Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "This merge window brings a good size of cleanups on various platforms.
  Among the bigger ones:

   - Removal of Samsung s5pc100 and s5p64xx platforms.  Both of these
     have lacked active support for quite a while, and after asking
     around nobody showed interest in keeping them around.  If needed,
     they could be resurrected in the future but it's more likely that
     we would prefer reintroduction of them as DT and
     multiplatform-enabled platforms instead.

   - OMAP4 controller code register define diet.  They defined a lot of
     registers that were never actually used, etc.

   - Move of some of the Tegra platform code (PMC, APBIO, fuse,
     powergate) to drivers/soc so it can be shared with 64-bit code.
     This also converts them over to traditional driver models where
     possible.

   - Removal of legacy gpio-samsung driver, since the last users have
     been removed (moved to pinctrl)

  Plus a bunch of smaller changes for various platforms that sort of
  dissapear in the diffstat for the above.  clps711x cleanups, shmobile
  header file refactoring/moves for multiplatform friendliness, some
  misc cleanups, etc"

* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
  drivers: CCI: Correct use of ! and &
  video: clcd-versatile: Depend on ARM
  video: fix up versatile CLCD helper move
  MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
  ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
  MAINTAINERS: Remove Kirkwood
  ARM: tegra: Convert PMC to a driver
  soc/tegra: fuse: Set up in early initcall
  ARM: tegra: Always lock the CPU reset vector
  ARM: tegra: Setup CPU hotplug in a pure initcall
  soc/tegra: Implement runtime check for Tegra SoCs
  soc/tegra: fuse: fix dummy functions
  soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
  soc/tegra: Add efuse and apbmisc bindings
  soc/tegra: Add efuse driver for Tegra
  ARM: tegra: move fuse exports to soc/tegra/fuse.h
  ARM: tegra: export apb dma readl/writel
  ARM: tegra: Use a function to get the chip ID
  ARM: tegra: Sort includes alphabetically
  ARM: tegra: Move includes to include/soc/tegra
  ...

1 files changed, 0 insertions, 39 deletions

diff --git a/arch/arm/mach-s5pc100/include/mach/debug-macro.S b/arch/arm/mach-s5pc100/include/mach/debug-macro.S
deleted file mode 100644
index 22c2385..0000000
--- a/arch/arm/mach-s5pc100/include/mach/debug-macro.S
+++ /dev/null
@@ -1,39 +0,0 @@
-/* arch/arm/mach-s5pc100/include/mach/debug-macro.S
- *
- * Copyright 2009 Samsung Electronics Co.
- *	Byungho Min <bhmin@samsung.com>
- *
- *
- * Based on mach-s3c6400/include/mach/debug-macro.S
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-/* pull in the relevant register and map files. */
-
-#include <linux/serial_s3c.h>
-#include <mach/map.h>
-
-	/* note, for the boot process to work we have to keep the UART
-	 * virtual address aligned to an 1MiB boundary for the L1
-	 * mapping the head code makes. We keep the UART virtual address
-	 * aligned and add in the offset when we load the value here.
-	 */
-
-	.macro addruart, rp, rv, tmp
-		ldr	\rp, = S3C_PA_UART
-		ldr	\rv, = S3C_VA_UART
-#if CONFIG_DEBUG_S3C_UART != 0
-		add	\rp, \rp, #(0x400 * CONFIG_DEBUG_S3C_UART)
-		add	\rv, \rv, #(0x400 * CONFIG_DEBUG_S3C_UART)
-#endif
-	.endm
-
-/* include the reset of the code which will do the work, we're only
- * compiling for a single cpu processor type so the default of s3c2440
- * will be fine with us.
- */
-
-#include <debug/samsung.S>