[libata] Add a bunch of PATA drivers.

The vast majority of drivers and changes are from Alan Cox.  Albert Lee
contributed and maintains pata_pdc2027x.  Adrian Bunk, Andrew Morton,
and Tejun Heo contributed various minor fixes and updates.

Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 597 insertions, 0 deletions

diff --git a/drivers/ata/pata_hpt3x2n.c b/drivers/ata/pata_hpt3x2n.c
new file mode 100644
index 0000000..40fcda6
--- /dev/null
+++ b/drivers/ata/pata_hpt3x2n.c
@@ -0,0 +1,597 @@
+/*
+ * Libata driver for the highpoint 372N and 302N UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c		Version 0.36	April 25, 2003
+ *
+ * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003		Red Hat Inc
+ *
+ *
+ * TODO
+ *	371N
+ *	Work out best PLL policy
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME	"pata_hpt3x2n"
+#define DRV_VERSION	"0.3"
+
+enum {
+	HPT_PCI_FAST	=	(1 << 31),
+	PCI66		=	(1 << 1),
+	USE_DPLL	=	(1 << 0)
+};
+
+struct hpt_clock {
+	u8	xfer_speed;
+	u32	timing;
+};
+
+struct hpt_chip {
+	const char *name;
+	struct hpt_clock *clocks[3];
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
+ *        during task file register access.
+ * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
+ *        xfer.
+ * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ *        register access.
+ * 28     UDMA enable
+ * 29     DMA enable
+ * 30     PIO_MST enable. if set, the chip is in bus master mode during
+ *        PIO.
+ * 31     FIFO enable.
+ */
+ 
+/* 66MHz DPLL clocks */
+
+static struct hpt_clock hpt3x2n_clocks[] = {
+	{	XFER_UDMA_7,	0x1c869c62	},
+	{	XFER_UDMA_6,	0x1c869c62	},
+	{	XFER_UDMA_5,	0x1c8a9c62	},
+	{	XFER_UDMA_4,	0x1c8a9c62	},
+	{	XFER_UDMA_3,	0x1c8e9c62	},
+	{	XFER_UDMA_2,	0x1c929c62	},
+	{	XFER_UDMA_1,	0x1c9a9c62	},
+	{	XFER_UDMA_0,	0x1c829c62	},
+
+	{	XFER_MW_DMA_2,	0x2c829c62	},
+	{	XFER_MW_DMA_1,	0x2c829c66	},
+	{	XFER_MW_DMA_0,	0x2c829d2c	},
+
+	{	XFER_PIO_4,	0x0c829c62	},
+	{	XFER_PIO_3,	0x0c829c84	},
+	{	XFER_PIO_2,	0x0c829ca6	},
+	{	XFER_PIO_1,	0x0d029d26	},
+	{	XFER_PIO_0,	0x0d029d5e	},
+	{	0,		0x0d029d5e	}
+};
+
+/**
+ *	hpt3x2n_find_mode	-	reset the hpt3x2n bus
+ *	@ap: ATA port
+ *	@speed: transfer mode
+ *
+ *	Return the 32bit register programming information for this channel
+ *	that matches the speed provided. For the moment the clocks table
+ *	is hard coded but easy to change. This will be needed if we use
+ *	different DPLLs
+ */
+ 
+static u32 hpt3x2n_find_mode(struct ata_port *ap, int speed)
+{
+	struct hpt_clock *clocks = hpt3x2n_clocks;
+	
+	while(clocks->xfer_speed) {
+		if (clocks->xfer_speed == speed)
+			return clocks->timing;
+		clocks++;
+	}
+	BUG();
+	return 0xffffffffU;	/* silence compiler warning */
+}
+
+/**
+ *	hpt3x2n_pre_reset	-	reset the hpt3x2n bus
+ *	@ap: ATA port to reset
+ *
+ *	Perform the initial reset handling for the 3x2n series controllers.
+ *	Reset the hardware and state machine, obtain the cable type.
