[PATCH] CRIS update: configuration and build

Changes to configuration and build system.

* Added v32 sub architecture.
* Use generic hard IRQ.
* Added SMP options.
* Added options to OOPS at NMI and reboot at OOM.
* Made it possible to set objtree.
* Added option to select Kernel GDB serial port.
* Corrected Kconfig usage.
* Added system profiler.

Signed-off-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

5 files changed, 150 insertions, 228 deletions

diff --git a/arch/cris/arch-v10/Kconfig b/arch/cris/arch-v10/Kconfig
index 2ca64cc..44eb1b9 100644
--- a/arch/cris/arch-v10/Kconfig
+++ b/arch/cris/arch-v10/Kconfig
@@ -260,6 +260,37 @@ config ETRAX_DEBUG_PORT_NULL
 endchoice
 
 choice
+	prompt "Kernel GDB port"
+	depends on ETRAX_KGDB
+	default ETRAX_KGDB_PORT0
+	help
+	  Choose a serial port for kernel debugging.  NOTE: This port should
+	  not be enabled under Drivers for built-in interfaces (as it has its
+	  own initialization code) and should not be the same as the debug port.
+
+config ETRAX_KGDB_PORT0
+	bool "Serial-0"
+	help
+	  Use serial port 0 for kernel debugging.
+
+config ETRAX_KGDB_PORT1
+	bool "Serial-1"
+	help
+	  Use serial port 1 for kernel debugging.
+
+config ETRAX_KGDB_PORT2
+	bool "Serial-2"
+	help
+	  Use serial port 2 for kernel debugging.
+
+config ETRAX_KGDB_PORT3
+	bool "Serial-3"
+	help
+	  Use serial port 3 for kernel debugging.
+
+endchoice
+
+choice
 	prompt "Product rescue-port"
 	depends on ETRAX_ARCH_V10
 	default ETRAX_RESCUE_SER0
diff --git a/arch/cris/arch-v10/boot/Makefile b/arch/cris/arch-v10/boot/Makefile
index fe66503..e5b1058 100644
--- a/arch/cris/arch-v10/boot/Makefile
+++ b/arch/cris/arch-v10/boot/Makefile
@@ -1,12 +1,13 @@
 #
 # arch/cris/boot/Makefile
 #
+target = $(target_boot_dir)
+src    = $(src_boot_dir)
 
 zImage: compressed/vmlinuz
 
-compressed/vmlinuz: $(TOPDIR)/vmlinux
-	@$(MAKE) -C compressed vmlinuz
+compressed/vmlinuz:
+	@$(MAKE) -f $(src)/compressed/Makefile $(target_compressed_dir)/vmlinuz
 
 clean:
-	rm -f zImage tools/build compressed/vmlinux.out
-	@$(MAKE) -C compressed clean
+	@$(MAKE) -f $(src)/compressed/Makefile clean
diff --git a/arch/cris/arch-v10/boot/compressed/Makefile b/arch/cris/arch-v10/boot/compressed/Makefile
index 5f71c2c..6584a44 100644
--- a/arch/cris/arch-v10/boot/compressed/Makefile
+++ b/arch/cris/arch-v10/boot/compressed/Makefile
@@ -1,40 +1,45 @@
 #
-# linux/arch/etrax100/boot/compressed/Makefile
-#
-# create a compressed vmlinux image from the original vmlinux files and romfs
+# create a compressed vmlinuz image from the binary vmlinux.bin file
 #
+target = $(target_compressed_dir)
+src    = $(src_compressed_dir)
 
-CC = gcc-cris -melf -I $(TOPDIR)/include
+CC = gcc-cris -melf $(LINUXINCLUDE)
 CFLAGS = -O2
 LD = ld-cris
 OBJCOPY = objcopy-cris
 OBJCOPYFLAGS = -O binary --remove-section=.bss
-OBJECTS = head.o misc.o
+OBJECTS = $(target)/head.o $(target)/misc.o
 
