Merge branch 'i2c/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "I2C has for you two new drivers (Tegra BPMP and STM32F4), interrupt
  support for pca954x muxes, and a bunch of driver bugfixes and
  improvements. Nothing really special this cycle.

  A few commits have been added to my tree just recently. Those are the
  Tegra BPMP driver and a few straightforward bugfixes or cleanups which
  I prefer to have upstream rather soonish. The rest had proper
  linux-next exposure"

* 'i2c/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (25 commits)
  i2c: thunderx: Replace pci_enable_msix()
  i2c: exynos5: fix arbitration lost handling
  i2c: exynos5: disable fifo-almost-empty irq signal when necessary
  i2c: at91: ensure state is restored after suspending
  i2c: bcm2835: Avoid possible NULL ptr dereference
  i2c: Add Tegra BPMP I2C proxy driver
  dt-bindings: Add Tegra186 BPMP I2C binding
  misc: eeprom: at24: use device_property_*() functions instead of of_get_property()
  i2c: mux: pca954x: Add interrupt controller support
  dt: bindings: i2c-mux-pca954x: Add documentation for interrupt controller
  i2c: mux: pca954x: Add missing pca9542 definition to chip_desc
  i2c: riic: correctly finish transfers
  i2c: i801: Add support for Intel Gemini Lake
  i2c: mux: pca9541: Export OF device ID table as module aliases
  i2c: mux: pca954x: Export OF device ID table as module aliases
  i2c: mux: mlxcpld: remove unused including <linux/version.h>
  i2c: busses: constify i2c_algorithm structures
  i2c: i2c-mux-gpio: rename i2c-gpio-mux to i2c-mux-gpio
  i2c: sh_mobile: document support for r8a7796 (R-Car M3-W)
  i2c: i2c-cros-ec-tunnel: Reduce logging noise
  ...

31 files changed, 1555 insertions, 41 deletions

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 0cdc844..8adc0f1 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -128,6 +128,7 @@ config I2C_I801
 	    DNV (SOC)
 	    Broxton (SOC)
 	    Lewisburg (PCH)
+	    Gemini Lake (SOC)
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-i801.
@@ -886,6 +887,16 @@ config I2C_ST
 	  This driver can also be built as module. If so, the module
 	  will be called i2c-st.
 
+config I2C_STM32F4
+	tristate "STMicroelectronics STM32F4 I2C support"
+	depends on ARCH_STM32 || COMPILE_TEST
+	help
+	  Enable this option to add support for STM32 I2C controller embedded
+	  in STM32F4 SoCs.
+
+	  This driver can also be built as module. If so, the module
+	  will be called i2c-stm32f4.
+
 config I2C_STU300
 	tristate "ST Microelectronics DDC I2C interface"
 	depends on MACH_U300
@@ -919,6 +930,17 @@ config I2C_TEGRA
 	  If you say yes to this option, support will be included for the
 	  I2C controller embedded in NVIDIA Tegra SOCs
 
+config I2C_TEGRA_BPMP
+	tristate "NVIDIA Tegra BPMP I2C controller"
+	depends on TEGRA_BPMP
+	help
+	  If you say yes to this option, support will be included for the I2C
+	  controller embedded in NVIDIA Tegra SoCs accessed via the BPMP.
+
+	  This I2C driver is a 'virtual' I2C driver. The real driver is part
+	  of the BPMP firmware, and this driver merely communicates with that
+	  real driver.
+
 config I2C_UNIPHIER
 	tristate "UniPhier FIFO-less I2C controller"
 	depends on ARCH_UNIPHIER || COMPILE_TEST
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 1c1bac8..30b6085 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -85,9 +85,11 @@ obj-$(CONFIG_I2C_SH_MOBILE)	+= i2c-sh_mobile.o
 obj-$(CONFIG_I2C_SIMTEC)	+= i2c-simtec.o
 obj-$(CONFIG_I2C_SIRF)		+= i2c-sirf.o
 obj-$(CONFIG_I2C_ST)		+= i2c-st.o
+obj-$(CONFIG_I2C_STM32F4)	+= i2c-stm32f4.o
 obj-$(CONFIG_I2C_STU300)	+= i2c-stu300.o
 obj-$(CONFIG_I2C_SUN6I_P2WI)	+= i2c-sun6i-p2wi.o
 obj-$(CONFIG_I2C_TEGRA)		+= i2c-tegra.o
+obj-$(CONFIG_I2C_TEGRA_BPMP)	+= i2c-tegra-bpmp.o
 obj-$(CONFIG_I2C_UNIPHIER)	+= i2c-uniphier.o
 obj-$(CONFIG_I2C_UNIPHIER_F)	+= i2c-uniphier-f.o
 obj-$(CONFIG_I2C_VERSATILE)	+= i2c-versatile.o
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 0b86c61..fabbb9e 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -820,7 +820,7 @@ static u32 at91_twi_func(struct i2c_adapter *adapter)
 		| I2C_FUNC_SMBUS_READ_BLOCK_DATA;
 }
 
-static struct i2c_algorithm at91_twi_algorithm = {
+static const struct i2c_algorithm at91_twi_algorithm = {
 	.master_xfer	= at91_twi_xfer,
 	.functionality	= at91_twi_func,
 };
@@ -1180,6 +1180,7 @@ static int at91_twi_suspend_noirq(struct device *dev)
 
 static int at91_twi_resume_noirq(struct device *dev)
 {
+	struct at91_twi_dev *twi_dev = dev_get_drvdata(dev);
 	int ret;
 
 	if (!pm_runtime_status_suspended(dev)) {
@@ -1191,6 +1192,8 @@ static int at91_twi_resume_noirq(struct device *dev)
 	pm_runtime_mark_last_busy(dev);
 	pm_request_autosuspend(dev);
 
+	at91_init_twi_bus(twi_dev);
+
 	return 0;
 }
 
diff --git a/drivers/i2c/busses/i2c-bcm2835.c b/drivers/i2c/busses/i2c-bcm2835.c
index c3436f6..cd07a69 100644
--- a/drivers/i2c/busses/i2c-bcm2835.c
+++ b/drivers/i2c/busses/i2c-bcm2835.c
@@ -195,7 +195,9 @@ static irqreturn_t bcm2835_i2c_isr(int this_irq, void *data)
 	}
 
 	if (val & BCM2835_I2C_S_DONE) {
-		if (i2c_dev->curr_msg->flags & I2C_M_RD) {
+		if (!i2c_dev->curr_msg) {
+			dev_err(i2c_dev->dev, "Got unexpected interrupt (from firmware?)\n");
+		} else if (i2c_dev->curr_msg->flags & I2C_M_RD) {
 			bcm2835_drain_rxfifo(i2c_dev);
 			val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S);
 		}
diff --git a/drivers/i2c/busses/i2c-bfin-twi.c b/drivers/i2c/busses/i2c-bfin-twi.c
index 29d00c4..9fe942b 100644
--- a/drivers/i2c/busses/i2c-bfin-twi.c
+++ b/drivers/i2c/busses/i2c-bfin-twi.c
@@ -563,7 +563,7 @@ static u32 bfin_twi_functionality(struct i2c_adapter *adap)
 	       I2C_FUNC_I2C | I2C_FUNC_SMBUS_I2C_BLOCK;
 }
 
-static struct i2c_algorithm bfin_twi_algorithm = {
+static const struct i2c_algorithm bfin_twi_algorithm = {
 	.master_xfer   = bfin_twi_master_xfer,
 	.smbus_xfer    = bfin_twi_smbus_xfer,
 	.functionality = bfin_twi_functionality,
diff --git a/drivers/i2c/busses/i2c-cros-ec-tunnel.c b/drivers/i2c/busses/i2c-cros-ec-tunnel.c
index 9b36a7b..eb76b76 100644
--- a/drivers/i2c/busses/i2c-cros-ec-tunnel.c
+++ b/drivers/i2c/busses/i2c-cros-ec-tunnel.c
@@ -154,8 +154,10 @@ static int ec_i2c_parse_response(const u8 *buf, struct i2c_msg i2c_msgs[],
 	resp = (const struct ec_response_i2c_passthru *)buf;
 	if (resp->i2c_status & EC_I2C_STATUS_TIMEOUT)
 		return -ETIMEDOUT;
+	else if (resp->i2c_status & EC_I2C_STATUS_NAK)
+		return -ENXIO;
 	else if (resp->i2c_status & EC_I2C_STATUS_ERROR)
-		return -EREMOTEIO;
+		return -EIO;
 
 	/* Other side could send us back fewer messages, but not more */
 	if (resp->num_msgs > *num)
@@ -222,10 +224,8 @@ static int ec_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg i2c_msgs[],
 	}
 
 	result = ec_i2c_parse_response(msg->data, i2c_msgs, &num);
-	if (result < 0) {
-		dev_err(dev, "Error parsing EC i2c message %d\n", result);
+	if (result < 0)
 		goto exit;
-	}
 
 	/* Indicate success by saying how many messages were sent */
 	result = num;
diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
index e9db857..7a3faa5 100644
--- a/drivers/i2c/busses/i2c-designware-core.c
+++ b/drivers/i2c/busses/i2c-designware-core.c
@@ -820,7 +820,7 @@ static u32 i2c_dw_func(struct i2c_adapter *adap)
 	return dev->functionality;
 }
 
-static struct i2c_algorithm i2c_dw_algo = {
+static const struct i2c_algorithm i2c_dw_algo = {
 	.master_xfer	= i2c_dw_xfer,
 	.functionality	= i2c_dw_func,
 };
diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c
index 5ce71ce..bdeab01 100644
--- a/drivers/i2c/busses/i2c-eg20t.c
+++ b/drivers/i2c/busses/i2c-eg20t.c
@@ -715,7 +715,7 @@ static u32 pch_i2c_func(struct i2c_adapter *adap)
 	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR;
 }
 
-static struct i2c_algorithm pch_algorithm = {
+static const struct i2c_algorithm pch_algorithm = {
 	.master_xfer = pch_i2c_xfer,
 	.functionality = pch_i2c_func
 };
diff --git a/drivers/i2c/busses/i2c-emev2.c b/drivers/i2c/busses/i2c-emev2.c
index 96bb4e7..3129127 100644
--- a/drivers/i2c/busses/i2c-emev2.c
+++ b/drivers/i2c/busses/i2c-emev2.c
@@ -347,7 +347,7 @@ static int em_i2c_unreg_slave(struct i2c_client *slave)
 	return 0;
 }
 
