lguest: use a special 1:1 linear pagetable mode until first switch.

The Host used to create some page tables for the Guest to use at the
top of Guest memory; it would then tell the Guest where this was.  In
particular, it created linear mappings for 0 and 0xC0000000 addresses
because lguest used to switch to its real page tables quite late in
boot.

However, since d50d8fe19 Linux initialized boot page tables in
head_32.S even before the "are we lguest?" boot jump.  So, now we can
simplify things: the Host pagetable code assumes 1:1 linear mapping
until it first calls the LHCALL_NEW_PGTABLE hypercall, which we now do
before we reach C code.

This also means that the Host doesn't need to know anything about the
Guest's PAGE_OFFSET.  (Non-Linux guests might not even have such a
thing).

Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

3 files changed, 12 insertions, 9 deletions

diff --git a/arch/x86/kernel/asm-offsets_32.c b/arch/x86/kernel/asm-offsets_32.c
index c29d631..395a10e 100644
--- a/arch/x86/kernel/asm-offsets_32.c
+++ b/arch/x86/kernel/asm-offsets_32.c
@@ -63,7 +63,6 @@ void foo(void)
 	BLANK();
 	OFFSET(LGUEST_DATA_irq_enabled, lguest_data, irq_enabled);
 	OFFSET(LGUEST_DATA_irq_pending, lguest_data, irq_pending);
-	OFFSET(LGUEST_DATA_pgdir, lguest_data, pgdir);
 
 	BLANK();
 	OFFSET(LGUEST_PAGES_host_gdt_desc, lguest_pages, state.host_gdt_desc);
diff --git a/arch/x86/lguest/boot.c b/arch/x86/lguest/boot.c
index db832fd..719a32c 100644
--- a/arch/x86/lguest/boot.c
+++ b/arch/x86/lguest/boot.c
@@ -520,17 +520,16 @@ static unsigned long lguest_read_cr2(void)
 
 /* See lguest_set_pte() below. */
 static bool cr3_changed = false;
+static unsigned long current_cr3;
 
 /*
  * cr3 is the current toplevel pagetable page: the principle is the same as
- * cr0.  Keep a local copy, and tell the Host when it changes.  The only
- * difference is that our local copy is in lguest_data because the Host needs
- * to set it upon our initial hypercall.
+ * cr0.  Keep a local copy, and tell the Host when it changes.
  */
 static void lguest_write_cr3(unsigned long cr3)
 {
-	lguest_data.pgdir = cr3;
 	lazy_hcall1(LHCALL_NEW_PGTABLE, cr3);
+	current_cr3 = cr3;
 
 	/* These two page tables are simple, linear, and used during boot */
 	if (cr3 != __pa(swapper_pg_dir) && cr3 != __pa(initial_page_table))
@@ -539,7 +538,7 @@ static void lguest_write_cr3(unsigned long cr3)
 
 static unsigned long lguest_read_cr3(void)
 {
-	return lguest_data.pgdir;
+	return current_cr3;
 }
 
 /* cr4 is used to enable and disable PGE, but we don't care. */
@@ -758,7 +757,7 @@ static void lguest_pmd_clear(pmd_t *pmdp)
 static void lguest_flush_tlb_single(unsigned long addr)
 {
 	/* Simply set it to zero: if it was not, it will fault back in. */
-	lazy_hcall3(LHCALL_SET_PTE, lguest_data.pgdir, addr, 0);
+	lazy_hcall3(LHCALL_SET_PTE, current_cr3, addr, 0);
 }
 
 /*
diff --git a/arch/x86/lguest/i386_head.S b/arch/x86/lguest/i386_head.S
index 4f420c2f..863b03a 100644
--- a/arch/x86/lguest/i386_head.S
+++ b/arch/x86/lguest/i386_head.S
@@ -27,13 +27,18 @@
 .section .init.text, "ax", @progbits
 ENTRY(lguest_entry)
 	/*
-	 * We make the "initialization" hypercall now to tell the Host about
-	 * us, and also find out where it put our page tables.
+	 * We make the "initialization" hypercall now to tell the Host where
+	 * our lguest_data struct is.
 	 */
 	movl $LHCALL_LGUEST_INIT, %eax
 	movl $lguest_data - __PAGE_OFFSET, %ebx
 	int $LGUEST_TRAP_ENTRY
 
+	/* Now turn our pagetables on; setup by arch/x86/kernel/head_32.S. */
+	movl $LHCALL_NEW_PGTABLE, %eax
+	movl $(initial_page_table - __PAGE_OFFSET), %ebx
+	int $LGUEST_TRAP_ENTRY
+
 	/* Set up the initial stack so we can run C code. */
 	movl $(init_thread_union+THREAD_SIZE),%esp