 # files to compress
-SYSTEM = $(TOPDIR)/vmlinux.bin
+SYSTEM = $(objtree)/vmlinux.bin
 
-all: vmlinuz
+all: $(target_compressed_dir)/vmlinuz
 
-decompress.bin: $(OBJECTS)
-	$(LD) -T decompress.ld -o decompress.o $(OBJECTS)
-	$(OBJCOPY) $(OBJCOPYFLAGS) decompress.o decompress.bin
-# save it for mkprod in the topdir.
-	cp decompress.bin $(TOPDIR)
+$(target)/decompress.bin: $(OBJECTS)
+	$(LD) -T $(src)/decompress.ld -o $(target)/decompress.o $(OBJECTS)
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/decompress.o $(target)/decompress.bin
 
+# Create vmlinuz image in top-level build directory
+$(target_compressed_dir)/vmlinuz: $(target) piggy.img $(target)/decompress.bin
+	@echo "  COMPR   vmlinux.bin --> vmlinuz"
+	@cat $(target)/decompress.bin piggy.img > $(target_compressed_dir)/vmlinuz
+	@rm -f piggy.img
 
-vmlinuz: piggy.img decompress.bin
-	cat decompress.bin piggy.img > vmlinuz
-	rm -f piggy.img
+$(target)/head.o: $(src)/head.S
+	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $@
 
-head.o: head.S
-	$(CC) -D__ASSEMBLY__ -traditional -c head.S -o head.o
+$(target)/misc.o: $(src)/misc.c
+	$(CC) -D__KERNEL__ -c $< -o $@
 
 # gzip the kernel image
 
 piggy.img: $(SYSTEM)
-	cat $(SYSTEM) | gzip -f -9 > piggy.img
+	@cat $(SYSTEM) | gzip -f -9 > piggy.img
+
+$(target):
+	mkdir -p $(target)
 
 clean:
-	rm -f piggy.img vmlinuz vmlinuz.o
+	rm -f piggy.img $(objtree)/vmlinuz
 
diff --git a/arch/cris/arch-v10/boot/rescue/Makefile b/arch/cris/arch-v10/boot/rescue/Makefile
index e9f2ba2..8be9b31 100644
--- a/arch/cris/arch-v10/boot/rescue/Makefile
+++ b/arch/cris/arch-v10/boot/rescue/Makefile
@@ -1,52 +1,53 @@
 #
 # Makefile for rescue code
 #
-ifndef TOPDIR
-TOPDIR = ../../../..
-endif
-CC = gcc-cris -mlinux -I $(TOPDIR)/include
+target = $(target_rescue_dir)
+src    = $(src_rescue_dir)
+
+CC = gcc-cris -mlinux $(LINUXINCLUDE)
 CFLAGS = -O2
 LD = gcc-cris -mlinux -nostdlib
 OBJCOPY = objcopy-cris
 OBJCOPYFLAGS = -O binary --remove-section=.bss
 
-all: rescue.bin testrescue.bin kimagerescue.bin
-
-rescue: rescue.bin
-	# do nothing
+all: $(target)/rescue.bin $(target)/testrescue.bin $(target)/kimagerescue.bin
 
-rescue.bin: head.o
-	$(LD) -T rescue.ld -o rescue.o head.o
-	$(OBJCOPY) $(OBJCOPYFLAGS) rescue.o rescue.bin
-	cp rescue.bin $(TOPDIR)
+$(target)/rescue.bin: $(target) $(target)/head.o
+	$(LD) -T $(src)/rescue.ld -o $(target)/rescue.o $(target)/head.o
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/rescue.o $(target)/rescue.bin
+# Place a copy in top-level build directory
+	cp -p $(target)/rescue.bin $(objtree)
 
-testrescue.bin: testrescue.o
-	$(OBJCOPY) $(OBJCOPYFLAGS) testrescue.o tr.bin
+$(target)/testrescue.bin: $(target) $(target)/testrescue.o
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/testrescue.o tr.bin
 # Pad it to 784 bytes
 	dd if=/dev/zero of=tmp2423 bs=1 count=784
 	cat tr.bin tmp2423 >testrescue_tmp.bin
-	dd if=testrescue_tmp.bin of=testrescue.bin bs=1 count=784
+	dd if=testrescue_tmp.bin of=$(target)/testrescue.bin bs=1 count=784
 	rm tr.bin tmp2423 testrescue_tmp.bin
 