-static struct i2c_algorithm em_i2c_algo = {
+static const struct i2c_algorithm em_i2c_algo = {
 	.master_xfer = em_i2c_xfer,
 	.functionality = em_i2c_func,
 	.reg_slave      = em_i2c_reg_slave,
diff --git a/drivers/i2c/busses/i2c-exynos5.c b/drivers/i2c/busses/i2c-exynos5.c
index bea6071..cbd93ce 100644
--- a/drivers/i2c/busses/i2c-exynos5.c
+++ b/drivers/i2c/busses/i2c-exynos5.c
@@ -130,12 +130,32 @@
 /* I2C_TRANS_STATUS register bits */
 #define HSI2C_MASTER_BUSY			(1u << 17)
 #define HSI2C_SLAVE_BUSY			(1u << 16)
+
+/* I2C_TRANS_STATUS register bits for Exynos5 variant */
 #define HSI2C_TIMEOUT_AUTO			(1u << 4)
 #define HSI2C_NO_DEV				(1u << 3)
 #define HSI2C_NO_DEV_ACK			(1u << 2)
 #define HSI2C_TRANS_ABORT			(1u << 1)
 #define HSI2C_TRANS_DONE			(1u << 0)
 
+/* I2C_TRANS_STATUS register bits for Exynos7 variant */
+#define HSI2C_MASTER_ST_MASK			0xf
+#define HSI2C_MASTER_ST_IDLE			0x0
+#define HSI2C_MASTER_ST_START			0x1
+#define HSI2C_MASTER_ST_RESTART			0x2
+#define HSI2C_MASTER_ST_STOP			0x3
+#define HSI2C_MASTER_ST_MASTER_ID		0x4
+#define HSI2C_MASTER_ST_ADDR0			0x5
+#define HSI2C_MASTER_ST_ADDR1			0x6
+#define HSI2C_MASTER_ST_ADDR2			0x7
+#define HSI2C_MASTER_ST_ADDR_SR			0x8
+#define HSI2C_MASTER_ST_READ			0x9
+#define HSI2C_MASTER_ST_WRITE			0xa
+#define HSI2C_MASTER_ST_NO_ACK			0xb
+#define HSI2C_MASTER_ST_LOSE			0xc
+#define HSI2C_MASTER_ST_WAIT			0xd
+#define HSI2C_MASTER_ST_WAIT_CMD		0xe
+
 /* I2C_ADDR register bits */
 #define HSI2C_SLV_ADDR_SLV(x)			((x & 0x3ff) << 0)
 #define HSI2C_SLV_ADDR_MAS(x)			((x & 0x3ff) << 10)
@@ -437,6 +457,7 @@ static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
 
 	int_status = readl(i2c->regs + HSI2C_INT_STATUS);
 	writel(int_status, i2c->regs + HSI2C_INT_STATUS);
+	trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
 
 	/* handle interrupt related to the transfer status */
 	if (i2c->variant->hw == HSI2C_EXYNOS7) {
@@ -460,8 +481,12 @@ static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
 			i2c->state = -ETIMEDOUT;
 			goto stop;
 		}
+
+		if ((trans_status & HSI2C_MASTER_ST_MASK) == HSI2C_MASTER_ST_LOSE) {
+			i2c->state = -EAGAIN;
+			goto stop;
+		}
 	} else if (int_status & HSI2C_INT_I2C) {
-		trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
 		if (trans_status & HSI2C_NO_DEV_ACK) {
 			dev_dbg(i2c->dev, "No ACK from device\n");
 			i2c->state = -ENXIO;
@@ -502,8 +527,13 @@ static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
 		fifo_level = HSI2C_TX_FIFO_LVL(fifo_status);
 
 		len = i2c->variant->fifo_depth - fifo_level;
-		if (len > (i2c->msg->len - i2c->msg_ptr))
+		if (len > (i2c->msg->len - i2c->msg_ptr)) {
+			u32 int_en = readl(i2c->regs + HSI2C_INT_ENABLE);
+
+			int_en &= ~HSI2C_INT_TX_ALMOSTEMPTY_EN;
+			writel(int_en, i2c->regs + HSI2C_INT_ENABLE);
 			len = i2c->msg->len - i2c->msg_ptr;
+		}
 
 		while (len > 0) {
 			byte = i2c->msg->buf[i2c->msg_ptr++];
diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c
index e242db4..6484fa6 100644
--- a/drivers/i2c/busses/i2c-i801.c
+++ b/drivers/i2c/busses/i2c-i801.c
@@ -65,6 +65,7 @@
  * Lewisburg (PCH)		0xa1a3	32	hard	yes	yes	yes
  * Lewisburg Supersku (PCH)	0xa223	32	hard	yes	yes	yes
  * Kaby Lake PCH-H (PCH)	0xa2a3	32	hard	yes	yes	yes
+ * Gemini Lake (SOC)		0x31d4	32	hard	yes	yes	yes
  *
  * Features supported by this driver:
  * Software PEC				no
@@ -213,6 +214,7 @@
 #define PCI_DEVICE_ID_INTEL_BRASWELL_SMBUS		0x2292
 #define PCI_DEVICE_ID_INTEL_DH89XXCC_SMBUS		0x2330
 #define PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS		0x23b0
+#define PCI_DEVICE_ID_INTEL_GEMINILAKE_SMBUS		0x31d4
 #define PCI_DEVICE_ID_INTEL_5_3400_SERIES_SMBUS		0x3b30
 #define PCI_DEVICE_ID_INTEL_BROXTON_SMBUS		0x5ad4
 #define PCI_DEVICE_ID_INTEL_LYNXPOINT_SMBUS		0x8c22
@@ -1012,6 +1014,7 @@ static const struct pci_device_id i801_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS1) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WELLSBURG_SMBUS_MS2) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_COLETOCREEK_SMBUS) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_GEMINILAKE_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WILDCATPOINT_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_SMBUS) },
 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_BAYTRAIL_SMBUS) },
diff --git a/drivers/i2c/busses/i2c-imx-lpi2c.c b/drivers/i2c/busses/i2c-imx-lpi2c.c
index 3310f2e..e86801a 100644
--- a/drivers/i2c/busses/i2c-imx-lpi2c.c
+++ b/drivers/i2c/busses/i2c-imx-lpi2c.c
@@ -538,7 +538,7 @@ static u32 lpi2c_imx_func(struct i2c_adapter *adapter)
 		I2C_FUNC_SMBUS_READ_BLOCK_DATA;
 }
 
-static struct i2c_algorithm lpi2c_imx_algo = {
+static const struct i2c_algorithm lpi2c_imx_algo = {
 	.master_xfer	= lpi2c_imx_xfer,
 	.functionality	= lpi2c_imx_func,
 };
diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index 47fc1f1..95ed171 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -1037,7 +1037,7 @@ static u32 i2c_imx_func(struct i2c_adapter *adapter)
 		| I2C_FUNC_SMBUS_READ_BLOCK_DATA;
 }
 
-static struct i2c_algorithm i2c_imx_algo = {
+static const struct i2c_algorithm i2c_imx_algo = {
 	.master_xfer	= i2c_imx_xfer,
 	.functionality	= i2c_imx_func,
 };
diff --git a/drivers/i2c/busses/i2c-mv64xxx.c b/drivers/i2c/busses/i2c-mv64xxx.c
index b4dec08..a50bd68 100644
--- a/drivers/i2c/busses/i2c-mv64xxx.c
+++ b/drivers/i2c/busses/i2c-mv64xxx.c
@@ -977,11 +977,32 @@ mv64xxx_i2c_remove(struct platform_device *dev)
 	return 0;
 }
 
+#ifdef CONFIG_PM
+static int mv64xxx_i2c_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct mv64xxx_i2c_data *drv_data = platform_get_drvdata(pdev);
+
+	mv64xxx_i2c_hw_init(drv_data);
+
+	return 0;
+}
+
+static const struct dev_pm_ops mv64xxx_i2c_pm = {
+	.resume = mv64xxx_i2c_resume,
+};
+
+#define mv64xxx_i2c_pm_ops (&mv64xxx_i2c_pm)
+#else
+#define mv64xxx_i2c_pm_ops NULL
+#endif
+
 static struct platform_driver mv64xxx_i2c_driver = {
 	.probe	= mv64xxx_i2c_probe,
 	.remove	= mv64xxx_i2c_remove,
 	.driver	= {
 		.name	= MV64XXX_I2C_CTLR_NAME,
+		.pm     = mv64xxx_i2c_pm_ops,
 		.of_match_table = mv64xxx_i2c_of_match_table,
 	},
 };
diff --git a/drivers/i2c/busses/i2c-nforce2.c b/drivers/i2c/busses/i2c-nforce2.c
index 374b35e..3241bb9 100644
--- a/drivers/i2c/busses/i2c-nforce2.c
+++ b/drivers/i2c/busses/i2c-nforce2.c
@@ -296,7 +296,7 @@ static u32 nforce2_func(struct i2c_adapter *adapter)
 		I2C_FUNC_SMBUS_BLOCK_DATA : 0);
 }
 
-static struct i2c_algorithm smbus_algorithm = {
+static const struct i2c_algorithm smbus_algorithm = {
 	.smbus_xfer	= nforce2_access,
 	.functionality	= nforce2_func,
 };
diff --git a/drivers/i2c/busses/i2c-octeon-core.h b/drivers/i2c/busses/i2c-octeon-core.h
index e160f83..aa3c8f4 100644
--- a/drivers/i2c/busses/i2c-octeon-core.h
+++ b/drivers/i2c/busses/i2c-octeon-core.h
@@ -6,7 +6,6 @@
 #include <linux/i2c-smbus.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
-#include <linux/pci.h>
 
 /* Controller command patterns */
 #define SW_TWSI_V		BIT_ULL(63)	/* Valid bit */
@@ -118,9 +117,6 @@ struct octeon_i2c {
 	void (*hlc_int_disable)(struct octeon_i2c *);
 	atomic_t int_enable_cnt;
 	atomic_t hlc_int_enable_cnt;
-#if IS_ENABLED(CONFIG_I2C_THUNDERX)
-	struct msix_entry i2c_msix;
-#endif
 	struct i2c_smbus_alert_setup alert_data;
 	struct i2c_client *ara;
 };
diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c
index c7da0c4..1ebb5e9 100644
--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -1504,7 +1504,7 @@ static int omap_i2c_runtime_resume(struct device *dev)
 	return 0;
 }
 
-static struct dev_pm_ops omap_i2c_pm_ops = {
+static const struct dev_pm_ops omap_i2c_pm_ops = {
 	SET_RUNTIME_PM_OPS(omap_i2c_runtime_suspend,
 			   omap_i2c_runtime_resume, NULL)
 };
diff --git a/drivers/i2c/busses/i2c-riic.c b/drivers/i2c/busses/i2c-riic.c
index 6263ea8..8f11d34 100644
--- a/drivers/i2c/busses/i2c-riic.c
+++ b/drivers/i2c/busses/i2c-riic.c
@@ -80,6 +80,7 @@
 #define ICIER_TEIE	0x40
 #define ICIER_RIE	0x20
 #define ICIER_NAKIE	0x10
+#define ICIER_SPIE	0x08
 
