[libata] Add a bunch of PATA drivers.

The vast majority of drivers and changes are from Alan Cox.  Albert Lee
contributed and maintains pata_pdc2027x.  Adrian Bunk, Andrew Morton,
and Tejun Heo contributed various minor fixes and updates.

Signed-off-by: Jeff Garzik <jeff@garzik.org>

1 files changed, 1257 insertions, 0 deletions

diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c
new file mode 100644
index 0000000..7c3da53
--- /dev/null
+++ b/drivers/ata/pata_hpt37x.c
@@ -0,0 +1,1257 @@
+/*
+ * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers.
+ *
+ * This driver is heavily based upon:
+ *
+ * linux/drivers/ide/pci/hpt366.c		Version 0.36	April 25, 2003
+ *
+ * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
+ * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
+ * Portions Copyright (C) 2003		Red Hat Inc
+ *
+ * TODO
+ *	PLL mode
+ *	Look into engine reset on timeout errors. Should not be
+ *		required.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME	"pata_hpt37x"
+#define DRV_VERSION	"0.5"
+
+struct hpt_clock {
+	u8	xfer_speed;
+	u32	timing;
+};
+
+struct hpt_chip {
+	const char *name;
+	unsigned int base;
+	struct hpt_clock const *clocks[4];
+};
+
+/* key for bus clock timings
+ * bit
+ * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
+ *        DMA. cycles = value + 1
+ * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
+ *        register access.
+ * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
+ *        during task file register access.
+ * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
+ *        xfer.
+ * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
+ *        register access.
+ * 28     UDMA enable
+ * 29     DMA enable
+ * 30     PIO_MST enable. if set, the chip is in bus master mode during
+ *        PIO.
+ * 31     FIFO enable.
+ */
+
+/* from highpoint documentation. these are old values */
+static const struct hpt_clock hpt370_timings_33[] = {
+/*	{	XFER_UDMA_5,	0x1A85F442,	0x16454e31	}, */
+	{	XFER_UDMA_5,	0x16454e31	},
+	{	XFER_UDMA_4,	0x16454e31	},
+	{	XFER_UDMA_3,	0x166d4e31	},
+	{	XFER_UDMA_2,	0x16494e31	},
+	{	XFER_UDMA_1,	0x164d4e31	},
+	{	XFER_UDMA_0,	0x16514e31	},
+
+	{	XFER_MW_DMA_2,	0x26514e21	},
+	{	XFER_MW_DMA_1,	0x26514e33	},
+	{	XFER_MW_DMA_0,	0x26514e97	},
+
+	{	XFER_PIO_4,	0x06514e21	},
+	{	XFER_PIO_3,	0x06514e22	},
+	{	XFER_PIO_2,	0x06514e33	},
+	{	XFER_PIO_1,	0x06914e43	},
+	{	XFER_PIO_0,	0x06914e57	},
+	{	0,		0x06514e57	}
+};
+
+static const struct hpt_clock hpt370_timings_66[] = {
+	{	XFER_UDMA_5,	0x14846231	},
+	{	XFER_UDMA_4,	0x14886231	},
+	{	XFER_UDMA_3,	0x148c6231	},
+	{	XFER_UDMA_2,	0x148c6231	},
+	{	XFER_UDMA_1,	0x14906231	},
+	{	XFER_UDMA_0,	0x14986231	},
