[ARM] pxa: move ssp into common plat-pxa

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

4 files changed, 425 insertions, 0 deletions

diff --git a/arch/arm/plat-pxa/Kconfig b/arch/arm/plat-pxa/Kconfig
index b158e98..da53395 100644
--- a/arch/arm/plat-pxa/Kconfig
+++ b/arch/arm/plat-pxa/Kconfig
@@ -1,3 +1,8 @@
 if PLAT_PXA
 
+config PXA_SSP
+	tristate
+	help
+	  Enable support for PXA2xx SSP ports
+
 endif
diff --git a/arch/arm/plat-pxa/Makefile b/arch/arm/plat-pxa/Makefile
index 0264bfb..4aacdd1 100644
--- a/arch/arm/plat-pxa/Makefile
+++ b/arch/arm/plat-pxa/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_PXA3xx)		+= mfp.o
 obj-$(CONFIG_ARCH_MMP)		+= mfp.o
 
 obj-$(CONFIG_HAVE_PWM)		+= pwm.o
+obj-$(CONFIG_PXA_SSP)		+= ssp.o
diff --git a/arch/arm/plat-pxa/include/plat/ssp.h b/arch/arm/plat-pxa/include/plat/ssp.h
new file mode 100644
index 0000000..4c4ce62
--- /dev/null
+++ b/arch/arm/plat-pxa/include/plat/ssp.h
@@ -0,0 +1,196 @@
+/*
+ *  ssp.h
+ *
+ *  Copyright (C) 2003 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This driver supports the following PXA CPU/SSP ports:-
+ *
+ *       PXA250     SSP
+ *       PXA255     SSP, NSSP
+ *       PXA26x     SSP, NSSP, ASSP
+ *       PXA27x     SSP1, SSP2, SSP3
+ *       PXA3xx     SSP1, SSP2, SSP3, SSP4
+ */
+
+#ifndef __ASM_ARCH_SSP_H
+#define __ASM_ARCH_SSP_H
+
+#include <linux/list.h>
+#include <linux/io.h>
+
+/*
+ * SSP Serial Port Registers
+ * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
+ * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
+ */
+
+#define SSCR0		(0x00)  /* SSP Control Register 0 */
+#define SSCR1		(0x04)  /* SSP Control Register 1 */
+#define SSSR		(0x08)  /* SSP Status Register */
+#define SSITR		(0x0C)  /* SSP Interrupt Test Register */
+#define SSDR		(0x10)  /* SSP Data Write/Data Read Register */
+
+#define SSTO		(0x28)  /* SSP Time Out Register */
+#define SSPSP		(0x2C)  /* SSP Programmable Serial Protocol */
+#define SSTSA		(0x30)  /* SSP Tx Timeslot Active */
+#define SSRSA		(0x34)  /* SSP Rx Timeslot Active */
+#define SSTSS		(0x38)  /* SSP Timeslot Status */
+#define SSACD		(0x3C)  /* SSP Audio Clock Divider */
+
+#if defined(CONFIG_PXA3xx)
+#define SSACDD		(0x40)	/* SSP Audio Clock Dither Divider */
+#endif
+
+/* Common PXA2xx bits first */
+#define SSCR0_DSS	(0x0000000f)	/* Data Size Select (mask) */
+#define SSCR0_DataSize(x)  ((x) - 1)	/* Data Size Select [4..16] */
+#define SSCR0_FRF	(0x00000030)	/* FRame Format (mask) */
+#define SSCR0_Motorola	(0x0 << 4)	/* Motorola's Serial Peripheral Interface (SPI) */
+#define SSCR0_TI	(0x1 << 4)	/* Texas Instruments' Synchronous Serial Protocol (SSP) */
+#define SSCR0_National	(0x2 << 4)	/* National Microwire */
+#define SSCR0_ECS	(1 << 6)	/* External clock select */
+#define SSCR0_SSE	(1 << 7)	/* Synchronous Serial Port Enable */
+#define SSCR0_SCR(x)	((x) << 8)	/* Serial Clock Rate (mask) */
+
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+#define SSCR0_EDSS	(1 << 20)	/* Extended data size select */
+#define SSCR0_NCS	(1 << 21)	/* Network clock select */
