Merge branch 'master' of /home/davem/src/GIT/linux-2.6/

Conflicts:
	drivers/firmware/iscsi_ibft.c

49 files changed, 2428 insertions, 1282 deletions

diff --git a/arch/mips/alchemy/Kconfig b/arch/mips/alchemy/Kconfig
index 00b498e..df3b1a7 100644
--- a/arch/mips/alchemy/Kconfig
+++ b/arch/mips/alchemy/Kconfig
@@ -1,5 +1,5 @@
-# au1000-style gpio
-config ALCHEMY_GPIO_AU1000
+# au1000-style gpio and interrupt controllers
+config ALCHEMY_GPIOINT_AU1000
 	bool
 
 # select this in your board config if you don't want to use the gpio
@@ -20,12 +20,14 @@ config MIPS_MTX1
 	select HW_HAS_PCI
 	select SOC_AU1500
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_BOSPORUS
 	bool "Alchemy Bosporus board"
 	select SOC_AU1500
 	select DMA_NONCOHERENT
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_DB1000
 	bool "Alchemy DB1000 board"
@@ -33,12 +35,14 @@ config MIPS_DB1000
 	select DMA_NONCOHERENT
 	select HW_HAS_PCI
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_DB1100
 	bool "Alchemy DB1100 board"
 	select SOC_AU1100
 	select DMA_NONCOHERENT
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_DB1200
 	bool "Alchemy DB1200 board"
@@ -46,6 +50,7 @@ config MIPS_DB1200
 	select DMA_COHERENT
 	select MIPS_DISABLE_OBSOLETE_IDE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_DB1500
 	bool "Alchemy DB1500 board"
@@ -55,6 +60,7 @@ config MIPS_DB1500
 	select MIPS_DISABLE_OBSOLETE_IDE
 	select SYS_SUPPORTS_BIG_ENDIAN
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_DB1550
 	bool "Alchemy DB1550 board"
@@ -63,12 +69,14 @@ config MIPS_DB1550
 	select DMA_NONCOHERENT
 	select MIPS_DISABLE_OBSOLETE_IDE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_MIRAGE
 	bool "Alchemy Mirage board"
 	select DMA_NONCOHERENT
 	select SOC_AU1500
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_PB1000
 	bool "Alchemy PB1000 board"
@@ -77,6 +85,7 @@ config MIPS_PB1000
 	select HW_HAS_PCI
 	select SWAP_IO_SPACE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_PB1100
 	bool "Alchemy PB1100 board"
@@ -85,6 +94,7 @@ config MIPS_PB1100
 	select HW_HAS_PCI
 	select SWAP_IO_SPACE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_PB1200
 	bool "Alchemy PB1200 board"
@@ -92,6 +102,7 @@ config MIPS_PB1200
 	select DMA_NONCOHERENT
 	select MIPS_DISABLE_OBSOLETE_IDE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_PB1500
 	bool "Alchemy PB1500 board"
@@ -99,6 +110,7 @@ config MIPS_PB1500
 	select DMA_NONCOHERENT
 	select HW_HAS_PCI
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_PB1550
 	bool "Alchemy PB1550 board"
@@ -107,39 +119,41 @@ config MIPS_PB1550
 	select HW_HAS_PCI
 	select MIPS_DISABLE_OBSOLETE_IDE
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 config MIPS_XXS1500
 	bool "MyCable XXS1500 board"
 	select DMA_NONCOHERENT
 	select SOC_AU1500
 	select SYS_SUPPORTS_LITTLE_ENDIAN
+	select SYS_HAS_EARLY_PRINTK
 
 endchoice
 
 config SOC_AU1000
 	bool
 	select SOC_AU1X00
-	select ALCHEMY_GPIO_AU1000
+	select ALCHEMY_GPIOINT_AU1000
 
 config SOC_AU1100
 	bool
 	select SOC_AU1X00
-	select ALCHEMY_GPIO_AU1000
+	select ALCHEMY_GPIOINT_AU1000
 
 config SOC_AU1500
 	bool
 	select SOC_AU1X00
-	select ALCHEMY_GPIO_AU1000
+	select ALCHEMY_GPIOINT_AU1000
 
 config SOC_AU1550
 	bool
 	select SOC_AU1X00
-	select ALCHEMY_GPIO_AU1000
+	select ALCHEMY_GPIOINT_AU1000
 
 config SOC_AU1200
 	bool
 	select SOC_AU1X00
-	select ALCHEMY_GPIO_AU1000
+	select ALCHEMY_GPIOINT_AU1000
 
 config SOC_AU1X00
 	bool
diff --git a/arch/mips/alchemy/common/Makefile b/arch/mips/alchemy/common/Makefile
index b67fb51..06c0e65 100644
--- a/arch/mips/alchemy/common/Makefile
+++ b/arch/mips/alchemy/common/Makefile
@@ -5,14 +5,15 @@
 # Makefile for the Alchemy Au1xx0 CPUs, generic files.
 #
 
-obj-y += prom.o irq.o puts.o time.o reset.o \
-	clocks.o platform.o power.o setup.o \
+obj-y += prom.o time.o clocks.o platform.o power.o setup.o \
 	sleeper.o dma.o dbdma.o
 
+obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += irq.o
+
 # optional gpiolib support
 ifeq ($(CONFIG_ALCHEMY_GPIO_INDIRECT),)
  ifeq ($(CONFIG_GPIOLIB),y)
-  obj-$(CONFIG_ALCHEMY_GPIO_AU1000) += gpiolib-au1000.o
+  obj-$(CONFIG_ALCHEMY_GPIOINT_AU1000) += gpiolib-au1000.o
  endif
 endif
 
diff --git a/arch/mips/alchemy/common/clocks.c b/arch/mips/alchemy/common/clocks.c
index d899185..460c628 100644
--- a/arch/mips/alchemy/common/clocks.c
+++ b/arch/mips/alchemy/common/clocks.c
@@ -40,8 +40,6 @@
 static unsigned int au1x00_clock; /*  Hz */
 static unsigned long uart_baud_base;
 
-static DEFINE_SPINLOCK(time_lock);
-
 /*
  * Set the au1000_clock
  */
@@ -84,9 +82,6 @@ void set_au1x00_uart_baud_base(unsigned long new_baud_base)
 unsigned long au1xxx_calc_clock(void)
 {
 	unsigned long cpu_speed;
-	unsigned long flags;
-
-	spin_lock_irqsave(&time_lock, flags);
 
 	/*
 	 * On early Au1000, sys_cpupll was write-only. Since these
@@ -108,8 +103,6 @@ unsigned long au1xxx_calc_clock(void)
 	set_au1x00_uart_baud_base(cpu_speed / (2 * ((int)(au_readl(SYS_POWERCTRL)
 							  & 0x03) + 2) * 16));
 
-	spin_unlock_irqrestore(&time_lock, flags);
-
 	set_au1x00_speed(cpu_speed);
 
 	return cpu_speed;
diff --git a/arch/mips/alchemy/common/dbdma.c b/arch/mips/alchemy/common/dbdma.c
index f9201ca..99ae84c 100644
--- a/arch/mips/alchemy/common/dbdma.c
+++ b/arch/mips/alchemy/common/dbdma.c
@@ -30,6 +30,7 @@
  *
  */
 
+#include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
@@ -58,7 +59,6 @@ static DEFINE_SPINLOCK(au1xxx_dbdma_spin_lock);
 
 static dbdma_global_t *dbdma_gptr = (dbdma_global_t *)DDMA_GLOBAL_BASE;
 static int dbdma_initialized;
-static void au1xxx_dbdma_init(void);
 
 static dbdev_tab_t dbdev_tab[] = {
 #ifdef CONFIG_SOC_AU1550
@@ -237,7 +237,7 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
        void (*callback)(int, void *), void *callparam)
 {
 	unsigned long   flags;
-	u32		used, chan, rv;
+	u32		used, chan;
 	u32		dcp;
 	int		i;
 	dbdev_tab_t	*stp, *dtp;
@@ -250,8 +250,7 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
 	 * which can't be done successfully during board set up.
 	 */
 	if (!dbdma_initialized)
-		au1xxx_dbdma_init();
-	dbdma_initialized = 1;
+		return 0;
 
 	stp = find_dbdev_id(srcid);
 	if (stp == NULL)
@@ -261,7 +260,6 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
 		return 0;
 
 	used = 0;
-	rv = 0;
 
 	/* Check to see if we can get both channels. */
 	spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
@@ -282,63 +280,65 @@ u32 au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid,
 		used++;
 	spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
 
-	if (!used) {
-		/* Let's see if we can allocate a channel for it. */
-		ctp = NULL;
-		chan = 0;
-		spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
-		for (i = 0; i < NUM_DBDMA_CHANS; i++)
-			if (chan_tab_ptr[i] == NULL) {
-				/*
-				 * If kmalloc fails, it is caught below same
-				 * as a channel not available.
-				 */
-				ctp = kmalloc(sizeof(chan_tab_t), GFP_ATOMIC);
-				chan_tab_ptr[i] = ctp;
-				break;
-			}
-		spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
-
-		if (ctp != NULL) {
-			memset(ctp, 0, sizeof(chan_tab_t));
-			ctp->chan_index = chan = i;
-			dcp = DDMA_CHANNEL_BASE;
-			dcp += (0x0100 * chan);
-			ctp->chan_ptr = (au1x_dma_chan_t *)dcp;
-			cp = (au1x_dma_chan_t *)dcp;
-			ctp->chan_src = stp;
-			ctp->chan_dest = dtp;
-			ctp->chan_callback = callback;
-			ctp->chan_callparam = callparam;
-
-			/* Initialize channel configuration. */
-			i = 0;
-			if (stp->dev_intlevel)
-				i |= DDMA_CFG_SED;
-			if (stp->dev_intpolarity)
-				i |= DDMA_CFG_SP;
-			if (dtp->dev_intlevel)
-				i |= DDMA_CFG_DED;
-			if (dtp->dev_intpolarity)
-				i |= DDMA_CFG_DP;
-			if ((stp->dev_flags & DEV_FLAGS_SYNC) ||
-				(dtp->dev_flags & DEV_FLAGS_SYNC))
-					i |= DDMA_CFG_SYNC;
-			cp->ddma_cfg = i;
-			au_sync();
+	if (used)
+		return 0;
 
-			/* Return a non-zero value that can be used to
-			 * find the channel information in subsequent
-			 * operations.
+	/* Let's see if we can allocate a channel for it. */
+	ctp = NULL;
+	chan = 0;
+	spin_lock_irqsave(&au1xxx_dbdma_spin_lock, flags);
+	for (i = 0; i < NUM_DBDMA_CHANS; i++)
+		if (chan_tab_ptr[i] == NULL) {
+			/*
+			 * If kmalloc fails, it is caught below same
+			 * as a channel not available.
 			 */
-			rv = (u32)(&chan_tab_ptr[chan]);
-		} else {
-			/* Release devices */
-			stp->dev_flags &= ~DEV_FLAGS_INUSE;
-			dtp->dev_flags &= ~DEV_FLAGS_INUSE;
+			ctp = kmalloc(sizeof(chan_tab_t), GFP_ATOMIC);
+			chan_tab_ptr[i] = ctp;
+			break;
 		}
+	spin_unlock_irqrestore(&au1xxx_dbdma_spin_lock, flags);
+
+	if (ctp != NULL) {
+		memset(ctp, 0, sizeof(chan_tab_t));
+		ctp->chan_index = chan = i;
+		dcp = DDMA_CHANNEL_BASE;
+		dcp += (0x0100 * chan);
+		ctp->chan_ptr = (au1x_dma_chan_t *)dcp;
+		cp = (au1x_dma_chan_t *)dcp;
+		ctp->chan_src = stp;
+		ctp->chan_dest = dtp;
+		ctp->chan_callback = callback;
+		ctp->chan_callparam = callparam;
+
+		/* Initialize channel configuration. */
+		i = 0;
+		if (stp->dev_intlevel)
+			i |= DDMA_CFG_SED;
+		if (stp->dev_intpolarity)
+			i |= DDMA_CFG_SP;
+		if (dtp->dev_intlevel)
+			i |= DDMA_CFG_DED;
+		if (dtp->dev_intpolarity)
+			i |= DDMA_CFG_DP;
+		if ((stp->dev_flags & DEV_FLAGS_SYNC) ||
+			(dtp->dev_flags & DEV_FLAGS_SYNC))
+				i |= DDMA_CFG_SYNC;
+		cp->ddma_cfg = i;
+		au_sync();
+
+		/*
+		 * Return a non-zero value that can be used to find the channel
+		 * information in subsequent operations.
+		 */
+		return (u32)(&chan_tab_ptr[chan]);
 	}
-	return rv;
+
+	/* Release devices */
+	stp->dev_flags &= ~DEV_FLAGS_INUSE;
+	dtp->dev_flags &= ~DEV_FLAGS_INUSE;
+
+	return 0;
 }
 EXPORT_SYMBOL(au1xxx_dbdma_chan_alloc);
 
@@ -572,7 +572,7 @@ EXPORT_SYMBOL(au1xxx_dbdma_ring_alloc);
  * This updates the source pointer and byte count.  Normally used
  * for memory to fifo transfers.
  */
-u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags)
+u32 au1xxx_dbdma_put_source(u32 chanid, dma_addr_t buf, int nbytes, u32 flags)
 {
 	chan_tab_t		*ctp;
 	au1x_ddma_desc_t	*dp;
@@ -598,7 +598,7 @@ u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags)
 		return 0;
 
 	/* Load up buffer address and byte count. */
-	dp->dscr_source0 = virt_to_phys(buf);
+	dp->dscr_source0 = buf & ~0UL;
 	dp->dscr_cmd1 = nbytes;
 	/* Check flags */
 	if (flags & DDMA_FLAGS_IE)
@@ -625,14 +625,13 @@ u32 _au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags)
 	/* Return something non-zero. */
 	return nbytes;
 }
-EXPORT_SYMBOL(_au1xxx_dbdma_put_source);
+EXPORT_SYMBOL(au1xxx_dbdma_put_source);
 
 /* Put a destination buffer into the DMA ring.
  * This updates the destination pointer and byte count.  Normally used
  * to place an empty buffer into the ring for fifo to memory transfers.
  */
-u32
-_au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags)
+u32 au1xxx_dbdma_put_dest(u32 chanid, dma_addr_t buf, int nbytes, u32 flags)
 {
 	chan_tab_t		*ctp;
 	au1x_ddma_desc_t	*dp;
@@ -662,7 +661,7 @@ _au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags)
 	if (flags & DDMA_FLAGS_NOIE)
 		dp->dscr_cmd0 &= ~DSCR_CMD0_IE;
 
-	dp->dscr_dest0 = virt_to_phys(buf);
+	dp->dscr_dest0 = buf & ~0UL;
 	dp->dscr_cmd1 = nbytes;
 #if 0
 	printk(KERN_DEBUG "cmd0:%x cmd1:%x source0:%x source1:%x dest0:%x dest1:%x\n",
@@ -688,7 +687,7 @@ _au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags)
 	/* Return something non-zero. */
 	return nbytes;
 }
-EXPORT_SYMBOL(_au1xxx_dbdma_put_dest);
+EXPORT_SYMBOL(au1xxx_dbdma_put_dest);
 
 /*
  * Get a destination buffer into the DMA ring.
@@ -871,28 +870,6 @@ static irqreturn_t dbdma_interrupt(int irq, void *dev_id)
 	return IRQ_RETVAL(1);
 }
 
-static void au1xxx_dbdma_init(void)
-{
-	int irq_nr;
-
-	dbdma_gptr->ddma_config = 0;
-	dbdma_gptr->ddma_throttle = 0;
-	dbdma_gptr->ddma_inten = 0xffff;
-	au_sync();
-
-#if defined(CONFIG_SOC_AU1550)
-	irq_nr = AU1550_DDMA_INT;
-#elif defined(CONFIG_SOC_AU1200)
-	irq_nr = AU1200_DDMA_INT;
-#else
-	#error Unknown Au1x00 SOC
-#endif
-
-	if (request_irq(irq_nr, dbdma_interrupt, IRQF_DISABLED,
-			"Au1xxx dbdma", (void *)dbdma_gptr))
-		printk(KERN_ERR "Can't get 1550 dbdma irq");
-}
-
 void au1xxx_dbdma_dump(u32 chanid)
 {
 	chan_tab_t	 *ctp;
@@ -906,7 +883,7 @@ void au1xxx_dbdma_dump(u32 chanid)
 	dtp = ctp->chan_dest;
 	cp = ctp->chan_ptr;
 
-	printk(KERN_DEBUG "Chan %x, stp %x (dev %d)  dtp %x (dev %d) \n",
+	printk(KERN_DEBUG "Chan %x, stp %x (dev %d)  dtp %x (dev %d)\n",
 			  (u32)ctp, (u32)stp, stp - dbdev_tab, (u32)dtp,
 			  dtp - dbdev_tab);
 	printk(KERN_DEBUG "desc base %x, get %x, put %x, cur %x\n",
@@ -1041,4 +1018,38 @@ void au1xxx_dbdma_resume(void)
 	}
 }
 #endif	/* CONFIG_PM */
+
+static int __init au1xxx_dbdma_init(void)
+{
+	int irq_nr, ret;
+
+	dbdma_gptr->ddma_config = 0;
+	dbdma_gptr->ddma_throttle = 0;
+	dbdma_gptr->ddma_inten = 0xffff;
+	au_sync();
+
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1550:
+		irq_nr = AU1550_DDMA_INT;
+		break;
+	case ALCHEMY_CPU_AU1200:
+		irq_nr = AU1200_DDMA_INT;
+		break;
+	default:
+		return -ENODEV;
+	}
+
+	ret = request_irq(irq_nr, dbdma_interrupt, IRQF_DISABLED,
+			"Au1xxx dbdma", (void *)dbdma_gptr);
+	if (ret)
+		printk(KERN_ERR "Cannot grab DBDMA interrupt!\n");
+	else {
+		dbdma_initialized = 1;
+		printk(KERN_INFO "Alchemy DBDMA initialized\n");
+	}
+
+	return ret;
+}
+subsys_initcall(au1xxx_dbdma_init);
+
 #endif /* defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200) */
diff --git a/arch/mips/alchemy/common/dma.c b/arch/mips/alchemy/common/dma.c
index d6fbda2..d527887 100644
--- a/arch/mips/alchemy/common/dma.c
+++ b/arch/mips/alchemy/common/dma.c
@@ -29,6 +29,8 @@
  *  675 Mass Ave, Cambridge, MA 02139, USA.
  *
  */
+
+#include <linux/init.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/errno.h>
@@ -188,17 +190,14 @@ int request_au1000_dma(int dev_id, const char *dev_str,
 		dev = &dma_dev_table[dev_id];
 
 	if (irqhandler) {
-		chan->irq = AU1000_DMA_INT_BASE + i;
 		chan->irq_dev = irq_dev_id;
 		ret = request_irq(chan->irq, irqhandler, irqflags, dev_str,
 				  chan->irq_dev);
 		if (ret) {
-			chan->irq = 0;
 			chan->irq_dev = NULL;
 			return ret;
 		}
 	} else {
-		chan->irq = 0;
 		chan->irq_dev = NULL;
 	}
 
@@ -226,13 +225,40 @@ void free_au1000_dma(unsigned int dmanr)
 	}
 
 	disable_dma(dmanr);
-	if (chan->irq)
+	if (chan->irq_dev)
 		free_irq(chan->irq, chan->irq_dev);
 
-	chan->irq = 0;
 	chan->irq_dev = NULL;
 	chan->dev_id = -1;
 }
 EXPORT_SYMBOL(free_au1000_dma);
 
