[media] drxk: Add support for parallel mode and prints mpeg mode

While the driver has support for both serial and parallel mode,
There's was way to select serial mode via configuration. Add
a config option for that, while keeping the default in serial mode.

Also, at debug mode, it will now print a message when mpeg is
enabled/disabled, and showing if parallel or serial mode were
selected, helping developers to double-check if the DRX-K is at
the right mode.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

1 files changed, 8 insertions, 6 deletions

diff --git a/drivers/media/dvb/frontends/drxk_hard.c b/drivers/media/dvb/frontends/drxk_hard.c
index 817d3ec..c8213f6 100644
--- a/drivers/media/dvb/frontends/drxk_hard.c
+++ b/drivers/media/dvb/frontends/drxk_hard.c
@@ -660,7 +660,6 @@ static int init_state(struct drxk_state *state)
 	/* io_pad_cfg_mode output mode is drive always */
 	/* io_pad_cfg_drive is set to power 2 (23 mA) */
 	u32 ulGPIOCfg = 0x0113;
-	u32 ulSerialMode = 1;
 	u32 ulInvertTSClock = 0;
 	u32 ulTSDataStrength = DRXK_MPEG_SERIAL_OUTPUT_PIN_DRIVE_STRENGTH;
 	u32 ulTSClockkStrength = DRXK_MPEG_OUTPUT_CLK_DRIVE_STRENGTH;
@@ -811,8 +810,6 @@ static int init_state(struct drxk_state *state)
 	/* MPEG output configuration */
 	state->m_enableMPEGOutput = true;	/* If TRUE; enable MPEG ouput */
 	state->m_insertRSByte = false;	/* If TRUE; insert RS byte */
-	state->m_enableParallel = true;	/* If TRUE;
-					   parallel out otherwise serial */
 	state->m_invertDATA = false;	/* If TRUE; invert DATA signals */
 	state->m_invertERR = false;	/* If TRUE; invert ERR signal */
 	state->m_invertSTR = false;	/* If TRUE; invert STR signals */
@@ -857,8 +854,6 @@ static int init_state(struct drxk_state *state)
 	state->m_bPowerDown = false;
 	state->m_currentPowerMode = DRX_POWER_DOWN;
 
-	state->m_enableParallel = (ulSerialMode == 0);
-
 	state->m_rfmirror = (ulRfMirror == 0);
 	state->m_IfAgcPol = false;
 	return 0;
@@ -1195,7 +1190,9 @@ static int MPEGTSConfigurePins(struct drxk_state *state, bool mpegEnable)
 	u16 sioPdrMclkCfg = 0;
 	u16 sioPdrMdxCfg = 0;
 
-	dprintk(1, "\n");
+	dprintk(1, ": mpeg %s, %s mode\n",
+		mpegEnable ? "enable" : "disable",
+		state->m_enableParallel ? "parallel" : "serial");
 
 	/* stop lock indicator process */
 	status = write16(state, SCU_RAM_GPIO__A, SCU_RAM_GPIO_HW_LOCK_IND_DISABLE);
@@ -6432,6 +6429,11 @@ struct dvb_frontend *drxk_attach(const struct drxk_config *config,
 	state->antenna_dvbt = config->antenna_dvbt;
 	state->m_ChunkSize = config->chunk_size;
 
+	if (config->parallel_ts)
+		state->m_enableParallel = true;
+	else
+		state->m_enableParallel = false;
+
 	/* NOTE: as more UIO bits will be used, add them to the mask */
 	state->UIO_mask = config->antenna_gpio;