[ARM] pxa/saar: add support for the on-board smart panel LCD

Signed-off-by: Eric Miao <eric.miao@marvell.com>

1 files changed, 421 insertions, 0 deletions

diff --git a/arch/arm/mach-pxa/saar.c b/arch/arm/mach-pxa/saar.c
index e7ea91c..5d02a73 100644
--- a/arch/arm/mach-pxa/saar.c
+++ b/arch/arm/mach-pxa/saar.c
@@ -17,19 +17,44 @@
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/fb.h>
+#include <linux/i2c.h>
 #include <linux/smc91x.h>
+#include <linux/mfd/da903x.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <mach/hardware.h>
 #include <mach/pxa3xx-regs.h>
 #include <mach/mfp-pxa930.h>
+#include <mach/i2c.h>
+#include <mach/regs-lcd.h>
+#include <mach/pxafb.h>
 
 #include "devices.h"
 #include "generic.h"
 
+#define GPIO_LCD_RESET	(16)
+
 /* SAAR MFP configurations */
 static mfp_cfg_t saar_mfp_cfg[] __initdata = {
+	/* LCD */
+	GPIO23_LCD_DD0,
+	GPIO24_LCD_DD1,
+	GPIO25_LCD_DD2,
+	GPIO26_LCD_DD3,
+	GPIO27_LCD_DD4,
+	GPIO28_LCD_DD5,
+	GPIO29_LCD_DD6,
+	GPIO44_LCD_DD7,
+	GPIO21_LCD_CS,
+	GPIO22_LCD_VSYNC,
+	GPIO17_LCD_FCLK_RD,
+	GPIO18_LCD_LCLK_A0,
+	GPIO19_LCD_PCLK_WR,
+	GPIO16_GPIO, /* LCD reset */
+
 	/* Ethernet */
 	DF_nCS1_nCS3,
 	GPIO97_GPIO,
@@ -64,12 +89,408 @@ static struct platform_device smc91x_device = {
 	},
 };
 