+ */
+ 
+static int hpt3xn_pre_reset(struct ata_port *ap)
+{
+	u8 scr2, ata66;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	
+	pci_read_config_byte(pdev, 0x5B, &scr2);
+	pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+	/* Cable register now active */
+	pci_read_config_byte(pdev, 0x5A, &ata66);
+	/* Restore state */
+	pci_write_config_byte(pdev, 0x5B, scr2);
+	
+	if (ata66 & (1 << ap->port_no))
+		ap->cbl = ATA_CBL_PATA40;
+	else
+		ap->cbl = ATA_CBL_PATA80;
+
+	/* Reset the state machine */
+	pci_write_config_byte(pdev, 0x50, 0x37); 
+	pci_write_config_byte(pdev, 0x54, 0x37); 
+	udelay(100);
+
+	return ata_std_prereset(ap);
+}
+	
+/**
+ *	hpt3x2n_error_handler	-	probe the hpt3x2n bus
+ *	@ap: ATA port to reset
+ *
+ *	Perform the probe reset handling for the 3x2N
+ */
+ 
+static void hpt3x2n_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, hpt3xn_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+				     
+/**
+ *	hpt3x2n_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup. 
+ */
+ 
+static void hpt3x2n_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg;
+	u32 mode;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+	
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x07;
+	pci_write_config_byte(pdev, addr2, fast);
+	
+	pci_read_config_dword(pdev, addr1, &reg);
+	mode = hpt3x2n_find_mode(ap, adev->pio_mode);
+	mode &= ~0x8000000;	/* No FIFO in PIO */
+	mode &= ~0x30070000;	/* Leave config bits alone */
+	reg &= 0x30070000;	/* Strip timing bits */
+	pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *	hpt3x2n_set_dmamode		-	DMA timing setup
+ *	@ap: ATA interface
+ *	@adev: Device being configured
+ *
+ *	Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *	PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+ 
+static void hpt3x2n_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg;
+	u32 mode;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+	
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x07;
+	pci_write_config_byte(pdev, addr2, fast);
+	
+	pci_read_config_dword(pdev, addr1, &reg);
+	mode = hpt3x2n_find_mode(ap, adev->dma_mode);
+	mode |= 0x8000000;	/* FIFO in MWDMA or UDMA */
+	mode &= ~0xC0000000;	/* Leave config bits alone */
+	reg &= 0xC0000000;	/* Strip timing bits */
+	pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *	hpt3x2n_bmdma_end		-	DMA engine stop
+ *	@qc: ATA command
+ *
+ *	Clean up after the HPT3x2n and later DMA engine
+ */
+ 
+static void hpt3x2n_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int mscreg = 0x50 + 2 * ap->port_no;
+	u8 bwsr_stat, msc_stat;
+	
+	pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+	pci_read_config_byte(pdev, mscreg, &msc_stat);
+	if (bwsr_stat & (1 << ap->port_no))
+		pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+	ata_bmdma_stop(qc);
+}
+
+/**
+ *	hpt3x2n_set_clock	-	clock control
+ *	@ap: ATA port
+ *	@source: 0x21 or 0x23 for PLL or PCI sourced clock
+ *
+ *	Switch the ATA bus clock between the PLL and PCI clock sources
+ *	while correctly isolating the bus and resetting internal logic
+ *
+ *	We must use the DPLL for
+ *	-	writing
+ *	-	second channel UDMA7 (SATA ports) or higher
+ *	-	66MHz PCI
+ *	
+ *	or we will underclock the device and get reduced performance.