+#define SSCR0_RIM	(1 << 22)	/* Receive FIFO overrrun interrupt mask */
+#define SSCR0_TUM	(1 << 23)	/* Transmit FIFO underrun interrupt mask */
+#define SSCR0_FRDC	(0x07000000)	/* Frame rate divider control (mask) */
+#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24)	/* Time slots per frame [1..8] */
+#define SSCR0_ACS	(1 << 30)	/* Audio clock select */
+#define SSCR0_MOD	(1 << 31)	/* Mode (normal or network) */
+#endif
+
+#if defined(CONFIG_PXA3xx)
+#define SSCR0_FPCKE	(1 << 29)	/* FIFO packing enable */
+#endif
+
+#define SSCR1_RIE	(1 << 0)	/* Receive FIFO Interrupt Enable */
+#define SSCR1_TIE	(1 << 1)	/* Transmit FIFO Interrupt Enable */
+#define SSCR1_LBM	(1 << 2)	/* Loop-Back Mode */
+#define SSCR1_SPO	(1 << 3)	/* Motorola SPI SSPSCLK polarity setting */
+#define SSCR1_SPH	(1 << 4)	/* Motorola SPI SSPSCLK phase setting */
+#define SSCR1_MWDS	(1 << 5)	/* Microwire Transmit Data Size */
+#define SSCR1_TFT	(0x000003c0)	/* Transmit FIFO Threshold (mask) */
+#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
+#define SSCR1_RFT	(0x00003c00)	/* Receive FIFO Threshold (mask) */
+#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
+
+#define SSSR_TNF	(1 << 2)	/* Transmit FIFO Not Full */
+#define SSSR_RNE	(1 << 3)	/* Receive FIFO Not Empty */
+#define SSSR_BSY	(1 << 4)	/* SSP Busy */
+#define SSSR_TFS	(1 << 5)	/* Transmit FIFO Service Request */
+#define SSSR_RFS	(1 << 6)	/* Receive FIFO Service Request */
+#define SSSR_ROR	(1 << 7)	/* Receive FIFO Overrun */
+
+#define SSCR0_TIM		(1 << 23)	/* Transmit FIFO Under Run Interrupt Mask */
+#define SSCR0_RIM		(1 << 22)	/* Receive FIFO Over Run interrupt Mask */
+#define SSCR0_NCS		(1 << 21)	/* Network Clock Select */
+#define SSCR0_EDSS		(1 << 20)	/* Extended Data Size Select */
+
+/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
+#define SSCR0_TISSP		(1 << 4)	/* TI Sync Serial Protocol */
+#define SSCR0_PSP		(3 << 4)	/* PSP - Programmable Serial Protocol */
+#define SSCR1_TTELP		(1 << 31)	/* TXD Tristate Enable Last Phase */
+#define SSCR1_TTE		(1 << 30)	/* TXD Tristate Enable */
+#define SSCR1_EBCEI		(1 << 29)	/* Enable Bit Count Error interrupt */
+#define SSCR1_SCFR		(1 << 28)	/* Slave Clock free Running */
+#define SSCR1_ECRA		(1 << 27)	/* Enable Clock Request A */
+#define SSCR1_ECRB		(1 << 26)	/* Enable Clock request B */
+#define SSCR1_SCLKDIR		(1 << 25)	/* Serial Bit Rate Clock Direction */
+#define SSCR1_SFRMDIR		(1 << 24)	/* Frame Direction */
+#define SSCR1_RWOT		(1 << 23)	/* Receive Without Transmit */
+#define SSCR1_TRAIL		(1 << 22)	/* Trailing Byte */
+#define SSCR1_TSRE		(1 << 21)	/* Transmit Service Request Enable */
+#define SSCR1_RSRE		(1 << 20)	/* Receive Service Request Enable */
+#define SSCR1_TINTE		(1 << 19)	/* Receiver Time-out Interrupt enable */
+#define SSCR1_PINTE		(1 << 18)	/* Peripheral Trailing Byte Interupt Enable */
+#define SSCR1_IFS		(1 << 16)	/* Invert Frame Signal */
+#define SSCR1_STRF		(1 << 15)	/* Select FIFO or EFWR */
+#define SSCR1_EFWR		(1 << 14)	/* Enable FIFO Write/Read */