-kimagerescue.bin: kimagerescue.o
-	$(OBJCOPY) $(OBJCOPYFLAGS) kimagerescue.o ktr.bin
+$(target)/kimagerescue.bin: $(target) $(target)/kimagerescue.o
+	$(OBJCOPY) $(OBJCOPYFLAGS) $(target)/kimagerescue.o ktr.bin
 # Pad it to 784 bytes, that's what the rescue loader expects
 	dd if=/dev/zero of=tmp2423 bs=1 count=784
 	cat ktr.bin tmp2423 >kimagerescue_tmp.bin
-	dd if=kimagerescue_tmp.bin of=kimagerescue.bin bs=1 count=784
+	dd if=kimagerescue_tmp.bin of=$(target)/kimagerescue.bin bs=1 count=784
 	rm ktr.bin tmp2423 kimagerescue_tmp.bin
 
-head.o: head.S
+$(target):
+	mkdir -p $(target)
+
+$(target)/head.o: $(src)/head.S
 	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o
 
-testrescue.o: testrescue.S
+$(target)/testrescue.o: $(src)/testrescue.S
 	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o
 
-kimagerescue.o: kimagerescue.S
+$(target)/kimagerescue.o: $(src)/kimagerescue.S
 	$(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o
 
 clean:
-	rm -f *.o *.bin
+	rm -f $(target)/*.o $(target)/*.bin
 
 fastdep:
 
diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig
index 748374f..8b50e84 100644
--- a/arch/cris/arch-v10/drivers/Kconfig
+++ b/arch/cris/arch-v10/drivers/Kconfig
@@ -1,17 +1,11 @@
 config ETRAX_ETHERNET
 	bool "Ethernet support"
 	depends on ETRAX_ARCH_V10
+	select NET_ETHERNET
 	help
 	  This option enables the ETRAX 100LX built-in 10/100Mbit Ethernet
 	  controller.
 
-# this is just so that the user does not have to go into the
-# normal ethernet driver section just to enable ethernetworking
-config NET_ETHERNET
-	bool
-	depends on ETRAX_ETHERNET
-	default y
-
 choice
 	prompt "Network LED behavior"
 	depends on ETRAX_ETHERNET
@@ -20,26 +14,26 @@ choice
 config ETRAX_NETWORK_LED_ON_WHEN_LINK
 	bool "LED_on_when_link"
 	help
-	  Selecting LED_on_when_link will light the LED when there is a 
-	  connection and will flash off when there is activity. 
+	  Selecting LED_on_when_link will light the LED when there is a
+	  connection and will flash off when there is activity.
 
-	  Selecting LED_on_when_activity will light the LED only when 
+	  Selecting LED_on_when_activity will light the LED only when
 	  there is activity.
 
-	  This setting will also affect the behaviour of other activity LEDs 
-	  e.g. Bluetooth. 
+	  This setting will also affect the behaviour of other activity LEDs
+	  e.g. Bluetooth.
 
 config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY
 	bool "LED_on_when_activity"
 	help
-	  Selecting LED_on_when_link will light the LED when there is a 
-	  connection and will flash off when there is activity. 
+	  Selecting LED_on_when_link will light the LED when there is a
+	  connection and will flash off when there is activity.
 
-	  Selecting LED_on_when_activity will light the LED only when 
+	  Selecting LED_on_when_activity will light the LED only when
 	  there is activity.
 
-	  This setting will also affect the behaviour of other activity LEDs 
-	  e.g. Bluetooth. 
+	  This setting will also affect the behaviour of other activity LEDs
+	  e.g. Bluetooth.
 
 endchoice
 
@@ -91,11 +85,11 @@ choice
 	depends on ETRAX_SERIAL_PORT0
 	default ETRAX_SERIAL_PORT0_DMA6_OUT
 
-config CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT0_NO_DMA_OUT
+	bool "No DMA out"
 