+
+	{	XFER_MW_DMA_2,	0x26514e21	},
+	{	XFER_MW_DMA_1,	0x26514e33	},
+	{	XFER_MW_DMA_0,	0x26514e97	},
+
+	{	XFER_PIO_4,	0x06514e21	},
+	{	XFER_PIO_3,	0x06514e22	},
+	{	XFER_PIO_2,	0x06514e33	},
+	{	XFER_PIO_1,	0x06914e43	},
+	{	XFER_PIO_0,	0x06914e57	},
+	{	0,		0x06514e57	}
+};
+
+/* these are the current (4 sep 2001) timings from highpoint */
+static const struct hpt_clock hpt370a_timings_33[] = {
+	{	XFER_UDMA_5,	0x12446231	},
+	{	XFER_UDMA_4,	0x12446231	},
+	{	XFER_UDMA_3,	0x126c6231	},
+	{	XFER_UDMA_2,	0x12486231	},
+	{	XFER_UDMA_1,	0x124c6233	},
+	{	XFER_UDMA_0,	0x12506297	},
+
+	{	XFER_MW_DMA_2,	0x22406c31	},
+	{	XFER_MW_DMA_1,	0x22406c33	},
+	{	XFER_MW_DMA_0,	0x22406c97	},
+
+	{	XFER_PIO_4,	0x06414e31	},
+	{	XFER_PIO_3,	0x06414e42	},
+	{	XFER_PIO_2,	0x06414e53	},
+	{	XFER_PIO_1,	0x06814e93	},
+	{	XFER_PIO_0,	0x06814ea7	},
+	{	0,		0x06814ea7	}
+};
+
+/* 2x 33MHz timings */
+static const struct hpt_clock hpt370a_timings_66[] = {
+	{	XFER_UDMA_5,	0x1488e673	},
+	{	XFER_UDMA_4,	0x1488e673	},
+	{	XFER_UDMA_3,	0x1498e673	},
+	{	XFER_UDMA_2,	0x1490e673	},
+	{	XFER_UDMA_1,	0x1498e677	},
+	{	XFER_UDMA_0,	0x14a0e73f	},
+
+	{	XFER_MW_DMA_2,	0x2480fa73	},
+	{	XFER_MW_DMA_1,	0x2480fa77	}, 
+	{	XFER_MW_DMA_0,	0x2480fb3f	},
+
+	{	XFER_PIO_4,	0x0c82be73	},
+	{	XFER_PIO_3,	0x0c82be95	},
+	{	XFER_PIO_2,	0x0c82beb7	},
+	{	XFER_PIO_1,	0x0d02bf37	},
+	{	XFER_PIO_0,	0x0d02bf5f	},
+	{	0,		0x0d02bf5f	}
+};
+
+static const struct hpt_clock hpt370a_timings_50[] = {
+	{	XFER_UDMA_5,	0x12848242	},
+	{	XFER_UDMA_4,	0x12ac8242	},
+	{	XFER_UDMA_3,	0x128c8242	},
+	{	XFER_UDMA_2,	0x120c8242	},
+	{	XFER_UDMA_1,	0x12148254	},
+	{	XFER_UDMA_0,	0x121882ea	},
+
+	{	XFER_MW_DMA_2,	0x22808242	},
+	{	XFER_MW_DMA_1,	0x22808254	},
+	{	XFER_MW_DMA_0,	0x228082ea	},
+
+	{	XFER_PIO_4,	0x0a81f442	},
+	{	XFER_PIO_3,	0x0a81f443	},
+	{	XFER_PIO_2,	0x0a81f454	},
+	{	XFER_PIO_1,	0x0ac1f465	},
+	{	XFER_PIO_0,	0x0ac1f48a	},
+	{	0,		0x0ac1f48a	}
+};
+
+static const struct hpt_clock hpt372_timings_33[] = {
+	{	XFER_UDMA_6,	0x1c81dc62	},
+	{	XFER_UDMA_5,	0x1c6ddc62	},
+	{	XFER_UDMA_4,	0x1c8ddc62	},
+	{	XFER_UDMA_3,	0x1c8edc62	},	/* checkme */
+	{	XFER_UDMA_2,	0x1c91dc62	},
+	{	XFER_UDMA_1,	0x1c9adc62	},	/* checkme */
+	{	XFER_UDMA_0,	0x1c82dc62	},	/* checkme */
+
+	{	XFER_MW_DMA_2,	0x2c829262	},
+	{	XFER_MW_DMA_1,	0x2c829266	},	/* checkme */
+	{	XFER_MW_DMA_0,	0x2c82922e	},	/* checkme */
+
+	{	XFER_PIO_4,	0x0c829c62	},
+	{	XFER_PIO_3,	0x0c829c84	},
+	{	XFER_PIO_2,	0x0c829ca6	},
+	{	XFER_PIO_1,	0x0d029d26	},
+	{	XFER_PIO_0,	0x0d029d5e	},
+	{	0,		0x0d029d5e	}
+};
+
+static const struct hpt_clock hpt372_timings_50[] = {
+	{	XFER_UDMA_5,	0x12848242	},
+	{	XFER_UDMA_4,	0x12ac8242	},