+
+#define SSSR_BCE		(1 << 23)	/* Bit Count Error */
+#define SSSR_CSS		(1 << 22)	/* Clock Synchronisation Status */
+#define SSSR_TUR		(1 << 21)	/* Transmit FIFO Under Run */
+#define SSSR_EOC		(1 << 20)	/* End Of Chain */
+#define SSSR_TINT		(1 << 19)	/* Receiver Time-out Interrupt */
+#define SSSR_PINT		(1 << 18)	/* Peripheral Trailing Byte Interrupt */
+
+#if defined(CONFIG_PXA3xx)
+#define SSPSP_EDMYSTOP(x)	((x) << 28)     /* Extended Dummy Stop */
+#define SSPSP_EDMYSTRT(x)	((x) << 26)     /* Extended Dummy Start */
+#endif
+
+#define SSPSP_FSRT		(1 << 25)	/* Frame Sync Relative Timing */
+#define SSPSP_DMYSTOP(x)	((x) << 23)	/* Dummy Stop */
+#define SSPSP_SFRMWDTH(x)	((x) << 16)	/* Serial Frame Width */
+#define SSPSP_SFRMDLY(x)	((x) << 9)	/* Serial Frame Delay */
+#define SSPSP_DMYSTRT(x)	((x) << 7)	/* Dummy Start */
+#define SSPSP_STRTDLY(x)	((x) << 4)	/* Start Delay */
+#define SSPSP_ETDS		(1 << 3)	/* End of Transfer data State */
+#define SSPSP_SFRMP		(1 << 2)	/* Serial Frame Polarity */
+#define SSPSP_SCMODE(x)		((x) << 0)	/* Serial Bit Rate Clock Mode */
+
+#define SSACD_SCDB		(1 << 3)	/* SSPSYSCLK Divider Bypass */
+#define SSACD_ACPS(x)		((x) << 4)	/* Audio clock PLL select */
+#define SSACD_ACDS(x)		((x) << 0)	/* Audio clock divider select */
+#if defined(CONFIG_PXA3xx)
+#define SSACD_SCDX8		(1 << 7)	/* SYSCLK division ratio select */
+#endif
+
+enum pxa_ssp_type {
+	SSP_UNDEFINED = 0,
+	PXA25x_SSP,  /* pxa 210, 250, 255, 26x */
+	PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
+	PXA27x_SSP,
+};
+
+struct ssp_device {
+	struct platform_device *pdev;
+	struct list_head	node;
+
+	struct clk	*clk;
+	void __iomem	*mmio_base;
+	unsigned long	phys_base;
+
+	const char	*label;
+	int		port_id;
+	int		type;
+	int		use_count;
+	int		irq;
+	int		drcmr_rx;
+	int		drcmr_tx;
+};
+
+/**
+ * ssp_write_reg - Write to a SSP register
+ *
+ * @dev: SSP device to access
+ * @reg: Register to write to
+ * @val: Value to be written.
+ */
+static inline void ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val)
+{
+	__raw_writel(val, dev->mmio_base + reg);
+}
+
+/**
+ * ssp_read_reg - Read from a SSP register
+ *
+ * @dev: SSP device to access
+ * @reg: Register to read from
+ */
+static inline u32 ssp_read_reg(struct ssp_device *dev, u32 reg)
+{
+	return __raw_readl(dev->mmio_base + reg);
+}
+
+struct ssp_device *ssp_request(int port, const char *label);
+void ssp_free(struct ssp_device *);
+#endif /* __ASM_ARCH_SSP_H */
diff --git a/arch/arm/plat-pxa/ssp.c b/arch/arm/plat-pxa/ssp.c
new file mode 100644
index 0000000..5fe2301
--- /dev/null
+++ b/arch/arm/plat-pxa/ssp.c
@@ -0,0 +1,223 @@
+/*
+ *  linux/arch/arm/mach-pxa/ssp.c
+ *
+ *  based on linux/arch/arm/mach-sa1100/ssp.c by Russell King
+ *
+ *  Copyright (C) 2003 Russell King.
+ *  Copyright (C) 2003 Wolfson Microelectronics PLC
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ *  PXA2xx SSP driver.  This provides the generic core for simple
+ *  IO-based SSP applications and allows easy port setup for DMA access.