+static int __init au1000_dma_init(void)
+{
+        int base, i;
+
+        switch (alchemy_get_cputype()) {
+        case ALCHEMY_CPU_AU1000:
+                base = AU1000_DMA_INT_BASE;
+                break;
+        case ALCHEMY_CPU_AU1500:
+                base = AU1500_DMA_INT_BASE;
+                break;
+        case ALCHEMY_CPU_AU1100:
+                base = AU1100_DMA_INT_BASE;
+                break;
+        default:
+                goto out;
+        }
+
+        for (i = 0; i < NUM_AU1000_DMA_CHANNELS; i++)
+                au1000_dma_table[i].irq = base + i;
+
+        printk(KERN_INFO "Alchemy DMA initialized\n");
+
+out:
+        return 0;
+}
+arch_initcall(au1000_dma_init);
+
 #endif /* AU1000 AU1500 AU1100 */
diff --git a/arch/mips/alchemy/common/gpiolib-au1000.c b/arch/mips/alchemy/common/gpiolib-au1000.c
index 1bfa91f..c8e1a94 100644
--- a/arch/mips/alchemy/common/gpiolib-au1000.c
+++ b/arch/mips/alchemy/common/gpiolib-au1000.c
@@ -36,7 +36,6 @@
 #include <asm/mach-au1x00/au1000.h>
 #include <asm/mach-au1x00/gpio.h>
 
-#if !defined(CONFIG_SOC_AU1000)
 static int gpio2_get(struct gpio_chip *chip, unsigned offset)
 {
 	return alchemy_gpio2_get_value(offset + ALCHEMY_GPIO2_BASE);
@@ -63,7 +62,7 @@ static int gpio2_to_irq(struct gpio_chip *chip, unsigned offset)
 {
 	return alchemy_gpio2_to_irq(offset + ALCHEMY_GPIO2_BASE);
 }
-#endif /* !defined(CONFIG_SOC_AU1000) */
+
 
 static int gpio1_get(struct gpio_chip *chip, unsigned offset)
 {
@@ -104,7 +103,6 @@ struct gpio_chip alchemy_gpio_chip[] = {
 		.base			= ALCHEMY_GPIO1_BASE,
 		.ngpio			= ALCHEMY_GPIO1_NUM,
 	},
-#if !defined(CONFIG_SOC_AU1000)
 	[1] = {
 		.label                  = "alchemy-gpio2",
 		.direction_input        = gpio2_direction_input,
@@ -115,15 +113,13 @@ struct gpio_chip alchemy_gpio_chip[] = {
 		.base                   = ALCHEMY_GPIO2_BASE,
 		.ngpio                  = ALCHEMY_GPIO2_NUM,
 	},
-#endif
 };
 
 static int __init alchemy_gpiolib_init(void)
 {
 	gpiochip_add(&alchemy_gpio_chip[0]);
-#if !defined(CONFIG_SOC_AU1000)
-	gpiochip_add(&alchemy_gpio_chip[1]);
-#endif
+	if (alchemy_get_cputype() != ALCHEMY_CPU_AU1000)
+		gpiochip_add(&alchemy_gpio_chip[1]);
 
 	return 0;
 }
diff --git a/arch/mips/alchemy/common/irq.c b/arch/mips/alchemy/common/irq.c
index d670928..b2821ac 100644
--- a/arch/mips/alchemy/common/irq.c
+++ b/arch/mips/alchemy/common/irq.c
@@ -39,168 +39,180 @@
 
 static int au1x_ic_settype(unsigned int irq, unsigned int flow_type);
 
+/* NOTE on interrupt priorities: The original writers of this code said:
+ *
+ * Because of the tight timing of SETUP token to reply transactions,
+ * the USB devices-side packet complete interrupt (USB_DEV_REQ_INT)
+ * needs the highest priority.
+ */
+
 /* per-processor fixed function irqs */
-struct au1xxx_irqmap au1xxx_ic0_map[] __initdata = {
-
-#if defined(CONFIG_SOC_AU1000)
-	{ AU1000_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_UART2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
-	{ AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
-
-#elif defined(CONFIG_SOC_AU1500)
-
-	{ AU1500_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1000_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1500_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1000_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
-	{ AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1500_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1500_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
-
-#elif defined(CONFIG_SOC_AU1100)
-
-	{ AU1100_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1100_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1100_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1100_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_SSI0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_SSI1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+1, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+2, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+3, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+4, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+5, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+6, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_DMA_INT_BASE+7, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
-	{ AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_IRDA_TX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_IRDA_RX_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+struct au1xxx_irqmap {
+	int im_irq;
+	int im_type;
+	int im_request;		/* set 1 to get higher priority */
+};
+
+struct au1xxx_irqmap au1000_irqmap[] __initdata = {
+	{ AU1000_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_UART2_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_SSI0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_SSI1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE+1,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE+2,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE+3,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE+4,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE+5,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE+6,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_DMA_INT_BASE+7,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1 },
+	{ AU1000_IRDA_TX_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_IRDA_RX_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,  1 },
 	{ AU1000_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1000_ACSYNC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1100_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1100_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_AC97C_INT, IRQ_TYPE_EDGE_RISING, 0 },
-
-#elif defined(CONFIG_SOC_AU1550)
-
-	{ AU1550_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_PCI_INTA, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1550_PCI_INTB, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1550_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_CRYPTO_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_PCI_INTC, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1550_PCI_INTD, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1550_PCI_RST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1550_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_UART3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_PSC2_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_PSC3_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
-	{ AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1550_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1550_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
+	{ AU1000_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1000_ACSYNC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1000_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_MAC1_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1000_AC97C_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ -1, },
+};
+
+struct au1xxx_irqmap au1500_irqmap[] __initdata = {
+	{ AU1500_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_PCI_INTA,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1500_PCI_INTB,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1500_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_PCI_INTC,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1500_PCI_INTD,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1500_DMA_INT_BASE,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_DMA_INT_BASE+1,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_DMA_INT_BASE+2,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_DMA_INT_BASE+3,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_DMA_INT_BASE+4,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_DMA_INT_BASE+5,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_DMA_INT_BASE+6,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_DMA_INT_BASE+7,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1 },
+	{ AU1500_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,  1 },
+	{ AU1500_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1500_ACSYNC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1500_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_MAC1_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1500_AC97C_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ -1, },
+};
+
+struct au1xxx_irqmap au1100_irqmap[] __initdata = {
+	{ AU1100_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_SD_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_SSI0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_SSI1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE+1,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE+2,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE+3,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE+4,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE+5,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE+6,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_DMA_INT_BASE+7,  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1 },
+	{ AU1100_IRDA_TX_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_IRDA_RX_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,  1 },
+	{ AU1100_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1100_ACSYNC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1100_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_LCD_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1100_AC97C_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ -1, },
+};
+
+struct au1xxx_irqmap au1550_irqmap[] __initdata = {
+	{ AU1550_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_PCI_INTA,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1550_PCI_INTB,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1550_DDMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_CRYPTO_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_PCI_INTC,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1550_PCI_INTD,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1550_PCI_RST_INT,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1550_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_UART3_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_PSC0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_PSC1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_PSC2_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_PSC3_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1 },
+	{ AU1550_NAND_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1550_USB_DEV_REQ_INT, IRQ_TYPE_LEVEL_HIGH,  1 },
 	{ AU1550_USB_DEV_SUS_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1550_USB_HOST_INT, IRQ_TYPE_LEVEL_LOW, 0 },
-	{ AU1550_MAC0_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1550_MAC1_DMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-
-#elif defined(CONFIG_SOC_AU1200)
-
-	{ AU1200_UART0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_SWT_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1200_SD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_DDMA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_MAE_BE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_UART1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_MAE_FE_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_PSC0_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_PSC1_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_AES_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_CAMERA_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1000_TOY_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_TOY_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 1 },
-	{ AU1000_RTC_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH0_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH1_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1000_RTC_MATCH2_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1200_NAND_INT, IRQ_TYPE_EDGE_RISING, 0 },
-	{ AU1200_USB_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_LCD_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-	{ AU1200_MAE_BOTH_INT, IRQ_TYPE_LEVEL_HIGH, 0 },
-
-#else
-#error "Error: Unknown Alchemy SOC"
-#endif
+	{ AU1550_USB_HOST_INT,	  IRQ_TYPE_LEVEL_LOW,   0 },
+	{ AU1550_MAC0_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1550_MAC1_DMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ -1, },
+};
+
+struct au1xxx_irqmap au1200_irqmap[] __initdata = {
+	{ AU1200_UART0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_SWT_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_SD_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_DDMA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_MAE_BE_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_UART1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_MAE_FE_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_PSC0_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_PSC1_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_AES_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_CAMERA_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_TOY_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_TOY_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_TOY_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_TOY_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_RTC_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_RTC_MATCH0_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_RTC_MATCH1_INT,  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_RTC_MATCH2_INT,  IRQ_TYPE_EDGE_RISING, 1 },
+	{ AU1200_NAND_INT,	  IRQ_TYPE_EDGE_RISING, 0 },
+	{ AU1200_USB_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_LCD_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ AU1200_MAE_BOTH_INT,	  IRQ_TYPE_LEVEL_HIGH,  0 },
+	{ -1, },
 };
 
 
@@ -306,7 +318,7 @@ static void au1x_ic1_unmask(unsigned int irq_nr)
  * nowhere in the current kernel sources is it disabled.	--mlau
  */
 #if defined(CONFIG_MIPS_PB1000)
-	if (irq_nr == AU1000_GPIO_15)
+	if (irq_nr == AU1000_GPIO15_INT)
 		au_writel(0x4000, PB1000_MDR); /* enable int */
 #endif
 	au_sync();
@@ -378,11 +390,13 @@ static void au1x_ic1_maskack(unsigned int irq_nr)
 
 static int au1x_ic1_setwake(unsigned int irq, unsigned int on)
 {
-	unsigned int bit = irq - AU1000_INTC1_INT_BASE;
+	int bit = irq - AU1000_INTC1_INT_BASE;
 	unsigned long wakemsk, flags;
 
-	/* only GPIO 0-7 can act as wakeup source: */
-	if ((irq < AU1000_GPIO_0) || (irq > AU1000_GPIO_7))
+	/* only GPIO 0-7 can act as wakeup source.  Fortunately these
+	 * are wired up identically on all supported variants.
+	 */
+	if ((bit < 0) || (bit > 7))
 		return -EINVAL;
 
 	local_irq_save(flags);
@@ -504,11 +518,11 @@ static int au1x_ic_settype(unsigned int irq, unsigned int flow_type)
 asmlinkage void plat_irq_dispatch(void)
 {
 	unsigned int pending = read_c0_status() & read_c0_cause();
-	unsigned long s, off, bit;
+	unsigned long s, off;
 
 	if (pending & CAUSEF_IP7) {
-		do_IRQ(MIPS_CPU_IRQ_BASE + 7);
-		return;
+		off = MIPS_CPU_IRQ_BASE + 7;
+		goto handle;
 	} else if (pending & CAUSEF_IP2) {
 		s = IC0_REQ0INT;
 		off = AU1000_INTC0_INT_BASE;
@@ -524,58 +538,20 @@ asmlinkage void plat_irq_dispatch(void)
 	} else
 		goto spurious;
 
-	bit = 0;
 	s = au_readl(s);
 	if (unlikely(!s)) {
 spurious:
 		spurious_interrupt();
 		return;
 	}
-#ifdef AU1000_USB_DEV_REQ_INT
-	/*
-	 * Because of the tight timing of SETUP token to reply
-	 * transactions, the USB devices-side packet complete
-	 * interrupt needs the highest priority.
-	 */
-	bit = 1 << (AU1000_USB_DEV_REQ_INT - AU1000_INTC0_INT_BASE);
-	if ((pending & CAUSEF_IP2) && (s & bit)) {
-		do_IRQ(AU1000_USB_DEV_REQ_INT);
-		return;
-	}
-#endif
-	do_IRQ(__ffs(s) + off);
+	off += __ffs(s);
+handle:
+	do_IRQ(off);
 }
 
-/* setup edge/level and assign request 0/1 */
-void __init au1xxx_setup_irqmap(struct au1xxx_irqmap *map, int count)
+static void __init au1000_init_irq(struct au1xxx_irqmap *map)
 {
 	unsigned int bit, irq_nr;
-
-	while (count--) {
-		irq_nr = map[count].im_irq;
-
-		if (((irq_nr < AU1000_INTC0_INT_BASE) ||
-		     (irq_nr >= AU1000_INTC0_INT_BASE + 32)) &&
-		    ((irq_nr < AU1000_INTC1_INT_BASE) ||
-		     (irq_nr >= AU1000_INTC1_INT_BASE + 32)))
-			continue;
-
-		if (irq_nr >= AU1000_INTC1_INT_BASE) {
-			bit = irq_nr - AU1000_INTC1_INT_BASE;
-			if (map[count].im_request)
-				au_writel(1 << bit, IC1_ASSIGNCLR);
-		} else {
-			bit = irq_nr - AU1000_INTC0_INT_BASE;
-			if (map[count].im_request)
-				au_writel(1 << bit, IC0_ASSIGNCLR);
-		}
-
-		au1x_ic_settype(irq_nr, map[count].im_type);
-	}
-}
-
-void __init arch_init_irq(void)
-{
 	int i;
 
 	/*
@@ -585,7 +561,7 @@ void __init arch_init_irq(void)
 	au_writel(0xffffffff, IC0_CFG1CLR);
 	au_writel(0xffffffff, IC0_CFG2CLR);
 	au_writel(0xffffffff, IC0_MASKCLR);
-	au_writel(0xffffffff, IC0_ASSIGNSET);
+	au_writel(0xffffffff, IC0_ASSIGNCLR);
 	au_writel(0xffffffff, IC0_WAKECLR);
 	au_writel(0xffffffff, IC0_SRCSET);
 	au_writel(0xffffffff, IC0_FALLINGCLR);
@@ -596,7 +572,7 @@ void __init arch_init_irq(void)
 	au_writel(0xffffffff, IC1_CFG1CLR);
 	au_writel(0xffffffff, IC1_CFG2CLR);
 	au_writel(0xffffffff, IC1_MASKCLR);
-	au_writel(0xffffffff, IC1_ASSIGNSET);
+	au_writel(0xffffffff, IC1_ASSIGNCLR);
 	au_writel(0xffffffff, IC1_WAKECLR);
 	au_writel(0xffffffff, IC1_SRCSET);
 	au_writel(0xffffffff, IC1_FALLINGCLR);
@@ -619,11 +595,43 @@ void __init arch_init_irq(void)
 	/*
 	 * Initialize IC0, which is fixed per processor.
 	 */
-	au1xxx_setup_irqmap(au1xxx_ic0_map, ARRAY_SIZE(au1xxx_ic0_map));
+	while (map->im_irq != -1) {
+		irq_nr = map->im_irq;
 
-	/* Boards can register additional (GPIO-based) IRQs.
-	*/
-	board_init_irq();
+		if (irq_nr >= AU1000_INTC1_INT_BASE) {
+			bit = irq_nr - AU1000_INTC1_INT_BASE;
+			if (map->im_request)
+				au_writel(1 << bit, IC1_ASSIGNSET);
+		} else {
+			bit = irq_nr - AU1000_INTC0_INT_BASE;
+			if (map->im_request)
+				au_writel(1 << bit, IC0_ASSIGNSET);
+		}
+
+		au1x_ic_settype(irq_nr, map->im_type);
+		++map;
+	}
 
 	set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3);
 }
+
+void __init arch_init_irq(void)
+{
+	switch (alchemy_get_cputype()) {
+	case ALCHEMY_CPU_AU1000:
+		au1000_init_irq(au1000_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1500:
+		au1000_init_irq(au1500_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1100:
+		au1000_init_irq(au1100_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1550:
+		au1000_init_irq(au1550_irqmap);
+		break;
+	case ALCHEMY_CPU_AU1200:
+		au1000_init_irq(au1200_irqmap);
+		break;
+	}
+}
diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 117f99f..2580e77 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -19,39 +19,40 @@
 #include <asm/mach-au1x00/au1xxx.h>
 #include <asm/mach-au1x00/au1xxx_dbdma.h>
 #include <asm/mach-au1x00/au1100_mmc.h>
-
-#define PORT(_base, _irq)				\
-	{						\
-		.iobase		= _base,		\
-		.membase	= (void __iomem *)_base,\
-		.mapbase	= CPHYSADDR(_base),	\
-		.irq		= _irq,			\
-		.regshift	= 2,			\
-		.iotype		= UPIO_AU,		\
-		.flags		= UPF_SKIP_TEST 	\
+#include <asm/mach-au1x00/au1xxx_eth.h>
+
+#define PORT(_base, _irq)					\
+	{							\
+		.mapbase	= _base,			\
+		.irq		= _irq,				\
+		.regshift	= 2,				\
+		.iotype		= UPIO_AU,			\
+		.flags		= UPF_SKIP_TEST | UPF_IOREMAP |	\
+				  UPF_FIXED_TYPE,		\
+		.type		= PORT_16550A,			\
 	}
 
 static struct plat_serial8250_port au1x00_uart_data[] = {
 #if defined(CONFIG_SERIAL_8250_AU1X00)
 #if defined(CONFIG_SOC_AU1000)
-	PORT(UART0_ADDR, AU1000_UART0_INT),
-	PORT(UART1_ADDR, AU1000_UART1_INT),
-	PORT(UART2_ADDR, AU1000_UART2_INT),
-	PORT(UART3_ADDR, AU1000_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
+	PORT(UART2_PHYS_ADDR, AU1000_UART2_INT),
+	PORT(UART3_PHYS_ADDR, AU1000_UART3_INT),
 #elif defined(CONFIG_SOC_AU1500)
-	PORT(UART0_ADDR, AU1500_UART0_INT),
-	PORT(UART3_ADDR, AU1500_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1500_UART0_INT),
+	PORT(UART3_PHYS_ADDR, AU1500_UART3_INT),
 #elif defined(CONFIG_SOC_AU1100)
-	PORT(UART0_ADDR, AU1100_UART0_INT),
-	PORT(UART1_ADDR, AU1100_UART1_INT),
-	PORT(UART3_ADDR, AU1100_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1100_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1100_UART1_INT),
+	PORT(UART3_PHYS_ADDR, AU1100_UART3_INT),
 #elif defined(CONFIG_SOC_AU1550)
-	PORT(UART0_ADDR, AU1550_UART0_INT),
-	PORT(UART1_ADDR, AU1550_UART1_INT),
-	PORT(UART3_ADDR, AU1550_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1550_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1550_UART1_INT),
+	PORT(UART3_PHYS_ADDR, AU1550_UART3_INT),
 #elif defined(CONFIG_SOC_AU1200)
-	PORT(UART0_ADDR, AU1200_UART0_INT),
-	PORT(UART1_ADDR, AU1200_UART1_INT),
+	PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
 #endif
 #endif	/* CONFIG_SERIAL_8250_AU1X00 */
 	{ },
@@ -73,8 +74,8 @@ static struct resource au1xxx_usb_ohci_resources[] = {
 		.flags		= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start		= AU1000_USB_HOST_INT,
-		.end		= AU1000_USB_HOST_INT,
+		.start		= FOR_PLATFORM_C_USB_HOST_INT,
+		.end		= FOR_PLATFORM_C_USB_HOST_INT,
 		.flags		= IORESOURCE_IRQ,
 	},
 };
@@ -132,8 +133,8 @@ static struct resource au1xxx_usb_ehci_resources[] = {
 		.flags		= IORESOURCE_MEM,
 	},
 	[1] = {
-		.start		= AU1000_USB_HOST_INT,
-		.end		= AU1000_USB_HOST_INT,
+		.start		= AU1200_USB_INT,
+		.end		= AU1200_USB_INT,
 		.flags		= IORESOURCE_IRQ,
 	},
 };
@@ -308,11 +309,6 @@ static struct platform_device au1200_mmc1_device = {
 #endif /* #ifndef CONFIG_MIPS_DB1200 */
 #endif /* #ifdef CONFIG_SOC_AU1200 */
 
-static struct platform_device au1x00_pcmcia_device = {
-	.name 		= "au1x00-pcmcia",
-	.id 		= 0,
-};
-
 /* All Alchemy demoboards with I2C have this #define in their headers */
 #ifdef SMBUS_PSC_BASE
 static struct resource pbdb_smbus_resources[] = {
@@ -331,10 +327,92 @@ static struct platform_device pbdb_smbus_device = {
 };
 #endif
 