+	{	XFER_UDMA_3,	0x128c8242	},
+	{	XFER_UDMA_2,	0x120c8242	},
+	{	XFER_UDMA_1,	0x12148254	},
+	{	XFER_UDMA_0,	0x121882ea	},
+
+	{	XFER_MW_DMA_2,	0x22808242	},
+	{	XFER_MW_DMA_1,	0x22808254	},
+	{	XFER_MW_DMA_0,	0x228082ea	},
+
+	{	XFER_PIO_4,	0x0a81f442	},
+	{	XFER_PIO_3,	0x0a81f443	},
+	{	XFER_PIO_2,	0x0a81f454	},
+	{	XFER_PIO_1,	0x0ac1f465	},
+	{	XFER_PIO_0,	0x0ac1f48a	},
+	{	0,		0x0a81f443	}
+};
+
+static const struct hpt_clock hpt372_timings_66[] = {
+	{	XFER_UDMA_6,	0x1c869c62	},
+	{	XFER_UDMA_5,	0x1cae9c62	},
+	{	XFER_UDMA_4,	0x1c8a9c62	},
+	{	XFER_UDMA_3,	0x1c8e9c62	},
+	{	XFER_UDMA_2,	0x1c929c62	},
+	{	XFER_UDMA_1,	0x1c9a9c62	},
+	{	XFER_UDMA_0,	0x1c829c62	},
+
+	{	XFER_MW_DMA_2,	0x2c829c62	},
+	{	XFER_MW_DMA_1,	0x2c829c66	},
+	{	XFER_MW_DMA_0,	0x2c829d2e	},
+
+	{	XFER_PIO_4,	0x0c829c62	},
+	{	XFER_PIO_3,	0x0c829c84	},
+	{	XFER_PIO_2,	0x0c829ca6	},
+	{	XFER_PIO_1,	0x0d029d26	},
+	{	XFER_PIO_0,	0x0d029d5e	},
+	{	0,		0x0d029d26	}
+};
+
+static const struct hpt_clock hpt374_timings_33[] = {
+	{	XFER_UDMA_6,	0x12808242	},
+	{	XFER_UDMA_5,	0x12848242	},
+	{	XFER_UDMA_4,	0x12ac8242	},
+	{	XFER_UDMA_3,	0x128c8242	},
+	{	XFER_UDMA_2,	0x120c8242	},
+	{	XFER_UDMA_1,	0x12148254	},
+	{	XFER_UDMA_0,	0x121882ea	},
+
+	{	XFER_MW_DMA_2,	0x22808242	},
+	{	XFER_MW_DMA_1,	0x22808254	},
+	{	XFER_MW_DMA_0,	0x228082ea	},
+
+	{	XFER_PIO_4,	0x0a81f442	},
+	{	XFER_PIO_3,	0x0a81f443	},
+	{	XFER_PIO_2,	0x0a81f454	},
+	{	XFER_PIO_1,	0x0ac1f465	},
+	{	XFER_PIO_0,	0x0ac1f48a	},
+	{	0,		0x06814e93	}
+};
+
+static const struct hpt_chip hpt370 = {
+	"HPT370",
+	48,
+	{
+		hpt370_timings_33,
+		NULL,
+		NULL,
+		hpt370_timings_66
+	}
+};
+
+static const struct hpt_chip hpt370a = {
+	"HPT370A",
+	48,
+	{
+		hpt370a_timings_33,
+		NULL,
+		hpt370a_timings_50,
+		hpt370a_timings_66
+	}
+};
+
+static const struct hpt_chip hpt372 = {
+	"HPT372",
+	55,
+	{
+		hpt372_timings_33,
+		NULL,
+		hpt372_timings_50,
+		hpt372_timings_66
+	}
+};
+
+static const struct hpt_chip hpt302 = {
+	"HPT302",
+	66,
+	{
+		hpt372_timings_33,
+		NULL,
+		hpt372_timings_50,
+		hpt372_timings_66
+	}
+};
+
+static const struct hpt_chip hpt371 = {
+	"HPT371",
+	66,
+	{
+		hpt372_timings_33,
+		NULL,
+		hpt372_timings_50,
+		hpt372_timings_66
+	}
+};
+
+static const struct hpt_chip hpt372a = {
+	"HPT372A",
+	66,
+	{
+		hpt372_timings_33,
+		NULL,
+		hpt372_timings_50,
+		hpt372_timings_66
+	}
+};
+
+static const struct hpt_chip hpt374 = {
+	"HPT374",
+	48,
+	{
+		hpt374_timings_33,
+		NULL,
+		NULL,
+		NULL
+	}
+};
+
+/**
+ *	hpt37x_find_mode	-	reset the hpt37x bus
+ *	@ap: ATA port
+ *	@speed: transfer mode
+ *
+ *	Return the 32bit register programming information for this channel
+ *	that matches the speed provided.