-config CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT
-       bool "DMA 6"
+config ETRAX_SERIAL_PORT0_DMA6_OUT
+	bool "DMA 6"
 
 endchoice
 
@@ -104,11 +98,11 @@ choice
 	depends on ETRAX_SERIAL_PORT0
 	default ETRAX_SERIAL_PORT0_DMA7_IN
 
-config CONFIG_ETRAX_SERIAL_PORT0_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT0_NO_DMA_IN
+	bool "No DMA in"
 
-config CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN
-       bool "DMA 7"
+config ETRAX_SERIAL_PORT0_DMA7_IN
+	bool "DMA 7"
 
 endchoice
 
@@ -205,11 +199,11 @@ choice
 	depends on ETRAX_SERIAL_PORT1
 	default ETRAX_SERIAL_PORT1_DMA8_OUT
 
-config CONFIG_ETRAX_SERIAL_PORT1_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT1_NO_DMA_OUT
+	bool "No DMA out"
 
-config CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT
-       bool "DMA 8"
+config ETRAX_SERIAL_PORT1_DMA8_OUT
+	bool "DMA 8"
 
 endchoice
 
@@ -218,11 +212,11 @@ choice
 	depends on ETRAX_SERIAL_PORT1
 	default ETRAX_SERIAL_PORT1_DMA9_IN
 
-config CONFIG_ETRAX_SERIAL_PORT1_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT1_NO_DMA_IN
+	bool "No DMA in"
 
-config CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN
-       bool "DMA 9"
+config ETRAX_SERIAL_PORT1_DMA9_IN
+	bool "DMA 9"
 
 endchoice
 
@@ -308,7 +302,7 @@ config ETRAX_SER1_CD_ON_PB_BIT
 	  Specify the pin of the PB port to carry the CD signal for serial
 	  port 1.
 
-comment "Make sure you dont have the same PB bits more than once!"
+comment "Make sure you do not have the same PB bits more than once!"
 	depends on ETRAX_SERIAL && ETRAX_SER0_DTR_RI_DSR_CD_ON_PB && ETRAX_SER1_DTR_RI_DSR_CD_ON_PB
 
 config ETRAX_SERIAL_PORT2
@@ -322,11 +316,11 @@ choice
 	depends on ETRAX_SERIAL_PORT2
 	default ETRAX_SERIAL_PORT2_DMA2_OUT
 
-config CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT2_NO_DMA_OUT
+	bool "No DMA out"
 
-config CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT
-       bool "DMA 2"
+config ETRAX_SERIAL_PORT2_DMA2_OUT
+	bool "DMA 2"
 
 endchoice
 
@@ -335,11 +329,11 @@ choice
 	depends on ETRAX_SERIAL_PORT2
 	default ETRAX_SERIAL_PORT2_DMA3_IN
 
-config CONFIG_ETRAX_SERIAL_PORT2_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT2_NO_DMA_IN
+	bool "No DMA in"
 
-config CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN
-       bool "DMA 3"
+config ETRAX_SERIAL_PORT2_DMA3_IN
+	bool "DMA 3"
 
 endchoice
 
@@ -436,11 +430,11 @@ choice
 	depends on ETRAX_SERIAL_PORT3
 	default ETRAX_SERIAL_PORT3_DMA4_OUT
 
-config CONFIG_ETRAX_SERIAL_PORT3_NO_DMA_OUT
-       bool "No DMA out"
+config ETRAX_SERIAL_PORT3_NO_DMA_OUT
+	bool "No DMA out"
 
-config CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT
-       bool "DMA 4"
+config ETRAX_SERIAL_PORT3_DMA4_OUT
+	bool "DMA 4"
 
 endchoice
 
@@ -449,11 +443,11 @@ choice
 	depends on ETRAX_SERIAL_PORT3
 	default ETRAX_SERIAL_PORT3_DMA5_IN
 
-config CONFIG_ETRAX_SERIAL_PORT3_NO_DMA_IN
-       bool "No DMA in"
+config ETRAX_SERIAL_PORT3_NO_DMA_IN
+	bool "No DMA in"
 