+/* Macro to help defining the Ethernet MAC resources */
+#define MAC_RES(_base, _enable, _irq)			\
+	{						\
+		.start	= CPHYSADDR(_base),		\
+		.end	= CPHYSADDR(_base + 0xffff),	\
+		.flags	= IORESOURCE_MEM,		\
+	},						\
+	{						\
+		.start	= CPHYSADDR(_enable),		\
+		.end	= CPHYSADDR(_enable + 0x3),	\
+		.flags	= IORESOURCE_MEM,		\
+	},						\
+	{						\
+		.start	= _irq,				\
+		.end	= _irq,				\
+		.flags	= IORESOURCE_IRQ		\
+	}
+
+static struct resource au1xxx_eth0_resources[] = {
+#if defined(CONFIG_SOC_AU1000)
+	MAC_RES(AU1000_ETH0_BASE, AU1000_MAC0_ENABLE, AU1000_MAC0_DMA_INT),
+#elif defined(CONFIG_SOC_AU1100)
+	MAC_RES(AU1100_ETH0_BASE, AU1100_MAC0_ENABLE, AU1100_MAC0_DMA_INT),
+#elif defined(CONFIG_SOC_AU1550)
+	MAC_RES(AU1550_ETH0_BASE, AU1550_MAC0_ENABLE, AU1550_MAC0_DMA_INT),
+#elif defined(CONFIG_SOC_AU1500)
+	MAC_RES(AU1500_ETH0_BASE, AU1500_MAC0_ENABLE, AU1500_MAC0_DMA_INT),
+#endif
+};
+
+
+static struct au1000_eth_platform_data au1xxx_eth0_platform_data = {
+	.phy1_search_mac0 = 1,
+};
+
+static struct platform_device au1xxx_eth0_device = {
+	.name		= "au1000-eth",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(au1xxx_eth0_resources),
+	.resource	= au1xxx_eth0_resources,
+	.dev.platform_data = &au1xxx_eth0_platform_data,
+};
+
+#ifndef CONFIG_SOC_AU1100
+static struct resource au1xxx_eth1_resources[] = {
+#if defined(CONFIG_SOC_AU1000)
+	MAC_RES(AU1000_ETH1_BASE, AU1000_MAC1_ENABLE, AU1000_MAC1_DMA_INT),
+#elif defined(CONFIG_SOC_AU1550)
+	MAC_RES(AU1550_ETH1_BASE, AU1550_MAC1_ENABLE, AU1550_MAC1_DMA_INT),
+#elif defined(CONFIG_SOC_AU1500)
+	MAC_RES(AU1500_ETH1_BASE, AU1500_MAC1_ENABLE, AU1500_MAC1_DMA_INT),
+#endif
+};
+
+static struct au1000_eth_platform_data au1xxx_eth1_platform_data = {
+	.phy1_search_mac0 = 1,
+};
+
+static struct platform_device au1xxx_eth1_device = {
+	.name		= "au1000-eth",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(au1xxx_eth1_resources),
+	.resource	= au1xxx_eth1_resources,
+	.dev.platform_data = &au1xxx_eth1_platform_data,
+};
+#endif
+
+void __init au1xxx_override_eth_cfg(unsigned int port,
+			struct au1000_eth_platform_data *eth_data)
+{
+	if (!eth_data || port > 1)
+		return;
+
+	if (port == 0)
+		memcpy(&au1xxx_eth0_platform_data, eth_data,
+			sizeof(struct au1000_eth_platform_data));
+#ifndef CONFIG_SOC_AU1100
+	else
+		memcpy(&au1xxx_eth1_platform_data, eth_data,
+			sizeof(struct au1000_eth_platform_data));
+#endif
+}
+
 static struct platform_device *au1xxx_platform_devices[] __initdata = {
 	&au1xx0_uart_device,
 	&au1xxx_usb_ohci_device,
-	&au1x00_pcmcia_device,
 #ifdef CONFIG_FB_AU1100
 	&au1100_lcd_device,
 #endif
@@ -351,6 +429,7 @@ static struct platform_device *au1xxx_platform_devices[] __initdata = {
 #ifdef SMBUS_PSC_BASE
 	&pbdb_smbus_device,
 #endif
+	&au1xxx_eth0_device,
 };
 
 static int __init au1xxx_platform_init(void)
@@ -362,6 +441,12 @@ static int __init au1xxx_platform_init(void)
 	for (i = 0; au1x00_uart_data[i].flags; i++)
 		au1x00_uart_data[i].uartclk = uartclk;
 
+#ifndef CONFIG_SOC_AU1100
+	/* Register second MAC if enabled in pinfunc */
+	if (!(au_readl(SYS_PINFUNC) & (u32)SYS_PF_NI2))
+		platform_device_register(&au1xxx_eth1_device);
+#endif
+
 	return platform_add_devices(au1xxx_platform_devices,
 				    ARRAY_SIZE(au1xxx_platform_devices));
 }
diff --git a/arch/mips/alchemy/common/prom.c b/arch/mips/alchemy/common/prom.c
index 18b310b..c29511b 100644
--- a/arch/mips/alchemy/common/prom.c
+++ b/arch/mips/alchemy/common/prom.c
@@ -43,29 +43,15 @@ int prom_argc;
 char **prom_argv;
 char **prom_envp;
 
-char * __init_or_module prom_getcmdline(void)
-{
-	return &(arcs_cmdline[0]);
-}
-
 void prom_init_cmdline(void)
 {
-	char *cp;
-	int actr;
-
-	actr = 1; /* Always ignore argv[0] */
+	int i;
 
-	cp = &(arcs_cmdline[0]);
-	while (actr < prom_argc) {
-		strcpy(cp, prom_argv[actr]);
-		cp += strlen(prom_argv[actr]);
-		*cp++ = ' ';
-		actr++;
+	for (i = 1; i < prom_argc; i++) {
+		strlcat(arcs_cmdline, prom_argv[i], COMMAND_LINE_SIZE);
+		if (i < (prom_argc - 1))
+			strlcat(arcs_cmdline, " ", COMMAND_LINE_SIZE);
 	}
-	if (cp != &(arcs_cmdline[0])) /* get rid of trailing space */
-		--cp;
-	if (prom_argc > 1)
-		*cp = '\0';
 }
 
 char *prom_getenv(char *envname)
@@ -121,14 +107,12 @@ static inline void str2eaddr(unsigned char *ea, unsigned char *str)
 int prom_get_ethernet_addr(char *ethernet_addr)
 {
 	char *ethaddr_str;
-	char *argptr;
 
 	/* Check the environment variables first */
 	ethaddr_str = prom_getenv("ethaddr");
 	if (!ethaddr_str) {
 		/* Check command line */
-		argptr = prom_getcmdline();
-		ethaddr_str = strstr(argptr, "ethaddr=");
+		ethaddr_str = strstr(arcs_cmdline, "ethaddr=");
 		if (!ethaddr_str)
 			return -1;
 
diff --git a/arch/mips/alchemy/common/puts.c b/arch/mips/alchemy/common/puts.c
deleted file mode 100644
index 55bbe24..0000000
--- a/arch/mips/alchemy/common/puts.c
+++ /dev/null
@@ -1,68 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *	Low level UART routines to directly access Alchemy UART.
- *
- * Copyright 2001, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <asm/mach-au1x00/au1000.h>
-
-#define SERIAL_BASE   UART_BASE
-#define SER_CMD       0x7
-#define SER_DATA      0x1
-#define TX_BUSY       0x20
-
-#define TIMEOUT       0xffffff
-#define SLOW_DOWN
-
-static volatile unsigned long * const com1 = (unsigned long *)SERIAL_BASE;
-
-#ifdef SLOW_DOWN
-static inline void slow_down(void)
-{
-	int k;
-
-	for (k = 0; k < 10000; k++);
-}
-#else
-#define slow_down()
-#endif
-
-void
-prom_putchar(const unsigned char c)
-{
-	unsigned char ch;
-	int i = 0;
-
-	do {
-		ch = com1[SER_CMD];
-		slow_down();
-		i++;
-		if (i > TIMEOUT)
-			break;
-	} while (0 == (ch & TX_BUSY));
-
-	com1[SER_DATA] = c;
-}
diff --git a/arch/mips/alchemy/common/reset.c b/arch/mips/alchemy/common/reset.c
deleted file mode 100644
index 4791011..0000000
--- a/arch/mips/alchemy/common/reset.c
+++ /dev/null
@@ -1,188 +0,0 @@
-/*
- *
- * BRIEF MODULE DESCRIPTION
- *	Au1xx0 reset routines.
- *
- * Copyright 2001, 2006, 2008 MontaVista Software Inc.
- * Author: MontaVista Software, Inc. <source@mvista.com>
- *
- *  This program is free software; you can redistribute  it and/or modify it
- *  under  the terms of  the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the  License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
- *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
- *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/gpio.h>
-
-#include <asm/cacheflush.h>
-#include <asm/mach-au1x00/au1000.h>
-
-void au1000_restart(char *command)
-{
-	/* Set all integrated peripherals to disabled states */
-	extern void board_reset(void);
-	u32 prid = read_c0_prid();
-
-	printk(KERN_NOTICE "\n** Resetting Integrated Peripherals\n");
-
-	switch (prid & 0xFF000000) {
-	case 0x00000000: /* Au1000 */
-		au_writel(0x02, 0xb0000010); /* ac97_enable */
-		au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
-		asm("sync");
-		au_writel(0x00, 0xb017fffc); /* usbh_enable */
-		au_writel(0x00, 0xb0200058); /* usbd_enable */
-		au_writel(0x00, 0xb0300040); /* ir_enable */
-		au_writel(0x00, 0xb4004104); /* mac dma */
-		au_writel(0x00, 0xb4004114); /* mac dma */
-		au_writel(0x00, 0xb4004124); /* mac dma */
-		au_writel(0x00, 0xb4004134); /* mac dma */
-		au_writel(0x00, 0xb0520000); /* macen0 */
-		au_writel(0x00, 0xb0520004); /* macen1 */
-		au_writel(0x00, 0xb1000008); /* i2s_enable  */
-		au_writel(0x00, 0xb1100100); /* uart0_enable */
-		au_writel(0x00, 0xb1200100); /* uart1_enable */
-		au_writel(0x00, 0xb1300100); /* uart2_enable */
-		au_writel(0x00, 0xb1400100); /* uart3_enable */
-		au_writel(0x02, 0xb1600100); /* ssi0_enable */
-		au_writel(0x02, 0xb1680100); /* ssi1_enable */
-		au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
-		au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
-		au_writel(0x00, 0xb1900028); /* sys_clksrc */
-		au_writel(0x10, 0xb1900060); /* sys_cpupll */
-		au_writel(0x00, 0xb1900064); /* sys_auxpll */
-		au_writel(0x00, 0xb1900100); /* sys_pininputen */
-		break;
-	case 0x01000000: /* Au1500 */
-		au_writel(0x02, 0xb0000010); /* ac97_enable */
-		au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
-		asm("sync");
-		au_writel(0x00, 0xb017fffc); /* usbh_enable */
-		au_writel(0x00, 0xb0200058); /* usbd_enable */
-		au_writel(0x00, 0xb4004104); /* mac dma */
-		au_writel(0x00, 0xb4004114); /* mac dma */
-		au_writel(0x00, 0xb4004124); /* mac dma */
-		au_writel(0x00, 0xb4004134); /* mac dma */
-		au_writel(0x00, 0xb1520000); /* macen0 */
-		au_writel(0x00, 0xb1520004); /* macen1 */
-		au_writel(0x00, 0xb1100100); /* uart0_enable */
-		au_writel(0x00, 0xb1400100); /* uart3_enable */
-		au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
-		au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
-		au_writel(0x00, 0xb1900028); /* sys_clksrc */
-		au_writel(0x10, 0xb1900060); /* sys_cpupll */
-		au_writel(0x00, 0xb1900064); /* sys_auxpll */
-		au_writel(0x00, 0xb1900100); /* sys_pininputen */
-		break;
-	case 0x02000000: /* Au1100 */
-		au_writel(0x02, 0xb0000010); /* ac97_enable */
-		au_writel(0x08, 0xb017fffc); /* usbh_enable - early errata */
-		asm("sync");
-		au_writel(0x00, 0xb017fffc); /* usbh_enable */
-		au_writel(0x00, 0xb0200058); /* usbd_enable */
-		au_writel(0x00, 0xb0300040); /* ir_enable */
-		au_writel(0x00, 0xb4004104); /* mac dma */
-		au_writel(0x00, 0xb4004114); /* mac dma */
-		au_writel(0x00, 0xb4004124); /* mac dma */
-		au_writel(0x00, 0xb4004134); /* mac dma */
-		au_writel(0x00, 0xb0520000); /* macen0 */
-		au_writel(0x00, 0xb1000008); /* i2s_enable  */
-		au_writel(0x00, 0xb1100100); /* uart0_enable */
-		au_writel(0x00, 0xb1200100); /* uart1_enable */
-		au_writel(0x00, 0xb1400100); /* uart3_enable */
-		au_writel(0x02, 0xb1600100); /* ssi0_enable */
-		au_writel(0x02, 0xb1680100); /* ssi1_enable */
-		au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
-		au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
-		au_writel(0x00, 0xb1900028); /* sys_clksrc */
-		au_writel(0x10, 0xb1900060); /* sys_cpupll */
-		au_writel(0x00, 0xb1900064); /* sys_auxpll */
-		au_writel(0x00, 0xb1900100); /* sys_pininputen */
-		break;
-	case 0x03000000: /* Au1550 */
-		au_writel(0x00, 0xb1a00004); /* psc 0 */
-		au_writel(0x00, 0xb1b00004); /* psc 1 */
-		au_writel(0x00, 0xb0a00004); /* psc 2 */
-		au_writel(0x00, 0xb0b00004); /* psc 3 */
-		au_writel(0x00, 0xb017fffc); /* usbh_enable */
-		au_writel(0x00, 0xb0200058); /* usbd_enable */
-		au_writel(0x00, 0xb4004104); /* mac dma */
-		au_writel(0x00, 0xb4004114); /* mac dma */
-		au_writel(0x00, 0xb4004124); /* mac dma */
-		au_writel(0x00, 0xb4004134); /* mac dma */
-		au_writel(0x00, 0xb1520000); /* macen0 */
-		au_writel(0x00, 0xb1520004); /* macen1 */
-		au_writel(0x00, 0xb1100100); /* uart0_enable */
-		au_writel(0x00, 0xb1200100); /* uart1_enable */
-		au_writel(0x00, 0xb1400100); /* uart3_enable */
-		au_writel(0x00, 0xb1900020); /* sys_freqctrl0 */
-		au_writel(0x00, 0xb1900024); /* sys_freqctrl1 */
-		au_writel(0x00, 0xb1900028); /* sys_clksrc */
-		au_writel(0x10, 0xb1900060); /* sys_cpupll */
-		au_writel(0x00, 0xb1900064); /* sys_auxpll */
-		au_writel(0x00, 0xb1900100); /* sys_pininputen */
-		break;
-	}
-
-	set_c0_status(ST0_BEV | ST0_ERL);
-	change_c0_config(CONF_CM_CMASK, CONF_CM_UNCACHED);
-	flush_cache_all();
-	write_c0_wired(0);
-
-	/* Give board a chance to do a hardware reset */
-	board_reset();
-
-	/* Jump to the beggining in case board_reset() is empty */
-	__asm__ __volatile__("jr\t%0"::"r"(0xbfc00000));
-}
-
-void au1000_halt(void)
-{
-#if defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550)
-	/* Power off system */
-	printk(KERN_NOTICE "\n** Powering off...\n");
-	au_writew(au_readw(0xAF00001C) | (3 << 14), 0xAF00001C);
-	au_sync();
-	while (1); /* should not get here */
-#else
-	printk(KERN_NOTICE "\n** You can safely turn off the power\n");
-#ifdef CONFIG_MIPS_MIRAGE
-	gpio_direction_output(210, 1);
-#endif
-#ifdef CONFIG_MIPS_DB1200
-	au_writew(au_readw(0xB980001C) | (1 << 14), 0xB980001C);
-#endif
-#ifdef CONFIG_PM
-	au_sleep();
-
-	/* Should not get here */
-	printk(KERN_ERR "Unable to put CPU in sleep mode\n");
-	while (1);
-#else
-	while (1)
-		__asm__(".set\tmips3\n\t"
-	                "wait\n\t"
-			".set\tmips0");
-#endif
-#endif /* defined(CONFIG_MIPS_PB1550) || defined(CONFIG_MIPS_DB1550) */
-}
-
-void au1000_power_off(void)
-{
-	au1000_halt();
-}
diff --git a/arch/mips/alchemy/common/setup.c b/arch/mips/alchemy/common/setup.c
index 6184baa..561e5da 100644
--- a/arch/mips/alchemy/common/setup.c
+++ b/arch/mips/alchemy/common/setup.c
@@ -29,18 +29,13 @@
 #include <linux/ioport.h>
 #include <linux/jiffies.h>
 #include <linux/module.h>
-#include <linux/pm.h>
 
 #include <asm/mipsregs.h>
-#include <asm/reboot.h>
 #include <asm/time.h>
 
 #include <au1000.h>
 
 extern void __init board_setup(void);
-extern void au1000_restart(char *);
-extern void au1000_halt(void);
-extern void au1000_power_off(void);
 extern void set_cpuspec(void);
 
 void __init plat_mem_setup(void)
@@ -57,10 +52,6 @@ void __init plat_mem_setup(void)
 	/* this is faster than wasting cycles trying to approximate it */
 	preset_lpj = (est_freq >> 1) / HZ;
 
-	_machine_restart = au1000_restart;
-	_machine_halt = au1000_halt;
-	pm_power_off = au1000_power_off;
-
 	board_setup();  /* board specific setup */
 
 	if (au1xxx_cpu_needs_config_od())
@@ -78,37 +69,20 @@ void __init plat_mem_setup(void)
 	iomem_resource.end = IOMEM_RESOURCE_END;
 }
 
-#if defined(CONFIG_64BIT_PHYS_ADDR)
+#if defined(CONFIG_64BIT_PHYS_ADDR) && defined(CONFIG_PCI)
 /* This routine should be valid for all Au1x based boards */
 phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
 {
+	u32 start = (u32)Au1500_PCI_MEM_START;
+	u32 end   = (u32)Au1500_PCI_MEM_END;
+
 	/* Don't fixup 36-bit addresses */
 	if ((phys_addr >> 32) != 0)
 		return phys_addr;
 
-#ifdef CONFIG_PCI
-	{
-		u32 start = (u32)Au1500_PCI_MEM_START;
-		u32 end   = (u32)Au1500_PCI_MEM_END;
-
-		/* Check for PCI memory window */
-		if (phys_addr >= start && (phys_addr + size - 1) <= end)
-			return (phys_t)
-			       ((phys_addr - start) + Au1500_PCI_MEM_START);
-	}
-#endif
-
-	/*
-	 * All Au1xx0 SOCs have a PCMCIA controller.
-	 * We setup our 32-bit pseudo addresses to be equal to the
-	 * 36-bit addr >> 4, to make it easier to check the address
-	 * and fix it.
-	 * The PCMCIA socket 0 physical attribute address is 0xF 4000 0000.
-	 * The pseudo address we use is 0xF400 0000. Any address over
-	 * 0xF400 0000 is a PCMCIA pseudo address.
-	 */
-	if ((phys_addr >= 0xF4000000) && (phys_addr < 0xFFFFFFFF))
-		return (phys_t)(phys_addr << 4);
+	/* Check for PCI memory window */
+	if (phys_addr >= start && (phys_addr + size - 1) <= end)
+		return (phys_t)((phys_addr - start) + Au1500_PCI_MEM_START);
 
 	/* default nop */
 	return phys_addr;
diff --git a/arch/mips/alchemy/common/time.c b/arch/mips/alchemy/common/time.c
index 379a664..2aecb2f 100644
--- a/arch/mips/alchemy/common/time.c
+++ b/arch/mips/alchemy/common/time.c
@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2008 Manuel Lauss <mano@roarinelk.homelinux.net>
+ * Copyright (C) 2008-2009 Manuel Lauss <manuel.lauss@gmail.com>
  *
  * Previous incarnations were:
  * Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
@@ -85,7 +85,6 @@ static struct clock_event_device au1x_rtcmatch2_clockdev = {
 	.name		= "rtcmatch2",
 	.features	= CLOCK_EVT_FEAT_ONESHOT,
 	.rating		= 100,
-	.irq		= AU1000_RTC_MATCH2_INT,
 	.set_next_event	= au1x_rtcmatch2_set_next_event,
 	.set_mode	= au1x_rtcmatch2_set_mode,
 	.cpumask	= cpu_all_mask,
@@ -98,11 +97,13 @@ static struct irqaction au1x_rtcmatch2_irqaction = {
 	.dev_id		= &au1x_rtcmatch2_clockdev,
 };
 