+ */
+ 
+static u32 hpt37x_find_mode(struct ata_port *ap, int speed)
+{
+	struct hpt_clock *clocks = ap->host->private_data;
+	
+	while(clocks->xfer_speed) {
+		if (clocks->xfer_speed == speed)
+			return clocks->timing;
+		clocks++;
+	}
+	BUG();
+	return 0xffffffffU;	/* silence compiler warning */
+}
+
+static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[])
+{
+	unsigned char model_num[40];
+	char *s;
+	unsigned int len;
+	int i = 0;
+
+	ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS,
+			  sizeof(model_num));
+	s = &model_num[0];
+	len = strnlen(s, sizeof(model_num));
+
+	/* ATAPI specifies that empty space is blank-filled; remove blanks */
+	while ((len > 0) && (s[len - 1] == ' ')) {
+		len--;
+		s[len] = 0;
+	}
+
+	while(list[i] != NULL) {
+		if (!strncmp(list[i], s, len)) {
+			printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n", 
+				modestr, list[i]);
+			return 1;
+		}
+		i++;
+	}
+	return 0;
+}
+
+static const char *bad_ata33[] = {
+	"Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
+	"Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
+	"Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
+	"Maxtor 90510D4",
+	"Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
+	"Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
+	"Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
+	NULL
+};
+
+static const char *bad_ata100_5[] = {
+	"IBM-DTLA-307075",
+	"IBM-DTLA-307060",
+	"IBM-DTLA-307045",
+	"IBM-DTLA-307030",
+	"IBM-DTLA-307020",
+	"IBM-DTLA-307015",
+	"IBM-DTLA-305040",
+	"IBM-DTLA-305030",
+	"IBM-DTLA-305020",
+	"IC35L010AVER07-0",
+	"IC35L020AVER07-0",
+	"IC35L030AVER07-0",
+	"IC35L040AVER07-0",
+	"IC35L060AVER07-0",
+	"WDC AC310200R",
+	NULL
+};
+
+/**
+ *	hpt370_filter	-	mode selection filter
+ *	@ap: ATA interface
+ *	@adev: ATA device
+ *
+ *	Block UDMA on devices that cause trouble with this controller.
+ */
+ 
+static unsigned long hpt370_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+	if (adev->class != ATA_DEV_ATA) {
+		if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
+			mask &= ~ATA_MASK_UDMA;
+		if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+			mask &= ~(0x1F << ATA_SHIFT_UDMA);
+	}
+	return ata_pci_default_filter(ap, adev, mask);
+}
+
+/**
+ *	hpt370a_filter	-	mode selection filter
+ *	@ap: ATA interface
+ *	@adev: ATA device
+ *
+ *	Block UDMA on devices that cause trouble with this controller.
+ */
+ 
+static unsigned long hpt370a_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
+{
+	if (adev->class != ATA_DEV_ATA) {
+		if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5))
+			mask &= ~ (0x1F << ATA_SHIFT_UDMA);
+	}
+	return ata_pci_default_filter(ap, adev, mask);
+}
+	
+/**
+ *	hpt37x_pre_reset	-	reset the hpt37x bus
+ *	@ap: ATA port to reset
+ *
+ *	Perform the initial reset handling for the 370/372 and 374 func 0
+ */
+ 
+static int hpt37x_pre_reset(struct ata_port *ap)
+{
+	u8 scr2, ata66;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	
+	pci_read_config_byte(pdev, 0x5B, &scr2);
+	pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01);
+	/* Cable register now active */
+	pci_read_config_byte(pdev, 0x5A, &ata66);
+	/* Restore state */
+	pci_write_config_byte(pdev, 0x5B, scr2);
+	
+	if (ata66 & (1 << ap->port_no))
+		ap->cbl = ATA_CBL_PATA40;
+	else
+		ap->cbl = ATA_CBL_PATA80;
+
+	/* Reset the state machine */
+	pci_write_config_byte(pdev, 0x50, 0x37); 
+	pci_write_config_byte(pdev, 0x54, 0x37); 
+	udelay(100);
+	
+	return ata_std_prereset(ap);
+}
+
+/**
+ *	hpt37x_error_handler	-	reset the hpt374
+ *	@ap: ATA port to reset
+ *
+ *	Perform probe for HPT37x, except for HPT374 channel 2
+ */
+ 
+static void hpt37x_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+static int hpt374_pre_reset(struct ata_port *ap)
+{
+	u16 mcr3, mcr6;
+	u8 ata66;
+	
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	/* Do the extra channel work */
+	pci_read_config_word(pdev, 0x52, &mcr3);
+	pci_read_config_word(pdev, 0x56, &mcr6);
+	/* Set bit 15 of 0x52 to enable TCBLID as input
+	   Set bit 15 of 0x56 to enable FCBLID as input
+	 */
+	pci_write_config_word(pdev, 0x52, mcr3 | 0x8000);
+	pci_write_config_word(pdev, 0x56, mcr6 | 0x8000);
+	pci_read_config_byte(pdev, 0x5A, &ata66);
+	/* Reset TCBLID/FCBLID to output */
+	pci_write_config_word(pdev, 0x52, mcr3);
+	pci_write_config_word(pdev, 0x56, mcr6);
+	
+	if (ata66 & (1 << ap->port_no))
+		ap->cbl = ATA_CBL_PATA40;
+	else
+		ap->cbl = ATA_CBL_PATA80;
+
+	/* Reset the state machine */
+	pci_write_config_byte(pdev, 0x50, 0x37); 
+	pci_write_config_byte(pdev, 0x54, 0x37); 
+	udelay(100);
+	
+	return ata_std_prereset(ap);
+}
+
+/**
+ *	hpt374_error_handler	-	reset the hpt374
+ *	@classes:
+ *
+ *	The 374 cable detect is a little different due to the extra
+ *	channels. The function 0 channels work like usual but function 1
+ *	is special
+ */
+ 
+static void hpt374_error_handler(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+		
+	if (!(PCI_FUNC(pdev->devfn) & 1))
+		hpt37x_error_handler(ap);
+	else
+		ata_bmdma_drive_eh(ap, hpt374_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
+}
+
+/**
+ *	hpt370_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup. 