+ */
+ 
+static void hpt3x2n_set_clock(struct ata_port *ap, int source)
+{
+	unsigned long bmdma = ap->ioaddr.bmdma_addr;
+	
+	/* Tristate the bus */
+	outb(0x80, bmdma+0x73);
+	outb(0x80, bmdma+0x77);
+	
+	/* Switch clock and reset channels */
+	outb(source, bmdma+0x7B);
+	outb(0xC0, bmdma+0x79);
+	
+	/* Reset state machines */
+	outb(0x37, bmdma+0x70);
+	outb(0x37, bmdma+0x74);
+	
+	/* Complete reset */
+	outb(0x00, bmdma+0x79);
+	
+	/* Reconnect channels to bus */
+	outb(0x00, bmdma+0x73);
+	outb(0x00, bmdma+0x77);
+}
+
+/* Check if our partner interface is busy */
+
+static int hpt3x2n_pair_idle(struct ata_port *ap)
+{
+	struct ata_host *host = ap->host;
+	struct ata_port *pair = host->ports[ap->port_no ^ 1];
+	
+	if (pair->hsm_task_state == HSM_ST_IDLE)
+		return 1;
+	return 0;
+}
+
+static int hpt3x2n_use_dpll(struct ata_port *ap, int reading)
+{
+	long flags = (long)ap->host->private_data;
+	/* See if we should use the DPLL */
+	if (reading == 0)
+		return USE_DPLL;	/* Needed for write */
+	if (flags & PCI66)
+		return USE_DPLL;	/* Needed at 66Mhz */
+	return 0;	
+}
+
+static unsigned int hpt3x2n_qc_issue_prot(struct ata_queued_cmd *qc)
+{
+	struct ata_taskfile *tf = &qc->tf;
+	struct ata_port *ap = qc->ap;
+	int flags = (long)ap->host->private_data;
+	
+	if (hpt3x2n_pair_idle(ap)) {
+		int dpll = hpt3x2n_use_dpll(ap, (tf->flags & ATA_TFLAG_WRITE));
+		if ((flags & USE_DPLL) != dpll) {
+			if (dpll == 1)
+				hpt3x2n_set_clock(ap, 0x21);
+			else
+				hpt3x2n_set_clock(ap, 0x23);
+		}
+	}
+	return ata_qc_issue_prot(qc);
+}
+
+static struct scsi_host_template hpt3x2n_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.max_sectors		= ATA_MAX_SECTORS,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.bios_param		= ata_std_bios_param,
+};
+
+/*
+ *	Configuration for HPT3x2n.
+ */
+ 
+static struct ata_port_operations hpt3x2n_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= hpt3x2n_set_piomode,
+	.set_dmamode	= hpt3x2n_set_dmamode,
+	.mode_filter	= ata_pci_default_filter,
+	
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= hpt3x2n_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= ata_bmdma_start,
+	.bmdma_stop	= hpt3x2n_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= hpt3x2n_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};	
+
+/**
+ *	hpt3xn_calibrate_dpll		-	Calibrate the DPLL loop
+ *	@dev: PCI device 
+ *
+ *	Perform a calibration cycle on the HPT3xN DPLL. Returns 1 if this
+ *	succeeds
+ */
+
+static int hpt3xn_calibrate_dpll(struct pci_dev *dev)
+{
+	u8 reg5b;
+	u32 reg5c;
+	int tries;
+ 
+	for(tries = 0; tries < 0x5000; tries++) {
+		udelay(50);
+		pci_read_config_byte(dev, 0x5b, &reg5b);
+		if (reg5b & 0x80) {
+			/* See if it stays set */
+			for(tries = 0; tries < 0x1000; tries ++) {
+				pci_read_config_byte(dev, 0x5b, &reg5b);
+				/* Failed ? */
+				if ((reg5b & 0x80) == 0)
+					return 0;
+			}
+			/* Turn off tuning, we have the DPLL set */
+			pci_read_config_dword(dev, 0x5c, &reg5c);
+			pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
+			return 1;
+		}
+	}
+	/* Never went stable */
+	return 0;
+}
+
+static int hpt3x2n_pci_clock(struct pci_dev *pdev)
+{
+	unsigned long freq;
+	u32 fcnt;
+	
+	pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt);
+	if ((fcnt >> 12) != 0xABCDE) {
+		printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
+		return 33;	/* Not BIOS set */
+	}
+	fcnt &= 0x1FF;
+	
+	freq = (fcnt * 77) / 192;
+	
+	/* Clamp to bands */
+	if (freq < 40)
+		return 33;
+	if (freq < 45)
+		return 40;
+	if (freq < 55)
+		return 50;
+	return 66;
+}
+
+/**
+ *	hpt3x2n_init_one		-	Initialise an HPT37X/302
+ *	@dev: PCI device
+ *	@id: Entry in match table
+ *
+ *	Initialise an HPT3x2n device. There are some interesting complications
+ *	here. Firstly the chip may report 366 and be one of several variants.
+ *	Secondly all the timings depend on the clock for the chip which we must
+ *	detect and look up
+ *
+ *	This is the known chip mappings. It may be missing a couple of later
+ *	releases.
