Merge branch 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata fixes from Tejun Heo:
 "Rather big for fixes pull.

   - SCC controllers never lived to see the light of the day.  Both
     libata and ide drivers removed.

   - In some configurations, link power management policy changes
     sometimes cause delayed spurious PHY events which can develop into
     noticeable failures.  This has been reported several times over the
     years.  Gabriele's patches suppress PHY events for a while after
     LPM policy changes which should help most of these failures without
     causing too much problem for hotplug use cases.

   - A few controller specific fixes"

[ Hmm.  I don't think removing SSC support is really a "fix", but hey, it
  removes a lot of lines of code.  Which I like.  So ...  good riddance ]

* 'for-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: avoton port-disable reset-quirk
  ata: select DW_DMAC in case of SATA_DWC
  libata: Blacklist queued TRIM on all Samsung 800-series
  libata: Ignore spurious PHY event on LPM policy change
  libata: Add helper to determine when PHY events should be ignored
  ata: ahci_st: fixup layering violations / drvdata errors
  Remove celleb-only SCC PATA drivers

8 files changed, 157 insertions, 1156 deletions

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index 5f60155..9dca4b9 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -270,6 +270,7 @@ config ATA_PIIX
 config SATA_DWC
 	tristate "DesignWare Cores SATA support"
 	depends on 460EX
+	select DW_DMAC
 	help
 	  This option enables support for the on-chip SATA controller of the
 	  AppliedMicro processor 460EX.
@@ -729,15 +730,6 @@ config PATA_SC1200
 
 	  If unsure, say N.
 
-config PATA_SCC
-	tristate "Toshiba's Cell Reference Set IDE support"
-	depends on PCI && PPC_CELLEB
-	help
-	  This option enables support for the built-in IDE controller on
-	  Toshiba Cell Reference Board.
-
-	  If unsure, say N.
-
 config PATA_SCH
 	tristate "Intel SCH PATA support"
 	depends on PCI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index b67e995..40f7865 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -75,7 +75,6 @@ obj-$(CONFIG_PATA_PDC_OLD)	+= pata_pdc202xx_old.o
 obj-$(CONFIG_PATA_RADISYS)	+= pata_radisys.o
 obj-$(CONFIG_PATA_RDC)		+= pata_rdc.o
 obj-$(CONFIG_PATA_SC1200)	+= pata_sc1200.o
-obj-$(CONFIG_PATA_SCC)		+= pata_scc.o
 obj-$(CONFIG_PATA_SCH)		+= pata_sch.o
 obj-$(CONFIG_PATA_SERVERWORKS)	+= pata_serverworks.o
 obj-$(CONFIG_PATA_SIL680)	+= pata_sil680.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index c7a92a7..65ee944 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -66,6 +66,7 @@ enum board_ids {
 	board_ahci_yes_fbs,
 
 	/* board IDs for specific chipsets in alphabetical order */
+	board_ahci_avn,
 	board_ahci_mcp65,
 	board_ahci_mcp77,
 	board_ahci_mcp89,
@@ -84,6 +85,8 @@ enum board_ids {
 static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
 static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
 				 unsigned long deadline);
+static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class,
+			      unsigned long deadline);
 static void ahci_mcp89_apple_enable(struct pci_dev *pdev);
 static bool is_mcp89_apple(struct pci_dev *pdev);
 static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
@@ -107,6 +110,11 @@ static struct ata_port_operations ahci_p5wdh_ops = {
 	.hardreset		= ahci_p5wdh_hardreset,
 };
 
+static struct ata_port_operations ahci_avn_ops = {
+	.inherits		= &ahci_ops,
+	.hardreset		= ahci_avn_hardreset,
+};
+
 static const struct ata_port_info ahci_port_info[] = {
 	/* by features */
 	[board_ahci] = {
@@ -151,6 +159,12 @@ static const struct ata_port_info ahci_port_info[] = {
 		.port_ops	= &ahci_ops,
 	},
 	/* by chipsets */
+	[board_ahci_avn] = {
+		.flags		= AHCI_FLAG_COMMON,
+		.pio_mask	= ATA_PIO4,
+		.udma_mask	= ATA_UDMA6,
+		.port_ops	= &ahci_avn_ops,
+	},
 	[board_ahci_mcp65] = {
 		AHCI_HFLAGS	(AHCI_HFLAG_NO_FPDMA_AA | AHCI_HFLAG_NO_PMP |
 				 AHCI_HFLAG_YES_NCQ),
@@ -290,14 +304,14 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	{ PCI_VDEVICE(INTEL, 0x1f27), board_ahci }, /* Avoton RAID */
 	{ PCI_VDEVICE(INTEL, 0x1f2e), board_ahci }, /* Avoton RAID */
 	{ PCI_VDEVICE(INTEL, 0x1f2f), board_ahci }, /* Avoton RAID */
-	{ PCI_VDEVICE(INTEL, 0x1f32), board_ahci }, /* Avoton AHCI */
-	{ PCI_VDEVICE(INTEL, 0x1f33), board_ahci }, /* Avoton AHCI */
-	{ PCI_VDEVICE(INTEL, 0x1f34), board_ahci }, /* Avoton RAID */
-	{ PCI_VDEVICE(INTEL, 0x1f35), board_ahci }, /* Avoton RAID */
-	{ PCI_VDEVICE(INTEL, 0x1f36), board_ahci }, /* Avoton RAID */
-	{ PCI_VDEVICE(INTEL, 0x1f37), board_ahci }, /* Avoton RAID */
-	{ PCI_VDEVICE(INTEL, 0x1f3e), board_ahci }, /* Avoton RAID */
-	{ PCI_VDEVICE(INTEL, 0x1f3f), board_ahci }, /* Avoton RAID */
+	{ PCI_VDEVICE(INTEL, 0x1f32), board_ahci_avn }, /* Avoton AHCI */
+	{ PCI_VDEVICE(INTEL, 0x1f33), board_ahci_avn }, /* Avoton AHCI */
+	{ PCI_VDEVICE(INTEL, 0x1f34), board_ahci_avn }, /* Avoton RAID */
+	{ PCI_VDEVICE(INTEL, 0x1f35), board_ahci_avn }, /* Avoton RAID */
+	{ PCI_VDEVICE(INTEL, 0x1f36), board_ahci_avn }, /* Avoton RAID */
+	{ PCI_VDEVICE(INTEL, 0x1f37), board_ahci_avn }, /* Avoton RAID */
+	{ PCI_VDEVICE(INTEL, 0x1f3e), board_ahci_avn }, /* Avoton RAID */
+	{ PCI_VDEVICE(INTEL, 0x1f3f), board_ahci_avn }, /* Avoton RAID */
 	{ PCI_VDEVICE(INTEL, 0x2823), board_ahci }, /* Wellsburg RAID */
 	{ PCI_VDEVICE(INTEL, 0x2827), board_ahci }, /* Wellsburg RAID */
 	{ PCI_VDEVICE(INTEL, 0x8d02), board_ahci }, /* Wellsburg AHCI */
@@ -670,6 +684,79 @@ static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
 	return rc;
 }
 