 #define ICSR2_NACKF	0x10
 
@@ -216,11 +217,10 @@ static irqreturn_t riic_tend_isr(int irq, void *data)
 		return IRQ_NONE;
 	}
 
-	if (riic->is_last || riic->err)
+	if (riic->is_last || riic->err) {
+		riic_clear_set_bit(riic, 0, ICIER_SPIE, RIIC_ICIER);
 		writeb(ICCR2_SP, riic->base + RIIC_ICCR2);
-
-	writeb(0, riic->base + RIIC_ICIER);
-	complete(&riic->msg_done);
+	}
 
 	return IRQ_HANDLED;
 }
@@ -240,13 +240,13 @@ static irqreturn_t riic_rdrf_isr(int irq, void *data)
 
 	if (riic->bytes_left == 1) {
 		/* STOP must come before we set ACKBT! */
-		if (riic->is_last)
+		if (riic->is_last) {
+			riic_clear_set_bit(riic, 0, ICIER_SPIE, RIIC_ICIER);
 			writeb(ICCR2_SP, riic->base + RIIC_ICCR2);
+		}
 
 		riic_clear_set_bit(riic, 0, ICMR3_ACKBT, RIIC_ICMR3);
 
-		writeb(0, riic->base + RIIC_ICIER);
-		complete(&riic->msg_done);
 	} else {
 		riic_clear_set_bit(riic, ICMR3_ACKBT, 0, RIIC_ICMR3);
 	}
@@ -259,6 +259,21 @@ static irqreturn_t riic_rdrf_isr(int irq, void *data)
 	return IRQ_HANDLED;
 }
 
+static irqreturn_t riic_stop_isr(int irq, void *data)
+{
+	struct riic_dev *riic = data;
+
+	/* read back registers to confirm writes have fully propagated */
+	writeb(0, riic->base + RIIC_ICSR2);
+	readb(riic->base + RIIC_ICSR2);
+	writeb(0, riic->base + RIIC_ICIER);
+	readb(riic->base + RIIC_ICIER);
+
+	complete(&riic->msg_done);
+
+	return IRQ_HANDLED;
+}
+
 static u32 riic_func(struct i2c_adapter *adap)
 {
 	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
@@ -326,6 +341,7 @@ static struct riic_irq_desc riic_irqs[] = {
 	{ .res_num = 0, .isr = riic_tend_isr, .name = "riic-tend" },
 	{ .res_num = 1, .isr = riic_rdrf_isr, .name = "riic-rdrf" },
 	{ .res_num = 2, .isr = riic_tdre_isr, .name = "riic-tdre" },
+	{ .res_num = 3, .isr = riic_stop_isr, .name = "riic-stop" },
 	{ .res_num = 5, .isr = riic_tend_isr, .name = "riic-nack" },
 };
 
diff --git a/drivers/i2c/busses/i2c-robotfuzz-osif.c b/drivers/i2c/busses/i2c-robotfuzz-osif.c
index 89d8b41..9c0f52b 100644
--- a/drivers/i2c/busses/i2c-robotfuzz-osif.c
+++ b/drivers/i2c/busses/i2c-robotfuzz-osif.c
@@ -117,7 +117,7 @@ static u32 osif_func(struct i2c_adapter *adapter)
 	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
 }
 
-static struct i2c_algorithm osif_algorithm = {
+static const struct i2c_algorithm osif_algorithm = {
 	.master_xfer	= osif_xfer,
 	.functionality	= osif_func,
 };
diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c
index 3d9ebe6..3d75593 100644
--- a/drivers/i2c/busses/i2c-sh_mobile.c
+++ b/drivers/i2c/busses/i2c-sh_mobile.c
@@ -781,7 +781,7 @@ static u32 sh_mobile_i2c_func(struct i2c_adapter *adapter)
 	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING;
 }
 
-static struct i2c_algorithm sh_mobile_i2c_algorithm = {
+static const struct i2c_algorithm sh_mobile_i2c_algorithm = {
 	.functionality	= sh_mobile_i2c_func,
 	.master_xfer	= sh_mobile_i2c_xfer,
 };
diff --git a/drivers/i2c/busses/i2c-st.c b/drivers/i2c/busses/i2c-st.c
index 1371547..1eb9fa8 100644
--- a/drivers/i2c/busses/i2c-st.c
+++ b/drivers/i2c/busses/i2c-st.c
@@ -776,7 +776,7 @@ static u32 st_i2c_func(struct i2c_adapter *adap)
 	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
 }
 