+ */
+ 
+static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg;
+	u32 mode;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+	
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x02;
+	fast |= 0x01;
+	pci_write_config_byte(pdev, addr2, fast);
+	
+	pci_read_config_dword(pdev, addr1, &reg);
+	mode = hpt37x_find_mode(ap, adev->pio_mode);
+	mode &= ~0x8000000;	/* No FIFO in PIO */
+	mode &= ~0x30070000;	/* Leave config bits alone */
+	reg &= 0x30070000;	/* Strip timing bits */
+	pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *	hpt370_set_dmamode		-	DMA timing setup
+ *	@ap: ATA interface
+ *	@adev: Device being configured
+ *
+ *	Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *	PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+ 
+static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg;
+	u32 mode;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+	
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x02;
+	fast |= 0x01;
+	pci_write_config_byte(pdev, addr2, fast);
+	
+	pci_read_config_dword(pdev, addr1, &reg);
+	mode = hpt37x_find_mode(ap, adev->dma_mode);
+	mode |= 0x8000000;	/* FIFO in MWDMA or UDMA */
+	mode &= ~0xC0000000;	/* Leave config bits alone */
+	reg &= 0xC0000000;	/* Strip timing bits */
+	pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *	hpt370_bmdma_start		-	DMA engine begin
+ *	@qc: ATA command
+ *
+ *	The 370 and 370A want us to reset the DMA engine each time we
+ *	use it. The 372 and later are fine.
+ */
+ 
+static void hpt370_bmdma_start(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+	udelay(10);
+	ata_bmdma_start(qc);
+}
+
+/**
+ *	hpt370_bmdma_end		-	DMA engine stop
+ *	@qc: ATA command
+ *
+ *	Work around the HPT370 DMA engine.
+ */
+ 
+static void hpt370_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u8 dma_stat = inb(ap->ioaddr.bmdma_addr + 2);
+	u8 dma_cmd;
+	unsigned long bmdma = ap->ioaddr.bmdma_addr;
+	
+	if (dma_stat & 0x01) {
+		udelay(20);
+		dma_stat = inb(bmdma + 2);
+	}
+	if (dma_stat & 0x01) {
+		/* Clear the engine */
+		pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+		udelay(10);
+		/* Stop DMA */
+		dma_cmd = inb(bmdma );
+		outb(dma_cmd & 0xFE, bmdma);
+		/* Clear Error */
+		dma_stat = inb(bmdma + 2);
+		outb(dma_stat | 0x06 , bmdma + 2);
+		/* Clear the engine */
+		pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
+		udelay(10);
+	}
+	ata_bmdma_stop(qc);
+}
+
+/**
+ *	hpt372_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Perform PIO mode setup. 
+ */
+ 
+static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg;
+	u32 mode;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+	
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x07;
+	pci_write_config_byte(pdev, addr2, fast);
+	
+	pci_read_config_dword(pdev, addr1, &reg);
+	mode = hpt37x_find_mode(ap, adev->pio_mode);
+	
+	printk("Find mode for %d reports %X\n", adev->pio_mode, mode);
+	mode &= ~0x80000000;	/* No FIFO in PIO */
+	mode &= ~0x30070000;	/* Leave config bits alone */
+	reg &= 0x30070000;	/* Strip timing bits */
+	pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *	hpt372_set_dmamode		-	DMA timing setup
+ *	@ap: ATA interface
+ *	@adev: Device being configured
+ *
+ *	Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *	PIO, load the mode number and then set MWDMA or UDMA flag.