+/*
+ * ahci_avn_hardreset - attempt more aggressive recovery of Avoton ports.
+ *
+ * It has been observed with some SSDs that the timing of events in the
+ * link synchronization phase can leave the port in a state that can not
+ * be recovered by a SATA-hard-reset alone.  The failing signature is
+ * SStatus.DET stuck at 1 ("Device presence detected but Phy
+ * communication not established").  It was found that unloading and
+ * reloading the driver when this problem occurs allows the drive
+ * connection to be recovered (DET advanced to 0x3).  The critical
+ * component of reloading the driver is that the port state machines are
+ * reset by bouncing "port enable" in the AHCI PCS configuration
+ * register.  So, reproduce that effect by bouncing a port whenever we
+ * see DET==1 after a reset.
+ */
+static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class,
+			      unsigned long deadline)
+{
+	const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+	struct ata_port *ap = link->ap;
+	struct ahci_port_priv *pp = ap->private_data;
+	struct ahci_host_priv *hpriv = ap->host->private_data;
+	u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+	unsigned long tmo = deadline - jiffies;
+	struct ata_taskfile tf;
+	bool online;
+	int rc, i;
+
+	DPRINTK("ENTER\n");
+
+	ahci_stop_engine(ap);
+
+	for (i = 0; i < 2; i++) {
+		u16 val;
+		u32 sstatus;
+		int port = ap->port_no;
+		struct ata_host *host = ap->host;
+		struct pci_dev *pdev = to_pci_dev(host->dev);
+
+		/* clear D2H reception area to properly wait for D2H FIS */
+		ata_tf_init(link->device, &tf);
+		tf.command = ATA_BUSY;
+		ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+
+		rc = sata_link_hardreset(link, timing, deadline, &online,
+				ahci_check_ready);
+
+		if (sata_scr_read(link, SCR_STATUS, &sstatus) != 0 ||
+				(sstatus & 0xf) != 1)
+			break;
+
+		ata_link_printk(link, KERN_INFO, "avn bounce port%d\n",
+				port);
+
+		pci_read_config_word(pdev, 0x92, &val);
+		val &= ~(1 << port);
+		pci_write_config_word(pdev, 0x92, val);
+		ata_msleep(ap, 1000);
+		val |= 1 << port;
+		pci_write_config_word(pdev, 0x92, val);
+		deadline += tmo;
+	}
+
+	hpriv->start_engine(ap);
+
+	if (online)
+		*class = ahci_dev_classify(ap);
+
+	DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
+	return rc;
+}
+
+
 #ifdef CONFIG_PM
 static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
 {
diff --git a/drivers/ata/ahci_st.c b/drivers/ata/ahci_st.c
index ea0ff00..8ff428f 100644
--- a/drivers/ata/ahci_st.c
+++ b/drivers/ata/ahci_st.c
@@ -37,7 +37,6 @@ struct st_ahci_drv_data {
 	struct reset_control *pwr;
 	struct reset_control *sw_rst;
 	struct reset_control *pwr_rst;
-	struct ahci_host_priv *hpriv;
 };
 
 static void st_ahci_configure_oob(void __iomem *mmio)
@@ -55,9 +54,10 @@ static void st_ahci_configure_oob(void __iomem *mmio)
 	writel(new_val, mmio + ST_AHCI_OOBR);
 }
 
-static int st_ahci_deassert_resets(struct device *dev)
+static int st_ahci_deassert_resets(struct ahci_host_priv *hpriv,
+				struct device *dev)
 {
-	struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
+	struct st_ahci_drv_data *drv_data = hpriv->plat_data;
 	int err;
 
 	if (drv_data->pwr) {
@@ -90,8 +90,8 @@ static int st_ahci_deassert_resets(struct device *dev)
 static void st_ahci_host_stop(struct ata_host *host)
 {
 	struct ahci_host_priv *hpriv = host->private_data;
+	struct st_ahci_drv_data *drv_data = hpriv->plat_data;
 	struct device *dev = host->dev;
-	struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
 	int err;
 
 	if (drv_data->pwr) {
@@ -103,29 +103,30 @@ static void st_ahci_host_stop(struct ata_host *host)
 	ahci_platform_disable_resources(hpriv);
 }
 
-static int st_ahci_probe_resets(struct platform_device *pdev)
+static int st_ahci_probe_resets(struct ahci_host_priv *hpriv,
+				struct device *dev)
 {
-	struct st_ahci_drv_data *drv_data = platform_get_drvdata(pdev);
+	struct st_ahci_drv_data *drv_data = hpriv->plat_data;
 
-	drv_data->pwr = devm_reset_control_get(&pdev->dev, "pwr-dwn");
+	drv_data->pwr = devm_reset_control_get(dev, "pwr-dwn");
 	if (IS_ERR(drv_data->pwr)) {
-		dev_info(&pdev->dev, "power reset control not defined\n");
+		dev_info(dev, "power reset control not defined\n");
 		drv_data->pwr = NULL;
 	}
 
-	drv_data->sw_rst = devm_reset_control_get(&pdev->dev, "sw-rst");
+	drv_data->sw_rst = devm_reset_control_get(dev, "sw-rst");
 	if (IS_ERR(drv_data->sw_rst)) {
-		dev_info(&pdev->dev, "soft reset control not defined\n");
+		dev_info(dev, "soft reset control not defined\n");
 		drv_data->sw_rst = NULL;
 	}
 
-	drv_data->pwr_rst = devm_reset_control_get(&pdev->dev, "pwr-rst");
+	drv_data->pwr_rst = devm_reset_control_get(dev, "pwr-rst");
 	if (IS_ERR(drv_data->pwr_rst)) {
-		dev_dbg(&pdev->dev, "power soft reset control not defined\n");
+		dev_dbg(dev, "power soft reset control not defined\n");
 		drv_data->pwr_rst = NULL;
 	}
 
-	return st_ahci_deassert_resets(&pdev->dev);
+	return st_ahci_deassert_resets(hpriv, dev);
 }
 
 static struct ata_port_operations st_ahci_port_ops = {
@@ -154,15 +155,12 @@ static int st_ahci_probe(struct platform_device *pdev)
 	if (!drv_data)
 		return -ENOMEM;
 
-	platform_set_drvdata(pdev, drv_data);
-
 	hpriv = ahci_platform_get_resources(pdev);
 	if (IS_ERR(hpriv))
 		return PTR_ERR(hpriv);
+	hpriv->plat_data = drv_data;
 
-	drv_data->hpriv = hpriv;
-
-	err = st_ahci_probe_resets(pdev);
+	err = st_ahci_probe_resets(hpriv, &pdev->dev);
 	if (err)
 		return err;
 
@@ -170,7 +168,7 @@ static int st_ahci_probe(struct platform_device *pdev)
 	if (err)
 		return err;
 
-	st_ahci_configure_oob(drv_data->hpriv->mmio);
+	st_ahci_configure_oob(hpriv->mmio);
 
 	err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info,
 				      &ahci_platform_sht);
@@ -185,8 +183,9 @@ static int st_ahci_probe(struct platform_device *pdev)
 #ifdef CONFIG_PM_SLEEP
 static int st_ahci_suspend(struct device *dev)
 {
-	struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = drv_data->hpriv;
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	struct st_ahci_drv_data *drv_data = hpriv->plat_data;
 	int err;
 
 	err = ahci_platform_suspend_host(dev);
@@ -208,21 +207,21 @@ static int st_ahci_suspend(struct device *dev)
 
 static int st_ahci_resume(struct device *dev)
 {
-	struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
-	struct ahci_host_priv *hpriv = drv_data->hpriv;
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
 	int err;
 
 	err = ahci_platform_enable_resources(hpriv);
 	if (err)
 		return err;
 