+ *
+ *  Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+#include <asm/irq.h>
+#include <mach/hardware.h>
+#include <plat/ssp.h>
+
+static DEFINE_MUTEX(ssp_lock);
+static LIST_HEAD(ssp_list);
+
+struct ssp_device *ssp_request(int port, const char *label)
+{
+	struct ssp_device *ssp = NULL;
+
+	mutex_lock(&ssp_lock);
+
+	list_for_each_entry(ssp, &ssp_list, node) {
+		if (ssp->port_id == port && ssp->use_count == 0) {
+			ssp->use_count++;
+			ssp->label = label;
+			break;
+		}
+	}
+
+	mutex_unlock(&ssp_lock);
+
+	if (&ssp->node == &ssp_list)
+		return NULL;
+
+	return ssp;
+}
+EXPORT_SYMBOL(ssp_request);
+
+void ssp_free(struct ssp_device *ssp)
+{
+	mutex_lock(&ssp_lock);
+	if (ssp->use_count) {
+		ssp->use_count--;
+		ssp->label = NULL;
+	} else
+		dev_err(&ssp->pdev->dev, "device already free\n");
+	mutex_unlock(&ssp_lock);
+}
+EXPORT_SYMBOL(ssp_free);
+
+static int __devinit ssp_probe(struct platform_device *pdev)
+{
+	const struct platform_device_id *id = platform_get_device_id(pdev);
+	struct resource *res;
+	struct ssp_device *ssp;
+	int ret = 0;
+
+	ssp = kzalloc(sizeof(struct ssp_device), GFP_KERNEL);
+	if (ssp == NULL) {
+		dev_err(&pdev->dev, "failed to allocate memory");
+		return -ENOMEM;
+	}
+	ssp->pdev = pdev;
+
+	ssp->clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(ssp->clk)) {
+		ret = PTR_ERR(ssp->clk);
+		goto err_free;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res == NULL) {
+		dev_err(&pdev->dev, "no memory resource defined\n");
+		ret = -ENODEV;
+		goto err_free_clk;
+	}
+
+	res = request_mem_region(res->start, res->end - res->start + 1,
+			pdev->name);
+	if (res == NULL) {
+		dev_err(&pdev->dev, "failed to request memory resource\n");
+		ret = -EBUSY;
+		goto err_free_clk;
+	}
+
+	ssp->phys_base = res->start;
+
+	ssp->mmio_base = ioremap(res->start, res->end - res->start + 1);
+	if (ssp->mmio_base == NULL) {
+		dev_err(&pdev->dev, "failed to ioremap() registers\n");
+		ret = -ENODEV;
+		goto err_free_mem;
+	}
+
+	ssp->irq = platform_get_irq(pdev, 0);
+	if (ssp->irq < 0) {
+		dev_err(&pdev->dev, "no IRQ resource defined\n");
+		ret = -ENODEV;
+		goto err_free_io;
+	}
+
+	res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+	if (res == NULL) {
+		dev_err(&pdev->dev, "no SSP RX DRCMR defined\n");
+		ret = -ENODEV;
+		goto err_free_io;
+	}
+	ssp->drcmr_rx = res->start;
+
+	res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
+	if (res == NULL) {
+		dev_err(&pdev->dev, "no SSP TX DRCMR defined\n");
+		ret = -ENODEV;
+		goto err_free_io;
+	}
+	ssp->drcmr_tx = res->start;
+
+	/* PXA2xx/3xx SSP ports starts from 1 and the internal pdev->id
+	 * starts from 0, do a translation here
+	 */
+	ssp->port_id = pdev->id + 1;
+	ssp->use_count = 0;
+	ssp->type = (int)id->driver_data;
+
+	mutex_lock(&ssp_lock);
+	list_add(&ssp->node, &ssp_list);
+	mutex_unlock(&ssp_lock);
+
+	platform_set_drvdata(pdev, ssp);
+	return 0;
+
+err_free_io:
+	iounmap(ssp->mmio_base);
+err_free_mem:
+	release_mem_region(res->start, res->end - res->start + 1);
+err_free_clk:
+	clk_put(ssp->clk);
+err_free:
+	kfree(ssp);
+	return ret;
+}
+
+static int __devexit ssp_remove(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct ssp_device *ssp;
+
+	ssp = platform_get_drvdata(pdev);
+	if (ssp == NULL)
+		return -ENODEV;
+
+	iounmap(ssp->mmio_base);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	release_mem_region(res->start, res->end - res->start + 1);
+
+	clk_put(ssp->clk);
+
+	mutex_lock(&ssp_lock);
+	list_del(&ssp->node);
+	mutex_unlock(&ssp_lock);
+
+	kfree(ssp);
+	return 0;
+}
+
+static const struct platform_device_id ssp_id_table[] = {
+	{ "pxa25x-ssp",		PXA25x_SSP },
+	{ "pxa25x-nssp",	PXA25x_NSSP },
+	{ "pxa27x-ssp",		PXA27x_SSP },
+	{ },
+};
+
+static struct platform_driver ssp_driver = {
+	.probe		= ssp_probe,
+	.remove		= __devexit_p(ssp_remove),
+	.driver		= {
+		.owner	= THIS_MODULE,
+		.name	= "pxa2xx-ssp",
+	},
+	.id_table	= ssp_id_table,
+};
+
+static int __init pxa_ssp_init(void)
+{
+	return platform_driver_register(&ssp_driver);
+}
+
+static void __exit pxa_ssp_exit(void)
+{
+	platform_driver_unregister(&ssp_driver);
+}
+
+arch_initcall(pxa_ssp_init);
+module_exit(pxa_ssp_exit);
+
+MODULE_DESCRIPTION("PXA SSP driver");
+MODULE_AUTHOR("Liam Girdwood");
+MODULE_LICENSE("GPL");