@ -88,6 +90,7 @@ struct jmb38x_ms {
 #define HOST_CONTROL_RESET     0x00000100
 #define HOST_CONTROL_POWER_EN  0x00000080
 #define HOST_CONTROL_CLOCK_EN  0x00000040
+#define HOST_CONTROL_REO       0x00000008
 #define HOST_CONTROL_IF_SHIFT  4
 
 #define HOST_CONTROL_IF_SERIAL 0x0
@@ -133,11 +136,15 @@ struct jmb38x_ms {
 #define PAD_PU_PD_ON_MS_SOCK1 0x0f0f0000
 
 #define CLOCK_CONTROL_40MHZ   0x00000001
-#define CLOCK_CONTROL_50MHZ   0x00000002
+#define CLOCK_CONTROL_50MHZ   0x0000000a
 #define CLOCK_CONTROL_60MHZ   0x00000008
 #define CLOCK_CONTROL_62_5MHZ 0x0000000c
 #define CLOCK_CONTROL_OFF     0x00000000
 
+#define PCI_CTL_CLOCK_DLY_ADDR   0x000000b0
+#define PCI_CTL_CLOCK_DLY_MASK_A 0x00000f00
+#define PCI_CTL_CLOCK_DLY_MASK_B 0x0000f000
+
 enum {
 	CMD_READY    = 0x01,
 	FIFO_READY   = 0x02,
@@ -367,8 +374,7 @@ static int jmb38x_ms_issue_cmd(struct memstick_host *msh)
 		return host->req->error;
 	}
 
-	dev_dbg(&msh->dev, "control %08x\n",
-		readl(host->addr + HOST_CONTROL));
+	dev_dbg(&msh->dev, "control %08x\n", readl(host->addr + HOST_CONTROL));
 	dev_dbg(&msh->dev, "status %08x\n", readl(host->addr + INT_STATUS));
 	dev_dbg(&msh->dev, "hstatus %08x\n", readl(host->addr + STATUS));
 
@@ -637,7 +643,7 @@ static int jmb38x_ms_reset(struct jmb38x_ms_host *host)
 		ndelay(20);
 	}
 	dev_dbg(&host->chip->pdev->dev, "reset_req timeout\n");
-	return -EIO;
+	/* return -EIO; */
 
 reset_next:
 	writel(HOST_CONTROL_RESET | HOST_CONTROL_CLOCK_EN
@@ -680,7 +686,9 @@ static int jmb38x_ms_set_param(struct memstick_host *msh,
 
 			host_ctl = 7;
 			host_ctl |= HOST_CONTROL_POWER_EN
-				 | HOST_CONTROL_CLOCK_EN;
+				    | HOST_CONTROL_CLOCK_EN
+				    | HOST_CONTROL_HW_OC_P
+				    | HOST_CONTROL_TDELAY_EN;
 			writel(host_ctl, host->addr + HOST_CONTROL);
 
 			writel(host->id ? PAD_PU_PD_ON_MS_SOCK1
@@ -704,33 +712,40 @@ static int jmb38x_ms_set_param(struct memstick_host *msh,
 		break;
 	case MEMSTICK_INTERFACE:
 		host_ctl &= ~(3 << HOST_CONTROL_IF_SHIFT);
+		pci_read_config_dword(host->chip->pdev,
+				      PCI_CTL_CLOCK_DLY_ADDR,
+				      &clock_delay);
+		clock_delay &= host->id ? ~PCI_CTL_CLOCK_DLY_MASK_B
+					: ~PCI_CTL_CLOCK_DLY_MASK_A;
 
 		if (value == MEMSTICK_SERIAL) {
 			host_ctl &= ~HOST_CONTROL_FAST_CLK;
+			host_ctl &= ~HOST_CONTROL_REO;
 			host_ctl |= HOST_CONTROL_IF_SERIAL
 				    << HOST_CONTROL_IF_SHIFT;
 			host_ctl |= HOST_CONTROL_REI;
 			clock_ctl = CLOCK_CONTROL_40MHZ;
-			clock_delay = 0;
 		} else if (value == MEMSTICK_PAR4) {
-			host_ctl |= HOST_CONTROL_FAST_CLK;
+			host_ctl |= HOST_CONTROL_FAST_CLK | HOST_CONTROL_REO;
 			host_ctl |= HOST_CONTROL_IF_PAR4
 				    << HOST_CONTROL_IF_SHIFT;
 			host_ctl &= ~HOST_CONTROL_REI;
 			clock_ctl = CLOCK_CONTROL_40MHZ;
-			clock_delay = 4;
+			clock_delay |= host->id ? (4 << 12) : (4 << 8);
 		} else if (value == MEMSTICK_PAR8) {
 			host_ctl |= HOST_CONTROL_FAST_CLK;
 			host_ctl |= HOST_CONTROL_IF_PAR8
 				    << HOST_CONTROL_IF_SHIFT;
-			host_ctl &= ~HOST_CONTROL_REI;
-			clock_ctl = CLOCK_CONTROL_60MHZ;
-			clock_delay = 0;
+			host_ctl &= ~(HOST_CONTROL_REI | HOST_CONTROL_REO);
+			clock_ctl = CLOCK_CONTROL_50MHZ;
 		} else
 			return -EINVAL;
+
 		writel(host_ctl, host->addr + HOST_CONTROL);
 		writel(clock_ctl, host->addr + CLOCK_CONTROL);
-		writel(clock_delay, host->addr + CLOCK_DELAY);
+		pci_write_config_dword(host->chip->pdev,
+				       PCI_CTL_CLOCK_DLY_ADDR,
+				       clock_delay);
 		break;
 	};
 	return 0;