-config CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN
-       bool "DMA 5"
+config ETRAX_SERIAL_PORT3_DMA5_IN
+	bool "DMA 5"
 
 endchoice
 
@@ -554,7 +548,6 @@ config ETRAX_IDE
 	select BLK_DEV_IDEDISK
 	select BLK_DEV_IDECD
 	select BLK_DEV_IDEDMA
-	select DMA_NONPCI
 	help
 	  Enable this to get support for ATA/IDE.
 	  You can't use paralell ports or SCSI ports
@@ -579,7 +572,7 @@ config ETRAX_IDE_PB7_RESET
 	  IDE reset on pin 7 on port B
 
 config ETRAX_IDE_G27_RESET
-        bool "Port_G_Bit_27"
+	bool "Port_G_Bit_27"
 	help
 	  IDE reset on pin 27 on port G
 
@@ -588,30 +581,36 @@ endchoice
 
 config ETRAX_USB_HOST
 	bool "USB host"
+	select USB
 	help
 	   This option enables the host functionality of the ETRAX 100LX
 	   built-in USB controller. In host mode the controller is designed
 	   for CTRL and BULK traffic only, INTR traffic may work as well
 	   however (depending on the requirements of timeliness).
 
-config USB
-       tristate
-       depends on ETRAX_USB_HOST
-       default y
-
 config ETRAX_USB_HOST_PORT1
-       bool "  USB port 1 enabled"
-       depends on ETRAX_USB_HOST
-       default n
+	bool "USB port 1 enabled"
+	depends on ETRAX_USB_HOST
+	default n
 
 config ETRAX_USB_HOST_PORT2
-       bool "  USB port 2 enabled"
-       depends on ETRAX_USB_HOST
-       default n
+	bool "USB port 2 enabled"
+	depends on ETRAX_USB_HOST
+	default n
 
 config ETRAX_AXISFLASHMAP
 	bool "Axis flash-map support"
 	depends on ETRAX_ARCH_V10
+	select MTD
+	select MTD_CFI
+	select MTD_CFI_AMDSTD
+	select MTD_OBSOLETE_CHIPS
+	select MTD_AMDSTD
+	select MTD_CHAR
+	select MTD_BLOCK
+	select MTD_PARTITIONS
+	select MTD_CONCAT
+	select MTD_COMPLEX_MAPPINGS
 	help
 	  This option enables MTD mapping of flash devices.  Needed to use
 	  flash memories.  If unsure, say Y.
@@ -627,119 +626,6 @@ config ETRAX_PTABLE_SECTOR
 	  for changing this is when the flash block size is bigger
 	  than 64kB (e.g. when using two parallel 16 bit flashes).
 