-static struct i2c_algorithm st_i2c_algo = {
+static const struct i2c_algorithm st_i2c_algo = {
 	.master_xfer = st_i2c_xfer,
 	.functionality = st_i2c_func,
 };
diff --git a/drivers/i2c/busses/i2c-stm32f4.c b/drivers/i2c/busses/i2c-stm32f4.c
new file mode 100644
index 0000000..f9dd7e8
--- /dev/null
+++ b/drivers/i2c/busses/i2c-stm32f4.c
@@ -0,0 +1,897 @@
+/*
+ * Driver for STMicroelectronics STM32 I2C controller
+ *
+ * This I2C controller is described in the STM32F429/439 Soc reference manual.
+ * Please see below a link to the documentation:
+ * http://www.st.com/resource/en/reference_manual/DM00031020.pdf
+ *
+ * Copyright (C) M'boumba Cedric Madianga 2016
+ * Author: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
+ *
+ * This driver is based on i2c-st.c
+ *
+ * License terms:  GNU General Public License (GPL), version 2
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+/* STM32F4 I2C offset registers */
+#define STM32F4_I2C_CR1			0x00
+#define STM32F4_I2C_CR2			0x04
+#define STM32F4_I2C_DR			0x10
+#define STM32F4_I2C_SR1			0x14
+#define STM32F4_I2C_SR2			0x18
+#define STM32F4_I2C_CCR			0x1C
+#define STM32F4_I2C_TRISE		0x20
+#define STM32F4_I2C_FLTR		0x24
+
+/* STM32F4 I2C control 1*/
+#define STM32F4_I2C_CR1_POS		BIT(11)
+#define STM32F4_I2C_CR1_ACK		BIT(10)
+#define STM32F4_I2C_CR1_STOP		BIT(9)
+#define STM32F4_I2C_CR1_START		BIT(8)
+#define STM32F4_I2C_CR1_PE		BIT(0)
+
+/* STM32F4 I2C control 2 */
+#define STM32F4_I2C_CR2_FREQ_MASK	GENMASK(5, 0)
+#define STM32F4_I2C_CR2_FREQ(n)		((n) & STM32F4_I2C_CR2_FREQ_MASK)
+#define STM32F4_I2C_CR2_ITBUFEN		BIT(10)
+#define STM32F4_I2C_CR2_ITEVTEN		BIT(9)
+#define STM32F4_I2C_CR2_ITERREN		BIT(8)
+#define STM32F4_I2C_CR2_IRQ_MASK	(STM32F4_I2C_CR2_ITBUFEN | \
+					 STM32F4_I2C_CR2_ITEVTEN | \
+					 STM32F4_I2C_CR2_ITERREN)
+
+/* STM32F4 I2C Status 1 */
+#define STM32F4_I2C_SR1_AF		BIT(10)
+#define STM32F4_I2C_SR1_ARLO		BIT(9)
+#define STM32F4_I2C_SR1_BERR		BIT(8)
+#define STM32F4_I2C_SR1_TXE		BIT(7)
+#define STM32F4_I2C_SR1_RXNE		BIT(6)
+#define STM32F4_I2C_SR1_BTF		BIT(2)
+#define STM32F4_I2C_SR1_ADDR		BIT(1)
+#define STM32F4_I2C_SR1_SB		BIT(0)
+#define STM32F4_I2C_SR1_ITEVTEN_MASK	(STM32F4_I2C_SR1_BTF | \
+					 STM32F4_I2C_SR1_ADDR | \
+					 STM32F4_I2C_SR1_SB)
+#define STM32F4_I2C_SR1_ITBUFEN_MASK	(STM32F4_I2C_SR1_TXE | \
+					 STM32F4_I2C_SR1_RXNE)
+#define STM32F4_I2C_SR1_ITERREN_MASK	(STM32F4_I2C_SR1_AF | \
+					 STM32F4_I2C_SR1_ARLO | \
+					 STM32F4_I2C_SR1_BERR)
+
+/* STM32F4 I2C Status 2 */
+#define STM32F4_I2C_SR2_BUSY		BIT(1)
+
+/* STM32F4 I2C Control Clock */
+#define STM32F4_I2C_CCR_CCR_MASK	GENMASK(11, 0)
+#define STM32F4_I2C_CCR_CCR(n)		((n) & STM32F4_I2C_CCR_CCR_MASK)
+#define STM32F4_I2C_CCR_FS		BIT(15)
+#define STM32F4_I2C_CCR_DUTY		BIT(14)
+
+/* STM32F4 I2C Trise */
+#define STM32F4_I2C_TRISE_VALUE_MASK	GENMASK(5, 0)
+#define STM32F4_I2C_TRISE_VALUE(n)	((n) & STM32F4_I2C_TRISE_VALUE_MASK)
+
+#define STM32F4_I2C_MIN_STANDARD_FREQ	2U
+#define STM32F4_I2C_MIN_FAST_FREQ	6U
+#define STM32F4_I2C_MAX_FREQ		46U
+#define HZ_TO_MHZ			1000000
+
+enum stm32f4_i2c_speed {
+	STM32F4_I2C_SPEED_STANDARD, /* 100 kHz */
+	STM32F4_I2C_SPEED_FAST, /* 400 kHz */
+	STM32F4_I2C_SPEED_END,
+};
+
+/**
+ * struct stm32f4_i2c_msg - client specific data
+ * @addr: 8-bit slave addr, including r/w bit
+ * @count: number of bytes to be transferred
+ * @buf: data buffer
+ * @result: result of the transfer
+ * @stop: last I2C msg to be sent, i.e. STOP to be generated
+ */
+struct stm32f4_i2c_msg {
+	u8 addr;
+	u32 count;
+	u8 *buf;
+	int result;
+	bool stop;
+};
+
+/**
+ * struct stm32f4_i2c_dev - private data of the controller
+ * @adap: I2C adapter for this controller
+ * @dev: device for this controller
+ * @base: virtual memory area
+ * @complete: completion of I2C message
+ * @clk: hw i2c clock
+ * @speed: I2C clock frequency of the controller. Standard or Fast are supported
+ * @parent_rate: I2C clock parent rate in MHz
+ * @msg: I2C transfer information
+ */
+struct stm32f4_i2c_dev {
+	struct i2c_adapter adap;
+	struct device *dev;
+	void __iomem *base;
+	struct completion complete;
+	struct clk *clk;
+	int speed;
+	int parent_rate;
+	struct stm32f4_i2c_msg msg;
+};
+
+static inline void stm32f4_i2c_set_bits(void __iomem *reg, u32 mask)
+{
+	writel_relaxed(readl_relaxed(reg) | mask, reg);
+}
+
+static inline void stm32f4_i2c_clr_bits(void __iomem *reg, u32 mask)
+{
+	writel_relaxed(readl_relaxed(reg) & ~mask, reg);
+}
+
+static void stm32f4_i2c_disable_irq(struct stm32f4_i2c_dev *i2c_dev)
+{
+	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
+
+	stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_IRQ_MASK);
+}
+
+static int stm32f4_i2c_set_periph_clk_freq(struct stm32f4_i2c_dev *i2c_dev)
+{
+	u32 freq;
+	u32 cr2 = 0;
+
+	i2c_dev->parent_rate = clk_get_rate(i2c_dev->clk);
+	freq = DIV_ROUND_UP(i2c_dev->parent_rate, HZ_TO_MHZ);
+
+	if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD) {
+		/*
+		 * To reach 100 kHz, the parent clk frequency should be between
+		 * a minimum value of 2 MHz and a maximum value of 46 MHz due
+		 * to hardware limitation
+		 */
+		if (freq < STM32F4_I2C_MIN_STANDARD_FREQ ||
+		    freq > STM32F4_I2C_MAX_FREQ) {
+			dev_err(i2c_dev->dev,
+				"bad parent clk freq for standard mode\n");
+			return -EINVAL;
+		}
+	} else {
+		/*
+		 * To be as close as possible to 400 kHz, the parent clk
+		 * frequency should be between a minimum value of 6 MHz and a
+		 * maximum value of 46 MHz due to hardware limitation
+		 */
+		if (freq < STM32F4_I2C_MIN_FAST_FREQ ||
+		    freq > STM32F4_I2C_MAX_FREQ) {
+			dev_err(i2c_dev->dev,
+				"bad parent clk freq for fast mode\n");
+			return -EINVAL;
+		}
+	}
+
+	cr2 |= STM32F4_I2C_CR2_FREQ(freq);
+	writel_relaxed(cr2, i2c_dev->base + STM32F4_I2C_CR2);
+
+	return 0;
+}
+
+static void stm32f4_i2c_set_rise_time(struct stm32f4_i2c_dev *i2c_dev)
+{
+	u32 freq = DIV_ROUND_UP(i2c_dev->parent_rate, HZ_TO_MHZ);
+	u32 trise;
+
+	/*
+	 * These bits must be programmed with the maximum SCL rise time given in
+	 * the I2C bus specification, incremented by 1.
+	 *
+	 * In standard mode, the maximum allowed SCL rise time is 1000 ns.
+	 * If, in the I2C_CR2 register, the value of FREQ[5:0] bits is equal to
+	 * 0x08 so period = 125 ns therefore the TRISE[5:0] bits must be
+	 * programmed with 0x9. (1000 ns / 125 ns + 1)
+	 * So, for I2C standard mode TRISE = FREQ[5:0] + 1
+	 *
+	 * In fast mode, the maximum allowed SCL rise time is 300 ns.
+	 * If, in the I2C_CR2 register, the value of FREQ[5:0] bits is equal to
+	 * 0x08 so period = 125 ns therefore the TRISE[5:0] bits must be
+	 * programmed with 0x3. (300 ns / 125 ns + 1)
+	 * So, for I2C fast mode TRISE = FREQ[5:0] * 300 / 1000 + 1
+	 *
+	 * Function stm32f4_i2c_set_periph_clk_freq made sure that parent rate
+	 * is not higher than 46 MHz . As a result trise is at most 4 bits wide
+	 * and so fits into the TRISE bits [5:0].
+	 */
+	if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD)
+		trise = freq + 1;
+	else
+		trise = freq * 3 / 10 + 1;
+
+	writel_relaxed(STM32F4_I2C_TRISE_VALUE(trise),
+		       i2c_dev->base + STM32F4_I2C_TRISE);
+}
+
+static void stm32f4_i2c_set_speed_mode(struct stm32f4_i2c_dev *i2c_dev)
+{
+	u32 val;
+	u32 ccr = 0;
+
+	if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD) {
+		/*
+		 * In standard mode:
+		 * t_scl_high = t_scl_low = CCR * I2C parent clk period
+		 * So to reach 100 kHz, we have:
+		 * CCR = I2C parent rate / 100 kHz >> 1
+		 *
+		 * For example with parent rate = 2 MHz:
+		 * CCR = 2000000 / (100000 << 1) = 10
+		 * t_scl_high = t_scl_low = 10 * (1 / 2000000) = 5000 ns
+		 * t_scl_high + t_scl_low = 10000 ns so 100 kHz is reached
+		 *
+		 * Function stm32f4_i2c_set_periph_clk_freq made sure that
+		 * parent rate is not higher than 46 MHz . As a result val
+		 * is at most 8 bits wide and so fits into the CCR bits [11:0].
+		 */
+		val = i2c_dev->parent_rate / (100000 << 1);
+	} else {
+		/*
+		 * In fast mode, we compute CCR with duty = 0 as with low
+		 * frequencies we are not able to reach 400 kHz.
+		 * In that case:
+		 * t_scl_high = CCR * I2C parent clk period
+		 * t_scl_low = 2 * CCR * I2C parent clk period
+		 * So, CCR = I2C parent rate / (400 kHz * 3)
+		 *
+		 * For example with parent rate = 6 MHz:
+		 * CCR = 6000000 / (400000 * 3) = 5
+		 * t_scl_high = 5 * (1 / 6000000) = 833 ns > 600 ns
+		 * t_scl_low = 2 * 5 * (1 / 6000000) = 1667 ns > 1300 ns
+		 * t_scl_high + t_scl_low = 2500 ns so 400 kHz is reached
+		 *
+		 * Function stm32f4_i2c_set_periph_clk_freq made sure that
+		 * parent rate is not higher than 46 MHz . As a result val
+		 * is at most 6 bits wide and so fits into the CCR bits [11:0].
+		 */
+		val = DIV_ROUND_UP(i2c_dev->parent_rate, 400000 * 3);
+
+		/* Select Fast mode */
+		ccr |= STM32F4_I2C_CCR_FS;
+	}
+
+	ccr |= STM32F4_I2C_CCR_CCR(val);
+	writel_relaxed(ccr, i2c_dev->base + STM32F4_I2C_CCR);
+}
+
+/**
+ * stm32f4_i2c_hw_config() - Prepare I2C block
+ * @i2c_dev: Controller's private data
+ */
+static int stm32f4_i2c_hw_config(struct stm32f4_i2c_dev *i2c_dev)
+{
+	int ret;
+
+	ret = stm32f4_i2c_set_periph_clk_freq(i2c_dev);
+	if (ret)
+		return ret;
+
+	stm32f4_i2c_set_rise_time(i2c_dev);
+
+	stm32f4_i2c_set_speed_mode(i2c_dev);
+
+	/* Enable I2C */
+	writel_relaxed(STM32F4_I2C_CR1_PE, i2c_dev->base + STM32F4_I2C_CR1);
+
+	return 0;
+}
+
+static int stm32f4_i2c_wait_free_bus(struct stm32f4_i2c_dev *i2c_dev)
+{
+	u32 status;
+	int ret;
+
+	ret = readl_relaxed_poll_timeout(i2c_dev->base + STM32F4_I2C_SR2,
+					 status,
+					 !(status & STM32F4_I2C_SR2_BUSY),
+					 10, 1000);
+	if (ret) {
+		dev_dbg(i2c_dev->dev, "bus not free\n");
+		ret = -EBUSY;
+	}
+
+	return ret;
+}
+
+/**
+ * stm32f4_i2c_write_ byte() - Write a byte in the data register
+ * @i2c_dev: Controller's private data
+ * @byte: Data to write in the register
+ */
+static void stm32f4_i2c_write_byte(struct stm32f4_i2c_dev *i2c_dev, u8 byte)
+{
+	writel_relaxed(byte, i2c_dev->base + STM32F4_I2C_DR);
+}
+
+/**
+ * stm32f4_i2c_write_msg() - Fill the data register in write mode
+ * @i2c_dev: Controller's private data
+ *
+ * This function fills the data register with I2C transfer buffer
+ */
+static void stm32f4_i2c_write_msg(struct stm32f4_i2c_dev *i2c_dev)
+{
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+
+	stm32f4_i2c_write_byte(i2c_dev, *msg->buf++);
+	msg->count--;
+}
+
+static void stm32f4_i2c_read_msg(struct stm32f4_i2c_dev *i2c_dev)
+{
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	u32 rbuf;
+
+	rbuf = readl_relaxed(i2c_dev->base + STM32F4_I2C_DR);
+	*msg->buf++ = rbuf;
+	msg->count--;
+}
+
+static void stm32f4_i2c_terminate_xfer(struct stm32f4_i2c_dev *i2c_dev)
+{
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
+
+	stm32f4_i2c_disable_irq(i2c_dev);
+
+	reg = i2c_dev->base + STM32F4_I2C_CR1;
+	if (msg->stop)
+		stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
+	else
+		stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
+
+	complete(&i2c_dev->complete);
+}
+
+/**
+ * stm32f4_i2c_handle_write() - Handle FIFO empty interrupt in case of write
+ * @i2c_dev: Controller's private data
+ */
+static void stm32f4_i2c_handle_write(struct stm32f4_i2c_dev *i2c_dev)
+{
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
+
+	if (msg->count) {
+		stm32f4_i2c_write_msg(i2c_dev);
+		if (!msg->count) {
+			/*
+			 * Disable buffer interrupts for RX not empty and TX
+			 * empty events
+			 */
+			stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