-void __init plat_time_init(void)
+static int __init alchemy_time_init(unsigned int m2int)
 {
 	struct clock_event_device *cd = &au1x_rtcmatch2_clockdev;
 	unsigned long t;
 
+	au1x_rtcmatch2_clockdev.irq = m2int;
+
 	/* Check if firmware (YAMON, ...) has enabled 32kHz and clock
 	 * has been detected.  If so install the rtcmatch2 clocksource,
 	 * otherwise don't bother.  Note that both bits being set is by
@@ -148,13 +149,18 @@ void __init plat_time_init(void)
 	cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
 	cd->min_delta_ns = clockevent_delta2ns(8, cd);	/* ~0.25ms */
 	clockevents_register_device(cd);
-	setup_irq(AU1000_RTC_MATCH2_INT, &au1x_rtcmatch2_irqaction);
+	setup_irq(m2int, &au1x_rtcmatch2_irqaction);
 
 	printk(KERN_INFO "Alchemy clocksource installed\n");
 
-	return;
+	return 0;
 
 cntr_err:
+	return -1;
+}
+
+static void __init alchemy_setup_c0timer(void)
+{
 	/*
 	 * MIPS kernel assigns 'au1k_wait' to 'cpu_wait' before this
 	 * function is called.  Because the Alchemy counters are unusable
@@ -166,3 +172,22 @@ cntr_err:
 	r4k_clockevent_init();
 	init_r4k_clocksource();
 }
+
+static int alchemy_m2inttab[] __initdata = {
+	AU1000_RTC_MATCH2_INT,
+	AU1500_RTC_MATCH2_INT,
+	AU1100_RTC_MATCH2_INT,
+	AU1550_RTC_MATCH2_INT,
+	AU1200_RTC_MATCH2_INT,
+};
+
+void __init plat_time_init(void)
+{
+	int t;
+
+	t = alchemy_get_cputype();
+	if (t == ALCHEMY_CPU_UNKNOWN)
+		alchemy_setup_c0timer();
+	else if (alchemy_time_init(alchemy_m2inttab[t]))
+		alchemy_setup_c0timer();
+}
diff --git a/arch/mips/alchemy/devboards/Makefile b/arch/mips/alchemy/devboards/Makefile
index 730f9f2..ecbd37f 100644
--- a/arch/mips/alchemy/devboards/Makefile
+++ b/arch/mips/alchemy/devboards/Makefile
@@ -2,7 +2,7 @@
 # Alchemy Develboards
 #
 
-obj-y += prom.o
+obj-y += prom.o bcsr.o platform.o
 obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_MIPS_PB1000)	+= pb1000/
 obj-$(CONFIG_MIPS_PB1100)	+= pb1100/
@@ -11,8 +11,10 @@ obj-$(CONFIG_MIPS_PB1500)	+= pb1500/
 obj-$(CONFIG_MIPS_PB1550)	+= pb1550/
 obj-$(CONFIG_MIPS_DB1000)	+= db1x00/
 obj-$(CONFIG_MIPS_DB1100)	+= db1x00/
-obj-$(CONFIG_MIPS_DB1200)	+= pb1200/
+obj-$(CONFIG_MIPS_DB1200)	+= db1200/
 obj-$(CONFIG_MIPS_DB1500)	+= db1x00/
 obj-$(CONFIG_MIPS_DB1550)	+= db1x00/
 obj-$(CONFIG_MIPS_BOSPORUS)	+= db1x00/
 obj-$(CONFIG_MIPS_MIRAGE)	+= db1x00/
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/devboards/bcsr.c b/arch/mips/alchemy/devboards/bcsr.c
new file mode 100644
index 0000000..3bc4fd2
--- /dev/null
+++ b/arch/mips/alchemy/devboards/bcsr.c
@@ -0,0 +1,148 @@
+/*
+ * bcsr.h -- Db1xxx/Pb1xxx Devboard CPLD registers ("BCSR") abstraction.
+ *
+ * All Alchemy development boards (except, of course, the weird PB1000)
+ * have a few registers in a CPLD with standardised layout; they mostly
+ * only differ in base address.
+ * All registers are 16bits wide with 32bit spacing.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <asm/addrspace.h>
+#include <asm/io.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+static struct bcsr_reg {
+	void __iomem *raddr;
+	spinlock_t lock;
+} bcsr_regs[BCSR_CNT];
+
+static void __iomem *bcsr_virt;	/* KSEG1 addr of BCSR base */
+static int bcsr_csc_base;	/* linux-irq of first cascaded irq */
+
+void __init bcsr_init(unsigned long bcsr1_phys, unsigned long bcsr2_phys)
+{
+	int i;
+
+	bcsr1_phys = KSEG1ADDR(CPHYSADDR(bcsr1_phys));
+	bcsr2_phys = KSEG1ADDR(CPHYSADDR(bcsr2_phys));
+
+	bcsr_virt = (void __iomem *)bcsr1_phys;
+
+	for (i = 0; i < BCSR_CNT; i++) {
+		if (i >= BCSR_HEXLEDS)
+			bcsr_regs[i].raddr = (void __iomem *)bcsr2_phys +
+					(0x04 * (i - BCSR_HEXLEDS));
+		else
+			bcsr_regs[i].raddr = (void __iomem *)bcsr1_phys +
+					(0x04 * i);
+
+		spin_lock_init(&bcsr_regs[i].lock);
+	}
+}
+
+unsigned short bcsr_read(enum bcsr_id reg)
+{
+	unsigned short r;
+	unsigned long flags;
+
+	spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+	r = __raw_readw(bcsr_regs[reg].raddr);
+	spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+	return r;
+}
+EXPORT_SYMBOL_GPL(bcsr_read);
+
+void bcsr_write(enum bcsr_id reg, unsigned short val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+	__raw_writew(val, bcsr_regs[reg].raddr);
+	wmb();
+	spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+}
+EXPORT_SYMBOL_GPL(bcsr_write);
+
+void bcsr_mod(enum bcsr_id reg, unsigned short clr, unsigned short set)
+{
+	unsigned short r;
+	unsigned long flags;
+
+	spin_lock_irqsave(&bcsr_regs[reg].lock, flags);
+	r = __raw_readw(bcsr_regs[reg].raddr);
+	r &= ~clr;
+	r |= set;
+	__raw_writew(r, bcsr_regs[reg].raddr);
+	wmb();
+	spin_unlock_irqrestore(&bcsr_regs[reg].lock, flags);
+}
+EXPORT_SYMBOL_GPL(bcsr_mod);
+
+/*
+ * DB1200/PB1200 CPLD IRQ muxer
+ */
+static void bcsr_csc_handler(unsigned int irq, struct irq_desc *d)
+{
+	unsigned short bisr = __raw_readw(bcsr_virt + BCSR_REG_INTSTAT);
+
+	for ( ; bisr; bisr &= bisr - 1)
+		generic_handle_irq(bcsr_csc_base + __ffs(bisr));
+}
+
+/* NOTE: both the enable and mask bits must be cleared, otherwise the
+ * CPLD generates tons of spurious interrupts (at least on my DB1200).
+ *	-- mlau
+ */
+static void bcsr_irq_mask(unsigned int irq_nr)
+{
+	unsigned short v = 1 << (irq_nr - bcsr_csc_base);
+	__raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
+	__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
+	wmb();
+}
+
+static void bcsr_irq_maskack(unsigned int irq_nr)
+{
+	unsigned short v = 1 << (irq_nr - bcsr_csc_base);
+	__raw_writew(v, bcsr_virt + BCSR_REG_INTCLR);
+	__raw_writew(v, bcsr_virt + BCSR_REG_MASKCLR);
+	__raw_writew(v, bcsr_virt + BCSR_REG_INTSTAT);	/* ack */
+	wmb();
+}
+
+static void bcsr_irq_unmask(unsigned int irq_nr)
+{
+	unsigned short v = 1 << (irq_nr - bcsr_csc_base);
+	__raw_writew(v, bcsr_virt + BCSR_REG_INTSET);
+	__raw_writew(v, bcsr_virt + BCSR_REG_MASKSET);
+	wmb();
+}
+
+static struct irq_chip bcsr_irq_type = {
+	.name		= "CPLD",
+	.mask		= bcsr_irq_mask,
+	.mask_ack	= bcsr_irq_maskack,
+	.unmask		= bcsr_irq_unmask,
+};
+
+void __init bcsr_init_irq(int csc_start, int csc_end, int hook_irq)
+{
+	unsigned int irq;
+
+	/* mask & disable & ack all */
+	__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTCLR);
+	__raw_writew(0xffff, bcsr_virt + BCSR_REG_MASKCLR);
+	__raw_writew(0xffff, bcsr_virt + BCSR_REG_INTSTAT);
+	wmb();
+
+	bcsr_csc_base = csc_start;
+
+	for (irq = csc_start; irq <= csc_end; irq++)
+		set_irq_chip_and_handler_name(irq, &bcsr_irq_type,
+			handle_level_irq, "level");
+
+	set_irq_chained_handler(hook_irq, bcsr_csc_handler);
+}
diff --git a/arch/mips/alchemy/devboards/db1200/Makefile b/arch/mips/alchemy/devboards/db1200/Makefile
new file mode 100644
index 0000000..17840a5
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200/Makefile
@@ -0,0 +1 @@
+obj-y += setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1200/platform.c b/arch/mips/alchemy/devboards/db1200/platform.c
new file mode 100644
index 0000000..3cb95a9
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200/platform.c
@@ -0,0 +1,561 @@
+/*
+ * DBAu1200 board platform device registration
+ *
+ * Copyright (C) 2008-2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/partitions.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/smc91x.h>
+
+#include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-au1x00/au1xxx_dbdma.h>
+#include <asm/mach-au1x00/au1550_spi.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-db1x00/db1200.h>
+
+#include "../platform.h"
+
+static struct mtd_partition db1200_spiflash_parts[] = {
+	{
+		.name	= "DB1200 SPI flash",
+		.offset	= 0,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct flash_platform_data db1200_spiflash_data = {
+	.name		= "s25fl001",
+	.parts		= db1200_spiflash_parts,
+	.nr_parts	= ARRAY_SIZE(db1200_spiflash_parts),
+	.type		= "m25p10",
+};
+
+static struct spi_board_info db1200_spi_devs[] __initdata = {
+	{
+		/* TI TMP121AIDBVR temp sensor */
+		.modalias	= "tmp121",
+		.max_speed_hz	= 2000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= 0,
+	},
+	{
+		/* Spansion S25FL001D0FMA SPI flash */
+		.modalias	= "m25p80",
+		.max_speed_hz	= 50000000,
+		.bus_num	= 0,
+		.chip_select	= 1,
+		.mode		= 0,
+		.platform_data	= &db1200_spiflash_data,
+	},
+};
+
+static struct i2c_board_info db1200_i2c_devs[] __initdata = {
+	{
+		/* AT24C04-10 I2C eeprom */
+		I2C_BOARD_INFO("24c04", 0x52),
+	},
+	{
+		/* Philips NE1619 temp/voltage sensor (adm1025 drv) */
+		I2C_BOARD_INFO("ne1619", 0x2d),
+	},
+	{
+		/* I2S audio codec WM8731 */
+		I2C_BOARD_INFO("wm8731", 0x1b),
+	},
+};
+
+/**********************************************************************/
+
+static void au1200_nand_cmd_ctrl(struct mtd_info *mtd, int cmd,
+				 unsigned int ctrl)
+{
+	struct nand_chip *this = mtd->priv;
+	unsigned long ioaddr = (unsigned long)this->IO_ADDR_W;
+
+	ioaddr &= 0xffffff00;
+
+	if (ctrl & NAND_CLE) {
+		ioaddr += MEM_STNAND_CMD;
+	} else if (ctrl & NAND_ALE) {
+		ioaddr += MEM_STNAND_ADDR;
+	} else {
+		/* assume we want to r/w real data  by default */
+		ioaddr += MEM_STNAND_DATA;
+	}
+	this->IO_ADDR_R = this->IO_ADDR_W = (void __iomem *)ioaddr;
+	if (cmd != NAND_CMD_NONE) {
+		__raw_writeb(cmd, this->IO_ADDR_W);
+		wmb();
+	}
+}
+
+static int au1200_nand_device_ready(struct mtd_info *mtd)
+{
+	return __raw_readl((void __iomem *)MEM_STSTAT) & 1;
+}
+
+static const char *db1200_part_probes[] = { "cmdlinepart", NULL };
+
+static struct mtd_partition db1200_nand_parts[] = {
+	{
+		.name	= "NAND FS 0",
+		.offset	= 0,
+		.size	= 8 * 1024 * 1024,
+	},
+	{
+		.name	= "NAND FS 1",
+		.offset	= MTDPART_OFS_APPEND,
+		.size	= MTDPART_SIZ_FULL
+	},
+};
+
+struct platform_nand_data db1200_nand_platdata = {
+	.chip = {
+		.nr_chips	= 1,
+		.chip_offset	= 0,
+		.nr_partitions	= ARRAY_SIZE(db1200_nand_parts),
+		.partitions	= db1200_nand_parts,
+		.chip_delay	= 20,
+		.part_probe_types = db1200_part_probes,
+	},
+	.ctrl = {
+		.dev_ready	= au1200_nand_device_ready,
+		.cmd_ctrl	= au1200_nand_cmd_ctrl,
+	},
+};
+
+static struct resource db1200_nand_res[] = {
+	[0] = {
+		.start	= DB1200_NAND_PHYS_ADDR,
+		.end	= DB1200_NAND_PHYS_ADDR + 0xff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device db1200_nand_dev = {
+	.name		= "gen_nand",
+	.num_resources	= ARRAY_SIZE(db1200_nand_res),
+	.resource	= db1200_nand_res,
+	.id		= -1,
+	.dev		= {
+		.platform_data = &db1200_nand_platdata,
+	}
+};
+
+/**********************************************************************/
+
+static struct smc91x_platdata db1200_eth_data = {
+	.flags	= SMC91X_NOWAIT | SMC91X_USE_16BIT,
+	.leda	= RPC_LED_100_10,
+	.ledb	= RPC_LED_TX_RX,
+};
+
+static struct resource db1200_eth_res[] = {
+	[0] = {
+		.start	= DB1200_ETH_PHYS_ADDR,
+		.end	= DB1200_ETH_PHYS_ADDR + 0xf,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= DB1200_ETH_INT,
+		.end	= DB1200_ETH_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device db1200_eth_dev = {
+	.dev	= {
+		.platform_data	= &db1200_eth_data,
+	},
+	.name		= "smc91x",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(db1200_eth_res),
+	.resource	= db1200_eth_res,
+};
+
+/**********************************************************************/
+
+static struct resource db1200_ide_res[] = {
+	[0] = {
+		.start	= DB1200_IDE_PHYS_ADDR,
+		.end 	= DB1200_IDE_PHYS_ADDR + DB1200_IDE_PHYS_LEN - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= DB1200_IDE_INT,
+		.end	= DB1200_IDE_INT,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static u64 ide_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device db1200_ide_dev = {
+	.name		= "au1200-ide",
+	.id		= 0,
+	.dev = {
+		.dma_mask 		= &ide_dmamask,
+		.coherent_dma_mask	= DMA_32BIT_MASK,
+	},
+	.num_resources	= ARRAY_SIZE(db1200_ide_res),
+	.resource	= db1200_ide_res,
+};
+
+/**********************************************************************/
+
+static struct platform_device db1200_rtc_dev = {
+	.name	= "rtc-au1xxx",
+	.id	= -1,
+};
+
+/**********************************************************************/
+
+/* SD carddetects:  they're supposed to be edge-triggered, but ack
+ * doesn't seem to work (CPLD Rev 2).  Instead, the screaming one
+ * is disabled and its counterpart enabled.  The 500ms timeout is
+ * because the carddetect isn't debounced in hardware.
+ */
+static irqreturn_t db1200_mmc_cd(int irq, void *ptr)
+{
+	void(*mmc_cd)(struct mmc_host *, unsigned long);
+
+	if (irq == DB1200_SD0_INSERT_INT) {
+		disable_irq_nosync(DB1200_SD0_INSERT_INT);
+		enable_irq(DB1200_SD0_EJECT_INT);
+	} else {
+		disable_irq_nosync(DB1200_SD0_EJECT_INT);
+		enable_irq(DB1200_SD0_INSERT_INT);
+	}
+
+	/* link against CONFIG_MMC=m */
+	mmc_cd = symbol_get(mmc_detect_change);
+	if (mmc_cd) {
+		mmc_cd(ptr, msecs_to_jiffies(500));
+		symbol_put(mmc_detect_change);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int db1200_mmc_cd_setup(void *mmc_host, int en)
+{
+	int ret;
+
+	if (en) {
+		ret = request_irq(DB1200_SD0_INSERT_INT, db1200_mmc_cd,
+				  IRQF_DISABLED, "sd_insert", mmc_host);
+		if (ret)
+			goto out;
+
+		ret = request_irq(DB1200_SD0_EJECT_INT, db1200_mmc_cd,
+				  IRQF_DISABLED, "sd_eject", mmc_host);
+		if (ret) {
+			free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+			goto out;
+		}
+
+		if (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT)
+			enable_irq(DB1200_SD0_EJECT_INT);
+		else
+			enable_irq(DB1200_SD0_INSERT_INT);
+
+	} else {
+		free_irq(DB1200_SD0_INSERT_INT, mmc_host);
+		free_irq(DB1200_SD0_EJECT_INT, mmc_host);
+	}
+	ret = 0;
+out:
+	return ret;
+}
+
+static void db1200_mmc_set_power(void *mmc_host, int state)
+{
+	if (state) {
+		bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
+		msleep(400);	/* stabilization time */
+	} else
+		bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
+}
+
+static int db1200_mmc_card_readonly(void *mmc_host)
+{
+	return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
+}
+
+static int db1200_mmc_card_inserted(void *mmc_host)
+{
+	return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
+}
+
+static void db1200_mmcled_set(struct led_classdev *led,
+			      enum led_brightness brightness)
+{
+	if (brightness != LED_OFF)
+		bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
+	else
+		bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
+}
+
+static struct led_classdev db1200_mmc_led = {
+	.brightness_set	= db1200_mmcled_set,
+};
+
+/* needed by arch/mips/alchemy/common/platform.c */
+struct au1xmmc_platform_data au1xmmc_platdata[] = {
+	[0] = {
+		.cd_setup	= db1200_mmc_cd_setup,
+		.set_power	= db1200_mmc_set_power,
+		.card_inserted	= db1200_mmc_card_inserted,
+		.card_readonly	= db1200_mmc_card_readonly,
+		.led		= &db1200_mmc_led,
+	},
+};
+
+/**********************************************************************/
+
+static struct resource au1200_psc0_res[] = {
+	[0] = {
+		.start	= PSC0_PHYS_ADDR,
+		.end	= PSC0_PHYS_ADDR + 0x000fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1200_PSC0_INT,
+		.end	= AU1200_PSC0_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= DSCR_CMD0_PSC0_TX,
+		.end	= DSCR_CMD0_PSC0_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= DSCR_CMD0_PSC0_RX,
+		.end	= DSCR_CMD0_PSC0_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1200_i2c_dev = {
+	.name		= "au1xpsc_smbus",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1200_psc0_res),
+	.resource	= au1200_psc0_res,
+};
+
+static void db1200_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
+{
+	if (cs)
+		bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_SPISEL);
+	else
+		bcsr_mod(BCSR_RESETS, BCSR_RESETS_SPISEL, 0);
+}
+
+static struct au1550_spi_info db1200_spi_platdata = {
+	.mainclk_hz	= 50000000,	/* PSC0 clock */
+	.num_chipselect = 2,
+	.activate_cs	= db1200_spi_cs_en,
+};
+
+static u64 spi_dmamask = DMA_32BIT_MASK;
+
+static struct platform_device db1200_spi_dev = {
+	.dev	= {
+		.dma_mask		= &spi_dmamask,
+		.coherent_dma_mask	= DMA_32BIT_MASK,
+		.platform_data		= &db1200_spi_platdata,
+	},
+	.name		= "au1550-spi",
+	.id		= 0,	/* bus number */
+	.num_resources	= ARRAY_SIZE(au1200_psc0_res),
+	.resource	= au1200_psc0_res,
+};
+
+static struct resource au1200_psc1_res[] = {
+	[0] = {
+		.start	= PSC1_PHYS_ADDR,
+		.end	= PSC1_PHYS_ADDR + 0x000fffff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1200_PSC1_INT,
+		.end	= AU1200_PSC1_INT,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.start	= DSCR_CMD0_PSC1_TX,
+		.end	= DSCR_CMD0_PSC1_TX,
+		.flags	= IORESOURCE_DMA,
+	},
+	[3] = {
+		.start	= DSCR_CMD0_PSC1_RX,
+		.end	= DSCR_CMD0_PSC1_RX,
+		.flags	= IORESOURCE_DMA,
+	},
+};
+
+static struct platform_device db1200_audio_dev = {
+	/* name assigned later based on switch setting */
+	.id		= 1,	/* PSC ID */
+	.num_resources	= ARRAY_SIZE(au1200_psc1_res),
+	.resource	= au1200_psc1_res,
+};
+
+static struct platform_device *db1200_devs[] __initdata = {
+	NULL,		/* PSC0, selected by S6.8 */
+	&db1200_ide_dev,
+	&db1200_eth_dev,
+	&db1200_rtc_dev,
+	&db1200_nand_dev,
+	&db1200_audio_dev,
+};
+
+static int __init db1200_dev_init(void)
+{
+	unsigned long pfc;
+	unsigned short sw;
+	int swapped;
+
+	i2c_register_board_info(0, db1200_i2c_devs,
+				ARRAY_SIZE(db1200_i2c_devs));
+	spi_register_board_info(db1200_spi_devs,
+				ARRAY_SIZE(db1200_i2c_devs));
+
+	/* SWITCHES:	S6.8 I2C/SPI selector  (OFF=I2C  ON=SPI)
+	 *		S6.7 AC97/I2S selector (OFF=AC97 ON=I2S)
+	 */
+
+	/* NOTE: GPIO215 controls OTG VBUS supply.  In SPI mode however
+	 * this pin is claimed by PSC0 (unused though, but pinmux doesn't
+	 * allow to free it without crippling the SPI interface).
+	 * As a result, in SPI mode, OTG simply won't work (PSC0 uses
+	 * it as an input pin which is pulled high on the boards).
+	 */
+	pfc = __raw_readl((void __iomem *)SYS_PINFUNC) & ~SYS_PINFUNC_P0A;
+
+	/* switch off OTG VBUS supply */
+	gpio_request(215, "otg-vbus");
+	gpio_direction_output(215, 1);
+
+	printk(KERN_INFO "DB1200 device configuration:\n");
+
+	sw = bcsr_read(BCSR_SWITCHES);
+	if (sw & BCSR_SWITCHES_DIP_8) {
+		db1200_devs[0] = &db1200_i2c_dev;
+		bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
+
+		pfc |= (2 << 17);	/* GPIO2 block owns GPIO215 */
+
+		printk(KERN_INFO " S6.8 OFF: PSC0 mode I2C\n");
+		printk(KERN_INFO "   OTG port VBUS supply available!\n");
+	} else {
+		db1200_devs[0] = &db1200_spi_dev;
+		bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC0MUX);
+
+		pfc |= (1 << 17);	/* PSC0 owns GPIO215 */
+
+		printk(KERN_INFO " S6.8 ON : PSC0 mode SPI\n");
+		printk(KERN_INFO "   OTG port VBUS supply disabled\n");
+	}
+	__raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+	wmb();
+
+	/* Audio: DIP7 selects I2S(0)/AC97(1), but need I2C for I2S!
+	 * so: DIP7=1 || DIP8=0 => AC97, DIP7=0 && DIP8=1 => I2S
+	 */
+	sw &= BCSR_SWITCHES_DIP_8 | BCSR_SWITCHES_DIP_7;
+	if (sw == BCSR_SWITCHES_DIP_8) {
+		bcsr_mod(BCSR_RESETS, 0, BCSR_RESETS_PSC1MUX);
+		db1200_audio_dev.name = "au1xpsc_i2s";
+		printk(KERN_INFO " S6.7 ON : PSC1 mode I2S\n");
+	} else {
+		bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC1MUX, 0);
+		db1200_audio_dev.name = "au1xpsc_ac97";
+		printk(KERN_INFO " S6.7 OFF: PSC1 mode AC97\n");
+	}
+
+	/* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
+	__raw_writel(PSC_SEL_CLK_SERCLK,
+		(void __iomem *)KSEG1ADDR(PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
+	wmb();
+
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR,
+				    PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+				    DB1200_PC0_INT,
+				    DB1200_PC0_INSERT_INT,
+				    /*DB1200_PC0_STSCHG_INT*/0,
+				    DB1200_PC0_EJECT_INT,
+				    0);
+
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR   + 0x004000000,
+				    PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
+				    DB1200_PC1_INT,
+				    DB1200_PC1_INSERT_INT,
+				    /*DB1200_PC1_STSCHG_INT*/0,
+				    DB1200_PC1_EJECT_INT,
+				    1);
+
+	swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1200_SWAPBOOT;
+	db1x_register_norflash(64 << 20, 2, swapped);
+
+	return platform_add_devices(db1200_devs, ARRAY_SIZE(db1200_devs));
+}
+device_initcall(db1200_dev_init);
+
+/* au1200fb calls these: STERBT EINEN TRAGISCHEN TOD!!! */
+int board_au1200fb_panel(void)
+{
+	return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
+}
+
+int board_au1200fb_panel_init(void)
+{
+	/* Apply power */
+	bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+				BCSR_BOARD_LCDBL);
+	return 0;
+}
+
+int board_au1200fb_panel_shutdown(void)
+{
+	/* Remove power */
+	bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+			     BCSR_BOARD_LCDBL, 0);
+	return 0;
+}
diff --git a/arch/mips/alchemy/devboards/db1200/setup.c b/arch/mips/alchemy/devboards/db1200/setup.c
new file mode 100644
index 0000000..379536e
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1200/setup.c
@@ -0,0 +1,118 @@
+/*
+ * Alchemy/AMD/RMI DB1200 board setup.
+ *
+ * Licensed under the terms outlined in the file COPYING in the root of
+ * this source archive.
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-db1x00/db1200.h>
+
+const char *get_system_type(void)
+{
+	return "Alchemy Db1200";
+}
+
+void __init board_setup(void)
+{
+	unsigned long freq0, clksrc, div, pfc;
+	unsigned short whoami;
+
+	bcsr_init(DB1200_BCSR_PHYS_ADDR,
+		  DB1200_BCSR_PHYS_ADDR + DB1200_BCSR_HEXLED_OFS);
+
+	whoami = bcsr_read(BCSR_WHOAMI);
+	printk(KERN_INFO "Alchemy/AMD/RMI DB1200 Board, CPLD Rev %d"
+		"  Board-ID %d  Daughtercard ID %d\n",
+		(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
+
+	/* SMBus/SPI on PSC0, Audio on PSC1 */
+	pfc = __raw_readl((void __iomem *)SYS_PINFUNC);
+	pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
+	pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
+	pfc |= SYS_PINFUNC_P1C;	/* SPI is configured later */
+	__raw_writel(pfc, (void __iomem *)SYS_PINFUNC);
+	wmb();
+
+	/* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
+	 * CPU clock; all other clock generators off/unused.
+	 */
+	div = (get_au1x00_speed() + 25000000) / 50000000;
+	if (div & 1)
+		div++;
+	div = ((div >> 1) - 1) & 0xff;
+
+	freq0 = div << SYS_FC_FRDIV0_BIT;
+	__raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+	wmb();
+	freq0 |= SYS_FC_FE0;	/* enable F0 */
+	__raw_writel(freq0, (void __iomem *)SYS_FREQCTRL0);
+	wmb();
+
+	/* psc0_intclk comes 1:1 from F0 */
+	clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
+	__raw_writel(clksrc, (void __iomem *)SYS_CLKSRC);
+	wmb();
+}
+
+/* use the hexleds to count the number of times the cpu has entered
+ * wait, the dots to indicate whether the CPU is currently idle or
+ * active (dots off = sleeping, dots on = working) for cases where
+ * the number doesn't change for a long(er) period of time.
+ */
+static void db1200_wait(void)
+{
+	__asm__("	.set	push			\n"
+		"	.set	mips3			\n"
+		"	.set	noreorder		\n"
+		"	cache	0x14, 0(%0)		\n"
+		"	cache	0x14, 32(%0)		\n"
+		"	cache	0x14, 64(%0)		\n"
+		/* dots off: we're about to call wait */
+		"	lui	$26, 0xb980		\n"
+		"	ori	$27, $0, 3		\n"
+		"	sb	$27, 0x18($26)		\n"
+		"	sync				\n"
+		"	nop				\n"
+		"	wait				\n"
+		"	nop				\n"
+		"	nop				\n"
+		"	nop				\n"
+		"	nop				\n"
+		"	nop				\n"
+		/* dots on: there's work to do, increment cntr */
+		"	lui	$26, 0xb980		\n"
+		"	sb	$0, 0x18($26)		\n"
+		"	lui	$26, 0xb9c0		\n"
+		"	lb	$27, 0($26)		\n"
+		"	addiu	$27, $27, 1		\n"
+		"	sb	$27, 0($26)		\n"
+		"	sync				\n"
+		"	.set	pop			\n"
+		: : "r" (db1200_wait));
+}
+
+static int __init db1200_arch_init(void)
+{
+	/* GPIO7 is low-level triggered CPLD cascade */
+	set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+	bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
+
+	/* do not autoenable these: CPLD has broken edge int handling,
+	 * and the CD handler setup requires manual enabling to work
+	 * around that.
+	 */
+	irq_to_desc(DB1200_SD0_INSERT_INT)->status |= IRQ_NOAUTOEN;
+	irq_to_desc(DB1200_SD0_EJECT_INT)->status |= IRQ_NOAUTOEN;
+
+	if (cpu_wait)
+		cpu_wait = db1200_wait;
+
+	return 0;
+}
+arch_initcall(db1200_arch_init);
diff --git a/arch/mips/alchemy/devboards/db1x00/Makefile b/arch/mips/alchemy/devboards/db1x00/Makefile
index 432241a..613c0c0 100644
--- a/arch/mips/alchemy/devboards/db1x00/Makefile
+++ b/arch/mips/alchemy/devboards/db1x00/Makefile
@@ -5,4 +5,4 @@
 # Makefile for the Alchemy Semiconductor DBAu1xx0 boards.
 #
 