-	err = st_ahci_deassert_resets(dev);
+	err = st_ahci_deassert_resets(hpriv, dev);
 	if (err) {
 		ahci_platform_disable_resources(hpriv);
 		return err;
 	}
 
-	st_ahci_configure_oob(drv_data->hpriv->mmio);
+	st_ahci_configure_oob(hpriv->mmio);
 
 	return ahci_platform_resume_host(dev);
 }
diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c
index 61a9c07..287c4ba 100644
--- a/drivers/ata/libahci.c
+++ b/drivers/ata/libahci.c
@@ -1707,8 +1707,7 @@ static void ahci_handle_port_interrupt(struct ata_port *ap,
 	if (unlikely(resetting))
 		status &= ~PORT_IRQ_BAD_PMP;
 
-	/* if LPM is enabled, PHYRDY doesn't mean anything */
-	if (ap->link.lpm_policy > ATA_LPM_MAX_POWER) {
+	if (sata_lpm_ignore_phy_events(&ap->link)) {
 		status &= ~PORT_IRQ_PHYRDY;
 		ahci_scr_write(&ap->link, SCR_ERROR, SERR_PHYRDY_CHG);
 	}
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index f6cb1f1..577849c 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -4235,7 +4235,7 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 	{ "Crucial_CT*MX100*",		"MU01",	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
-	{ "Samsung SSD 850 PRO*",	NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
+	{ "Samsung SSD 8*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 
 	/*
@@ -6752,6 +6752,38 @@ u32 ata_wait_register(struct ata_port *ap, void __iomem *reg, u32 mask, u32 val,
 	return tmp;
 }
 
+/**
+ *	sata_lpm_ignore_phy_events - test if PHY event should be ignored
+ *	@link: Link receiving the event
+ *
+ *	Test whether the received PHY event has to be ignored or not.
+ *
+ *	LOCKING:
+ *	None:
+ *
+ *	RETURNS:
+ *	True if the event has to be ignored.
+ */
+bool sata_lpm_ignore_phy_events(struct ata_link *link)
+{
+	unsigned long lpm_timeout = link->last_lpm_change +
+				    msecs_to_jiffies(ATA_TMOUT_SPURIOUS_PHY);
+
+	/* if LPM is enabled, PHYRDY doesn't mean anything */
+	if (link->lpm_policy > ATA_LPM_MAX_POWER)
+		return true;
+
+	/* ignore the first PHY event after the LPM policy changed
+	 * as it is might be spurious
+	 */
+	if ((link->flags & ATA_LFLAG_CHANGED) &&
+	    time_before(jiffies, lpm_timeout))
+		return true;
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(sata_lpm_ignore_phy_events);
+
 /*
  * Dummy port_ops
  */
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 07f41be..cf0022e 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -3597,6 +3597,9 @@ static int ata_eh_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
 		}
 	}
 
+	link->last_lpm_change = jiffies;
+	link->flags |= ATA_LFLAG_CHANGED;
+
 	return 0;
 