+ */
+ 
+static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 addr1, addr2;
+	u32 reg;
+	u32 mode;
+	u8 fast;
+
+	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
+	addr2 = 0x51 + 4 * ap->port_no;
+	
+	/* Fast interrupt prediction disable, hold off interrupt disable */
+	pci_read_config_byte(pdev, addr2, &fast);
+	fast &= ~0x07;
+	pci_write_config_byte(pdev, addr2, fast);
+	
+	pci_read_config_dword(pdev, addr1, &reg);
+	mode = hpt37x_find_mode(ap, adev->dma_mode);
+	printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode);
+	mode &= ~0xC0000000;	/* Leave config bits alone */
+	mode |= 0x80000000;	/* FIFO in MWDMA or UDMA */
+	reg &= 0xC0000000;	/* Strip timing bits */
+	pci_write_config_dword(pdev, addr1, reg | mode);
+}
+
+/**
+ *	hpt37x_bmdma_end		-	DMA engine stop
+ *	@qc: ATA command
+ *
+ *	Clean up after the HPT372 and later DMA engine
+ */
+ 
+static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	int mscreg = 0x50 + 2 * ap->port_no;
+	u8 bwsr_stat, msc_stat;
+	
+	pci_read_config_byte(pdev, 0x6A, &bwsr_stat);
+	pci_read_config_byte(pdev, mscreg, &msc_stat);
+	if (bwsr_stat & (1 << ap->port_no))
+		pci_write_config_byte(pdev, mscreg, msc_stat | 0x30);
+	ata_bmdma_stop(qc);
+}
+
+
+static struct scsi_host_template hpt37x_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.max_sectors		= ATA_MAX_SECTORS,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.bios_param		= ata_std_bios_param,
+};
+
+/*
+ *	Configuration for HPT370
+ */
+ 
+static struct ata_port_operations hpt370_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= hpt370_set_piomode,
+	.set_dmamode	= hpt370_set_dmamode,
+	.mode_filter	= hpt370_filter,
+	
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= hpt37x_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= hpt370_bmdma_start,
+	.bmdma_stop	= hpt370_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};	
+
+/*
+ *	Configuration for HPT370A. Close to 370 but less filters
+ */
+ 
+static struct ata_port_operations hpt370a_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= hpt370_set_piomode,
+	.set_dmamode	= hpt370_set_dmamode,
+	.mode_filter	= hpt370a_filter,
+	
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= hpt37x_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= hpt370_bmdma_start,
+	.bmdma_stop	= hpt370_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};	
+
+/*
+ *	Configuration for HPT372, HPT371, HPT302. Slightly different PIO
+ *	and DMA mode setting functionality.
+ */
+ 
+static struct ata_port_operations hpt372_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= hpt372_set_piomode,
+	.set_dmamode	= hpt372_set_dmamode,
+	.mode_filter	= ata_pci_default_filter,
+	
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= hpt37x_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= ata_bmdma_start,
+	.bmdma_stop	= hpt37x_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};	
+
+/*
+ *	Configuration for HPT374. Mode setting works like 372 and friends
+ *	but we have a different cable detection procedure.
+ */
+ 
+static struct ata_port_operations hpt374_port_ops = {
+	.port_disable	= ata_port_disable,
+	.set_piomode	= hpt372_set_piomode,
+	.set_dmamode	= hpt372_set_dmamode,
+	.mode_filter	= ata_pci_default_filter,
+	
+	.tf_load	= ata_tf_load,
+	.tf_read	= ata_tf_read,
+	.check_status 	= ata_check_status,
+	.exec_command	= ata_exec_command,
+	.dev_select 	= ata_std_dev_select,
+
+	.freeze		= ata_bmdma_freeze,
+	.thaw		= ata_bmdma_thaw,
+	.error_handler	= hpt374_error_handler,
+	.post_internal_cmd = ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup 	= ata_bmdma_setup,
+	.bmdma_start 	= ata_bmdma_start,
+	.bmdma_stop	= hpt37x_bmdma_stop,
+	.bmdma_status 	= ata_bmdma_status,
+
+	.qc_prep 	= ata_qc_prep,
+	.qc_issue	= ata_qc_issue_prot,
+	.eng_timeout	= ata_eng_timeout,
+	.data_xfer	= ata_pio_data_xfer,
+
+	.irq_handler	= ata_interrupt,
+	.irq_clear	= ata_bmdma_irq_clear,
+
+	.port_start	= ata_port_start,
+	.port_stop	= ata_port_stop,
+	.host_stop	= ata_host_stop
+};	
+
+/**
+ *	htp37x_clock_slot	-	Turn timing to PC clock entry
+ *	@freq: Reported frequency timing
+ *	@base: Base timing
+ *
+ *	Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50
+ *	and 3 for 66Mhz)
+ */
+ 
+static int hpt37x_clock_slot(unsigned int freq, unsigned int base)
+{
+	unsigned int f = (base * freq) / 192;	/* Mhz */
+	if (f < 40)
+		return 0;	/* 33Mhz slot */
+	if (f < 45)
+		return 1;	/* 40Mhz slot */
+	if (f < 55)
+		return 2;	/* 50Mhz slot */
+	return 3;		/* 60Mhz slot */
+}
+
+/**
+ *	hpt37x_calibrate_dpll		-	Calibrate the DPLL loop
+ *	@dev: PCI device 
+ *
+ *	Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this
+ *	succeeds
+ */
+
+static int hpt37x_calibrate_dpll(struct pci_dev *dev)
+{
+	u8 reg5b;
+	u32 reg5c;
+	int tries;
+ 
+	for(tries = 0; tries < 0x5000; tries++) {
+		udelay(50);
+		pci_read_config_byte(dev, 0x5b, &reg5b);
+		if (reg5b & 0x80) {
+			/* See if it stays set */
+			for(tries = 0; tries < 0x1000; tries ++) {
+				pci_read_config_byte(dev, 0x5b, &reg5b);
+				/* Failed ? */
+				if ((reg5b & 0x80) == 0)
+					return 0;
+			}
+			/* Turn off tuning, we have the DPLL set */
+			pci_read_config_dword(dev, 0x5c, &reg5c);
+			pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100);
+			return 1;
+		}
+	}
+	/* Never went stable */
+	return 0;
+}
+/**
+ *	hpt37x_init_one		-	Initialise an HPT37X/302
+ *	@dev: PCI device
+ *	@id: Entry in match table
+ *
+ *	Initialise an HPT37x device. There are some interesting complications
+ *	here. Firstly the chip may report 366 and be one of several variants.
