[AVR32] leds-gpio for stk1000

Add GPIO led support: J2 to either block of LEDs on the STK1000.

This uses the new LEDS_GPIO driver, and sets up a heartbeat trigger by
default ... either bright (!!) amber, or a more interesting purple.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>

2 files changed, 88 insertions, 0 deletions

diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig
index 71bc7d3..718578f 100644
--- a/arch/avr32/boards/atstk1000/Kconfig
+++ b/arch/avr32/boards/atstk1000/Kconfig
@@ -50,4 +50,30 @@ config BOARD_ATSTK1002_SPI1
 	  GPIO lines and accessed through the J1 jumper block.  Say "y"
 	  here to configure that SPI controller.
 
+config BOARD_ATSTK1002_J2_LED
+	bool
+	default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB
+
+choice
+	prompt "LEDs connected to J2:"
+	depends on LEDS_GPIO && !BOARD_ATSTK1002_SW4_CUSTOM
+	optional
+	help
+	  Select this if you have jumpered the J2 jumper block to the
+	  LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
+	  IDC cable.  A default "heartbeat" trigger is provided, but
+	  you can of course override this.
+
+config BOARD_ATSTK1002_J2_LED8
+	bool "LED0..LED7"
+	help
+	  Select this if J2 is jumpered to LED0..LED7 amber leds.
+
+config BOARD_ATSTK1002_J2_RGB
+	bool "RGB leds"
+	help
+	  Select this if J2 is jumpered to the RGB leds.
+
+endchoice
+
 endif	# stk 1002
diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c
index cb93eab..c9981b7 100644
--- a/arch/avr32/boards/atstk1000/atstk1002.c
+++ b/arch/avr32/boards/atstk1000/atstk1002.c
@@ -11,6 +11,7 @@
 #include <linux/etherdevice.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
+#include <linux/leds.h>
 #include <linux/platform_device.h>
 #include <linux/string.h>
 #include <linux/types.h>
@@ -120,6 +121,65 @@ static void __init set_hw_addr(struct platform_device *pdev)
 	clk_put(pclk);
 }
 
+#ifdef CONFIG_BOARD_ATSTK1002_J2_LED
+
+static struct gpio_led stk_j2_led[] = {
+#ifdef CONFIG_BOARD_ATSTK1002_J2_LED8
+#define LEDSTRING "J2 jumpered to LED8"
+	{ .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), },
+	{ .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), },
+	{ .name = "led2:amber", .gpio = GPIO_PIN_PB(10), },
+	{ .name = "led3:amber", .gpio = GPIO_PIN_PB(13), },
+	{ .name = "led4:amber", .gpio = GPIO_PIN_PB(14), },
+	{ .name = "led5:amber", .gpio = GPIO_PIN_PB(15), },
+	{ .name = "led6:amber", .gpio = GPIO_PIN_PB(16), },
+	{ .name = "led7:amber", .gpio = GPIO_PIN_PB(30),
+			.default_trigger = "heartbeat", },
+#else	/* RGB */
+#define LEDSTRING "J2 jumpered to RGB LEDs"
+	{ .name = "r1:red",     .gpio = GPIO_PIN_PB( 8), },
+	{ .name = "g1:green",   .gpio = GPIO_PIN_PB(10), },
+	{ .name = "b1:blue",    .gpio = GPIO_PIN_PB(14), },
+
+	{ .name = "r2:red",     .gpio = GPIO_PIN_PB( 9),
+			.default_trigger = "heartbeat", },
+	{ .name = "g2:green",   .gpio = GPIO_PIN_PB(13), },
+	{ .name = "b2:blue",    .gpio = GPIO_PIN_PB(15),
+			.default_trigger = "heartbeat", },
+	/* PB16, PB30 unused */
+#endif
+};
+
+static struct gpio_led_platform_data stk_j2_led_data = {
+	.num_leds	= ARRAY_SIZE(stk_j2_led),
+	.leds		= stk_j2_led,
+};
+
+static struct platform_device stk_j2_led_dev = {
+	.name		= "leds-gpio",
+	.id		= 2,	/* gpio block J2 */
+	.dev		= {
+		.platform_data	= &stk_j2_led_data,
+	},
+};
+
+static void setup_j2_leds(void)
+{
+	unsigned	i;
+
+	for (i = 0; i < ARRAY_SIZE(stk_j2_led); i++)
+		at32_select_gpio(stk_j2_led[i].gpio, AT32_GPIOF_OUTPUT);
+
+	printk("STK1002: " LEDSTRING "\n");
+	platform_device_register(&stk_j2_led_dev);
+}
+
+#else
+static void setup_j2_leds(void)
+{
+}
+#endif
+
 void __init setup_board(void)
 {
 #ifdef	CONFIG_BOARD_ATSTK1002_SW2_CUSTOM
@@ -185,6 +245,8 @@ static int __init atstk1002_init(void)
 	at32_add_device_ssc(0, ATMEL_SSC_TX);
 #endif
 
+	setup_j2_leds();
+
 	return 0;
 }
 postcore_initcall(atstk1002_init);