 fail:
diff --git a/drivers/ata/pata_scc.c b/drivers/ata/pata_scc.c
deleted file mode 100644
index 5cd60d6..0000000
--- a/drivers/ata/pata_scc.c
+++ /dev/null
@@ -1,1110 +0,0 @@
-/*
- * Support for IDE interfaces on Celleb platform
- *
- * (C) Copyright 2006 TOSHIBA CORPORATION
- *
- * This code is based on drivers/ata/ata_piix.c:
- *  Copyright 2003-2005 Red Hat Inc
- *  Copyright 2003-2005 Jeff Garzik
- *  Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
- *  Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- *  Copyright (C) 2003 Red Hat Inc
- *
- * and drivers/ata/ahci.c:
- *  Copyright 2004-2005 Red Hat, Inc.
- *
- * and drivers/ata/libata-core.c:
- *  Copyright 2003-2004 Red Hat, Inc.  All rights reserved.
- *  Copyright 2003-2004 Jeff Garzik
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/blkdev.h>
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <scsi/scsi_host.h>
-#include <linux/libata.h>
-
-#define DRV_NAME		"pata_scc"
-#define DRV_VERSION		"0.3"
-
-#define PCI_DEVICE_ID_TOSHIBA_SCC_ATA		0x01b4
-
-/* PCI BARs */
-#define SCC_CTRL_BAR		0
-#define SCC_BMID_BAR		1
-
-/* offset of CTRL registers */
-#define SCC_CTL_PIOSHT		0x000
-#define SCC_CTL_PIOCT		0x004
-#define SCC_CTL_MDMACT		0x008
-#define SCC_CTL_MCRCST		0x00C
-#define SCC_CTL_SDMACT		0x010
-#define SCC_CTL_SCRCST		0x014
-#define SCC_CTL_UDENVT		0x018
-#define SCC_CTL_TDVHSEL 	0x020
-#define SCC_CTL_MODEREG 	0x024
-#define SCC_CTL_ECMODE		0xF00
-#define SCC_CTL_MAEA0		0xF50
-#define SCC_CTL_MAEC0		0xF54
-#define SCC_CTL_CCKCTRL 	0xFF0
-
-/* offset of BMID registers */
-#define SCC_DMA_CMD		0x000
-#define SCC_DMA_STATUS		0x004
-#define SCC_DMA_TABLE_OFS	0x008
-#define SCC_DMA_INTMASK 	0x010
-#define SCC_DMA_INTST		0x014
-#define SCC_DMA_PTERADD 	0x018
-#define SCC_REG_CMD_ADDR	0x020
-#define SCC_REG_DATA		0x000
-#define SCC_REG_ERR		0x004
-#define SCC_REG_FEATURE 	0x004
-#define SCC_REG_NSECT		0x008
-#define SCC_REG_LBAL		0x00C
-#define SCC_REG_LBAM		0x010
-#define SCC_REG_LBAH		0x014
-#define SCC_REG_DEVICE		0x018
-#define SCC_REG_STATUS		0x01C
-#define SCC_REG_CMD		0x01C
-#define SCC_REG_ALTSTATUS	0x020
-
-/* register value */
-#define TDVHSEL_MASTER		0x00000001
-#define TDVHSEL_SLAVE		0x00000004
-
-#define MODE_JCUSFEN		0x00000080
-
-#define ECMODE_VALUE		0x01
-
-#define CCKCTRL_ATARESET	0x00040000
-#define CCKCTRL_BUFCNT		0x00020000
-#define CCKCTRL_CRST		0x00010000
-#define CCKCTRL_OCLKEN		0x00000100
-#define CCKCTRL_ATACLKOEN	0x00000002
-#define CCKCTRL_LCLKEN		0x00000001
-
-#define QCHCD_IOS_SS		0x00000001
-
-#define QCHSD_STPDIAG		0x00020000
-
-#define INTMASK_MSK		0xD1000012
-#define INTSTS_SERROR		0x80000000
-#define INTSTS_PRERR		0x40000000
-#define INTSTS_RERR		0x10000000
-#define INTSTS_ICERR		0x01000000
-#define INTSTS_BMSINT		0x00000010
-#define INTSTS_BMHE		0x00000008
-#define INTSTS_IOIRQS		0x00000004
-#define INTSTS_INTRQ		0x00000002
-#define INTSTS_ACTEINT		0x00000001
-
-
-/* PIO transfer mode table */
-/* JCHST */
-static const unsigned long JCHSTtbl[2][7] = {
-	{0x0E, 0x05, 0x02, 0x03, 0x02, 0x00, 0x00},	/* 100MHz */
-	{0x13, 0x07, 0x04, 0x04, 0x03, 0x00, 0x00}	/* 133MHz */
-};
-
-/* JCHHT */
-static const unsigned long JCHHTtbl[2][7] = {
-	{0x0E, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00},	/* 100MHz */
-	{0x13, 0x03, 0x03, 0x03, 0x03, 0x00, 0x00}	/* 133MHz */
-};
-
-/* JCHCT */
-static const unsigned long JCHCTtbl[2][7] = {
-	{0x1D, 0x1D, 0x1C, 0x0B, 0x06, 0x00, 0x00},	/* 100MHz */
-	{0x27, 0x26, 0x26, 0x0E, 0x09, 0x00, 0x00}	/* 133MHz */
-};
-
-/* DMA transfer mode  table */
-/* JCHDCTM/JCHDCTS */
-static const unsigned long JCHDCTxtbl[2][7] = {
-	{0x0A, 0x06, 0x04, 0x03, 0x01, 0x00, 0x00},	/* 100MHz */
-	{0x0E, 0x09, 0x06, 0x04, 0x02, 0x01, 0x00}	/* 133MHz */
-};
-
-/* JCSTWTM/JCSTWTS  */
-static const unsigned long JCSTWTxtbl[2][7] = {
-	{0x06, 0x04, 0x03, 0x02, 0x02, 0x02, 0x00},	/* 100MHz */
-	{0x09, 0x06, 0x04, 0x02, 0x02, 0x02, 0x02}	/* 133MHz */
-};
-
-/* JCTSS */
-static const unsigned long JCTSStbl[2][7] = {
-	{0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x00},	/* 100MHz */
-	{0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x05}	/* 133MHz */
-};
-
-/* JCENVT */
-static const unsigned long JCENVTtbl[2][7] = {
-	{0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00},	/* 100MHz */
-	{0x02, 0x02, 0x02, 0x02, 0x02, 0x02, 0x02}	/* 133MHz */
-};
-
-/* JCACTSELS/JCACTSELM */
-static const unsigned long JCACTSELtbl[2][7] = {
-	{0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00},	/* 100MHz */
-	{0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01}	/* 133MHz */
-};
-
-static const struct pci_device_id scc_pci_tbl[] = {
-	{ PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA), 0},
-	{ }	/* terminate list */
-};
-
-/**
- *	scc_set_piomode - Initialize host controller PATA PIO timings
- *	@ap: Port whose timings we are configuring
- *	@adev: um
- *
- *	Set PIO mode for device.
- *
- *	LOCKING:
- *	None (inherited from caller).
- */
-
-static void scc_set_piomode (struct ata_port *ap, struct ata_device *adev)
-{
-	unsigned int pio = adev->pio_mode - XFER_PIO_0;
-	void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
-	void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
-	void __iomem *piosht_port = ctrl_base + SCC_CTL_PIOSHT;
-	void __iomem *pioct_port = ctrl_base + SCC_CTL_PIOCT;
-	unsigned long reg;
-	int offset;
-
-	reg = in_be32(cckctrl_port);
-	if (reg & CCKCTRL_ATACLKOEN)
-		offset = 1;	/* 133MHz */
-	else
-		offset = 0;	/* 100MHz */
-
-	reg = JCHSTtbl[offset][pio] << 16 | JCHHTtbl[offset][pio];
-	out_be32(piosht_port, reg);
-	reg = JCHCTtbl[offset][pio];
-	out_be32(pioct_port, reg);
-}
-
-/**
- *	scc_set_dmamode - Initialize host controller PATA DMA timings
- *	@ap: Port whose timings we are configuring
- *	@adev: um
- *
- *	Set UDMA mode for device.
- *
- *	LOCKING:
- *	None (inherited from caller).
- */
-
-static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev)
-{
-	unsigned int udma = adev->dma_mode;
-	unsigned int is_slave = (adev->devno != 0);