-obj-y := board_setup.o irqmap.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/db1x00/board_setup.c b/arch/mips/alchemy/devboards/db1x00/board_setup.c
index de30d8e..50c9bef 100644
--- a/arch/mips/alchemy/devboards/db1x00/board_setup.c
+++ b/arch/mips/alchemy/devboards/db1x00/board_setup.c
@@ -29,59 +29,139 @@
 
 #include <linux/gpio.h>
 #include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
 
 #include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-au1x00/au1xxx_eth.h>
 #include <asm/mach-db1x00/db1x00.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/reboot.h>
 
 #include <prom.h>
 
+#ifdef CONFIG_MIPS_DB1500
+char irq_tab_alchemy[][5] __initdata = {
+	[12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - HPT371   */
+	[13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
+};
+
+#endif
 
-static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR;
+
+#ifdef CONFIG_MIPS_DB1550
+char irq_tab_alchemy[][5] __initdata = {
+	[11] = { -1, AU1550_PCI_INTC, 0xff, 0xff, 0xff }, /* IDSEL 11 - on-board HPT371 */
+	[12] = { -1, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD, AU1550_PCI_INTA }, /* IDSEL 12 - PCI slot 2 (left) */
+	[13] = { -1, AU1550_PCI_INTA, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD }, /* IDSEL 13 - PCI slot 1 (right) */
+};
+#endif
+
+
+#ifdef CONFIG_MIPS_BOSPORUS
+char irq_tab_alchemy[][5] __initdata = {
+	[11] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 11 - miniPCI  */
+	[12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff }, /* IDSEL 12 - SN1741   */
+	[13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD }, /* IDSEL 13 - PCI slot */
+};
+
+/*
+ * Micrel/Kendin 5 port switch attached to MAC0,
+ * MAC0 is associated with PHY address 5 (== WAN port)
+ * MAC1 is not associated with any PHY, since it's connected directly
+ * to the switch.
+ * no interrupts are used
+ */
+static struct au1000_eth_platform_data eth0_pdata = {
+	.phy_static_config	= 1,
+	.phy_addr		= 5,
+};
+
+static void bosporus_power_off(void)
+{
+	printk(KERN_INFO "It's now safe to turn off power\n");
+	while (1)
+		asm volatile (".set mips3 ; wait ; .set mips0");
+}
 
 const char *get_system_type(void)
 {
-#ifdef CONFIG_MIPS_BOSPORUS
 	return "Alchemy Bosporus Gateway Reference";
-#else
-	return "Alchemy Db1x00";
+}
 #endif
+
+
+#ifdef CONFIG_MIPS_MIRAGE
+char irq_tab_alchemy[][5] __initdata = {
+	[11] = { -1, AU1500_PCI_INTD, 0xff, 0xff, 0xff }, /* IDSEL 11 - SMI VGX */
+	[12] = { -1, 0xff, 0xff, AU1500_PCI_INTC, 0xff }, /* IDSEL 12 - PNX1300 */
+	[13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 13 - miniPCI */
+};
+
+static void mirage_power_off(void)
+{
+	alchemy_gpio_direction_output(210, 1);
+}
+
+const char *get_system_type(void)
+{
+	return "Alchemy Mirage";
+}
+#endif
+
+
+#if defined(CONFIG_MIPS_BOSPORUS) || defined(CONFIG_MIPS_MIRAGE)
+static void mips_softreset(void)
+{
+	asm volatile ("jr\t%0" : : "r"(0xbfc00000));
 }
 
-void board_reset(void)
+#else
+
+const char *get_system_type(void)
 {
-	/* Hit BCSR.SW_RESET[RESET] */
-	bcsr->swreset = 0x0000;
+	return "Alchemy Db1x00";
 }
+#endif
+
 
 void __init board_setup(void)
 {
-	u32 pin_func = 0;
-	char *argptr;
-
-	argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
+	unsigned long bcsr1, bcsr2;
+	u32 pin_func;
+
+	bcsr1 = DB1000_BCSR_PHYS_ADDR;
+	bcsr2 = DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS;
+
+	pin_func = 0;
+
+#ifdef CONFIG_MIPS_DB1000
+	printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1500
+	printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
 #endif
+#ifdef CONFIG_MIPS_DB1100
+	printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+#endif
+#ifdef CONFIG_MIPS_BOSPORUS
+	au1xxx_override_eth_cfg(0, &eth0_pdata);
 
-#ifdef CONFIG_FB_AU1100
-	argptr = strstr(argptr, "video=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		/* default panel */
-		/*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
-	}
+	printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
 #endif
+#ifdef CONFIG_MIPS_MIRAGE
+	printk(KERN_INFO "AMD Alchemy Mirage Board\n");
+#endif
+#ifdef CONFIG_MIPS_DB1550
+	printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
 
-#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
-	/* au1000 does not support vra, au1500 and au1100 do */
-	strcat(argptr, " au1000_audio=vra");
-	argptr = prom_getcmdline();
+	bcsr1 = DB1550_BCSR_PHYS_ADDR;
+	bcsr2 = DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS;
 #endif
 
+	/* initialize board register space */
+	bcsr_init(bcsr1, bcsr2);
+
 	/* Not valid for Au1550 */
 #if defined(CONFIG_IRDA) && \
    (defined(CONFIG_SOC_AU1000) || defined(CONFIG_SOC_AU1100))
@@ -89,11 +169,10 @@ void __init board_setup(void)
 	pin_func = au_readl(SYS_PINFUNC) | SYS_PF_IRF;
 	au_writel(pin_func, SYS_PINFUNC);
 	/* Power off until the driver is in use */
-	bcsr->resets &= ~BCSR_RESETS_IRDA_MODE_MASK;
-	bcsr->resets |=  BCSR_RESETS_IRDA_MODE_OFF;
-	au_sync();
+	bcsr_mod(BCSR_RESETS, BCSR_RESETS_IRDA_MODE_MASK,
+				BCSR_RESETS_IRDA_MODE_OFF);
 #endif
-	bcsr->pcmcia = 0x0000; /* turn off PCMCIA power */
+	bcsr_write(BCSR_PCMCIA, 0);	/* turn off PCMCIA power */
 
 	/* Enable GPIO[31:0] inputs */
 	alchemy_gpio1_input_enable();
@@ -120,26 +199,53 @@ void __init board_setup(void)
 	 * be part of the audio driver.
 	 */
 	alchemy_gpio_direction_output(209, 1);
-#endif
-
-	au_sync();
 