+#if defined(CONFIG_FB_PXA) || (CONFIG_FB_PXA_MODULE)
+static uint16_t lcd_power_on[] = {
+	/* single frame */
+	SMART_CMD_NOOP,
+	SMART_CMD(0x00),
+	SMART_DELAY(0),
+
+	SMART_CMD_NOOP,
+	SMART_CMD(0x00),
+	SMART_DELAY(0),
+
+	SMART_CMD_NOOP,
+	SMART_CMD(0x00),
+	SMART_DELAY(0),
+
+	SMART_CMD_NOOP,
+	SMART_CMD(0x00),
+	SMART_DELAY(10),
+
+	/* calibration control */
+	SMART_CMD(0x00),
+	SMART_CMD(0xA4),
+	SMART_DAT(0x80),
+	SMART_DAT(0x01),
+	SMART_DELAY(150),
+
+	/*Power-On Init sequence*/
+	SMART_CMD(0x00),	/* output ctrl */
+	SMART_CMD(0x01),
+	SMART_DAT(0x01),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),	/* wave ctrl */
+	SMART_CMD(0x02),
+	SMART_DAT(0x07),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),
+	SMART_CMD(0x03),	/* entry mode */
+	SMART_DAT(0xD0),
+	SMART_DAT(0x30),
+	SMART_CMD(0x00),
+	SMART_CMD(0x08),	/* display ctrl 2 */
+	SMART_DAT(0x08),
+	SMART_DAT(0x08),
+	SMART_CMD(0x00),
+	SMART_CMD(0x09),	/* display ctrl 3 */
+	SMART_DAT(0x04),
+	SMART_DAT(0x2F),
+	SMART_CMD(0x00),
+	SMART_CMD(0x0A),	/* display ctrl 4 */
+	SMART_DAT(0x00),
+	SMART_DAT(0x08),
+	SMART_CMD(0x00),
+	SMART_CMD(0x0D),	/* Frame Marker position */
+	SMART_DAT(0x00),
+	SMART_DAT(0x08),
+	SMART_CMD(0x00),
+	SMART_CMD(0x60),	/* Driver output control */
+	SMART_DAT(0x27),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),
+	SMART_CMD(0x61),	/* Base image display control */
+	SMART_DAT(0x00),
+	SMART_DAT(0x01),
+	SMART_CMD(0x00),
+	SMART_CMD(0x30),	/* Y settings 30h-3Dh */
+	SMART_DAT(0x07),
+	SMART_DAT(0x07),
+	SMART_CMD(0x00),
+	SMART_CMD(0x31),
+	SMART_DAT(0x00),
+	SMART_DAT(0x07),
+	SMART_CMD(0x00),
+	SMART_CMD(0x32),	/* Timing(3), ASW HOLD=0.5CLK */
+	SMART_DAT(0x04),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),
+	SMART_CMD(0x33),	/* Timing(4), CKV ST=0CLK, CKV ED=1CLK */
+	SMART_DAT(0x03),
+	SMART_DAT(0x03),
+	SMART_CMD(0x00),
+	SMART_CMD(0x34),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),
+	SMART_CMD(0x35),
+	SMART_DAT(0x02),
+	SMART_DAT(0x05),
+	SMART_CMD(0x00),
+	SMART_CMD(0x36),
+	SMART_DAT(0x1F),
+	SMART_DAT(0x1F),
+	SMART_CMD(0x00),
+	SMART_CMD(0x37),
+	SMART_DAT(0x07),
+	SMART_DAT(0x07),
+	SMART_CMD(0x00),
+	SMART_CMD(0x38),
+	SMART_DAT(0x00),
+	SMART_DAT(0x07),
+	SMART_CMD(0x00),
+	SMART_CMD(0x39),
+	SMART_DAT(0x04),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),
+	SMART_CMD(0x3A),
+	SMART_DAT(0x03),
+	SMART_DAT(0x03),
+	SMART_CMD(0x00),
+	SMART_CMD(0x3B),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),
+	SMART_CMD(0x3C),
+	SMART_DAT(0x02),
+	SMART_DAT(0x05),
+	SMART_CMD(0x00),
+	SMART_CMD(0x3D),
+	SMART_DAT(0x1F),
+	SMART_DAT(0x1F),
+	SMART_CMD(0x00),	/* Display control 1 */
+	SMART_CMD(0x07),
+	SMART_DAT(0x00),
+	SMART_DAT(0x01),
+	SMART_CMD(0x00),	/* Power control 5 */
+	SMART_CMD(0x17),
+	SMART_DAT(0x00),
+	SMART_DAT(0x01),
+	SMART_CMD(0x00),	/* Power control 1 */
+	SMART_CMD(0x10),
+	SMART_DAT(0x10),
+	SMART_DAT(0xB0),
+	SMART_CMD(0x00),	/* Power control 2 */
+	SMART_CMD(0x11),
+	SMART_DAT(0x01),
+	SMART_DAT(0x30),
+	SMART_CMD(0x00),	/* Power control 3 */
+	SMART_CMD(0x12),
+	SMART_DAT(0x01),