-	u8 speed = udma;
-	void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
-	void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
-	void __iomem *mdmact_port = ctrl_base + SCC_CTL_MDMACT;
-	void __iomem *mcrcst_port = ctrl_base + SCC_CTL_MCRCST;
-	void __iomem *sdmact_port = ctrl_base + SCC_CTL_SDMACT;
-	void __iomem *scrcst_port = ctrl_base + SCC_CTL_SCRCST;
-	void __iomem *udenvt_port = ctrl_base + SCC_CTL_UDENVT;
-	void __iomem *tdvhsel_port = ctrl_base + SCC_CTL_TDVHSEL;
-	int offset, idx;
-
-	if (in_be32(cckctrl_port) & CCKCTRL_ATACLKOEN)
-		offset = 1;	/* 133MHz */
-	else
-		offset = 0;	/* 100MHz */
-
-	if (speed >= XFER_UDMA_0)
-		idx = speed - XFER_UDMA_0;
-	else
-		return;
-
-	if (is_slave) {
-		out_be32(sdmact_port, JCHDCTxtbl[offset][idx]);
-		out_be32(scrcst_port, JCSTWTxtbl[offset][idx]);
-		out_be32(tdvhsel_port,
-			 (in_be32(tdvhsel_port) & ~TDVHSEL_SLAVE) | (JCACTSELtbl[offset][idx] << 2));
-	} else {
-		out_be32(mdmact_port, JCHDCTxtbl[offset][idx]);
-		out_be32(mcrcst_port, JCSTWTxtbl[offset][idx]);
-		out_be32(tdvhsel_port,
-			 (in_be32(tdvhsel_port) & ~TDVHSEL_MASTER) | JCACTSELtbl[offset][idx]);
-	}
-	out_be32(udenvt_port,
-		 JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx]);
-}
-
-unsigned long scc_mode_filter(struct ata_device *adev, unsigned long mask)
-{
-	/* errata A308 workaround: limit ATAPI UDMA mode to UDMA4 */
-	if (adev->class == ATA_DEV_ATAPI &&
-	    (mask & (0xE0 << ATA_SHIFT_UDMA))) {
-		printk(KERN_INFO "%s: limit ATAPI UDMA to UDMA4\n", DRV_NAME);
-		mask &= ~(0xE0 << ATA_SHIFT_UDMA);
-	}
-	return mask;
-}
-
-/**
- *	scc_tf_load - send taskfile registers to host controller
- *	@ap: Port to which output is sent
- *	@tf: ATA taskfile register set
- *
- *	Note: Original code is ata_sff_tf_load().
- */
-
-static void scc_tf_load (struct ata_port *ap, const struct ata_taskfile *tf)
-{
-	struct ata_ioports *ioaddr = &ap->ioaddr;
-	unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
-
-	if (tf->ctl != ap->last_ctl) {
-		out_be32(ioaddr->ctl_addr, tf->ctl);
-		ap->last_ctl = tf->ctl;
-		ata_wait_idle(ap);
-	}
-
-	if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
-		out_be32(ioaddr->feature_addr, tf->hob_feature);
-		out_be32(ioaddr->nsect_addr, tf->hob_nsect);
-		out_be32(ioaddr->lbal_addr, tf->hob_lbal);
-		out_be32(ioaddr->lbam_addr, tf->hob_lbam);
-		out_be32(ioaddr->lbah_addr, tf->hob_lbah);
-		VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
-			tf->hob_feature,
-			tf->hob_nsect,
-			tf->hob_lbal,
-			tf->hob_lbam,
-			tf->hob_lbah);
-	}
-
-	if (is_addr) {
-		out_be32(ioaddr->feature_addr, tf->feature);
-		out_be32(ioaddr->nsect_addr, tf->nsect);
-		out_be32(ioaddr->lbal_addr, tf->lbal);
-		out_be32(ioaddr->lbam_addr, tf->lbam);
-		out_be32(ioaddr->lbah_addr, tf->lbah);
-		VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
-			tf->feature,
-			tf->nsect,
-			tf->lbal,
-			tf->lbam,
-			tf->lbah);
-	}
-
-	if (tf->flags & ATA_TFLAG_DEVICE) {
-		out_be32(ioaddr->device_addr, tf->device);
-		VPRINTK("device 0x%X\n", tf->device);
-	}
-
-	ata_wait_idle(ap);
-}
-
-/**
- *	scc_check_status - Read device status reg & clear interrupt
- *	@ap: port where the device is
- *
- *	Note: Original code is ata_check_status().
- */
-
-static u8 scc_check_status (struct ata_port *ap)
-{
-	return in_be32(ap->ioaddr.status_addr);
-}
-
-/**
- *	scc_tf_read - input device's ATA taskfile shadow registers
- *	@ap: Port from which input is read
- *	@tf: ATA taskfile register set for storing input
- *
- *	Note: Original code is ata_sff_tf_read().
- */
-
-static void scc_tf_read (struct ata_port *ap, struct ata_taskfile *tf)
-{
-	struct ata_ioports *ioaddr = &ap->ioaddr;
-
-	tf->command = scc_check_status(ap);
-	tf->feature = in_be32(ioaddr->error_addr);
-	tf->nsect = in_be32(ioaddr->nsect_addr);
-	tf->lbal = in_be32(ioaddr->lbal_addr);
-	tf->lbam = in_be32(ioaddr->lbam_addr);
-	tf->lbah = in_be32(ioaddr->lbah_addr);
-	tf->device = in_be32(ioaddr->device_addr);
-
-	if (tf->flags & ATA_TFLAG_LBA48) {
-		out_be32(ioaddr->ctl_addr, tf->ctl | ATA_HOB);
-		tf->hob_feature = in_be32(ioaddr->error_addr);
-		tf->hob_nsect = in_be32(ioaddr->nsect_addr);
-		tf->hob_lbal = in_be32(ioaddr->lbal_addr);
-		tf->hob_lbam = in_be32(ioaddr->lbam_addr);
-		tf->hob_lbah = in_be32(ioaddr->lbah_addr);
-		out_be32(ioaddr->ctl_addr, tf->ctl);
-		ap->last_ctl = tf->ctl;
-	}
-}
-
-/**
- *	scc_exec_command - issue ATA command to host controller
- *	@ap: port to which command is being issued
- *	@tf: ATA taskfile register set
- *
- *	Note: Original code is ata_sff_exec_command().
- */
-
-static void scc_exec_command (struct ata_port *ap,
-			      const struct ata_taskfile *tf)
-{
-	DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
-
-	out_be32(ap->ioaddr.command_addr, tf->command);
-	ata_sff_pause(ap);
-}
-
-/**
- *	scc_check_altstatus - Read device alternate status reg
- *	@ap: port where the device is
- */
-
-static u8 scc_check_altstatus (struct ata_port *ap)
-{
-	return in_be32(ap->ioaddr.altstatus_addr);
-}
-
-/**
- *	scc_dev_select - Select device 0/1 on ATA bus
- *	@ap: ATA channel to manipulate
- *	@device: ATA device (numbered from zero) to select
- *
- *	Note: Original code is ata_sff_dev_select().
- */
-
-static void scc_dev_select (struct ata_port *ap, unsigned int device)
-{
-	u8 tmp;
-
-	if (device == 0)
-		tmp = ATA_DEVICE_OBS;
-	else
-		tmp = ATA_DEVICE_OBS | ATA_DEV1;
-
-	out_be32(ap->ioaddr.device_addr, tmp);
-	ata_sff_pause(ap);
-}
-
-/**
- *	scc_set_devctl - Write device control reg
- *	@ap: port where the device is
- *	@ctl: value to write
- */
-
-static void scc_set_devctl(struct ata_port *ap, u8 ctl)
-{
-	out_be32(ap->ioaddr.ctl_addr, ctl);
-}
-
-/**
- *	scc_bmdma_setup - Set up PCI IDE BMDMA transaction
- *	@qc: Info associated with this ATA transaction.
- *
- *	Note: Original code is ata_bmdma_setup().
- */
-
-static void scc_bmdma_setup (struct ata_queued_cmd *qc)
-{
-	struct ata_port *ap = qc->ap;
-	unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
-	u8 dmactl;