+ *	Secondly all the timings depend on the clock for the chip which we must
+ *	detect and look up
+ *
+ *	This is the known chip mappings. It may be missing a couple of later
+ *	releases.
+ *
+ *	Chip version		PCI		Rev	Notes
+ *	HPT366			4 (HPT366)	0	Other driver
+ *	HPT366			4 (HPT366)	1	Other driver
+ *	HPT368			4 (HPT366)	2	Other driver
+ *	HPT370			4 (HPT366)	3	UDMA100
+ *	HPT370A			4 (HPT366)	4	UDMA100
+ *	HPT372			4 (HPT366)	5	UDMA133 (1)
+ *	HPT372N			4 (HPT366)	6	Other driver
+ *	HPT372A			5 (HPT372)	1	UDMA133 (1)
+ *	HPT372N			5 (HPT372)	2	Other driver
+ *	HPT302			6 (HPT302)	1	UDMA133
+ *	HPT302N			6 (HPT302)	2	Other driver
+ *	HPT371			7 (HPT371)	*	UDMA133
+ *	HPT374			8 (HPT374)	*	UDMA133 4 channel
+ *	HPT372N			9 (HPT372N)	*	Other driver
+ *
+ *	(1) UDMA133 support depends on the bus clock
+ */
+ 
+static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	/* HPT370 - UDMA100 */
+	static struct ata_port_info info_hpt370 = {
+		.sht = &hpt37x_sht,
+		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x3f,
+		.port_ops = &hpt370_port_ops
+	};
+	/* HPT370A - UDMA100 */
+	static struct ata_port_info info_hpt370a = {
+		.sht = &hpt37x_sht,
+		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x3f,
+		.port_ops = &hpt370a_port_ops
+	};
+	/* HPT371, 372 and friends - UDMA133 */
+	static struct ata_port_info info_hpt372 = {
+		.sht = &hpt37x_sht,
+		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x7f,
+		.port_ops = &hpt372_port_ops
+	};
+	/* HPT371, 372 and friends - UDMA100 at 50MHz clock */
+	static struct ata_port_info info_hpt372_50 = {
+		.sht = &hpt37x_sht,
+		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x3f,
+		.port_ops = &hpt372_port_ops
+	};
+	/* HPT374 - UDMA133 */
+	static struct ata_port_info info_hpt374 = {
+		.sht = &hpt37x_sht,
+		.flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST,
+		.pio_mask = 0x1f,
+		.mwdma_mask = 0x07,
+		.udma_mask = 0x7f,
+		.port_ops = &hpt374_port_ops
+	};
+
+	static const int MHz[4] = { 33, 40, 50, 66 };
+
+	struct ata_port_info *port_info[2];
+	struct ata_port_info *port;
+
+	u8 irqmask;
+	u32 class_rev;
+	u32 freq;
+
+	const struct hpt_chip *chip_table;
+	int clock_slot;
+
+	pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
+	class_rev &= 0xFF;
+	
+	if (dev->device == PCI_DEVICE_ID_TTI_HPT366) {
+		/* May be a later chip in disguise. Check */
+		/* Older chips are in the HPT366 driver. Ignore them */
+		if (class_rev < 3)
+			return -ENODEV;
+		/* N series chips have their own driver. Ignore */
+		if (class_rev == 6)
+			return -ENODEV;
+
+		switch(class_rev) {			
+			case 3:
+				port = &info_hpt370;
+				chip_table = &hpt370;
+				break;
+			case 4:
+				port = &info_hpt370a;
+				chip_table = &hpt370a;
+				break;
+			case 5:
+				port = &info_hpt372;
+				chip_table = &hpt372;
+				break;
+			default:
+				printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype please report (%d).\n", class_rev);
+				return -ENODEV;
+		}
+	} else {
+		switch(dev->device) {
+			case PCI_DEVICE_ID_TTI_HPT372:
+				/* 372N if rev >= 2*/
+				if (class_rev >= 2)
+					return -ENODEV;
+				port = &info_hpt372;
+				chip_table = &hpt372a;
+				break;
+			case PCI_DEVICE_ID_TTI_HPT302:
+				/* 302N if rev > 1 */
+				if (class_rev > 1)
+					return -ENODEV;
+				port = &info_hpt372;
+				/* Check this */
+				chip_table = &hpt302;
+				break;
+			case PCI_DEVICE_ID_TTI_HPT371:
+				port = &info_hpt372;