-# here we define the CONFIG_'s necessary to enable MTD support
-# for the flash
-config MTD
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  Memory Technology Devices are flash, RAM and similar chips, often
-	  used for solid state file systems on embedded devices. This option
-	  will provide the generic support for MTD drivers to register
-	  themselves with the kernel and for potential users of MTD devices
-	  to enumerate the devices which are present and obtain a handle on
-	  them. It will also allow you to select individual drivers for 
-	  particular hardware and users of MTD devices. If unsure, say N.
-
-config MTD_CFI
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  The Common Flash Interface specification was developed by Intel,
-	  AMD and other flash manufactures that provides a universal method
-	  for probing the capabilities of flash devices. If you wish to
-	  support any device that is CFI-compliant, you need to enable this
-	  option. Visit <http://www.amd.com/products/nvd/overview/cfi.html>
-	  for more information on CFI.
-
-config MTD_CFI_AMDSTD
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  The Common Flash Interface defines a number of different command
-	  sets which a CFI-compliant chip may claim to implement. This code
-	  provides support for one of those command sets, used on chips 
-	  chips including the AMD Am29LV320.
-
-config MTD_OBSOLETE_CHIPS
-	bool
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  This option does not enable any code directly, but will allow you to
-	  select some other chip drivers which are now considered obsolete,
-	  because the generic CONFIG_JEDEC_PROBE code above should now detect
-	  the chips which are supported by these drivers, and allow the generic
-	  CFI-compatible drivers to drive the chips. Say 'N' here unless you have
-	  already tried the CONFIG_JEDEC_PROBE method and reported its failure
-	  to the MTD mailing list at <linux-mtd@lists.infradead.org>
-
-config MTD_AMDSTD
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  This option enables support for flash chips using AMD-compatible
-	  commands, including some which are not CFI-compatible and hence 
-	  cannot be used with the CONFIG_MTD_CFI_AMDSTD option.
-
-	  It also works on AMD compatible chips that do conform to CFI.
-
-config MTD_CHAR
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  This provides a character device for each MTD device present in
-	  the system, allowing the user to read and write directly to the
-	  memory chips, and also use ioctl() to obtain information about
-	  the device, or to erase parts of it.
-
-config MTD_BLOCK
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	---help---
-	  Although most flash chips have an erase size too large to be useful
-	  as block devices, it is possible to use MTD devices which are based
-	  on RAM chips in this manner. This block device is a user of MTD
-	  devices performing that function.
-
-	  At the moment, it is also required for the Journalling Flash File
-	  System(s) to obtain a handle on the MTD device when it's mounted
-	  (although JFFS and JFFS2 don't actually use any of the functionality
-	  of the mtdblock device).
-
-	  Later, it may be extended to perform read/erase/modify/write cycles
-	  on flash chips to emulate a smaller block size. Needless to say,
-	  this is very unsafe, but could be useful for file systems which are
-	  almost never written to.
-
-	  You do not need this option for use with the DiskOnChip devices. For
-	  those, enable NFTL support (CONFIG_NFTL) instead.
-
-config MTD_PARTITIONS
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-	help
-	  If you have a device which needs to divide its flash chip(s) up
-	  into multiple 'partitions', each of which appears to the user as
-	  a separate MTD device, you require this option to be enabled. If
-	  unsure, say 'Y'.
-
-	  Note, however, that you don't need this option for the DiskOnChip
-	  devices. Partitioning on NFTL 'devices' is a different - that's the
-	  'normal' form of partitioning used on a block device.
-
-config MTD_CONCAT
-	tristate
-	depends on ETRAX_AXISFLASHMAP
-	default y
-
 config ETRAX_I2C
 	bool "I2C support"
 	depends on ETRAX_ARCH_V10
@@ -752,7 +638,7 @@ config ETRAX_I2C
 	  val = ioctl(fd, _IO(ETRAXI2C_IOCTYPE, I2C_READREG), i2c_arg);
 
 # this is true for most products since PB-I2C seems to be somewhat
-# flawed.. 
+# flawed..
 config ETRAX_I2C_USES_PB_NOT_PB_I2C
 	bool "I2C uses PB not PB-I2C"
 	depends on ETRAX_I2C
@@ -886,7 +772,7 @@ config ETRAX_RTC
 	bool "Real Time Clock support"
 	depends on ETRAX_ARCH_V10
 	help
-	  Enables drivers for the Real-Time Clock battery-backed chips on 
+	  Enables drivers for the Real-Time Clock battery-backed chips on
 	  some products. The kernel reads the time when booting, and
 	  the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a
 	  rtc_time struct (see <file:include/asm-cris/rtc.h>) on the /dev/rtc
@@ -903,13 +789,13 @@ config ETRAX_DS1302
 	bool "DS1302"
 	help
 	  Enables the driver for the DS1302 Real-Time Clock battery-backed
-	  chip on some products. 
+	  chip on some products.
 
 config ETRAX_PCF8563
 	bool "PCF8563"
 	help
 	  Enables the driver for the PCF8563 Real-Time Clock battery-backed
-	  chip on some products.  
+	  chip on some products.
 
 endchoice
 
@@ -954,10 +840,8 @@ config ETRAX_DS1302_TRICKLE_CHARGE
 	help
 	  This controls the initial value of the trickle charge register.
 	  0 = disabled (use this if you are unsure or have a non rechargable battery)
-	  Otherwise the following values can be OR:ed together to control the 
+	  Otherwise the following values can be OR:ed together to control the
 	  charge current:
 	  1 = 2kohm, 2 = 4kohm, 3 = 4kohm
 	  4 = 1 diode, 8 = 2 diodes
 	  Allowed values are (increasing current): 0, 11, 10, 9, 7, 6, 5
-
-