+		}
+	} else {
+		stm32f4_i2c_terminate_xfer(i2c_dev);
+	}
+}
+
+/**
+ * stm32f4_i2c_handle_read() - Handle FIFO empty interrupt in case of read
+ * @i2c_dev: Controller's private data
+ *
+ * This function is called when a new data is received in data register
+ */
+static void stm32f4_i2c_handle_read(struct stm32f4_i2c_dev *i2c_dev)
+{
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
+
+	switch (msg->count) {
+	case 1:
+		stm32f4_i2c_disable_irq(i2c_dev);
+		stm32f4_i2c_read_msg(i2c_dev);
+		complete(&i2c_dev->complete);
+		break;
+	/*
+	 * For 2-byte reception, 3-byte reception and for Data N-2, N-1 and N
+	 * for N-byte reception with N > 3, we do not have to read the data
+	 * register when RX not empty event occurs as we have to wait for byte
+	 * transferred finished event before reading data.
+	 * So, here we just disable buffer interrupt in order to avoid another
+	 * system preemption due to RX not empty event.
+	 */
+	case 2:
+	case 3:
+		stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
+		break;
+	/*
+	 * For N byte reception with N > 3 we directly read data register
+	 * until N-2 data.
+	 */
+	default:
+		stm32f4_i2c_read_msg(i2c_dev);
+	}
+}
+
+/**
+ * stm32f4_i2c_handle_rx_done() - Handle byte transfer finished interrupt
+ * in case of read
+ * @i2c_dev: Controller's private data
+ *
+ * This function is called when a new data is received in the shift register
+ * but data register has not been read yet.
+ */
+static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
+{
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	void __iomem *reg;
+	u32 mask;
+	int i;
+
+	switch (msg->count) {
+	case 2:
+		/*
+		 * In order to correctly send the Stop or Repeated Start
+		 * condition on the I2C bus, the STOP/START bit has to be set
+		 * before reading the last two bytes (data N-1 and N).
+		 * After that, we could read the last two bytes, disable
+		 * remaining interrupts and notify the end of xfer to the
+		 * client
+		 */
+		reg = i2c_dev->base + STM32F4_I2C_CR1;
+		if (msg->stop)
+			stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
+		else
+			stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
+
+		for (i = 2; i > 0; i--)
+			stm32f4_i2c_read_msg(i2c_dev);
+
+		reg = i2c_dev->base + STM32F4_I2C_CR2;
+		mask = STM32F4_I2C_CR2_ITEVTEN | STM32F4_I2C_CR2_ITERREN;
+		stm32f4_i2c_clr_bits(reg, mask);
+
+		complete(&i2c_dev->complete);
+		break;
+	case 3:
+		/*
+		 * In order to correctly generate the NACK pulse after the last
+		 * received data byte, we have to enable NACK before reading N-2
+		 * data
+		 */
+		reg = i2c_dev->base + STM32F4_I2C_CR1;
+		stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_ACK);
+		stm32f4_i2c_read_msg(i2c_dev);
+		break;
+	default:
+		stm32f4_i2c_read_msg(i2c_dev);
+	}
+}
+
+/**
+ * stm32f4_i2c_handle_rx_addr() - Handle address matched interrupt in case of
+ * master receiver
+ * @i2c_dev: Controller's private data
+ */
+static void stm32f4_i2c_handle_rx_addr(struct stm32f4_i2c_dev *i2c_dev)
+{
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	u32 cr1;
+
+	switch (msg->count) {
+	case 0:
+		stm32f4_i2c_terminate_xfer(i2c_dev);
+
+		/* Clear ADDR flag */
+		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
+		break;
+	case 1:
+		/*
+		 * Single byte reception:
+		 * Enable NACK and reset POS (Acknowledge position).
+		 * Then, clear ADDR flag and set STOP or RepSTART.
+		 * In that way, the NACK and STOP or RepStart pulses will be
+		 * sent as soon as the byte will be received in shift register
+		 */
+		cr1 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR1);
+		cr1 &= ~(STM32F4_I2C_CR1_ACK | STM32F4_I2C_CR1_POS);
+		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);
+
+		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
+
+		if (msg->stop)
+			cr1 |= STM32F4_I2C_CR1_STOP;
+		else
+			cr1 |= STM32F4_I2C_CR1_START;
+		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);
+		break;
+	case 2:
+		/*
+		 * 2-byte reception:
+		 * Enable NACK, set POS (NACK position) and clear ADDR flag.
+		 * In that way, NACK will be sent for the next byte which will
+		 * be received in the shift register instead of the current
+		 * one.
+		 */
+		cr1 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR1);
+		cr1 &= ~STM32F4_I2C_CR1_ACK;
+		cr1 |= STM32F4_I2C_CR1_POS;
+		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);
+
+		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
+		break;
+
+	default:
+		/*
+		 * N-byte reception:
+		 * Enable ACK, reset POS (ACK postion) and clear ADDR flag.
+		 * In that way, ACK will be sent as soon as the current byte
+		 * will be received in the shift register
+		 */
+		cr1 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR1);
+		cr1 |= STM32F4_I2C_CR1_ACK;
+		cr1 &= ~STM32F4_I2C_CR1_POS;
+		writel_relaxed(cr1, i2c_dev->base + STM32F4_I2C_CR1);
+
+		readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
+		break;
+	}
+}
+
+/**
+ * stm32f4_i2c_isr_event() - Interrupt routine for I2C bus event
+ * @irq: interrupt number
+ * @data: Controller's private data
+ */
+static irqreturn_t stm32f4_i2c_isr_event(int irq, void *data)
+{
+	struct stm32f4_i2c_dev *i2c_dev = data;
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	u32 possible_status = STM32F4_I2C_SR1_ITEVTEN_MASK;
+	u32 status, ien, event, cr2;
+
+	cr2 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR2);
+	ien = cr2 & STM32F4_I2C_CR2_IRQ_MASK;
+
+	/* Update possible_status if buffer interrupt is enabled */
+	if (ien & STM32F4_I2C_CR2_ITBUFEN)
+		possible_status |= STM32F4_I2C_SR1_ITBUFEN_MASK;
+
+	status = readl_relaxed(i2c_dev->base + STM32F4_I2C_SR1);
+	event = status & possible_status;
+	if (!event) {
+		dev_dbg(i2c_dev->dev,
+			"spurious evt irq (status=0x%08x, ien=0x%08x)\n",
+			status, ien);
+		return IRQ_NONE;
+	}
+
+	/* Start condition generated */
+	if (event & STM32F4_I2C_SR1_SB)
+		stm32f4_i2c_write_byte(i2c_dev, msg->addr);
+
+	/* I2C Address sent */
+	if (event & STM32F4_I2C_SR1_ADDR) {
+		if (msg->addr & I2C_M_RD)
+			stm32f4_i2c_handle_rx_addr(i2c_dev);
+		else
+			readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
+
+		/*
+		 * Enable buffer interrupts for RX not empty and TX empty
+		 * events
+		 */
+		cr2 |= STM32F4_I2C_CR2_ITBUFEN;
+		writel_relaxed(cr2, i2c_dev->base + STM32F4_I2C_CR2);
+	}
+
+	/* TX empty */
+	if ((event & STM32F4_I2C_SR1_TXE) && !(msg->addr & I2C_M_RD))
+		stm32f4_i2c_handle_write(i2c_dev);
+
+	/* RX not empty */
+	if ((event & STM32F4_I2C_SR1_RXNE) && (msg->addr & I2C_M_RD))
+		stm32f4_i2c_handle_read(i2c_dev);
+
+	/*
+	 * The BTF (Byte Transfer finished) event occurs when:
+	 * - in reception : a new byte is received in the shift register
+	 * but the previous byte has not been read yet from data register
+	 * - in transmission: a new byte should be sent but the data register
+	 * has not been written yet
+	 */
+	if (event & STM32F4_I2C_SR1_BTF) {
+		if (msg->addr & I2C_M_RD)
+			stm32f4_i2c_handle_rx_done(i2c_dev);
+		else
+			stm32f4_i2c_handle_write(i2c_dev);
+	}
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * stm32f4_i2c_isr_error() - Interrupt routine for I2C bus error
+ * @irq: interrupt number
+ * @data: Controller's private data
+ */
+static irqreturn_t stm32f4_i2c_isr_error(int irq, void *data)
+{
+	struct stm32f4_i2c_dev *i2c_dev = data;
+	struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
+	void __iomem *reg;
+	u32 status;
+
+	status = readl_relaxed(i2c_dev->base + STM32F4_I2C_SR1);
+
+	/* Arbitration lost */
+	if (status & STM32F4_I2C_SR1_ARLO) {
+		status &= ~STM32F4_I2C_SR1_ARLO;
+		writel_relaxed(status, i2c_dev->base + STM32F4_I2C_SR1);
+		msg->result = -EAGAIN;
+	}
+
+	/*
+	 * Acknowledge failure:
+	 * In master transmitter mode a Stop must be generated by software
+	 */
+	if (status & STM32F4_I2C_SR1_AF) {
+		if (!(msg->addr & I2C_M_RD)) {
+			reg = i2c_dev->base + STM32F4_I2C_CR1;
+			stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
+		}
+		status &= ~STM32F4_I2C_SR1_AF;
+		writel_relaxed(status, i2c_dev->base + STM32F4_I2C_SR1);
+		msg->result = -EIO;
+	}
+
+	/* Bus error */
+	if (status & STM32F4_I2C_SR1_BERR) {
+		status &= ~STM32F4_I2C_SR1_BERR;
+		writel_relaxed(status, i2c_dev->base + STM32F4_I2C_SR1);
+		msg->result = -EIO;
+	}
+
+	stm32f4_i2c_disable_irq(i2c_dev);
+	complete(&i2c_dev->complete);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * stm32f4_i2c_xfer_msg() - Transfer a single I2C message
+ * @i2c_dev: Controller's private data
+ * @msg: I2C message to transfer
+ * @is_first: first message of the sequence
+ * @is_last: last message of the sequence
+ */
+static int stm32f4_i2c_xfer_msg(struct stm32f4_i2c_dev *i2c_dev,
+				struct i2c_msg *msg, bool is_first,
+				bool is_last)
+{
+	struct stm32f4_i2c_msg *f4_msg = &i2c_dev->msg;
+	void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR1;
+	unsigned long timeout;
+	u32 mask;
+	int ret;
+
+	f4_msg->addr = i2c_8bit_addr_from_msg(msg);
+	f4_msg->buf = msg->buf;
+	f4_msg->count = msg->len;
+	f4_msg->result = 0;
+	f4_msg->stop = is_last;
+
+	reinit_completion(&i2c_dev->complete);
+
+	/* Enable events and errors interrupts */
+	mask = STM32F4_I2C_CR2_ITEVTEN | STM32F4_I2C_CR2_ITERREN;
+	stm32f4_i2c_set_bits(i2c_dev->base + STM32F4_I2C_CR2, mask);
+
+	if (is_first) {
+		ret = stm32f4_i2c_wait_free_bus(i2c_dev);
+		if (ret)
+			return ret;
+
+		/* START generation */
+		stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
+	}
+
+	timeout = wait_for_completion_timeout(&i2c_dev->complete,
+					      i2c_dev->adap.timeout);
+	ret = f4_msg->result;
+
+	if (!timeout)
+		ret = -ETIMEDOUT;
+
+	return ret;
+}
+
+/**
+ * stm32f4_i2c_xfer() - Transfer combined I2C message
+ * @i2c_adap: Adapter pointer to the controller
+ * @msgs: Pointer to data to be written.
+ * @num: Number of messages to be executed
+ */
+static int stm32f4_i2c_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg msgs[],
+			    int num)
+{
+	struct stm32f4_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
+	int ret, i;
+
+	ret = clk_enable(i2c_dev->clk);
+	if (ret) {
+		dev_err(i2c_dev->dev, "Failed to enable clock\n");
+		return ret;
+	}
+
+	for (i = 0; i < num && !ret; i++)
+		ret = stm32f4_i2c_xfer_msg(i2c_dev, &msgs[i], i == 0,
+					   i == num - 1);
+
+	clk_disable(i2c_dev->clk);
+
+	return (ret < 0) ? ret : num;
+}
+
+static u32 stm32f4_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static struct i2c_algorithm stm32f4_i2c_algo = {
+	.master_xfer = stm32f4_i2c_xfer,
+	.functionality = stm32f4_i2c_func,
+};
+
+static int stm32f4_i2c_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct stm32f4_i2c_dev *i2c_dev;
+	struct resource *res;
+	u32 irq_event, irq_error, clk_rate;
+	struct i2c_adapter *adap;
+	struct reset_control *rst;
+	int ret;
+
+	i2c_dev = devm_kzalloc(&pdev->dev, sizeof(*i2c_dev), GFP_KERNEL);
+	if (!i2c_dev)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	i2c_dev->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(i2c_dev->base))
+		return PTR_ERR(i2c_dev->base);
+
+	irq_event = irq_of_parse_and_map(np, 0);
+	if (!irq_event) {
+		dev_err(&pdev->dev, "IRQ event missing or invalid\n");
+		return -EINVAL;
+	}
+
+	irq_error = irq_of_parse_and_map(np, 1);
+	if (!irq_error) {
+		dev_err(&pdev->dev, "IRQ error missing or invalid\n");
+		return -EINVAL;
+	}
+
+	i2c_dev->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(i2c_dev->clk)) {
+		dev_err(&pdev->dev, "Error: Missing controller clock\n");
+		return PTR_ERR(i2c_dev->clk);