-#ifdef CONFIG_MIPS_DB1000
-	printk(KERN_INFO "AMD Alchemy Au1000/Db1000 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1500
-	printk(KERN_INFO "AMD Alchemy Au1500/Db1500 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1100
-	printk(KERN_INFO "AMD Alchemy Au1100/Db1100 Board\n");
+	pm_power_off = mirage_power_off;
+	_machine_halt = mirage_power_off;
+	_machine_restart = (void(*)(char *))mips_softreset;
 #endif
+
 #ifdef CONFIG_MIPS_BOSPORUS
-	printk(KERN_INFO "AMD Alchemy Bosporus Board\n");
+	pm_power_off = bosporus_power_off;
+	_machine_halt = bosporus_power_off;
+	_machine_restart = (void(*)(char *))mips_softreset;
 #endif
-#ifdef CONFIG_MIPS_MIRAGE
-	printk(KERN_INFO "AMD Alchemy Mirage Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1550
-	printk(KERN_INFO "AMD Alchemy Au1550/Db1550 Board\n");
+	au_sync();
+}
+
+static int __init db1x00_init_irq(void)
+{
+#if defined(CONFIG_MIPS_MIRAGE)
+	set_irq_type(AU1500_GPIO7_INT, IRQF_TRIGGER_RISING); /* TS pendown */
+#elif defined(CONFIG_MIPS_DB1550)
+	set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);  /* CD0# */
+	set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);  /* CD1# */
+	set_irq_type(AU1550_GPIO3_INT, IRQF_TRIGGER_LOW);  /* CARD0# */
+	set_irq_type(AU1550_GPIO5_INT, IRQF_TRIGGER_LOW);  /* CARD1# */
+	set_irq_type(AU1550_GPIO21_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+	set_irq_type(AU1550_GPIO22_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
+#elif defined(CONFIG_MIPS_DB1500)
+	set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
+	set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
+	set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
+	set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
+	set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+	set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
+#elif defined(CONFIG_MIPS_DB1100)
+	set_irq_type(AU1100_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
+	set_irq_type(AU1100_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
+	set_irq_type(AU1100_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
+	set_irq_type(AU1100_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
+	set_irq_type(AU1100_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+	set_irq_type(AU1100_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
+#elif defined(CONFIG_MIPS_DB1000)
+	set_irq_type(AU1000_GPIO0_INT, IRQF_TRIGGER_LOW); /* CD0# */
+	set_irq_type(AU1000_GPIO3_INT, IRQF_TRIGGER_LOW); /* CD1# */
+	set_irq_type(AU1000_GPIO2_INT, IRQF_TRIGGER_LOW); /* CARD0# */
+	set_irq_type(AU1000_GPIO5_INT, IRQF_TRIGGER_LOW); /* CARD1# */
+	set_irq_type(AU1000_GPIO1_INT, IRQF_TRIGGER_LOW); /* STSCHG0# */
+	set_irq_type(AU1000_GPIO4_INT, IRQF_TRIGGER_LOW); /* STSCHG1# */
 #endif
+	return 0;
 }
+arch_initcall(db1x00_init_irq);
diff --git a/arch/mips/alchemy/devboards/db1x00/irqmap.c b/arch/mips/alchemy/devboards/db1x00/irqmap.c
deleted file mode 100644
index 0b09025..0000000
--- a/arch/mips/alchemy/devboards/db1x00/irqmap.c
+++ /dev/null
@@ -1,90 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- *	Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- *		dan@embeddededge.com
- *
- *  This program is free software; you can redistribute	 it and/or modify it
- *  under  the terms of	 the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the	License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
- *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
- *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_MIPS_DB1500
-char irq_tab_alchemy[][5] __initdata = {
-	[12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - HPT371   */
-	[13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_BOSPORUS
-char irq_tab_alchemy[][5] __initdata = {
-	[11] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 11 - miniPCI  */
-	[12] = { -1, INTA, INTX, INTX, INTX }, /* IDSEL 12 - SN1741   */
-	[13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot */
-};
-#endif
-
-#ifdef CONFIG_MIPS_MIRAGE
-char irq_tab_alchemy[][5] __initdata = {
-	[11] = { -1, INTD, INTX, INTX, INTX }, /* IDSEL 11 - SMI VGX */
-	[12] = { -1, INTX, INTX, INTC, INTX }, /* IDSEL 12 - PNX1300 */
-	[13] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 13 - miniPCI */
-};
-#endif
-
-#ifdef CONFIG_MIPS_DB1550
-char irq_tab_alchemy[][5] __initdata = {
-	[11] = { -1, INTC, INTX, INTX, INTX }, /* IDSEL 11 - on-board HPT371 */
-	[12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left) */
-	[13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-#endif
-
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-
-#ifndef CONFIG_MIPS_MIRAGE
-#ifdef CONFIG_MIPS_DB1550
-	{ AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 IRQ# */
-	{ AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 IRQ# */
-#else
-	{ AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 Fully_Interted# */
-	{ AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 STSCHG# */
-	{ AU1000_GPIO_2, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 0 IRQ# */
-
-	{ AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 Fully_Interted# */
-	{ AU1000_GPIO_4, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 STSCHG# */
-	{ AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card 1 IRQ# */
-#endif
-#else
-	{ AU1000_GPIO_7, IRQF_TRIGGER_RISING, 0 }, /* touchscreen pen down */
-#endif
-
-};
-
-void __init board_init_irq(void)
-{
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
diff --git a/arch/mips/alchemy/devboards/db1x00/platform.c b/arch/mips/alchemy/devboards/db1x00/platform.c
new file mode 100644
index 0000000..978d5ab
--- /dev/null
+++ b/arch/mips/alchemy/devboards/db1x00/platform.c
@@ -0,0 +1,118 @@
+/*
+ * DBAu1xxx board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-au1x00/au1xxx.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include "../platform.h"
+
+/* DB1xxx PCMCIA interrupt sources:
+ * CD0/1 	GPIO0/3
+ * STSCHG0/1	GPIO1/4
+ * CARD0/1	GPIO2/5
+ * Db1550:	0/1, 21/22, 3/5
+ */
+
+#define DB1XXX_HAS_PCMCIA
+#define F_SWAPPED (bcsr_read(BCSR_STATUS) & BCSR_STATUS_DB1000_SWAPBOOT)
+
+#if defined(CONFIG_MIPS_DB1000)
+#define DB1XXX_PCMCIA_CD0	AU1000_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0	AU1000_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0	AU1000_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1	AU1000_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1	AU1000_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1	AU1000_GPIO5_INT
+#define BOARD_FLASH_SIZE	0x02000000 /* 32MB */
+#define BOARD_FLASH_WIDTH	4 /* 32-bits */
+#elif defined(CONFIG_MIPS_DB1100)
+#define DB1XXX_PCMCIA_CD0	AU1100_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0	AU1100_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0	AU1100_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1	AU1100_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1	AU1100_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1	AU1100_GPIO5_INT
+#define BOARD_FLASH_SIZE	0x02000000 /* 32MB */
+#define BOARD_FLASH_WIDTH	4 /* 32-bits */
+#elif defined(CONFIG_MIPS_DB1500)
+#define DB1XXX_PCMCIA_CD0	AU1500_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0	AU1500_GPIO1_INT
+#define DB1XXX_PCMCIA_CARD0	AU1500_GPIO2_INT
+#define DB1XXX_PCMCIA_CD1	AU1500_GPIO3_INT
+#define DB1XXX_PCMCIA_STSCHG1	AU1500_GPIO4_INT
+#define DB1XXX_PCMCIA_CARD1	AU1500_GPIO5_INT
+#define BOARD_FLASH_SIZE	0x02000000 /* 32MB */
+#define BOARD_FLASH_WIDTH	4 /* 32-bits */
+#elif defined(CONFIG_MIPS_DB1550)
+#define DB1XXX_PCMCIA_CD0	AU1550_GPIO0_INT
+#define DB1XXX_PCMCIA_STSCHG0	AU1550_GPIO21_INT
+#define DB1XXX_PCMCIA_CARD0	AU1550_GPIO3_INT
+#define DB1XXX_PCMCIA_CD1	AU1550_GPIO1_INT
+#define DB1XXX_PCMCIA_STSCHG1	AU1550_GPIO22_INT
+#define DB1XXX_PCMCIA_CARD1	AU1550_GPIO5_INT
+#define BOARD_FLASH_SIZE	0x08000000 /* 128MB */
+#define BOARD_FLASH_WIDTH	4 /* 32-bits */
+#else
+/* other board: no PCMCIA */
+#undef DB1XXX_HAS_PCMCIA
+#undef F_SWAPPED
+#define F_SWAPPED 0
+#if defined(CONFIG_MIPS_BOSPORUS)
+#define BOARD_FLASH_SIZE	0x01000000 /* 16MB */
+#define BOARD_FLASH_WIDTH	2 /* 16-bits */
+#elif defined(CONFIG_MIPS_MIRAGE)
+#define BOARD_FLASH_SIZE	0x04000000 /* 64MB */
+#define BOARD_FLASH_WIDTH	4 /* 32-bits */
+#endif
+#endif
+
+static int __init db1xxx_dev_init(void)
+{
+#ifdef DB1XXX_HAS_PCMCIA
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR,
+				    PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+				    DB1XXX_PCMCIA_CARD0,
+				    DB1XXX_PCMCIA_CD0,
+				    /*DB1XXX_PCMCIA_STSCHG0*/0,
+				    0,
+				    0);
+
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR   + 0x004000000,
+				    PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
+				    DB1XXX_PCMCIA_CARD1,
+				    DB1XXX_PCMCIA_CD1,
+				    /*DB1XXX_PCMCIA_STSCHG1*/0,
+				    0,
+				    1);
+#endif
+	db1x_register_norflash(BOARD_FLASH_SIZE, BOARD_FLASH_WIDTH, F_SWAPPED);
+	return 0;
+}
+device_initcall(db1xxx_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1000/board_setup.c b/arch/mips/alchemy/devboards/pb1000/board_setup.c
index cd273545..b5311d8 100644
--- a/arch/mips/alchemy/devboards/pb1000/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1000/board_setup.c
@@ -31,11 +31,7 @@
 #include <asm/mach-pb1x00/pb1000.h>
 #include <prom.h>
 
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-	{ AU1000_GPIO_15, IRQF_TRIGGER_LOW, 0 },
-};
-
+#include "../platform.h"
 
 const char *get_system_type(void)
 {
@@ -46,25 +42,14 @@ void board_reset(void)
 {
 }
 
-void __init board_init_irq(void)
-{
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
-
 void __init board_setup(void)
 {
 	u32 pin_func, static_cfg0;
 	u32 sys_freqctrl, sys_clksrc;
 	u32 prid = read_c0_prid();
 
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	char *argptr = prom_getcmdline();
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
-#endif
+	sys_freqctrl = 0;
+	sys_clksrc = 0;
 
 	/* Set AUX clock to 12 MHz * 8 = 96 MHz */
 	au_writel(8, SYS_AUXPLL);
@@ -193,3 +178,16 @@ void __init board_setup(void)
 		break;
 	}
 }
+
+static int __init pb1000_init_irq(void)
+{
+	set_irq_type(AU1000_GPIO15_INT, IRQF_TRIGGER_LOW);
+	return 0;
+}
+arch_initcall(pb1000_init_irq);
+
+static int __init pb1000_device_init(void)
+{
+	return db1x_register_norflash(8 * 1024 * 1024, 4, 0);
+}
+device_initcall(pb1000_device_init);
diff --git a/arch/mips/alchemy/devboards/pb1100/Makefile b/arch/mips/alchemy/devboards/pb1100/Makefile
index c586dd7..7e3756c 100644
--- a/arch/mips/alchemy/devboards/pb1100/Makefile
+++ b/arch/mips/alchemy/devboards/pb1100/Makefile
@@ -5,4 +5,4 @@
 # Makefile for the Alchemy Semiconductor Pb1100 board.
 #
 
-obj-y := board_setup.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1100/board_setup.c b/arch/mips/alchemy/devboards/pb1100/board_setup.c
index 6126308..c7b4caa 100644
--- a/arch/mips/alchemy/devboards/pb1100/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1100/board_setup.c
@@ -29,19 +29,11 @@
 #include <linux/interrupt.h>
 
 #include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1100.h>
+#include <asm/mach-db1x00/bcsr.h>
 
 #include <prom.h>
 
 
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-	{ AU1000_GPIO_9,  IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card Fully_Inserted# */
-	{ AU1000_GPIO_10, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card STSCHG# */
-	{ AU1000_GPIO_11, IRQF_TRIGGER_LOW, 0 }, /* PCMCIA Card IRQ# */
-	{ AU1000_GPIO_13, IRQF_TRIGGER_LOW, 0 }, /* DC_IRQ# */
-};
-
-
 const char *get_system_type(void)
 {
 	return "Alchemy Pb1100";
@@ -49,43 +41,15 @@ const char *get_system_type(void)
 
 void board_reset(void)
 {
-	/* Hit BCSR.RST_VDDI[SOFT_RESET] */
-	au_writel(0x00000000, PB1100_RST_VDDI);
-}
-
-void __init board_init_irq(void)
-{
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
+	bcsr_write(BCSR_SYSTEM, 0);
 }
 
 void __init board_setup(void)
 {
 	volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
-	char *argptr;
-
-	argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
-#endif
-
-#ifdef CONFIG_FB_AU1100
-	argptr = strstr(argptr, "video=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		/* default panel */
-		/*strcat(argptr, " video=au1100fb:panel:Sharp_320x240_16");*/
-	}
-#endif
 
-#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
-	/* au1000 does not support vra, au1500 and au1100 do */
-	strcat(argptr, " au1000_audio=vra");
-	argptr = prom_getcmdline();
-#endif
+	bcsr_init(DB1000_BCSR_PHYS_ADDR,
+		  DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
 
 	/* Set AUX clock to 12 MHz * 8 = 96 MHz */
 	au_writel(8, SYS_AUXPLL);
@@ -155,3 +119,14 @@ void __init board_setup(void)
 		au_sync();
 	}
 }
+
+static int __init pb1100_init_irq(void)
+{
+	set_irq_type(AU1100_GPIO9_INT,  IRQF_TRIGGER_LOW); /* PCCD# */
+	set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
+	set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
+	set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
+
+	return 0;
+}
+arch_initcall(pb1100_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1100/platform.c b/arch/mips/alchemy/devboards/pb1100/platform.c
new file mode 100644
index 0000000..2c8dc29
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1100/platform.c
@@ -0,0 +1,50 @@
+/*
+ * Pb1100 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/init.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
+
+static int __init pb1100_dev_init(void)
+{
+	int swapped;
+
+	/* PCMCIA. single socket, identical to Pb1500 */
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR,
+				    PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+				    AU1100_GPIO11_INT,	 /* card */
+				    AU1100_GPIO9_INT,	 /* insert */
+				    /*AU1100_GPIO10_INT*/0, /* stschg */
+				    0,			 /* eject */
+				    0);			 /* id */
+
+	swapped = bcsr_read(BCSR_STATUS) &  BCSR_STATUS_DB1000_SWAPBOOT;
+	db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+
+	return 0;
+}
+device_initcall(pb1100_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1200/Makefile b/arch/mips/alchemy/devboards/pb1200/Makefile
index c8c3a99..2ea9b02 100644
--- a/arch/mips/alchemy/devboards/pb1200/Makefile
+++ b/arch/mips/alchemy/devboards/pb1200/Makefile
@@ -2,6 +2,6 @@
 # Makefile for the Alchemy Semiconductor Pb1200/DBAu1200 boards.
 #
 
-obj-y := board_setup.o irqmap.o platform.o
+obj-y := board_setup.o platform.o
 
 EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/devboards/pb1200/board_setup.c b/arch/mips/alchemy/devboards/pb1200/board_setup.c
index 94e6b7e..3184063 100644
--- a/arch/mips/alchemy/devboards/pb1200/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1200/board_setup.c
@@ -25,11 +25,23 @@
  */
 
 #include <linux/init.h>
+#include <linux/interrupt.h>
 #include <linux/sched.h>
 
-#include <prom.h>
-#include <au1xxx.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#ifdef CONFIG_MIPS_PB1200
+#include <asm/mach-pb1x00/pb1200.h>
+#endif
+
+#ifdef CONFIG_MIPS_DB1200
+#include <asm/mach-db1x00/db1200.h>
+#define PB1200_INT_BEGIN DB1200_INT_BEGIN
+#define PB1200_INT_END DB1200_INT_END
+#endif
 
+#include <prom.h>
 
 const char *get_system_type(void)
 {
@@ -38,25 +50,15 @@ const char *get_system_type(void)
 
 void board_reset(void)
 {
-	bcsr->resets = 0;
-	bcsr->system = 0;
+	bcsr_write(BCSR_RESETS, 0);
+	bcsr_write(BCSR_SYSTEM, 0);
 }
 
 void __init board_setup(void)
 {
-	char *argptr;
-
-	argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
-#endif
-#ifdef CONFIG_FB_AU1200
-	strcat(argptr, " video=au1200fb:panel:bs");
-#endif
+	printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
+	bcsr_init(PB1200_BCSR_PHYS_ADDR,
+		  PB1200_BCSR_PHYS_ADDR + PB1200_BCSR_HEXLED_OFS);
 
 #if 0
 	{
@@ -82,7 +84,7 @@ void __init board_setup(void)
 		u32 pin_func;
 
 		/* Select SMBus in CPLD */
-		bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+		bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
 
 		pin_func = au_readl(SYS_PINFUNC);
 		au_sync();
@@ -116,38 +118,54 @@ void __init board_setup(void)
 
 	/*
 	 * The Pb1200 development board uses external MUX for PSC0 to
-	 * support SMB/SPI. bcsr->resets bit 12: 0=SMB 1=SPI
+	 * support SMB/SPI. bcsr_resets bit 12: 0=SMB 1=SPI
 	 */
 #ifdef CONFIG_I2C_AU1550
-	bcsr->resets &= ~BCSR_RESETS_PCS0MUX;
+	bcsr_mod(BCSR_RESETS, BCSR_RESETS_PSC0MUX, 0);
 #endif
 	au_sync();
+}
 
-#ifdef CONFIG_MIPS_PB1200
-	printk(KERN_INFO "AMD Alchemy Pb1200 Board\n");
-#endif
-#ifdef CONFIG_MIPS_DB1200
-	printk(KERN_INFO "AMD Alchemy Db1200 Board\n");
-#endif
+static int __init pb1200_init_irq(void)
+{
+	/* We have a problem with CPLD rev 3. */
+	if (BCSR_WHOAMI_CPLD(bcsr_read(BCSR_WHOAMI)) <= 3) {
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
+		printk(KERN_ERR "updated to latest revision. This software will\n");
+		printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		printk(KERN_ERR "WARNING!!!\n");
+		panic("Game over.  Your score is 0.");
+	}
+
+	set_irq_type(AU1200_GPIO7_INT, IRQF_TRIGGER_LOW);
+	bcsr_init_irq(PB1200_INT_BEGIN, PB1200_INT_END, AU1200_GPIO7_INT);
+
+	return 0;
 }
+arch_initcall(pb1200_init_irq);
+
 
 int board_au1200fb_panel(void)
 {
-	BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-	int p;
-
-	p = bcsr->switches;
-	p >>= 8;
-	p &= 0x0F;
-	return p;
+	return (bcsr_read(BCSR_SWITCHES) >> 8) & 0x0f;
 }
 
 int board_au1200fb_panel_init(void)
 {
 	/* Apply power */
-	BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-
-	bcsr->board |= BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD | BCSR_BOARD_LCDBL;
+	bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+				BCSR_BOARD_LCDBL);
 	/* printk(KERN_DEBUG "board_au1200fb_panel_init()\n"); */
 	return 0;
 }
@@ -155,10 +173,8 @@ int board_au1200fb_panel_init(void)
 int board_au1200fb_panel_shutdown(void)
 {
 	/* Remove power */
-	BCSR *bcsr = (BCSR *)BCSR_KSEG1_ADDR;
-
-	bcsr->board &= ~(BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
-			 BCSR_BOARD_LCDBL);
+	bcsr_mod(BCSR_BOARD, BCSR_BOARD_LCDVEE | BCSR_BOARD_LCDVDD |
+			     BCSR_BOARD_LCDBL, 0);
 	/* printk(KERN_DEBUG "board_au1200fb_panel_shutdown()\n"); */
 	return 0;
 }
diff --git a/arch/mips/alchemy/devboards/pb1200/irqmap.c b/arch/mips/alchemy/devboards/pb1200/irqmap.c
deleted file mode 100644
index fe47498..0000000
--- a/arch/mips/alchemy/devboards/pb1200/irqmap.c
+++ /dev/null
@@ -1,134 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- *	Au1xxx irq map table
- *
- *  This program is free software; you can redistribute	 it and/or modify it
- *  under  the terms of	 the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the	License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
- *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
- *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_MIPS_PB1200
-#include <asm/mach-pb1x00/pb1200.h>
-#endif
-
-#ifdef CONFIG_MIPS_DB1200
-#include <asm/mach-db1x00/db1200.h>
-#define PB1200_INT_BEGIN DB1200_INT_BEGIN
-#define PB1200_INT_END DB1200_INT_END
-#endif
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-	/* This is external interrupt cascade */
-	{ AU1000_GPIO_7, IRQF_TRIGGER_LOW, 0 },
-};
-
-
-/*
- * Support for External interrupts on the Pb1200 Development platform.
- */
-
-static void pb1200_cascade_handler(unsigned int irq, struct irq_desc *d)
-{
-	unsigned short bisr = bcsr->int_status;
-
-	for ( ; bisr; bisr &= bisr - 1)
-		generic_handle_irq(PB1200_INT_BEGIN + __ffs(bisr));
-}
-
-/* NOTE: both the enable and mask bits must be cleared, otherwise the
- * CPLD generates tons of spurious interrupts (at least on the DB1200).
- */
-static void pb1200_mask_irq(unsigned int irq_nr)
-{
-	bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
-	bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
-	au_sync();
-}
-
-static void pb1200_maskack_irq(unsigned int irq_nr)
-{
-	bcsr->intclr_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
-	bcsr->intclr = 1 << (irq_nr - PB1200_INT_BEGIN);
-	bcsr->int_status = 1 << (irq_nr - PB1200_INT_BEGIN);	/* ack */
-	au_sync();
-}
-
-static void pb1200_unmask_irq(unsigned int irq_nr)
-{
-	bcsr->intset = 1 << (irq_nr - PB1200_INT_BEGIN);
-	bcsr->intset_mask = 1 << (irq_nr - PB1200_INT_BEGIN);
-	au_sync();
-}
-
-static struct irq_chip pb1200_cpld_irq_type = {
-#ifdef CONFIG_MIPS_PB1200
-	.name = "Pb1200 Ext",
-#endif
-#ifdef CONFIG_MIPS_DB1200
-	.name = "Db1200 Ext",
-#endif
-	.mask		= pb1200_mask_irq,
-	.mask_ack	= pb1200_maskack_irq,
-	.unmask		= pb1200_unmask_irq,
-};
-
-void __init board_init_irq(void)
-{
-	unsigned int irq;
-
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-
-#ifdef CONFIG_MIPS_PB1200
-	/* We have a problem with CPLD rev 3. */
-	if (((bcsr->whoami & BCSR_WHOAMI_CPLD) >> 4) <= 3) {
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "Pb1200 must be at CPLD rev 4. Please have Pb1200\n");
-		printk(KERN_ERR "updated to latest revision. This software will\n");
-		printk(KERN_ERR "not work on anything less than CPLD rev 4.\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		printk(KERN_ERR "WARNING!!!\n");
-		panic("Game over.  Your score is 0.");
-	}
-#endif
-	/* mask & disable & ack all */
-	bcsr->intclr_mask = 0xffff;
-	bcsr->intclr = 0xffff;
-	bcsr->int_status = 0xffff;
-	au_sync();
-
-	for (irq = PB1200_INT_BEGIN; irq <= PB1200_INT_END; irq++)
-		set_irq_chip_and_handler_name(irq, &pb1200_cpld_irq_type,
-					 handle_level_irq, "level");
-
-	set_irq_chained_handler(AU1000_GPIO_7, pb1200_cascade_handler);
-}
diff --git a/arch/mips/alchemy/devboards/pb1200/platform.c b/arch/mips/alchemy/devboards/pb1200/platform.c
index b93dff4..3ef2dce 100644
--- a/arch/mips/alchemy/devboards/pb1200/platform.c
+++ b/arch/mips/alchemy/devboards/pb1200/platform.c
@@ -26,27 +26,30 @@
 