-	void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
-	/* load PRD table addr */
-	out_be32(mmio + SCC_DMA_TABLE_OFS, ap->bmdma_prd_dma);
-
-	/* specify data direction, triple-check start bit is clear */
-	dmactl = in_be32(mmio + SCC_DMA_CMD);
-	dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
-	if (!rw)
-		dmactl |= ATA_DMA_WR;
-	out_be32(mmio + SCC_DMA_CMD, dmactl);
-
-	/* issue r/w command */
-	ap->ops->sff_exec_command(ap, &qc->tf);
-}
-
-/**
- *	scc_bmdma_start - Start a PCI IDE BMDMA transaction
- *	@qc: Info associated with this ATA transaction.
- *
- *	Note: Original code is ata_bmdma_start().
- */
-
-static void scc_bmdma_start (struct ata_queued_cmd *qc)
-{
-	struct ata_port *ap = qc->ap;
-	u8 dmactl;
-	void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
-	/* start host DMA transaction */
-	dmactl = in_be32(mmio + SCC_DMA_CMD);
-	out_be32(mmio + SCC_DMA_CMD, dmactl | ATA_DMA_START);
-}
-
-/**
- *	scc_devchk - PATA device presence detection
- *	@ap: ATA channel to examine
- *	@device: Device to examine (starting at zero)
- *
- *	Note: Original code is ata_devchk().
- */
-
-static unsigned int scc_devchk (struct ata_port *ap,
-				unsigned int device)
-{
-	struct ata_ioports *ioaddr = &ap->ioaddr;
-	u8 nsect, lbal;
-
-	ap->ops->sff_dev_select(ap, device);
-
-	out_be32(ioaddr->nsect_addr, 0x55);
-	out_be32(ioaddr->lbal_addr, 0xaa);
-
-	out_be32(ioaddr->nsect_addr, 0xaa);
-	out_be32(ioaddr->lbal_addr, 0x55);
-
-	out_be32(ioaddr->nsect_addr, 0x55);
-	out_be32(ioaddr->lbal_addr, 0xaa);
-
-	nsect = in_be32(ioaddr->nsect_addr);
-	lbal = in_be32(ioaddr->lbal_addr);
-
-	if ((nsect == 0x55) && (lbal == 0xaa))
-		return 1;	/* we found a device */
-
-	return 0;		/* nothing found */
-}
-
-/**
- *	scc_wait_after_reset - wait for devices to become ready after reset
- *
- *	Note: Original code is ata_sff_wait_after_reset
- */
-
-static int scc_wait_after_reset(struct ata_link *link, unsigned int devmask,
-				unsigned long deadline)
-{
-	struct ata_port *ap = link->ap;
-	struct ata_ioports *ioaddr = &ap->ioaddr;
-	unsigned int dev0 = devmask & (1 << 0);
-	unsigned int dev1 = devmask & (1 << 1);
-	int rc, ret = 0;
-
-	/* Spec mandates ">= 2ms" before checking status.  We wait
-	 * 150ms, because that was the magic delay used for ATAPI
-	 * devices in Hale Landis's ATADRVR, for the period of time
-	 * between when the ATA command register is written, and then
-	 * status is checked.  Because waiting for "a while" before
-	 * checking status is fine, post SRST, we perform this magic
-	 * delay here as well.
-	 *
-	 * Old drivers/ide uses the 2mS rule and then waits for ready.
-	 */
-	ata_msleep(ap, 150);
-
-	/* always check readiness of the master device */
-	rc = ata_sff_wait_ready(link, deadline);
-	/* -ENODEV means the odd clown forgot the D7 pulldown resistor
-	 * and TF status is 0xff, bail out on it too.
-	 */
-	if (rc)
-		return rc;
-
-	/* if device 1 was found in ata_devchk, wait for register
-	 * access briefly, then wait for BSY to clear.
-	 */
-	if (dev1) {
-		int i;
-
-		ap->ops->sff_dev_select(ap, 1);
-
-		/* Wait for register access.  Some ATAPI devices fail
-		 * to set nsect/lbal after reset, so don't waste too
-		 * much time on it.  We're gonna wait for !BSY anyway.
-		 */
-		for (i = 0; i < 2; i++) {
-			u8 nsect, lbal;
-
-			nsect = in_be32(ioaddr->nsect_addr);
-			lbal = in_be32(ioaddr->lbal_addr);
-			if ((nsect == 1) && (lbal == 1))
-				break;
-			ata_msleep(ap, 50);	/* give drive a breather */
-		}
-
-		rc = ata_sff_wait_ready(link, deadline);
-		if (rc) {
-			if (rc != -ENODEV)
-				return rc;
-			ret = rc;
-		}
-	}
-
-	/* is all this really necessary? */
-	ap->ops->sff_dev_select(ap, 0);
-	if (dev1)
-		ap->ops->sff_dev_select(ap, 1);
-	if (dev0)
-		ap->ops->sff_dev_select(ap, 0);
-
-	return ret;
-}
-
-/**
- *	scc_bus_softreset - PATA device software reset
- *
- *	Note: Original code is ata_bus_softreset().
- */
-
-static int scc_bus_softreset(struct ata_port *ap, unsigned int devmask,
-                                      unsigned long deadline)
-{
-	struct ata_ioports *ioaddr = &ap->ioaddr;
-
-	DPRINTK("ata%u: bus reset via SRST\n", ap->print_id);
-
-	/* software reset.  causes dev0 to be selected */
-	out_be32(ioaddr->ctl_addr, ap->ctl);
-	udelay(20);
-	out_be32(ioaddr->ctl_addr, ap->ctl | ATA_SRST);
-	udelay(20);
-	out_be32(ioaddr->ctl_addr, ap->ctl);
-
-	return scc_wait_after_reset(&ap->link, devmask, deadline);
-}
-
-/**
- *	scc_softreset - reset host port via ATA SRST
- *	@ap: port to reset
- *	@classes: resulting classes of attached devices
- *	@deadline: deadline jiffies for the operation
- *
- *	Note: Original code is ata_sff_softreset().
- */
-
-static int scc_softreset(struct ata_link *link, unsigned int *classes,
-			 unsigned long deadline)
-{
-	struct ata_port *ap = link->ap;
-	unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
-	unsigned int devmask = 0;
-	int rc;
-	u8 err;
-
-	DPRINTK("ENTER\n");
-
-	/* determine if device 0/1 are present */
-	if (scc_devchk(ap, 0))
-		devmask |= (1 << 0);
-	if (slave_possible && scc_devchk(ap, 1))
-		devmask |= (1 << 1);
-
-	/* select device 0 again */
-	ap->ops->sff_dev_select(ap, 0);
-
-	/* issue bus reset */
-	DPRINTK("about to softreset, devmask=%x\n", devmask);
-	rc = scc_bus_softreset(ap, devmask, deadline);
-	if (rc) {
-		ata_port_err(ap, "SRST failed (err_mask=0x%x)\n", rc);
-		return -EIO;
-	}
-
-	/* determine by signature whether we have ATA or ATAPI devices */
-	classes[0] = ata_sff_dev_classify(&ap->link.device[0],
-					  devmask & (1 << 0), &err);
-	if (slave_possible && err != 0x81)
-		classes[1] = ata_sff_dev_classify(&ap->link.device[1],
-						  devmask & (1 << 1), &err);
-
-	DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
-	return 0;
-}
-
-/**
- *	scc_bmdma_stop - Stop PCI IDE BMDMA transfer
- *	@qc: Command we are ending DMA for
- */
-
-static void scc_bmdma_stop (struct ata_queued_cmd *qc)
-{
-	struct ata_port *ap = qc->ap;
-	void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