+				chip_table = &hpt371;
+				break;
+			case PCI_DEVICE_ID_TTI_HPT374:
+				chip_table = &hpt374;
+				port = &info_hpt374;
+				break;
+			default:
+				printk(KERN_ERR "pata_hpt37x: PCI table is bogus please report (%d).\n", dev->device);
+				return -ENODEV;
+		}
+	}
+	/* Ok so this is a chip we support */
+
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
+
+	pci_read_config_byte(dev, 0x5A, &irqmask);
+	irqmask &= ~0x10;
+	pci_write_config_byte(dev, 0x5a, irqmask);
+
+	/*
+	 * default to pci clock. make sure MA15/16 are set to output
+	 * to prevent drives having problems with 40-pin cables. Needed
+	 * for some drives such as IBM-DTLA which will not enter ready
+	 * state on reset when PDIAG is a input.
+	 */
+
+	pci_write_config_byte(dev, 0x5b, 0x23);	
+	
+	pci_read_config_dword(dev, 0x70, &freq);
+	if ((freq >> 12) != 0xABCDE) {
+		int i;
+		u8 sr;
+		u32 total = 0;
+		
+		printk(KERN_WARNING "pata_hpt37x: BIOS has not set timing clocks.\n");
+		
+		/* This is the process the HPT371 BIOS is reported to use */
+		for(i = 0; i < 128; i++) {
+			pci_read_config_byte(dev, 0x78, &sr);
+			total += sr;
+			udelay(15);
+		}
+		freq = total / 128;
+	}
+	freq &= 0x1FF;
+	
+	/*
+	 *	Turn the frequency check into a band and then find a timing
+	 *	table to match it.
+	 */
+	 
+	clock_slot = hpt37x_clock_slot(freq, chip_table->base);
+	if (chip_table->clocks[clock_slot] == NULL) {
+		/*
+		 *	We need to try PLL mode instead
+		 */
+		unsigned int f_low = (MHz[clock_slot] * chip_table->base) / 192;
+		unsigned int f_high = f_low + 2;
+		int adjust;
+		
+		for(adjust = 0; adjust < 8; adjust++) {
+			if (hpt37x_calibrate_dpll(dev))
+				break;
+			/* See if it'll settle at a fractionally different clock */
+			if ((adjust & 3) == 3) {
+				f_low --;
+				f_high ++;
+			}
+			pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
+		}
+		if (adjust == 8) {
+			printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n");
+			return -ENODEV;
+		}
+		/* Check if this works for all cases */
+		port->private_data = (void *)hpt370_timings_66;
+		
+		printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]);
+	} else {
+		port->private_data = (void *)chip_table->clocks[clock_slot];
+		/*
+		 *	Perform a final fixup. The 371 and 372 clock determines
+		 *	if UDMA133 is available.
+		 */
+	 
+		if (clock_slot == 2 && chip_table == &hpt372) {	/* 50Mhz */
+			printk(KERN_WARNING "pata_hpt37x: No UDMA133 support available with 50MHz bus clock.\n");
+			if (port == &info_hpt372)
+				port = &info_hpt372_50;
+			else BUG();
+		}
+		printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]);
+	}
+	port_info[0] = port_info[1] = port;	
+	/* Now kick off ATA set up */
+	return ata_pci_init_one(dev, port_info, 2);
+}
+
+static struct pci_device_id hpt37x[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374), },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), },
+	{ 0, },
+};
+
+static struct pci_driver hpt37x_pci_driver = {
+        .name 		= DRV_NAME,
+	.id_table	= hpt37x,
+	.probe 		= hpt37x_init_one,
+	.remove		= ata_pci_remove_one
+};
+
+static int __init hpt37x_init(void)
+{
+	return pci_register_driver(&hpt37x_pci_driver);
+}
+
+
+static void __exit hpt37x_exit(void)
+{
+	pci_unregister_driver(&hpt37x_pci_driver);
+}
+
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt37x);
+MODULE_VERSION(DRV_VERSION);
+
+module_init(hpt37x_init);
+module_exit(hpt37x_exit);