 #include <asm/mach-au1x00/au1xxx.h>
 #include <asm/mach-au1x00/au1100_mmc.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
 
 static int mmc_activity;
 
 static void pb1200mmc0_set_power(void *mmc_host, int state)
 {
 	if (state)
-		bcsr->board |= BCSR_BOARD_SD0PWR;
+		bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD0PWR);
 	else
-		bcsr->board &= ~BCSR_BOARD_SD0PWR;
+		bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD0PWR, 0);
 
-	au_sync_delay(1);
+	msleep(1);
 }
 
 static int pb1200mmc0_card_readonly(void *mmc_host)
 {
-	return (bcsr->status & BCSR_STATUS_SD0WP) ? 1 : 0;
+	return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD0WP) ? 1 : 0;
 }
 
 static int pb1200mmc0_card_inserted(void *mmc_host)
 {
-	return (bcsr->sig_status & BCSR_INT_SD0INSERT) ? 1 : 0;
+	return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD0INSERT) ? 1 : 0;
 }
 
 static void pb1200_mmcled_set(struct led_classdev *led,
@@ -54,10 +57,10 @@ static void pb1200_mmcled_set(struct led_classdev *led,
 {
 	if (brightness != LED_OFF) {
 		if (++mmc_activity == 1)
-			bcsr->disk_leds &= ~(1 << 8);
+			bcsr_mod(BCSR_LEDS, BCSR_LEDS_LED0, 0);
 	} else {
 		if (--mmc_activity == 0)
-			bcsr->disk_leds |= (1 << 8);
+			bcsr_mod(BCSR_LEDS, 0, BCSR_LEDS_LED0);
 	}
 }
 
@@ -65,27 +68,25 @@ static struct led_classdev pb1200mmc_led = {
 	.brightness_set	= pb1200_mmcled_set,
 };
 
-#ifndef CONFIG_MIPS_DB1200
 static void pb1200mmc1_set_power(void *mmc_host, int state)
 {
 	if (state)
-		bcsr->board |= BCSR_BOARD_SD1PWR;
+		bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SD1PWR);
 	else
-		bcsr->board &= ~BCSR_BOARD_SD1PWR;
+		bcsr_mod(BCSR_BOARD, BCSR_BOARD_SD1PWR, 0);
 
-	au_sync_delay(1);
+	msleep(1);
 }
 
 static int pb1200mmc1_card_readonly(void *mmc_host)
 {
-	return (bcsr->status & BCSR_STATUS_SD1WP) ? 1 : 0;
+	return (bcsr_read(BCSR_STATUS) & BCSR_STATUS_SD1WP) ? 1 : 0;
 }
 
 static int pb1200mmc1_card_inserted(void *mmc_host)
 {
-	return (bcsr->sig_status & BCSR_INT_SD1INSERT) ? 1 : 0;
+	return (bcsr_read(BCSR_SIGSTAT) & BCSR_INT_SD1INSERT) ? 1 : 0;
 }
-#endif
 
 const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
 	[0] = {
@@ -95,7 +96,6 @@ const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
 		.cd_setup	= NULL,		/* use poll-timer in driver */
 		.led		= &pb1200mmc_led,
 	},
-#ifndef CONFIG_MIPS_DB1200
 	[1] = {
 		.set_power	= pb1200mmc1_set_power,
 		.card_inserted	= pb1200mmc1_card_inserted,
@@ -103,7 +103,6 @@ const struct au1xmmc_platform_data au1xmmc_platdata[2] = {
 		.cd_setup	= NULL,		/* use poll-timer in driver */
 		.led		= &pb1200mmc_led,
 	},
-#endif
 };
 
 static struct resource ide_resources[] = {
@@ -169,8 +168,36 @@ static struct platform_device *board_platform_devices[] __initdata = {
 
 static int __init board_register_devices(void)
 {
+	int swapped;
+
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR,
+				    PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+				    PB1200_PC0_INT,
+				    PB1200_PC0_INSERT_INT,
+				    /*PB1200_PC0_STSCHG_INT*/0,
+				    PB1200_PC0_EJECT_INT,
+				    0);
+
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x008000000,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x008400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR   + 0x008000000,
+				    PCMCIA_IO_PHYS_ADDR   + 0x008010000 - 1,
+				    PB1200_PC1_INT,
+				    PB1200_PC1_INSERT_INT,
+				    /*PB1200_PC1_STSCHG_INT*/0,
+				    PB1200_PC1_EJECT_INT,
+				    1);
+
+	swapped = bcsr_read(BCSR_STATUS) &  BCSR_STATUS_DB1200_SWAPBOOT;
+	db1x_register_norflash(128 * 1024 * 1024, 2, swapped);
+
 	return platform_add_devices(board_platform_devices,
 				    ARRAY_SIZE(board_platform_devices));
 }
-
-arch_initcall(board_register_devices);
+device_initcall(board_register_devices);
diff --git a/arch/mips/alchemy/devboards/pb1500/Makefile b/arch/mips/alchemy/devboards/pb1500/Makefile
index 173b419..e83b151 100644
--- a/arch/mips/alchemy/devboards/pb1500/Makefile
+++ b/arch/mips/alchemy/devboards/pb1500/Makefile
@@ -5,4 +5,4 @@
 # Makefile for the Alchemy Semiconductor Pb1500 board.
 #
 
-obj-y := board_setup.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1500/board_setup.c b/arch/mips/alchemy/devboards/pb1500/board_setup.c
index d7a5656..fa9770a 100644
--- a/arch/mips/alchemy/devboards/pb1500/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1500/board_setup.c
@@ -29,22 +29,14 @@
 #include <linux/interrupt.h>
 
 #include <asm/mach-au1x00/au1000.h>
-#include <asm/mach-pb1x00/pb1500.h>
+#include <asm/mach-db1x00/bcsr.h>
 
 #include <prom.h>
 
 
 char irq_tab_alchemy[][5] __initdata = {
-	[12] = { -1, INTA, INTX, INTX, INTX },   /* IDSEL 12 - HPT370	*/
-	[13] = { -1, INTA, INTB, INTC, INTD },   /* IDSEL 13 - PCI slot */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-	{ AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
-	{ AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
-	{ AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
-	{ AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
-	{ AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
+	[12] = { -1, AU1500_PCI_INTA, 0xff, 0xff, 0xff },   /* IDSEL 12 - HPT370	*/
+	[13] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, AU1500_PCI_INTC, AU1500_PCI_INTD },   /* IDSEL 13 - PCI slot */
 };
 
 
@@ -55,35 +47,16 @@ const char *get_system_type(void)
 
 void board_reset(void)
 {
-	/* Hit BCSR.RST_VDDI[SOFT_RESET] */
-	au_writel(0x00000000, PB1500_RST_VDDI);
-}
-
-void __init board_init_irq(void)
-{
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
+	bcsr_write(BCSR_SYSTEM, 0);
 }
 
 void __init board_setup(void)
 {
 	u32 pin_func;
 	u32 sys_freqctrl, sys_clksrc;
-	char *argptr;
-
-	argptr = prom_getcmdline();
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
-#endif
 
-#if defined(CONFIG_SOUND_AU1X00) && !defined(CONFIG_SOC_AU1000)
-	/* au1000 does not support vra, au1500 and au1100 do */
-	strcat(argptr, " au1000_audio=vra");
-	argptr = prom_getcmdline();
-#endif
+	bcsr_init(DB1000_BCSR_PHYS_ADDR,
+		  DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
 
 	sys_clksrc = sys_freqctrl = pin_func = 0;
 	/* Set AUX clock to 12 MHz * 8 = 96 MHz */
@@ -163,3 +136,18 @@ void __init board_setup(void)
 		au_sync();
 	}
 }
+
+static int __init pb1500_init_irq(void)
+{
+	set_irq_type(AU1500_GPIO9_INT, IRQF_TRIGGER_LOW);   /* CD0# */
+	set_irq_type(AU1500_GPIO10_INT, IRQF_TRIGGER_LOW);  /* CARD0 */
+	set_irq_type(AU1500_GPIO11_INT, IRQF_TRIGGER_LOW);  /* STSCHG0# */
+	set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+	set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+	return 0;
+}
+arch_initcall(pb1500_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1500/platform.c b/arch/mips/alchemy/devboards/pb1500/platform.c
new file mode 100644
index 0000000..d443bc7
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1500/platform.c
@@ -0,0 +1,49 @@
+/*
+ * Pb1500 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/init.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
+
+static int __init pb1500_dev_init(void)
+{
+	int swapped;
+
+	/* PCMCIA. single socket, identical to Pb1500 */
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR,
+				    PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+				    AU1500_GPIO11_INT,	 /* card */
+				    AU1500_GPIO9_INT,	 /* insert */
+				    /*AU1500_GPIO10_INT*/0, /* stschg */
+				    0,			 /* eject */
+				    0);			 /* id */
+
+	swapped = bcsr_read(BCSR_STATUS) &  BCSR_STATUS_DB1000_SWAPBOOT;
+	db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+
+	return 0;
+}
+device_initcall(pb1500_dev_init);
diff --git a/arch/mips/alchemy/devboards/pb1550/Makefile b/arch/mips/alchemy/devboards/pb1550/Makefile
index cff95bc..9661b6e 100644
--- a/arch/mips/alchemy/devboards/pb1550/Makefile
+++ b/arch/mips/alchemy/devboards/pb1550/Makefile
@@ -5,4 +5,4 @@
 # Makefile for the Alchemy Semiconductor Pb1550 board.
 #
 
-obj-y := board_setup.o
+obj-y := board_setup.o platform.o
diff --git a/arch/mips/alchemy/devboards/pb1550/board_setup.c b/arch/mips/alchemy/devboards/pb1550/board_setup.c
index b6e9e7d..1e8fb3d 100644
--- a/arch/mips/alchemy/devboards/pb1550/board_setup.c
+++ b/arch/mips/alchemy/devboards/pb1550/board_setup.c
@@ -32,18 +32,15 @@
 
 #include <asm/mach-au1x00/au1000.h>
 #include <asm/mach-pb1x00/pb1550.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <asm/mach-au1x00/gpio.h>
 
 #include <prom.h>
 
 
 char irq_tab_alchemy[][5] __initdata = {
-	[12] = { -1, INTB, INTC, INTD, INTA }, /* IDSEL 12 - PCI slot 2 (left)  */
-	[13] = { -1, INTA, INTB, INTC, INTD }, /* IDSEL 13 - PCI slot 1 (right) */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-	{ AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 },
-	{ AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 },
+	[12] = { -1, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD, AU1550_PCI_INTA }, /* IDSEL 12 - PCI slot 2 (left)  */
+	[13] = { -1, AU1550_PCI_INTA, AU1550_PCI_INTB, AU1550_PCI_INTC, AU1550_PCI_INTD }, /* IDSEL 13 - PCI slot 1 (right) */
 };
 
 const char *get_system_type(void)
@@ -53,28 +50,17 @@ const char *get_system_type(void)
 
 void board_reset(void)
 {
-	/* Hit BCSR.SYSTEM[RESET] */
-	au_writew(au_readw(0xAF00001C) & ~BCSR_SYSTEM_RESET, 0xAF00001C);
-}
-
-void __init board_init_irq(void)
-{
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
+	bcsr_write(BCSR_SYSTEM, 0);
 }
 
 void __init board_setup(void)
 {
 	u32 pin_func;
 
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	char *argptr;
-	argptr = prom_getcmdline();
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
-#endif
+	bcsr_init(PB1550_BCSR_PHYS_ADDR,
+		  PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
+
+	alchemy_gpio2_enable();
 
 	/*
 	 * Enable PSC1 SYNC for AC'97.  Normaly done in audio driver,
@@ -85,8 +71,21 @@ void __init board_setup(void)
 	pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1;
 	au_writel(pin_func, SYS_PINFUNC);
 
-	au_writel(0, (u32)bcsr | 0x10); /* turn off PCMCIA power */
-	au_sync();
+	bcsr_write(BCSR_PCMCIA, 0);	/* turn off PCMCIA power */
 
 	printk(KERN_INFO "AMD Alchemy Pb1550 Board\n");
 }
+
+static int __init pb1550_init_irq(void)
+{
+	set_irq_type(AU1550_GPIO0_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1550_GPIO1_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1550_GPIO201_205_INT, IRQF_TRIGGER_HIGH);
+
+	/* enable both PCMCIA card irqs in the shared line */
+	alchemy_gpio2_enable_int(201);
+	alchemy_gpio2_enable_int(202);
+
+	return 0;
+}
+arch_initcall(pb1550_init_irq);
diff --git a/arch/mips/alchemy/devboards/pb1550/platform.c b/arch/mips/alchemy/devboards/pb1550/platform.c
new file mode 100644
index 0000000..d7150d0
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1550/platform.c
@@ -0,0 +1,69 @@
+/*
+ * Pb1550 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/init.h>
+
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-pb1x00/pb1550.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+#include "../platform.h"
+
+static int __init pb1550_dev_init(void)
+{
+	int swapped;
+
+	/* Pb1550, like all others, also has statuschange irqs; however they're
+	* wired up on one of the Au1550's shared GPIO201_205 line, which also
+	* services the PCMCIA card interrupts.  So we ignore statuschange and
+	* use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
+	* drivers are used to shared irqs and b) statuschange isn't really use-
+	* ful anyway.
+	*/
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR,
+				    PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+				    AU1550_GPIO201_205_INT,
+				    AU1550_GPIO0_INT,
+				    0,
+				    0,
+				    0);
+
+	db1x_register_pcmcia_socket(PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
+				    PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x008000000,
+				    PCMCIA_MEM_PHYS_ADDR  + 0x008400000 - 1,
+				    PCMCIA_IO_PHYS_ADDR   + 0x008000000,
+				    PCMCIA_IO_PHYS_ADDR   + 0x008010000 - 1,
+				    AU1550_GPIO201_205_INT,
+				    AU1550_GPIO1_INT,
+				    0,
+				    0,
+				    1);
+
+	swapped = bcsr_read(BCSR_STATUS) & BCSR_STATUS_PB1550_SWAPBOOT;
+	db1x_register_norflash(128 * 1024 * 1024, 4, swapped);
+
+	return 0;
+}
+device_initcall(pb1550_dev_init);
diff --git a/arch/mips/alchemy/devboards/platform.c b/arch/mips/alchemy/devboards/platform.c
new file mode 100644
index 0000000..49a4b32
--- /dev/null
+++ b/arch/mips/alchemy/devboards/platform.c
@@ -0,0 +1,222 @@
+/*
+ * devoard misc stuff.
+ */
+
+#include <linux/init.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/physmap.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+
+#include <asm/reboot.h>
+#include <asm/mach-db1x00/bcsr.h>
+
+static void db1x_power_off(void)
+{
+	bcsr_write(BCSR_RESETS, 0);
+	bcsr_write(BCSR_SYSTEM, BCSR_SYSTEM_PWROFF | BCSR_SYSTEM_RESET);
+}
+
+static void db1x_reset(char *c)
+{
+	bcsr_write(BCSR_RESETS, 0);
+	bcsr_write(BCSR_SYSTEM, 0);
+}
+
+static int __init db1x_poweroff_setup(void)
+{
+	if (!pm_power_off)
+		pm_power_off = db1x_power_off;
+	if (!_machine_halt)
+		_machine_halt = db1x_power_off;
+	if (!_machine_restart)
+		_machine_restart = db1x_reset;
+
+	return 0;
+}
+late_initcall(db1x_poweroff_setup);
+
+/* register a pcmcia socket */
+int __init db1x_register_pcmcia_socket(phys_addr_t pcmcia_attr_start,
+				       phys_addr_t pcmcia_attr_end,
+				       phys_addr_t pcmcia_mem_start,
+				       phys_addr_t pcmcia_mem_end,
+				       phys_addr_t pcmcia_io_start,
+				       phys_addr_t pcmcia_io_end,
+				       int card_irq,
+				       int cd_irq,
+				       int stschg_irq,
+				       int eject_irq,
+				       int id)
+{
+	int cnt, i, ret;
+	struct resource *sr;
+	struct platform_device *pd;
+
+	cnt = 5;
+	if (eject_irq)
+		cnt++;
+	if (stschg_irq)
+		cnt++;
+
+	sr = kzalloc(sizeof(struct resource) * cnt, GFP_KERNEL);
+	if (!sr)
+		return -ENOMEM;
+
+	pd = platform_device_alloc("db1xxx_pcmcia", id);
+	if (!pd) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	sr[0].name	= "pcmcia-attr";
+	sr[0].flags	= IORESOURCE_MEM;
+	sr[0].start	= pcmcia_attr_start;
+	sr[0].end	= pcmcia_attr_end;
+
+	sr[1].name	= "pcmcia-mem";
+	sr[1].flags	= IORESOURCE_MEM;
+	sr[1].start	= pcmcia_mem_start;
+	sr[1].end	= pcmcia_mem_end;
+
+	sr[2].name	= "pcmcia-io";
+	sr[2].flags	= IORESOURCE_MEM;
+	sr[2].start	= pcmcia_io_start;
+	sr[2].end	= pcmcia_io_end;
+
+	sr[3].name	= "insert";
+	sr[3].flags	= IORESOURCE_IRQ;
+	sr[3].start = sr[3].end = cd_irq;
+
+	sr[4].name	= "card";
+	sr[4].flags	= IORESOURCE_IRQ;
+	sr[4].start = sr[4].end = card_irq;
+
+	i = 5;
+	if (stschg_irq) {
+		sr[i].name	= "stschg";
+		sr[i].flags	= IORESOURCE_IRQ;
+		sr[i].start = sr[i].end = stschg_irq;
+		i++;
+	}
+	if (eject_irq) {
+		sr[i].name	= "eject";
+		sr[i].flags	= IORESOURCE_IRQ;
+		sr[i].start = sr[i].end = eject_irq;
+	}
+
+	pd->resource = sr;
+	pd->num_resources = cnt;
+
+	ret = platform_device_add(pd);
+	if (!ret)
+		return 0;
+
+	platform_device_put(pd);
+out:
+	kfree(sr);
+	return ret;
+}
+
+#define YAMON_SIZE	0x00100000
+#define YAMON_ENV_SIZE	0x00040000
+
+int __init db1x_register_norflash(unsigned long size, int width,
+				  int swapped)
+{
+	struct physmap_flash_data *pfd;
+	struct platform_device *pd;
+	struct mtd_partition *parts;
+	struct resource *res;
+	int ret, i;
+
+	if (size < (8 * 1024 * 1024))
+		return -EINVAL;
+
+	ret = -ENOMEM;
+	parts = kzalloc(sizeof(struct mtd_partition) * 5, GFP_KERNEL);
+	if (!parts)
+		goto out;
+
+	res = kzalloc(sizeof(struct resource), GFP_KERNEL);
+	if (!res)
+		goto out1;
+
+	pfd = kzalloc(sizeof(struct physmap_flash_data), GFP_KERNEL);
+	if (!pfd)
+		goto out2;
+
+	pd = platform_device_alloc("physmap-flash", 0);
+	if (!pd)
+		goto out3;
+
+	/* NOR flash ends at 0x20000000, regardless of size */
+	res->start = 0x20000000 - size;
+	res->end = 0x20000000 - 1;
+	res->flags = IORESOURCE_MEM;
+
+	/* partition setup.  Most Develboards have a switch which allows
+	 * to swap the physical locations of the 2 NOR flash banks.
+	 */
+	i = 0;
+	if (!swapped) {
+		/* first NOR chip */
+		parts[i].offset = 0;
+		parts[i].name = "User FS";
+		parts[i].size = size / 2;
+		i++;
+	}
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "User FS 2";
+	parts[i].size = (size / 2) - (0x20000000 - 0x1fc00000);
+	i++;
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "YAMON";
+	parts[i].size = YAMON_SIZE;
+	parts[i].mask_flags = MTD_WRITEABLE;
+	i++;
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "raw kernel";
+	parts[i].size = 0x00400000 - YAMON_SIZE - YAMON_ENV_SIZE;
+	i++;
+
+	parts[i].offset = MTDPART_OFS_APPEND;
+	parts[i].name = "YAMON Env";
+	parts[i].size = YAMON_ENV_SIZE;
+	parts[i].mask_flags = MTD_WRITEABLE;
+	i++;
+
+	if (swapped) {
+		parts[i].offset = MTDPART_OFS_APPEND;
+		parts[i].name = "User FS";
+		parts[i].size = size / 2;
+		i++;
+	}
+
+	pfd->width = width;
+	pfd->parts = parts;
+	pfd->nr_parts = 5;
+
+	pd->dev.platform_data = pfd;
+	pd->resource = res;
+	pd->num_resources = 1;
+
+	ret = platform_device_add(pd);
+	if (!ret)
+		return ret;
+
+	platform_device_put(pd);
+out3:
+	kfree(pfd);
+out2:
+	kfree(res);
+out1:
+	kfree(parts);
+out:
+	return ret;
+}
diff --git a/arch/mips/alchemy/devboards/platform.h b/arch/mips/alchemy/devboards/platform.h
new file mode 100644
index 0000000..5ac055d
--- /dev/null
+++ b/arch/mips/alchemy/devboards/platform.h
@@ -0,0 +1,21 @@
+#ifndef _DEVBOARD_PLATFORM_H_
+#define _DEVBOARD_PLATFORM_H_
+
+#include <linux/init.h>
+
+int __init db1x_register_pcmcia_socket(phys_addr_t pcmcia_attr_start,
+				       phys_addr_t pcmcia_attr_len,
+				       phys_addr_t pcmcia_mem_start,
+				       phys_addr_t pcmcia_mem_end,
+				       phys_addr_t pcmcia_io_start,
+				       phys_addr_t pcmcia_io_end,
+				       int card_irq,
+				       int cd_irq,
+				       int stschg_irq,
+				       int eject_irq,
+				       int id);
+
+int __init db1x_register_norflash(unsigned long size, int width,
+				  int swapped);
+
+#endif
diff --git a/arch/mips/alchemy/devboards/pm.c b/arch/mips/alchemy/devboards/pm.c
index 632f986..4bbd313 100644
--- a/arch/mips/alchemy/devboards/pm.c
+++ b/arch/mips/alchemy/devboards/pm.c
@@ -10,6 +10,7 @@
 #include <linux/sysfs.h>
 #include <asm/mach-au1x00/au1000.h>
 #include <asm/mach-au1x00/gpio.h>
+#include <asm/mach-db1x00/bcsr.h>
 