+	}
+	ret = clk_prepare_enable(i2c_dev->clk);
+	if (ret) {
+		dev_err(i2c_dev->dev, "Failed to prepare_enable clock\n");
+		return ret;
+	}
+
+	rst = devm_reset_control_get(&pdev->dev, NULL);
+	if (IS_ERR(rst)) {
+		dev_err(&pdev->dev, "Error: Missing controller reset\n");
+		ret = PTR_ERR(rst);
+		goto clk_free;
+	}
+	reset_control_assert(rst);
+	udelay(2);
+	reset_control_deassert(rst);
+
+	i2c_dev->speed = STM32F4_I2C_SPEED_STANDARD;
+	ret = of_property_read_u32(np, "clock-frequency", &clk_rate);
+	if (!ret && clk_rate >= 400000)
+		i2c_dev->speed = STM32F4_I2C_SPEED_FAST;
+
+	i2c_dev->dev = &pdev->dev;
+
+	ret = devm_request_irq(&pdev->dev, irq_event, stm32f4_i2c_isr_event, 0,
+			       pdev->name, i2c_dev);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to request irq event %i\n",
+			irq_event);
+		goto clk_free;
+	}
+
+	ret = devm_request_irq(&pdev->dev, irq_error, stm32f4_i2c_isr_error, 0,
+			       pdev->name, i2c_dev);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to request irq error %i\n",
+			irq_error);
+		goto clk_free;
+	}
+
+	ret = stm32f4_i2c_hw_config(i2c_dev);
+	if (ret)
+		goto clk_free;
+
+	adap = &i2c_dev->adap;
+	i2c_set_adapdata(adap, i2c_dev);
+	snprintf(adap->name, sizeof(adap->name), "STM32 I2C(%pa)", &res->start);
+	adap->owner = THIS_MODULE;
+	adap->timeout = 2 * HZ;
+	adap->retries = 0;
+	adap->algo = &stm32f4_i2c_algo;
+	adap->dev.parent = &pdev->dev;
+	adap->dev.of_node = pdev->dev.of_node;
+
+	init_completion(&i2c_dev->complete);
+
+	ret = i2c_add_adapter(adap);
+	if (ret)
+		goto clk_free;
+
+	platform_set_drvdata(pdev, i2c_dev);
+
+	clk_disable(i2c_dev->clk);
+
+	dev_info(i2c_dev->dev, "STM32F4 I2C driver registered\n");
+
+	return 0;
+
+clk_free:
+	clk_disable_unprepare(i2c_dev->clk);
+	return ret;
+}
+
+static int stm32f4_i2c_remove(struct platform_device *pdev)
+{
+	struct stm32f4_i2c_dev *i2c_dev = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&i2c_dev->adap);
+
+	clk_unprepare(i2c_dev->clk);
+
+	return 0;
+}
+
+static const struct of_device_id stm32f4_i2c_match[] = {
+	{ .compatible = "st,stm32f4-i2c", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, stm32f4_i2c_match);
+
+static struct platform_driver stm32f4_i2c_driver = {
+	.driver = {
+		.name = "stm32f4-i2c",
+		.of_match_table = stm32f4_i2c_match,
+	},
+	.probe = stm32f4_i2c_probe,
+	.remove = stm32f4_i2c_remove,
+};
+
+module_platform_driver(stm32f4_i2c_driver);
+
+MODULE_AUTHOR("M'boumba Cedric Madianga <cedric.madianga@gmail.com>");
+MODULE_DESCRIPTION("STMicroelectronics STM32F4 I2C driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/i2c/busses/i2c-tegra-bpmp.c b/drivers/i2c/busses/i2c-tegra-bpmp.c
new file mode 100644
index 0000000..9eed69d
--- /dev/null
+++ b/drivers/i2c/busses/i2c-tegra-bpmp.c
@@ -0,0 +1,346 @@
+/*
+ * drivers/i2c/busses/i2c-tegra-bpmp.c
+ *
+ * Copyright (c) 2016 NVIDIA Corporation.  All rights reserved.
+ *
+ * Author: Shardar Shariff Md <smohammed@nvidia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#include <soc/tegra/bpmp-abi.h>
+#include <soc/tegra/bpmp.h>
+
+/*
+ * Serialized I2C message header size is 6 bytes and includes address, flags
+ * and length
+ */
+#define SERIALI2C_HDR_SIZE 6
+
+struct tegra_bpmp_i2c {
+	struct i2c_adapter adapter;
+	struct device *dev;
+
+	struct tegra_bpmp *bpmp;
+	unsigned int bus;
+};
+
+/*
+ * Linux flags are translated to BPMP defined I2C flags that are used in BPMP
+ * firmware I2C driver to avoid any issues in future if Linux I2C flags are
+ * changed.
+ */
+static int tegra_bpmp_xlate_flags(u16 flags, u16 *out)
+{
+	if (flags & I2C_M_TEN) {
+		*out |= SERIALI2C_TEN;
+		flags &= ~I2C_M_TEN;
+	}
+
+	if (flags & I2C_M_RD) {
+		*out |= SERIALI2C_RD;
+		flags &= ~I2C_M_RD;
+	}
+
+	if (flags & I2C_M_STOP) {
+		*out |= SERIALI2C_STOP;
+		flags &= ~I2C_M_STOP;
+	}
+
+	if (flags & I2C_M_NOSTART) {
+		*out |= SERIALI2C_NOSTART;
+		flags &= ~I2C_M_NOSTART;
+	}
+
+	if (flags & I2C_M_REV_DIR_ADDR) {
+		*out |= SERIALI2C_REV_DIR_ADDR;
+		flags &= ~I2C_M_REV_DIR_ADDR;
+	}
+
+	if (flags & I2C_M_IGNORE_NAK) {
+		*out |= SERIALI2C_IGNORE_NAK;
+		flags &= ~I2C_M_IGNORE_NAK;
+	}
+
+	if (flags & I2C_M_NO_RD_ACK) {
+		*out |= SERIALI2C_NO_RD_ACK;
+		flags &= ~I2C_M_NO_RD_ACK;
+	}
+
+	if (flags & I2C_M_RECV_LEN) {
+		*out |= SERIALI2C_RECV_LEN;
+		flags &= ~I2C_M_RECV_LEN;
+	}
+
+	return (flags != 0) ? -EINVAL : 0;
+}
+
+/**
+ * The serialized I2C format is simply the following:
+ * [addr little-endian][flags little-endian][len little-endian][data if write]
+ * [addr little-endian][flags little-endian][len little-endian][data if write]
+ *  ...
+ *
+ * The flags are translated from Linux kernel representation to seriali2c
+ * representation. Any undefined flag being set causes an error.
+ *
+ * The data is there only for writes. Reads have the data transferred in the
+ * other direction, and thus data is not present.
+ *
+ * See deserialize_i2c documentation for the data format in the other direction.
+ */
+static int tegra_bpmp_serialize_i2c_msg(struct tegra_bpmp_i2c *i2c,
+					struct mrq_i2c_request *request,
+					struct i2c_msg *msgs,
+					unsigned int num)
+{
+	char *buf = request->xfer.data_buf;
+	unsigned int i, j, pos = 0;
+	int err;
+
+	for (i = 0; i < num; i++) {
+		struct i2c_msg *msg = &msgs[i];
+		u16 flags = 0;
+
+		err = tegra_bpmp_xlate_flags(msg->flags, &flags);
+		if (err < 0)
+			return err;
+
+		buf[pos++] = msg->addr & 0xff;
+		buf[pos++] = (msg->addr & 0xff00) >> 8;
+		buf[pos++] = flags & 0xff;
+		buf[pos++] = (flags & 0xff00) >> 8;
+		buf[pos++] = msg->len & 0xff;
+		buf[pos++] = (msg->len & 0xff00) >> 8;
+
+		if ((flags & SERIALI2C_RD) == 0) {
+			for (j = 0; j < msg->len; j++)
+				buf[pos++] = msg->buf[j];
+		}
+	}
+
+	request->xfer.data_size = pos;
+
+	return 0;
+}
+
+/**
+ * The data in the BPMP -> CPU direction is composed of sequential blocks for
+ * those messages that have I2C_M_RD. So, for example, if you have:
+ *
+ * - !I2C_M_RD, len == 5, data == a0 01 02 03 04
+ * - !I2C_M_RD, len == 1, data == a0
+ * - I2C_M_RD, len == 2, data == [uninitialized buffer 1]
+ * - !I2C_M_RD, len == 1, data == a2
+ * - I2C_M_RD, len == 2, data == [uninitialized buffer 2]
+ *
+ * ...then the data in the BPMP -> CPU direction would be 4 bytes total, and
+ * would contain 2 bytes that will go to uninitialized buffer 1, and 2 bytes
+ * that will go to uninitialized buffer 2.
+ */
+static int tegra_bpmp_i2c_deserialize(struct tegra_bpmp_i2c *i2c,
+				      struct mrq_i2c_response *response,
+				      struct i2c_msg *msgs,
+				      unsigned int num)
+{
+	size_t size = response->xfer.data_size, len = 0, pos = 0;
+	char *buf = response->xfer.data_buf;
+	unsigned int i;
+
+	for (i = 0; i < num; i++)
+		if (msgs[i].flags & I2C_M_RD)
+			len += msgs[i].len;
+
+	if (len != size)
+		return -EINVAL;
+
+	for (i = 0; i < num; i++) {
+		if (msgs[i].flags & I2C_M_RD) {
+			memcpy(msgs[i].buf, buf + pos, msgs[i].len);
+			pos += msgs[i].len;
+		}
+	}
+
+	return 0;
+}
+
+static int tegra_bpmp_i2c_msg_len_check(struct i2c_msg *msgs, unsigned int num)
+{
+	size_t tx_len = 0, rx_len = 0;
+	unsigned int i;
+
+	for (i = 0; i < num; i++)
+		if (!(msgs[i].flags & I2C_M_RD))
+			tx_len += SERIALI2C_HDR_SIZE + msgs[i].len;
+
+	if (tx_len > TEGRA_I2C_IPC_MAX_IN_BUF_SIZE)
+		return -EINVAL;
+
+	for (i = 0; i < num; i++)
+		if ((msgs[i].flags & I2C_M_RD))
+			rx_len += msgs[i].len;
+
+	if (rx_len > TEGRA_I2C_IPC_MAX_OUT_BUF_SIZE)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int tegra_bpmp_i2c_msg_xfer(struct tegra_bpmp_i2c *i2c,
+				   struct mrq_i2c_request *request,
+				   struct mrq_i2c_response *response)
+{
+	struct tegra_bpmp_message msg;
+	int err;
+
+	request->cmd = CMD_I2C_XFER;
+	request->xfer.bus_id = i2c->bus;
+
+	memset(&msg, 0, sizeof(msg));
+	msg.mrq = MRQ_I2C;
+	msg.tx.data = request;
+	msg.tx.size = sizeof(*request);
+	msg.rx.data = response;
+	msg.rx.size = sizeof(*response);
+
+	if (irqs_disabled())
+		err = tegra_bpmp_transfer_atomic(i2c->bpmp, &msg);
+	else
+		err = tegra_bpmp_transfer(i2c->bpmp, &msg);
+
+	return err;
+}
+
+static int tegra_bpmp_i2c_xfer(struct i2c_adapter *adapter,
+			       struct i2c_msg *msgs, int num)
+{
+	struct tegra_bpmp_i2c *i2c = i2c_get_adapdata(adapter);
+	struct mrq_i2c_response response;
+	struct mrq_i2c_request request;
+	int err;
+
+	err = tegra_bpmp_i2c_msg_len_check(msgs, num);
+	if (err < 0) {
+		dev_err(i2c->dev, "unsupported message length\n");
+		return err;
+	}
+
+	memset(&request, 0, sizeof(request));
+	memset(&response, 0, sizeof(response));
+
+	err = tegra_bpmp_serialize_i2c_msg(i2c, &request, msgs, num);
+	if (err < 0) {
+		dev_err(i2c->dev, "failed to serialize message: %d\n", err);
+		return err;
+	}
+
+	err = tegra_bpmp_i2c_msg_xfer(i2c, &request, &response);
+	if (err < 0) {
+		dev_err(i2c->dev, "failed to transfer message: %d\n", err);
+		return err;
+	}
+
+	err = tegra_bpmp_i2c_deserialize(i2c, &response, msgs, num);
+	if (err < 0) {
+		dev_err(i2c->dev, "failed to deserialize message: %d\n", err);
+		return err;
+	}
+
+	return num;
+}
+
+static u32 tegra_bpmp_i2c_func(struct i2c_adapter *adapter)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_10BIT_ADDR |
+	       I2C_FUNC_PROTOCOL_MANGLING | I2C_FUNC_NOSTART;
+}
+
+static const struct i2c_algorithm tegra_bpmp_i2c_algo = {
+	.master_xfer = tegra_bpmp_i2c_xfer,
+	.functionality = tegra_bpmp_i2c_func,
+};
+
+static int tegra_bpmp_i2c_probe(struct platform_device *pdev)
+{
+	struct tegra_bpmp_i2c *i2c;
+	u32 value;
+	int err;
+
+	i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL);
+	if (!i2c)
+		return -ENOMEM;
+
+	i2c->dev = &pdev->dev;
+
+	i2c->bpmp = dev_get_drvdata(pdev->dev.parent);
+	if (!i2c->bpmp)
+		return -ENODEV;
+
+	err = of_property_read_u32(pdev->dev.of_node, "nvidia,bpmp-bus-id",
+				   &value);
+	if (err < 0)
+		return err;
+
+	i2c->bus = value;
+
+	i2c_set_adapdata(&i2c->adapter, i2c);
+	i2c->adapter.owner = THIS_MODULE;
+	strlcpy(i2c->adapter.name, "Tegra BPMP I2C adapter",
+		sizeof(i2c->adapter.name));
+	i2c->adapter.algo = &tegra_bpmp_i2c_algo;
+	i2c->adapter.dev.parent = &pdev->dev;
+	i2c->adapter.dev.of_node = pdev->dev.of_node;
+
+	platform_set_drvdata(pdev, i2c);
+
+	return i2c_add_adapter(&i2c->adapter);
+}
+
+static int tegra_bpmp_i2c_remove(struct platform_device *pdev)
+{
+	struct tegra_bpmp_i2c *i2c = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&i2c->adapter);
+
+	return 0;
+}
+
+static const struct of_device_id tegra_bpmp_i2c_of_match[] = {
+	{ .compatible = "nvidia,tegra186-bpmp-i2c", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, tegra_bpmp_i2c_of_match);
+
+static struct platform_driver tegra_bpmp_i2c_driver = {
+	.driver = {
+		.name = "tegra-bpmp-i2c",
+		.of_match_table = tegra_bpmp_i2c_of_match,
+	},
+	.probe = tegra_bpmp_i2c_probe,
+	.remove = tegra_bpmp_i2c_remove,
+};
+module_platform_driver(tegra_bpmp_i2c_driver);
+
+MODULE_DESCRIPTION("NVIDIA Tegra BPMP I2C bus contoller driver");
+MODULE_AUTHOR("Shardar Shariff Md <smohammed@nvidia.com>");
+MODULE_AUTHOR("Juha-Matti Tilli");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/i2c/busses/i2c-thunderx-pcidrv.c b/drivers/i2c/busses/i2c-thunderx-pcidrv.c
index bba5b42..1d4c2be 100644
--- a/drivers/i2c/busses/i2c-thunderx-pcidrv.c
+++ b/drivers/i2c/busses/i2c-thunderx-pcidrv.c
@@ -188,11 +188,11 @@ static int thunder_i2c_probe_pci(struct pci_dev *pdev,
 	i2c->hlc_int_enable = thunder_i2c_hlc_int_enable;
 	i2c->hlc_int_disable = thunder_i2c_hlc_int_disable;
 