-	void __iomem *bmid_base = ap->host->iomap[SCC_BMID_BAR];
-	u32 reg;
-
-	while (1) {
-		reg = in_be32(bmid_base + SCC_DMA_INTST);
-
-		if (reg & INTSTS_SERROR) {
-			printk(KERN_WARNING "%s: SERROR\n", DRV_NAME);
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_SERROR|INTSTS_BMSINT);
-			out_be32(bmid_base + SCC_DMA_CMD,
-				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
-			continue;
-		}
-
-		if (reg & INTSTS_PRERR) {
-			u32 maea0, maec0;
-			maea0 = in_be32(ctrl_base + SCC_CTL_MAEA0);
-			maec0 = in_be32(ctrl_base + SCC_CTL_MAEC0);
-			printk(KERN_WARNING "%s: PRERR [addr:%x cmd:%x]\n", DRV_NAME, maea0, maec0);
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_PRERR|INTSTS_BMSINT);
-			out_be32(bmid_base + SCC_DMA_CMD,
-				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
-			continue;
-		}
-
-		if (reg & INTSTS_RERR) {
-			printk(KERN_WARNING "%s: Response Error\n", DRV_NAME);
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_RERR|INTSTS_BMSINT);
-			out_be32(bmid_base + SCC_DMA_CMD,
-				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
-			continue;
-		}
-
-		if (reg & INTSTS_ICERR) {
-			out_be32(bmid_base + SCC_DMA_CMD,
-				 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
-			printk(KERN_WARNING "%s: Illegal Configuration\n", DRV_NAME);
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ICERR|INTSTS_BMSINT);
-			continue;
-		}
-
-		if (reg & INTSTS_BMSINT) {
-			unsigned int classes;
-			unsigned long deadline = ata_deadline(jiffies, ATA_TMOUT_BOOT);
-			printk(KERN_WARNING "%s: Internal Bus Error\n", DRV_NAME);
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMSINT);
-			/* TBD: SW reset */
-			scc_softreset(&ap->link, &classes, deadline);
-			continue;
-		}
-
-		if (reg & INTSTS_BMHE) {
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMHE);
-			continue;
-		}
-
-		if (reg & INTSTS_ACTEINT) {
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ACTEINT);
-			continue;
-		}
-
-		if (reg & INTSTS_IOIRQS) {
-			out_be32(bmid_base + SCC_DMA_INTST, INTSTS_IOIRQS);
-			continue;
-		}
-		break;
-	}
-
-	/* clear start/stop bit */
-	out_be32(bmid_base + SCC_DMA_CMD,
-		 in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
-
-	/* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
-	ata_sff_dma_pause(ap);	/* dummy read */
-}
-
-/**
- *	scc_bmdma_status - Read PCI IDE BMDMA status
- *	@ap: Port associated with this ATA transaction.
- */
-
-static u8 scc_bmdma_status (struct ata_port *ap)
-{
-	void __iomem *mmio = ap->ioaddr.bmdma_addr;
-	u8 host_stat = in_be32(mmio + SCC_DMA_STATUS);
-	u32 int_status = in_be32(mmio + SCC_DMA_INTST);
-	struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->link.active_tag);
-	static int retry = 0;
-
-	/* return if IOS_SS is cleared */
-	if (!(in_be32(mmio + SCC_DMA_CMD) & ATA_DMA_START))
-		return host_stat;
-
-	/* errata A252,A308 workaround: Step4 */
-	if ((scc_check_altstatus(ap) & ATA_ERR)
-					&& (int_status & INTSTS_INTRQ))
-		return (host_stat | ATA_DMA_INTR);
-
-	/* errata A308 workaround Step5 */
-	if (int_status & INTSTS_IOIRQS) {
-		host_stat |= ATA_DMA_INTR;
-
-		/* We don't check ATAPI DMA because it is limited to UDMA4 */
-		if ((qc->tf.protocol == ATA_PROT_DMA &&
-		     qc->dev->xfer_mode > XFER_UDMA_4)) {
-			if (!(int_status & INTSTS_ACTEINT)) {
-				printk(KERN_WARNING "ata%u: operation failed (transfer data loss)\n",
-				       ap->print_id);
-				host_stat |= ATA_DMA_ERR;
-				if (retry++)
-					ap->udma_mask &= ~(1 << qc->dev->xfer_mode);
-			} else
-				retry = 0;
-		}
-	}
-
-	return host_stat;
-}
-
-/**
- *	scc_data_xfer - Transfer data by PIO
- *	@dev: device for this I/O
- *	@buf: data buffer
- *	@buflen: buffer length
- *	@rw: read/write
- *
- *	Note: Original code is ata_sff_data_xfer().
- */
-
-static unsigned int scc_data_xfer (struct ata_device *dev, unsigned char *buf,
-				   unsigned int buflen, int rw)
-{
-	struct ata_port *ap = dev->link->ap;
-	unsigned int words = buflen >> 1;
-	unsigned int i;
-	__le16 *buf16 = (__le16 *) buf;
-	void __iomem *mmio = ap->ioaddr.data_addr;
-
-	/* Transfer multiple of 2 bytes */
-	if (rw == READ)
-		for (i = 0; i < words; i++)
-			buf16[i] = cpu_to_le16(in_be32(mmio));
-	else
-		for (i = 0; i < words; i++)
-			out_be32(mmio, le16_to_cpu(buf16[i]));
-
-	/* Transfer trailing 1 byte, if any. */
-	if (unlikely(buflen & 0x01)) {
-		__le16 align_buf[1] = { 0 };
-		unsigned char *trailing_buf = buf + buflen - 1;
-
-		if (rw == READ) {
-			align_buf[0] = cpu_to_le16(in_be32(mmio));
-			memcpy(trailing_buf, align_buf, 1);
-		} else {
-			memcpy(align_buf, trailing_buf, 1);
-			out_be32(mmio, le16_to_cpu(align_buf[0]));
-		}
-		words++;
-	}
-
-	return words << 1;
-}
-
-/**
- *	scc_postreset - standard postreset callback
- *	@ap: the target ata_port
- *	@classes: classes of attached devices
- *
- *	Note: Original code is ata_sff_postreset().
- */
-
-static void scc_postreset(struct ata_link *link, unsigned int *classes)
-{
-	struct ata_port *ap = link->ap;
-
-	DPRINTK("ENTER\n");
-
-	/* is double-select really necessary? */
-	if (classes[0] != ATA_DEV_NONE)
-		ap->ops->sff_dev_select(ap, 1);
-	if (classes[1] != ATA_DEV_NONE)
-		ap->ops->sff_dev_select(ap, 0);
-
-	/* bail out if no device is present */
-	if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
-		DPRINTK("EXIT, no device\n");
-		return;
-	}
-
-	/* set up device control */
-	out_be32(ap->ioaddr.ctl_addr, ap->ctl);
-
-	DPRINTK("EXIT\n");
-}
-
-/**
- *	scc_irq_clear - Clear PCI IDE BMDMA interrupt.
- *	@ap: Port associated with this ATA transaction.
- *
- *	Note: Original code is ata_bmdma_irq_clear().
- */
-
-static void scc_irq_clear (struct ata_port *ap)
-{
-	void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
-	if (!mmio)
-		return;
-
-	out_be32(mmio + SCC_DMA_STATUS, in_be32(mmio + SCC_DMA_STATUS));
-}
-
-/**
- *	scc_port_start - Set port up for dma.
- *	@ap: Port to initialize
- *
- *	Allocate space for PRD table using ata_bmdma_port_start().
- *	Set PRD table address for PTERADD. (PRD Transfer End Read)
- */
-