 /*
  * Generic suspend userspace interface for Alchemy development boards.
@@ -26,6 +27,20 @@ static unsigned long db1x_pm_last_wakesrc;
 
 static int db1x_pm_enter(suspend_state_t state)
 {
+	unsigned short bcsrs[16];
+	int i, j, hasint;
+
+	/* save CPLD regs */
+	hasint = bcsr_read(BCSR_WHOAMI);
+	hasint = BCSR_WHOAMI_BOARD(hasint) >= BCSR_WHOAMI_DB1200;
+	j = (hasint) ? BCSR_MASKSET : BCSR_SYSTEM;
+
+	for (i = BCSR_STATUS; i <= j; i++)
+		bcsrs[i] = bcsr_read(i);
+
+	/* shut off hexleds */
+	bcsr_write(BCSR_HEXCLEAR, 3);
+
 	/* enable GPIO based wakeup */
 	alchemy_gpio1_input_enable();
 
@@ -52,6 +67,23 @@ static int db1x_pm_enter(suspend_state_t state)
 	/* ...and now the sandman can come! */
 	au_sleep();
 
+
+	/* restore CPLD regs */
+	for (i = BCSR_STATUS; i <= BCSR_SYSTEM; i++)
+		bcsr_write(i, bcsrs[i]);
+
+	/* restore CPLD int registers */
+	if (hasint) {
+		bcsr_write(BCSR_INTCLR, 0xffff);
+		bcsr_write(BCSR_MASKCLR, 0xffff);
+		bcsr_write(BCSR_INTSTAT, 0xffff);
+		bcsr_write(BCSR_INTSET, bcsrs[BCSR_INTSET]);
+		bcsr_write(BCSR_MASKSET, bcsrs[BCSR_MASKSET]);
+	}
+
+	/* light up hexleds */
+	bcsr_write(BCSR_HEXCLEAR, 0);
+
 	return 0;
 }
 
diff --git a/arch/mips/alchemy/devboards/prom.c b/arch/mips/alchemy/devboards/prom.c
index 0042bd6..b30df5c 100644
--- a/arch/mips/alchemy/devboards/prom.c
+++ b/arch/mips/alchemy/devboards/prom.c
@@ -60,3 +60,8 @@ void __init prom_init(void)
 		strict_strtoul(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }
+
+void prom_putchar(unsigned char c)
+{
+    alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+}
diff --git a/arch/mips/alchemy/mtx-1/Makefile b/arch/mips/alchemy/mtx-1/Makefile
index 7c67b3d..4a53815 100644
--- a/arch/mips/alchemy/mtx-1/Makefile
+++ b/arch/mips/alchemy/mtx-1/Makefile
@@ -6,7 +6,7 @@
 # Makefile for 4G Systems MTX-1 board.
 #
 
-lib-y := init.o board_setup.o irqmap.o
+lib-y := init.o board_setup.o
 obj-y := platform.o
 
 EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/mtx-1/board_setup.c b/arch/mips/alchemy/mtx-1/board_setup.c
index 45b61c9..a9f0336 100644
--- a/arch/mips/alchemy/mtx-1/board_setup.c
+++ b/arch/mips/alchemy/mtx-1/board_setup.c
@@ -30,32 +30,43 @@
 
 #include <linux/gpio.h>
 #include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/pm.h>
 
+#include <asm/reboot.h>
 #include <asm/mach-au1x00/au1000.h>
 
 #include <prom.h>
 
+char irq_tab_alchemy[][5] __initdata = {
+	[0] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 00 - AdapterA-Slot0 (top) */
+	[1] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
+	[2] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 02 - AdapterB-Slot0 (top) */
+	[3] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
+	[4] = { -1, AU1500_PCI_INTA, AU1500_PCI_INTB, 0xff, 0xff }, /* IDSEL 04 - AdapterC-Slot0 (top) */
+	[5] = { -1, AU1500_PCI_INTB, AU1500_PCI_INTA, 0xff, 0xff }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
+	[6] = { -1, AU1500_PCI_INTC, AU1500_PCI_INTD, 0xff, 0xff }, /* IDSEL 06 - AdapterD-Slot0 (top) */
+	[7] = { -1, AU1500_PCI_INTD, AU1500_PCI_INTC, 0xff, 0xff }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
+};
+
 extern int (*board_pci_idsel)(unsigned int devsel, int assert);
 int mtx1_pci_idsel(unsigned int devsel, int assert);
 
-void board_reset(void)
+static void mtx1_reset(char *c)
 {
 	/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
 	au_writel(0x00000000, 0xAE00001C);
 }
 
-void __init board_setup(void)
+static void mtx1_power_off(void)
 {
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	char *argptr;
-	argptr = prom_getcmdline();
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
-#endif
+	printk(KERN_ALERT "It's now safe to remove power\n");
+	while (1)
+		asm volatile (".set mips3 ; wait ; .set mips1");
+}
 
+void __init board_setup(void)
+{
 	alchemy_gpio2_enable();
 
 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
@@ -86,6 +97,10 @@ void __init board_setup(void)
 	alchemy_gpio_direction_output(211, 1);	/* green on */
 	alchemy_gpio_direction_output(212, 0);	/* red off */
 
+	pm_power_off = mtx1_power_off;
+	_machine_halt = mtx1_power_off;
+	_machine_restart = mtx1_reset;
+
 	printk(KERN_INFO "4G Systems MTX-1 Board\n");
 }
 
@@ -109,3 +124,15 @@ mtx1_pci_idsel(unsigned int devsel, int assert)
 	au_sync_udelay(1);
 	return 1;
 }
+
+static int __init mtx1_init_irq(void)
+{
+	set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+	set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+
+	return 0;
+}
+arch_initcall(mtx1_init_irq);
diff --git a/arch/mips/alchemy/mtx-1/init.c b/arch/mips/alchemy/mtx-1/init.c
index 5e871c8..f8d2557 100644
--- a/arch/mips/alchemy/mtx-1/init.c
+++ b/arch/mips/alchemy/mtx-1/init.c
@@ -32,6 +32,7 @@
 #include <linux/init.h>
 
 #include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
 
 #include <prom.h>
 
@@ -58,3 +59,8 @@ void __init prom_init(void)
 		strict_strtoul(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }
+
+void prom_putchar(unsigned char c)
+{
+	alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+}
diff --git a/arch/mips/alchemy/mtx-1/irqmap.c b/arch/mips/alchemy/mtx-1/irqmap.c
deleted file mode 100644
index f1ab12a..0000000
--- a/arch/mips/alchemy/mtx-1/irqmap.c
+++ /dev/null
@@ -1,56 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- *	Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- *		dan@embeddededge.com
- *
- *  This program is free software; you can redistribute	 it and/or modify it
- *  under  the terms of	 the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the	License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
- *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
- *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <asm/mach-au1x00/au1000.h>
-
-char irq_tab_alchemy[][5] __initdata = {
-	[0] = { -1, INTA, INTA, INTX, INTX }, /* IDSEL 00 - AdapterA-Slot0 (top) */
-	[1] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 01 - AdapterA-Slot1 (bottom) */
-	[2] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 02 - AdapterB-Slot0 (top) */
-	[3] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 03 - AdapterB-Slot1 (bottom) */
-	[4] = { -1, INTA, INTB, INTX, INTX }, /* IDSEL 04 - AdapterC-Slot0 (top) */
-	[5] = { -1, INTB, INTA, INTX, INTX }, /* IDSEL 05 - AdapterC-Slot1 (bottom) */
-	[6] = { -1, INTC, INTD, INTX, INTX }, /* IDSEL 06 - AdapterD-Slot0 (top) */
-	[7] = { -1, INTD, INTC, INTX, INTX }, /* IDSEL 07 - AdapterD-Slot1 (bottom) */
-};
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-       { AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
-       { AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
-       { AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
-       { AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
-       { AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
-};
-
-
-void __init board_init_irq(void)
-{
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
diff --git a/arch/mips/alchemy/xxs1500/Makefile b/arch/mips/alchemy/xxs1500/Makefile
index db3c526..4dc81d7 100644
--- a/arch/mips/alchemy/xxs1500/Makefile
+++ b/arch/mips/alchemy/xxs1500/Makefile
@@ -5,4 +5,6 @@
 # Makefile for MyCable XXS1500 board.
 #
 
-lib-y := init.o board_setup.o irqmap.o
+lib-y := init.o board_setup.o platform.o
+
+EXTRA_CFLAGS += -Werror
diff --git a/arch/mips/alchemy/xxs1500/board_setup.c b/arch/mips/alchemy/xxs1500/board_setup.c
index 4de2d48..47b4292 100644
--- a/arch/mips/alchemy/xxs1500/board_setup.c
+++ b/arch/mips/alchemy/xxs1500/board_setup.c
@@ -25,31 +25,35 @@
 
 #include <linux/gpio.h>
 #include <linux/init.h>
+#include <linux/interrupt.h>
 #include <linux/delay.h>
+#include <linux/pm.h>
 
+#include <asm/reboot.h>
 #include <asm/mach-au1x00/au1000.h>
 
 #include <prom.h>
 
-void board_reset(void)
+static void xxs1500_reset(char *c)
 {
 	/* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
 	au_writel(0x00000000, 0xAE00001C);
 }
 
+static void xxs1500_power_off(void)
+{
+	printk(KERN_ALERT "It's now safe to remove power\n");
+	while (1)
+		asm volatile (".set mips3 ; wait ; .set mips1");
+}
+
 void __init board_setup(void)
 {
 	u32 pin_func;
 
-#ifdef CONFIG_SERIAL_8250_CONSOLE
-	char *argptr;
-	argptr = prom_getcmdline();
-	argptr = strstr(argptr, "console=");
-	if (argptr == NULL) {
-		argptr = prom_getcmdline();
-		strcat(argptr, " console=ttyS0,115200");
-	}
-#endif
+	pm_power_off = xxs1500_power_off;
+	_machine_halt = xxs1500_power_off;
+	_machine_restart = xxs1500_reset;
 
 	alchemy_gpio1_input_enable();
 	alchemy_gpio2_enable();
@@ -68,22 +72,6 @@ void __init board_setup(void)
 	/* Enable DTR = USB power up */
 	au_writel(0x01, UART3_ADDR + UART_MCR); /* UART_MCR_DTR is 0x01??? */
 
-#ifdef CONFIG_PCMCIA_XXS1500
-	/* GPIO 0, 1, and 4 are inputs */
-	alchemy_gpio_direction_input(0);
-	alchemy_gpio_direction_input(1);
-	alchemy_gpio_direction_input(4);
-
-	/* GPIO2 208/9/10/11 are inputs */
-	alchemy_gpio_direction_input(208);
-	alchemy_gpio_direction_input(209);
-	alchemy_gpio_direction_input(210);
-	alchemy_gpio_direction_input(211);
-
-	/* Turn off power */
-	alchemy_gpio_direction_output(214, 0);
-#endif
-
 #ifdef CONFIG_PCI
 #if defined(__MIPSEB__)
 	au_writel(0xf | (2 << 6) | (1 << 4), Au1500_PCI_CFG);
@@ -92,3 +80,23 @@ void __init board_setup(void)
 #endif
 #endif
 }
+
+static int __init xxs1500_init_irq(void)
+{
+	set_irq_type(AU1500_GPIO204_INT, IRQF_TRIGGER_HIGH);
+	set_irq_type(AU1500_GPIO201_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO202_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO203_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO205_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO207_INT, IRQF_TRIGGER_LOW);
+
+	set_irq_type(AU1500_GPIO0_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO1_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO2_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO3_INT, IRQF_TRIGGER_LOW);
+	set_irq_type(AU1500_GPIO4_INT, IRQF_TRIGGER_LOW); /* CF irq */
+	set_irq_type(AU1500_GPIO5_INT, IRQF_TRIGGER_LOW);
+
+	return 0;
+}
+arch_initcall(xxs1500_init_irq);
diff --git a/arch/mips/alchemy/xxs1500/init.c b/arch/mips/alchemy/xxs1500/init.c
index 456fa14..15125c2 100644
--- a/arch/mips/alchemy/xxs1500/init.c
+++ b/arch/mips/alchemy/xxs1500/init.c
@@ -30,6 +30,7 @@
 #include <linux/kernel.h>
 
 #include <asm/bootinfo.h>
+#include <asm/mach-au1x00/au1000.h>
 
 #include <prom.h>
 
@@ -56,3 +57,8 @@ void __init prom_init(void)
 		strict_strtoul(memsize_str, 0, &memsize);
 	add_memory_region(0, memsize, BOOT_MEM_RAM);
 }
+
+void prom_putchar(unsigned char c)
+{
+	alchemy_uart_putchar(UART0_PHYS_ADDR, c);
+}
diff --git a/arch/mips/alchemy/xxs1500/irqmap.c b/arch/mips/alchemy/xxs1500/irqmap.c
deleted file mode 100644
index 0f0f301..0000000
--- a/arch/mips/alchemy/xxs1500/irqmap.c
+++ /dev/null
@@ -1,52 +0,0 @@
-/*
- * BRIEF MODULE DESCRIPTION
- *	Au1xxx irq map table
- *
- * Copyright 2003 Embedded Edge, LLC
- *		dan@embeddededge.com
- *
- *  This program is free software; you can redistribute	 it and/or modify it
- *  under  the terms of	 the GNU General  Public License as published by the
- *  Free Software Foundation;  either version 2 of the	License, or (at your
- *  option) any later version.
- *
- *  THIS  SOFTWARE  IS PROVIDED	  ``AS	IS'' AND   ANY	EXPRESS OR IMPLIED
- *  WARRANTIES,	  INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
- *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
- *  NO	EVENT  SHALL   THE AUTHOR  BE	 LIABLE FOR ANY	  DIRECT, INDIRECT,
- *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- *  NOT LIMITED	  TO, PROCUREMENT OF  SUBSTITUTE GOODS	OR SERVICES; LOSS OF
- *  USE, DATA,	OR PROFITS; OR	BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- *  ANY THEORY OF LIABILITY, WHETHER IN	 CONTRACT, STRICT LIABILITY, OR TORT
- *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- *  You should have received a copy of the  GNU General Public License along
- *  with this program; if not, write  to the Free Software Foundation, Inc.,
- *  675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <asm/mach-au1x00/au1000.h>
-
-struct au1xxx_irqmap __initdata au1xxx_irq_map[] = {
-	{ AU1500_GPIO_204, IRQF_TRIGGER_HIGH, 0 },
-	{ AU1500_GPIO_201, IRQF_TRIGGER_LOW, 0 },
-	{ AU1500_GPIO_202, IRQF_TRIGGER_LOW, 0 },
-	{ AU1500_GPIO_203, IRQF_TRIGGER_LOW, 0 },
-	{ AU1500_GPIO_205, IRQF_TRIGGER_LOW, 0 },
-	{ AU1500_GPIO_207, IRQF_TRIGGER_LOW, 0 },
-
-	{ AU1000_GPIO_0, IRQF_TRIGGER_LOW, 0 },
-	{ AU1000_GPIO_1, IRQF_TRIGGER_LOW, 0 },
-	{ AU1000_GPIO_2, IRQF_TRIGGER_LOW, 0 },
-	{ AU1000_GPIO_3, IRQF_TRIGGER_LOW, 0 },
-	{ AU1000_GPIO_4, IRQF_TRIGGER_LOW, 0 }, /* CF interrupt */
-	{ AU1000_GPIO_5, IRQF_TRIGGER_LOW, 0 },
-};
-
-void __init board_init_irq(void)
-{
-	au1xxx_setup_irqmap(au1xxx_irq_map, ARRAY_SIZE(au1xxx_irq_map));
-}
diff --git a/arch/mips/alchemy/xxs1500/platform.c b/arch/mips/alchemy/xxs1500/platform.c
new file mode 100644
index 0000000..e87c45c
--- /dev/null
+++ b/arch/mips/alchemy/xxs1500/platform.c
@@ -0,0 +1,63 @@
+/*
+ * XXS1500 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-au1x00/au1000.h>
+
+static struct resource xxs1500_pcmcia_res[] = {
+	{
+		.name	= "pcmcia-io",
+		.flags	= IORESOURCE_MEM,
+		.start	= PCMCIA_IO_PHYS_ADDR,
+		.end	= PCMCIA_IO_PHYS_ADDR + 0x000400000 - 1,
+	},
+	{
+		.name	= "pcmcia-attr",
+		.flags	= IORESOURCE_MEM,
+		.start	= PCMCIA_ATTR_PHYS_ADDR,
+		.end	= PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+	},
+	{
+		.name	= "pcmcia-mem",
+		.flags	= IORESOURCE_MEM,
+		.start	= PCMCIA_MEM_PHYS_ADDR,
+		.end	= PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
+	},
+};
+
+static struct platform_device xxs1500_pcmcia_dev = {
+	.name		= "xxs1500_pcmcia",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(xxs1500_pcmcia_res),
+	.resource	= xxs1500_pcmcia_res,
+};
+
+static struct platform_device *xxs1500_devs[] __initdata = {
+	&xxs1500_pcmcia_dev,
+};
+
+static int __init xxs1500_dev_init(void)
+{
+	return platform_add_devices(xxs1500_devs,
+				    ARRAY_SIZE(xxs1500_devs));
+}
+device_initcall(xxs1500_dev_init);