-	ret = pci_enable_msix(pdev, &i2c->i2c_msix, 1);
-	if (ret)
+	ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_MSIX);
+	if (ret < 0)
 		goto error;
 
-	ret = devm_request_irq(dev, i2c->i2c_msix.vector, octeon_i2c_isr, 0,
+	ret = devm_request_irq(dev, pci_irq_vector(pdev, 0), octeon_i2c_isr, 0,
 			       DRV_NAME, i2c);
 	if (ret)
 		goto error;
diff --git a/drivers/i2c/busses/i2c-xgene-slimpro.c b/drivers/i2c/busses/i2c-xgene-slimpro.c
index 0ab1e55..dbe7e44 100644
--- a/drivers/i2c/busses/i2c-xgene-slimpro.c
+++ b/drivers/i2c/busses/i2c-xgene-slimpro.c
@@ -372,7 +372,7 @@ static u32 xgene_slimpro_i2c_func(struct i2c_adapter *adapter)
 		I2C_FUNC_SMBUS_I2C_BLOCK;
 }
 
-static struct i2c_algorithm xgene_slimpro_i2c_algorithm = {
+static const struct i2c_algorithm xgene_slimpro_i2c_algorithm = {
 	.smbus_xfer = xgene_slimpro_i2c_xfer,
 	.functionality = xgene_slimpro_i2c_func,
 };
diff --git a/drivers/i2c/busses/i2c-xlp9xx.c b/drivers/i2c/busses/i2c-xlp9xx.c
index 84a8b2e..66b464d 100644
--- a/drivers/i2c/busses/i2c-xlp9xx.c
+++ b/drivers/i2c/busses/i2c-xlp9xx.c
@@ -334,7 +334,7 @@ static u32 xlp9xx_i2c_functionality(struct i2c_adapter *adapter)
 		I2C_FUNC_10BIT_ADDR;
 }
 
-static struct i2c_algorithm xlp9xx_i2c_algo = {
+static const struct i2c_algorithm xlp9xx_i2c_algo = {
 	.master_xfer = xlp9xx_i2c_xfer,
 	.functionality = xlp9xx_i2c_functionality,
 };
diff --git a/drivers/i2c/busses/i2c-xlr.c b/drivers/i2c/busses/i2c-xlr.c
index ad17d88..484bfa15d 100644
--- a/drivers/i2c/busses/i2c-xlr.c
+++ b/drivers/i2c/busses/i2c-xlr.c
@@ -335,7 +335,7 @@ static u32 xlr_func(struct i2c_adapter *adap)
 	return (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) | I2C_FUNC_I2C;
 }
 
-static struct i2c_algorithm xlr_i2c_algo = {
+static const struct i2c_algorithm xlr_i2c_algo = {
 	.master_xfer	= xlr_i2c_xfer,
 	.functionality	= xlr_func,
 };
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index bfb6ba7..d2402bb 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -3705,6 +3705,39 @@ int i2c_slave_unregister(struct i2c_client *client)
 	return ret;
 }
 EXPORT_SYMBOL_GPL(i2c_slave_unregister);
+
+/**
+ * i2c_detect_slave_mode - detect operation mode
+ * @dev: The device owning the bus
+ *
+ * This checks the device nodes for an I2C slave by checking the address
+ * used in the reg property. If the address match the I2C_OWN_SLAVE_ADDRESS
+ * flag this means the device is configured to act as a I2C slave and it will
+ * be listening at that address.
+ *
+ * Returns true if an I2C own slave address is detected, otherwise returns
+ * false.
+ */
+bool i2c_detect_slave_mode(struct device *dev)
+{
+	if (IS_BUILTIN(CONFIG_OF) && dev->of_node) {
+		struct device_node *child;
+		u32 reg;
+
+		for_each_child_of_node(dev->of_node, child) {
+			of_property_read_u32(child, "reg", &reg);
+			if (reg & I2C_OWN_SLAVE_ADDRESS) {
+				of_node_put(child);
+				return true;
+			}
+		}
+	} else if (IS_BUILTIN(CONFIG_ACPI) && ACPI_HANDLE(dev)) {
+		dev_dbg(dev, "ACPI slave is not supported yet\n");
+	}
+	return false;
+}
+EXPORT_SYMBOL_GPL(i2c_detect_slave_mode);
+
 #endif
 