+	SMART_DAT(0x9E),
+	SMART_CMD(0x00),	/* Power control 4 */
+	SMART_CMD(0x13),
+	SMART_DAT(0x17),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),	/* Power control 3 */
+	SMART_CMD(0x12),
+	SMART_DAT(0x01),
+	SMART_DAT(0xBE),
+	SMART_DELAY(100),
+
+	/* display mode : 240*320 */
+	SMART_CMD(0x00),	/* RAM address set(H) 0*/
+	SMART_CMD(0x20),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),	/* RAM address set(V)   4*/
+	SMART_CMD(0x21),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),	/* Start of Window RAM address set(H) 8*/
+	SMART_CMD(0x50),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00), 	/* End of Window RAM address set(H) 12*/
+	SMART_CMD(0x51),
+	SMART_DAT(0x00),
+	SMART_DAT(0xEF),
+	SMART_CMD(0x00),	/* Start of Window RAM address set(V) 16*/
+	SMART_CMD(0x52),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00),	/* End of Window RAM address set(V) 20*/
+	SMART_CMD(0x53),
+	SMART_DAT(0x01),
+	SMART_DAT(0x3F),
+	SMART_CMD(0x00), 	/* Panel interface control 1 */
+	SMART_CMD(0x90),
+	SMART_DAT(0x00),
+	SMART_DAT(0x1A),
+	SMART_CMD(0x00), 	/* Panel interface control 2 */
+	SMART_CMD(0x92),
+	SMART_DAT(0x04),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00), 	/* Panel interface control 3 */
+	SMART_CMD(0x93),
+	SMART_DAT(0x00),
+	SMART_DAT(0x05),
+	SMART_DELAY(20),
+};
+
+static uint16_t lcd_panel_on[] = {
+	SMART_CMD(0x00),
+	SMART_CMD(0x07),
+	SMART_DAT(0x00),
+	SMART_DAT(0x21),
+	SMART_DELAY(1),
+
+	SMART_CMD(0x00),
+	SMART_CMD(0x07),
+	SMART_DAT(0x00),
+	SMART_DAT(0x61),
+	SMART_DELAY(100),
+
+	SMART_CMD(0x00),
+	SMART_CMD(0x07),
+	SMART_DAT(0x01),
+	SMART_DAT(0x73),
+	SMART_DELAY(1),
+};
+
+static uint16_t lcd_panel_off[] = {
+	SMART_CMD(0x00),
+	SMART_CMD(0x07),
+	SMART_DAT(0x00),
+	SMART_DAT(0x72),
+	SMART_DELAY(40),
+
+	SMART_CMD(0x00),
+	SMART_CMD(0x07),
+	SMART_DAT(0x00),
+	SMART_DAT(0x01),
+	SMART_DELAY(1),
+
+	SMART_CMD(0x00),
+	SMART_CMD(0x07),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_DELAY(1),
+};
+
+static uint16_t lcd_power_off[] = {
+	SMART_CMD(0x00),
+	SMART_CMD(0x10),
+	SMART_DAT(0x00),
+	SMART_DAT(0x80),
+
+	SMART_CMD(0x00),
+	SMART_CMD(0x11),
+	SMART_DAT(0x01),
+	SMART_DAT(0x60),
+
+	SMART_CMD(0x00),
+	SMART_CMD(0x12),
+	SMART_DAT(0x01),
+	SMART_DAT(0xAE),
+	SMART_DELAY(40),
+
+	SMART_CMD(0x00),
+	SMART_CMD(0x10),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+};
+
+static uint16_t update_framedata[] = {
+	/* set display ram: 240*320 */
+	SMART_CMD(0x00), /* RAM address set(H) 0*/
+	SMART_CMD(0x20),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00), /* RAM address set(V) 4*/
+	SMART_CMD(0x21),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00), /* Start of Window RAM address set(H) 8 */
+	SMART_CMD(0x50),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00), /* End of Window RAM address set(H) 12 */
+	SMART_CMD(0x51),
+	SMART_DAT(0x00),
+	SMART_DAT(0xEF),
+	SMART_CMD(0x00), /* Start of Window RAM address set(V) 16 */
+	SMART_CMD(0x52),
+	SMART_DAT(0x00),
+	SMART_DAT(0x00),
+	SMART_CMD(0x00), /* End of Window RAM address set(V) 20 */
+	SMART_CMD(0x53),
+	SMART_DAT(0x01),