+ *
+ *	Chip version		PCI		Rev	Notes
+ *	HPT372			4 (HPT366)	5	Other driver
+ *	HPT372N			4 (HPT366)	6	UDMA133
+ *	HPT372			5 (HPT372)	1	Other driver
+ *	HPT372N			5 (HPT372)	2	UDMA133
+ *	HPT302			6 (HPT302)	*	Other driver
+ *	HPT302N			6 (HPT302)	> 1	UDMA133
+ *	HPT371			7 (HPT371)	*	Other driver
+ *	HPT371N			7 (HPT371)	> 1	UDMA133
+ *	HPT374			8 (HPT374)	*	Other driver
+ *	HPT372N			9 (HPT372N)	*	UDMA133
+ *
+ *	(1) UDMA133 support depends on the bus clock
+ *
+ *	To pin down		HPT371N
+ */
+ 
+static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	/* HPT372N and friends - UDMA133 */
+	static struct ata_port_info info = {
+		.sht = &hpt3x2n_sht,
+		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x7f,
+		.port_ops = &hpt3x2n_port_ops
+	};
+	struct ata_port_info *port_info[2];
+	struct ata_port_info *port = &info;
+
+	u8 irqmask;
+	u32 class_rev;
+	
+	unsigned int pci_mhz;
+	unsigned int f_low, f_high;
+	int adjust;
+	
+	pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
+	class_rev &= 0xFF;
+	
+	switch(dev->device) {
+		case PCI_DEVICE_ID_TTI_HPT366:
+			if (class_rev < 6)
+				return -ENODEV;
+			break;
+		case PCI_DEVICE_ID_TTI_HPT372:
+			/* 372N if rev >= 1*/
+			if (class_rev == 0)
+				return -ENODEV;
+			break;
+		case PCI_DEVICE_ID_TTI_HPT302:
+			if (class_rev < 2)
+				return -ENODEV;
+			break;
+		case PCI_DEVICE_ID_TTI_HPT372N:
+			break;
+		default:
+			printk(KERN_ERR "pata_hpt3x2n: PCI table is bogus please report (%d).\n", dev->device);
+			return -ENODEV;
+	}
+
+	/* Ok so this is a chip we support */
+
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+	pci_read_config_byte(dev, 0x5A, &irqmask);
+	irqmask &= ~0x10;
+	pci_write_config_byte(dev, 0x5a, irqmask);
+
+	/* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
+	   50 for UDMA100. Right now we always use 66 */
+	   
+	pci_mhz = hpt3x2n_pci_clock(dev);
+	
+	f_low = (pci_mhz * 48) / 66;	/* PCI Mhz for 66Mhz DPLL */
+	f_high = f_low + 2;		/* Tolerance */
+	
+	pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
+	/* PLL clock */
+	pci_write_config_byte(dev, 0x5B, 0x21);
+	
+	/* Unlike the 37x we don't try jiggling the frequency */
+	for(adjust = 0; adjust < 8; adjust++) {
+		if (hpt3xn_calibrate_dpll(dev))
+			break;
+		pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+	}
+	if (adjust == 8)
+		printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n");
+
+	/* Set our private data up. We only need a few flags so we use
+	   it directly */
+	port->private_data = NULL;
+	if (pci_mhz > 60)
+		port->private_data = (void *)PCI66;
+		
+	/* Now kick off ATA set up */
+	port_info[0] = port_info[1] = port;
+	return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt3x2n[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372N), },
+	{ 0, },
+};
+
+static struct pci_driver hpt3x2n_pci_driver = {
+        .name 		= DRV_NAME,
+	.id_table	= hpt3x2n,
+	.probe 		= hpt3x2n_init_one,
+	.remove		= ata_pci_remove_one
+};
+
+static int __init hpt3x2n_init(void)
+{
+	return pci_register_driver(&hpt3x2n_pci_driver);
+}
+
+
+static void __exit hpt3x2n_exit(void)
+{
+	pci_unregister_driver(&hpt3x2n_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT3x2n/30x");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt3x2n);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt3x2n_init);
+module_exit(hpt3x2n_exit);