 MODULE_AUTHOR("Simon G. Vogl <simon@tk.uni-linz.ac.at>");
diff --git a/drivers/i2c/muxes/i2c-mux-mlxcpld.c b/drivers/i2c/muxes/i2c-mux-mlxcpld.c
index b7ca249..e53f2ab 100644
--- a/drivers/i2c/muxes/i2c-mux-mlxcpld.c
+++ b/drivers/i2c/muxes/i2c-mux-mlxcpld.c
@@ -40,7 +40,6 @@
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/version.h>
 #include <linux/i2c/mlxcpld.h>
 
 #define CPLD_MUX_MAX_NCHANS	8
diff --git a/drivers/i2c/muxes/i2c-mux-pca9541.c b/drivers/i2c/muxes/i2c-mux-pca9541.c
index 4ea7e69..77840f7 100644
--- a/drivers/i2c/muxes/i2c-mux-pca9541.c
+++ b/drivers/i2c/muxes/i2c-mux-pca9541.c
@@ -90,6 +90,7 @@ static const struct of_device_id pca9541_of_match[] = {
 	{ .compatible = "nxp,pca9541" },
 	{}
 };
+MODULE_DEVICE_TABLE(of, pca9541_of_match);
 #endif
 
 /*
diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c
index dd18b9c..dfc1c0e 100644
--- a/drivers/i2c/muxes/i2c-mux-pca954x.c
+++ b/drivers/i2c/muxes/i2c-mux-pca954x.c
@@ -41,14 +41,20 @@
 #include <linux/i2c.h>
 #include <linux/i2c-mux.h>
 #include <linux/i2c/pca954x.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_device.h>
+#include <linux/of_irq.h>
 #include <linux/pm.h>
 #include <linux/slab.h>
+#include <linux/spinlock.h>
 
 #define PCA954X_MAX_NCHANS 8
 
+#define PCA954X_IRQ_OFFSET 4
+
 enum pca_type {
 	pca_9540,
 	pca_9542,
@@ -63,6 +69,7 @@ enum pca_type {
 struct chip_desc {
 	u8 nchans;
 	u8 enable;	/* used for muxes only */
+	u8 has_irq;
 	enum muxtype {
 		pca954x_ismux = 0,
 		pca954x_isswi
@@ -75,6 +82,10 @@ struct pca954x {
 	u8 last_chan;		/* last register value */
 	u8 deselect;
 	struct i2c_client *client;
+
+	struct irq_domain *irq;
+	unsigned int irq_mask;
+	spinlock_t lock;
 };
 
 /* Provide specs for the PCA954x types we know about */
@@ -84,17 +95,26 @@ static const struct chip_desc chips[] = {
 		.enable = 0x4,
 		.muxtype = pca954x_ismux,
 	},
+	[pca_9542] = {
+		.nchans = 2,
+		.enable = 0x4,
+		.has_irq = 1,
+		.muxtype = pca954x_ismux,
+	},
 	[pca_9543] = {
 		.nchans = 2,
+		.has_irq = 1,
 		.muxtype = pca954x_isswi,
 	},
 	[pca_9544] = {
 		.nchans = 4,
 		.enable = 0x4,
+		.has_irq = 1,
 		.muxtype = pca954x_ismux,
 	},
 	[pca_9545] = {
 		.nchans = 4,
+		.has_irq = 1,
 		.muxtype = pca954x_isswi,
 	},
 	[pca_9547] = {
@@ -110,7 +130,7 @@ static const struct chip_desc chips[] = {
 
 static const struct i2c_device_id pca954x_id[] = {
 	{ "pca9540", pca_9540 },
-	{ "pca9542", pca_9540 },
+	{ "pca9542", pca_9542 },
 	{ "pca9543", pca_9543 },
 	{ "pca9544", pca_9544 },
 	{ "pca9545", pca_9545 },
@@ -124,7 +144,7 @@ MODULE_DEVICE_TABLE(i2c, pca954x_id);
 #ifdef CONFIG_ACPI
 static const struct acpi_device_id pca954x_acpi_ids[] = {
 	{ .id = "PCA9540", .driver_data = pca_9540 },
-	{ .id = "PCA9542", .driver_data = pca_9540 },
+	{ .id = "PCA9542", .driver_data = pca_9542 },
 	{ .id = "PCA9543", .driver_data = pca_9543 },
 	{ .id = "PCA9544", .driver_data = pca_9544 },
 	{ .id = "PCA9545", .driver_data = pca_9545 },
@@ -148,6 +168,7 @@ static const struct of_device_id pca954x_of_match[] = {
 	{ .compatible = "nxp,pca9548", .data = &chips[pca_9548] },
 	{}
 };
+MODULE_DEVICE_TABLE(of, pca954x_of_match);
 #endif
 
 /* Write to mux register. Don't use i2c_transfer()/i2c_smbus_xfer()
@@ -217,6 +238,114 @@ static int pca954x_deselect_mux(struct i2c_mux_core *muxc, u32 chan)
 	return pca954x_reg_write(muxc->parent, client, data->last_chan);
 }
 
+static irqreturn_t pca954x_irq_handler(int irq, void *dev_id)
+{
+	struct pca954x *data = dev_id;
+	unsigned int child_irq;
+	int ret, i, handled = 0;
+
+	ret = i2c_smbus_read_byte(data->client);
+	if (ret < 0)
+		return IRQ_NONE;
+
+	for (i = 0; i < data->chip->nchans; i++) {
+		if (ret & BIT(PCA954X_IRQ_OFFSET + i)) {
+			child_irq = irq_linear_revmap(data->irq, i);
+			handle_nested_irq(child_irq);
+			handled++;
+		}
+	}
+	return handled ? IRQ_HANDLED : IRQ_NONE;
+}
+
+static void pca954x_irq_mask(struct irq_data *idata)
+{
+	struct pca954x *data = irq_data_get_irq_chip_data(idata);
+	unsigned int pos = idata->hwirq;
+	unsigned long flags;
+
+	spin_lock_irqsave(&data->lock, flags);
+
+	data->irq_mask &= ~BIT(pos);
+	if (!data->irq_mask)
+		disable_irq(data->client->irq);
+
+	spin_unlock_irqrestore(&data->lock, flags);
+}
+
+static void pca954x_irq_unmask(struct irq_data *idata)
+{
+	struct pca954x *data = irq_data_get_irq_chip_data(idata);
+	unsigned int pos = idata->hwirq;
+	unsigned long flags;
+
+	spin_lock_irqsave(&data->lock, flags);
+
+	if (!data->irq_mask)
+		enable_irq(data->client->irq);
+	data->irq_mask |= BIT(pos);
+
+	spin_unlock_irqrestore(&data->lock, flags);
+}
+
+static int pca954x_irq_set_type(struct irq_data *idata, unsigned int type)
+{
+	if ((type & IRQ_TYPE_SENSE_MASK) != IRQ_TYPE_LEVEL_LOW)
+		return -EINVAL;
+	return 0;
+}
+
+static struct irq_chip pca954x_irq_chip = {
+	.name = "i2c-mux-pca954x",
+	.irq_mask = pca954x_irq_mask,
+	.irq_unmask = pca954x_irq_unmask,
+	.irq_set_type = pca954x_irq_set_type,
+};
+
+static int pca954x_irq_setup(struct i2c_mux_core *muxc)
+{
+	struct pca954x *data = i2c_mux_priv(muxc);
+	struct i2c_client *client = data->client;
+	int c, err, irq;
+
+	if (!data->chip->has_irq || client->irq <= 0)
+		return 0;
+
+	spin_lock_init(&data->lock);
+
+	data->irq = irq_domain_add_linear(client->dev.of_node,
+					  data->chip->nchans,
+					  &irq_domain_simple_ops, data);
+	if (!data->irq)
+		return -ENODEV;
+
+	for (c = 0; c < data->chip->nchans; c++) {
+		irq = irq_create_mapping(data->irq, c);
+		irq_set_chip_data(irq, data);
+		irq_set_chip_and_handler(irq, &pca954x_irq_chip,
+			handle_simple_irq);
+	}
+
+	err = devm_request_threaded_irq(&client->dev, data->client->irq, NULL,
+					pca954x_irq_handler,
+					IRQF_ONESHOT | IRQF_SHARED,
+					"pca954x", data);
+	if (err)
+		goto err_req_irq;
+
+	disable_irq(data->client->irq);
+
+	return 0;
+err_req_irq:
+	for (c = 0; c < data->chip->nchans; c++) {
+		irq = irq_find_mapping(data->irq, c);
+		irq_dispose_mapping(irq);
+	}
+	irq_domain_remove(data->irq);
+
+	return err;
+}
+
 /*
  * I2C init/probing/exit functions
  */
@@ -281,6 +410,10 @@ static int pca954x_probe(struct i2c_client *client,
 	idle_disconnect_dt = of_node &&
 		of_property_read_bool(of_node, "i2c-mux-idle-disconnect");
 
+	ret = pca954x_irq_setup(muxc);
+	if (ret)
+		goto fail_del_adapters;
+
 	/* Now create an adapter for each channel */
 	for (num = 0; num < data->chip->nchans; num++) {
 		bool idle_disconnect_pd = false;
@@ -306,7 +439,7 @@ static int pca954x_probe(struct i2c_client *client,
 			dev_err(&client->dev,
 				"failed to register multiplexed adapter"
 				" %d as bus %d\n", num, force);
-			goto virt_reg_failed;
+			goto fail_del_adapters;
 		}
 	}
 
@@ -317,7 +450,7 @@ static int pca954x_probe(struct i2c_client *client,
 
 	return 0;
 
-virt_reg_failed:
+fail_del_adapters:
 	i2c_mux_del_adapters(muxc);
 	return ret;
 }
@@ -325,6 +458,16 @@ virt_reg_failed:
 static int pca954x_remove(struct i2c_client *client)
 {
 	struct i2c_mux_core *muxc = i2c_get_clientdata(client);
+	struct pca954x *data = i2c_mux_priv(muxc);
+	int c, irq;
+
+	if (data->irq) {
+		for (c = 0; c < data->chip->nchans; c++) {
+			irq = irq_find_mapping(data->irq, c);
+			irq_dispose_mapping(irq);
+		}
+		irq_domain_remove(data->irq);
+	}
 
 	i2c_mux_del_adapters(muxc);
 	return 0;