+	SMART_DAT(0x3F),
+
+	/* wait for vsync cmd before transferring frame data */
+	SMART_CMD_WAIT_FOR_VSYNC,
+
+	/* write ram */
+	SMART_CMD(0x00),
+	SMART_CMD(0x22),
+
+	/* write frame data */
+	SMART_CMD_WRITE_FRAME,
+};
+
+static void ltm022a97a_lcd_power(int on, struct fb_var_screeninfo *var)
+{
+	static int pin_requested = 0;
+	struct fb_info *info = container_of(var, struct fb_info, var);
+	int err;
+
+	if (!pin_requested) {
+		err = gpio_request(GPIO_LCD_RESET, "lcd reset");
+		if (err) {
+			pr_err("failed to request gpio for LCD reset\n");
+			return;
+		}
+
+		gpio_direction_output(GPIO_LCD_RESET, 0);
+		pin_requested = 1;
+	}
+
+	if (on) {
+		gpio_set_value(GPIO_LCD_RESET, 0); msleep(100);
+		gpio_set_value(GPIO_LCD_RESET, 1); msleep(10);
+
+		pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_power_on));
+		pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_panel_on));
+	} else {
+		pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_panel_off));
+		pxafb_smart_queue(info, ARRAY_AND_SIZE(lcd_power_off));
+	}
+
+	err = pxafb_smart_flush(info);
+	if (err)
+		pr_err("%s: timed out\n", __func__);
+}
+
+static void ltm022a97a_update(struct fb_info *info)
+{
+	pxafb_smart_queue(info, ARRAY_AND_SIZE(update_framedata));
+	pxafb_smart_flush(info);
+}
+
+static struct pxafb_mode_info toshiba_ltm022a97a_modes[] = {
+	[0] = {
+		.xres			= 240,
+		.yres			= 320,
+		.bpp			= 16,
+		.a0csrd_set_hld		= 30,
+		.a0cswr_set_hld		= 30,
+		.wr_pulse_width		= 30,
+		.rd_pulse_width 	= 30,
+		.op_hold_time 		= 30,
+		.cmd_inh_time		= 60,
+
+		/* L_LCLK_A0 and L_LCLK_RD active low */
+		.sync			= FB_SYNC_HOR_HIGH_ACT |
+					  FB_SYNC_VERT_HIGH_ACT,
+	},
+};
+
+static struct pxafb_mach_info saar_lcd_info = {
+	.modes			= toshiba_ltm022a97a_modes,
+	.num_modes		= 1,
+	.lcd_conn		= LCD_SMART_PANEL_8BPP | LCD_PCLK_EDGE_FALL,
+	.pxafb_lcd_power	= ltm022a97a_lcd_power,
+	.smart_update		= ltm022a97a_update,
+};
+
+static void __init saar_init_lcd(void)
+{
+	set_pxa_fb_info(&saar_lcd_info);
+}
+#else
+static inline void saar_init_lcd(void) {}
+#endif
+
+#if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
+static struct da903x_subdev_info saar_da9034_subdevs[] = {
+	[0] = {
+		.name		= "da903x-backlight",
+		.id		= DA9034_ID_WLED,
+	},
+};
+
+static struct da903x_platform_data saar_da9034_info = {
+	.num_subdevs	= ARRAY_SIZE(saar_da9034_subdevs),
+	.subdevs	= saar_da9034_subdevs,
+};
+
+static struct i2c_board_info saar_i2c_info[] = {
+	[0] = {
+		.type		= "da9034",
+		.addr		= 0x34,
+		.platform_data	= &saar_da9034_info,
+		.irq		= gpio_to_irq(mfp_to_gpio(MFP_PIN_GPIO83)),
+	},
+};
+
+static void __init saar_init_i2c(void)
+{
+	pxa_set_i2c_info(NULL);
+	i2c_register_board_info(0, ARRAY_AND_SIZE(saar_i2c_info));
+}
+#else
+static inline void saar_init_i2c(void) {}
+#endif
 static void __init saar_init(void)
 {
 	/* initialize MFP configurations */
 	pxa3xx_mfp_config(ARRAY_AND_SIZE(saar_mfp_cfg));
 
 	platform_device_register(&smc91x_device);
+
+	saar_init_i2c();
+	saar_init_lcd();
 }
 
 MACHINE_START(SAAR, "PXA930 Handheld Platform (aka SAAR)")