-static int scc_port_start (struct ata_port *ap)
-{
-	void __iomem *mmio = ap->ioaddr.bmdma_addr;
-	int rc;
-
-	rc = ata_bmdma_port_start(ap);
-	if (rc)
-		return rc;
-
-	out_be32(mmio + SCC_DMA_PTERADD, ap->bmdma_prd_dma);
-	return 0;
-}
-
-/**
- *	scc_port_stop - Undo scc_port_start()
- *	@ap: Port to shut down
- *
- *	Reset PTERADD.
- */
-
-static void scc_port_stop (struct ata_port *ap)
-{
-	void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
-	out_be32(mmio + SCC_DMA_PTERADD, 0);
-}
-
-static struct scsi_host_template scc_sht = {
-	ATA_BMDMA_SHT(DRV_NAME),
-};
-
-static struct ata_port_operations scc_pata_ops = {
-	.inherits		= &ata_bmdma_port_ops,
-
-	.set_piomode		= scc_set_piomode,
-	.set_dmamode		= scc_set_dmamode,
-	.mode_filter		= scc_mode_filter,
-
-	.sff_tf_load		= scc_tf_load,
-	.sff_tf_read		= scc_tf_read,
-	.sff_exec_command	= scc_exec_command,
-	.sff_check_status	= scc_check_status,
-	.sff_check_altstatus	= scc_check_altstatus,
-	.sff_dev_select		= scc_dev_select,
-	.sff_set_devctl		= scc_set_devctl,
-
-	.bmdma_setup		= scc_bmdma_setup,
-	.bmdma_start		= scc_bmdma_start,
-	.bmdma_stop		= scc_bmdma_stop,
-	.bmdma_status		= scc_bmdma_status,
-	.sff_data_xfer		= scc_data_xfer,
-
-	.cable_detect		= ata_cable_80wire,
-	.softreset		= scc_softreset,
-	.postreset		= scc_postreset,
-
-	.sff_irq_clear		= scc_irq_clear,
-
-	.port_start		= scc_port_start,
-	.port_stop		= scc_port_stop,
-};
-
-static struct ata_port_info scc_port_info[] = {
-	{
-		.flags		= ATA_FLAG_SLAVE_POSS,
-		.pio_mask	= ATA_PIO4,
-		/* No MWDMA */
-		.udma_mask	= ATA_UDMA6,
-		.port_ops	= &scc_pata_ops,
-	},
-};
-
-/**
- *	scc_reset_controller - initialize SCC PATA controller.
- */
-
-static int scc_reset_controller(struct ata_host *host)
-{
-	void __iomem *ctrl_base = host->iomap[SCC_CTRL_BAR];
-	void __iomem *bmid_base = host->iomap[SCC_BMID_BAR];
-	void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
-	void __iomem *mode_port = ctrl_base + SCC_CTL_MODEREG;
-	void __iomem *ecmode_port = ctrl_base + SCC_CTL_ECMODE;
-	void __iomem *intmask_port = bmid_base + SCC_DMA_INTMASK;
-	void __iomem *dmastatus_port = bmid_base + SCC_DMA_STATUS;
-	u32 reg = 0;
-
-	out_be32(cckctrl_port, reg);
-	reg |= CCKCTRL_ATACLKOEN;
-	out_be32(cckctrl_port, reg);
-	reg |= CCKCTRL_LCLKEN | CCKCTRL_OCLKEN;
-	out_be32(cckctrl_port, reg);
-	reg |= CCKCTRL_CRST;
-	out_be32(cckctrl_port, reg);
-
-	for (;;) {
-		reg = in_be32(cckctrl_port);
-		if (reg & CCKCTRL_CRST)
-			break;
-		udelay(5000);
-	}
-
-	reg |= CCKCTRL_ATARESET;
-	out_be32(cckctrl_port, reg);
-	out_be32(ecmode_port, ECMODE_VALUE);
-	out_be32(mode_port, MODE_JCUSFEN);
-	out_be32(intmask_port, INTMASK_MSK);
-
-	if (in_be32(dmastatus_port) & QCHSD_STPDIAG) {
-		printk(KERN_WARNING "%s: failed to detect 80c cable. (PDIAG# is high)\n", DRV_NAME);
-		return -EIO;
-	}
-
-	return 0;
-}
-
-/**
- *	scc_setup_ports - initialize ioaddr with SCC PATA port offsets.
- *	@ioaddr: IO address structure to be initialized
- *	@base: base address of BMID region
- */
-
-static void scc_setup_ports (struct ata_ioports *ioaddr, void __iomem *base)
-{
-	ioaddr->cmd_addr = base + SCC_REG_CMD_ADDR;
-	ioaddr->altstatus_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
-	ioaddr->ctl_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
-	ioaddr->bmdma_addr = base;
-	ioaddr->data_addr = ioaddr->cmd_addr + SCC_REG_DATA;
-	ioaddr->error_addr = ioaddr->cmd_addr + SCC_REG_ERR;
-	ioaddr->feature_addr = ioaddr->cmd_addr + SCC_REG_FEATURE;
-	ioaddr->nsect_addr = ioaddr->cmd_addr + SCC_REG_NSECT;
-	ioaddr->lbal_addr = ioaddr->cmd_addr + SCC_REG_LBAL;
-	ioaddr->lbam_addr = ioaddr->cmd_addr + SCC_REG_LBAM;
-	ioaddr->lbah_addr = ioaddr->cmd_addr + SCC_REG_LBAH;
-	ioaddr->device_addr = ioaddr->cmd_addr + SCC_REG_DEVICE;
-	ioaddr->status_addr = ioaddr->cmd_addr + SCC_REG_STATUS;
-	ioaddr->command_addr = ioaddr->cmd_addr + SCC_REG_CMD;
-}
-
-static int scc_host_init(struct ata_host *host)
-{
-	struct pci_dev *pdev = to_pci_dev(host->dev);
-	int rc;
-
-	rc = scc_reset_controller(host);
-	if (rc)
-		return rc;
-
-	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
-	if (rc)
-		return rc;
-	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
-	if (rc)
-		return rc;
-
-	scc_setup_ports(&host->ports[0]->ioaddr, host->iomap[SCC_BMID_BAR]);
-
-	pci_set_master(pdev);
-
-	return 0;
-}
-
-/**
- *	scc_init_one - Register SCC PATA device with kernel services
- *	@pdev: PCI device to register
- *	@ent: Entry in scc_pci_tbl matching with @pdev
- *
- *	LOCKING:
- *	Inherited from PCI layer (may sleep).
- *
- *	RETURNS:
- *	Zero on success, or -ERRNO value.
- */
-
-static int scc_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
-{
-	unsigned int board_idx = (unsigned int) ent->driver_data;
-	const struct ata_port_info *ppi[] = { &scc_port_info[board_idx], NULL };
-	struct ata_host *host;
-	int rc;
-
-	ata_print_version_once(&pdev->dev, DRV_VERSION);
-
-	host = ata_host_alloc_pinfo(&pdev->dev, ppi, 1);
-	if (!host)
-		return -ENOMEM;
-
-	rc = pcim_enable_device(pdev);
-	if (rc)
-		return rc;
-
-	rc = pcim_iomap_regions(pdev, (1 << SCC_CTRL_BAR) | (1 << SCC_BMID_BAR), DRV_NAME);
-	if (rc == -EBUSY)
-		pcim_pin_device(pdev);
-	if (rc)
-		return rc;
-	host->iomap = pcim_iomap_table(pdev);
-
-	ata_port_pbar_desc(host->ports[0], SCC_CTRL_BAR, -1, "ctrl");
-	ata_port_pbar_desc(host->ports[0], SCC_BMID_BAR, -1, "bmid");
-
-	rc = scc_host_init(host);
-	if (rc)
-		return rc;
-
-	return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
-				 IRQF_SHARED, &scc_sht);
-}
-
-static struct pci_driver scc_pci_driver = {
-	.name			= DRV_NAME,
-	.id_table		= scc_pci_tbl,
-	.probe			= scc_init_one,
-	.remove			= ata_pci_remove_one,
-#ifdef CONFIG_PM_SLEEP
-	.suspend		= ata_pci_device_suspend,
-	.resume			= ata_pci_device_resume,
-#endif
-};
-
-module_pci_driver(scc_pci_driver);
-
-MODULE_AUTHOR("Toshiba corp");
-MODULE_DESCRIPTION("SCSI low-level driver for Toshiba SCC PATA controller");
-MODULE_LICENSE("GPL");
-MODULE_DEVICE_TABLE(pci, scc_pci_tbl);
-MODULE_VERSION(DRV_VERSION);