Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Olof Johansson:
 "Most of this branch consists of updates, additions and general churn
  of the device tree source files in the kernel (arch/arm/boot/dts).
  Besides that, there are a few things to point out:

   - Lots of platform conversion on OMAP2+, with removal of old board
     files for various platforms.
   - Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
     well
   - Some updates to pinctrl and other subsystems.  Most of these are
     for DT-enablement of the various platforms and acks have been
     collected"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
  ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
  ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
  ARM: dts: bcm281xx: Add card detect GPIO
  ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
  ARM: bcm281xx: Add device node for the GPIO controller
  ARM: mvebu: Add Netgear ReadyNAS 104 board
  ARM: tegra: fix Tegra114 IOMMU register address
  ARM: kirkwood: add support for OpenBlocks A7 platform
  ARM: dts: omap4-panda: add DPI pinmuxing
  ARM: dts: AM33xx: Add RNG node
  ARM: dts: AM33XX: Add hwspinlock node
  ARM: dts: OMAP5: Add hwspinlock node
  ARM: dts: OMAP4: Add hwspinlock node
  ARM: dts: use 'status' property for PCIe nodes
  ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
  ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
  ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
  ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
  ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
  ARM: mvebu: Add the core-divider clock to Armada 370/XP
  ...

26 files changed, 338 insertions, 2753 deletions

diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index c946244..dc21df1 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -87,6 +87,7 @@ config ARCH_OMAP2PLUS
 	select COMMON_CLK
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
+	select MACH_OMAP_GENERIC
 	select OMAP_DM_TIMER
 	select PINCTRL
 	select PROC_DEVICETREE if PROC_FS
@@ -180,16 +181,11 @@ config OMAP_PACKAGE_CUS
 config OMAP_PACKAGE_CBP
        bool
 
-comment "OMAP Board Type"
+comment "OMAP Legacy Platform Data Board Type"
 	depends on ARCH_OMAP2PLUS
 
 config MACH_OMAP_GENERIC
-	bool "Generic OMAP2+ board"
-	depends on ARCH_OMAP2PLUS
-	default y
-	help
-	  Support for generic TI OMAP2+ boards using Flattened Device Tree.
-	  More information at Documentation/devicetree
+	bool
 
 config MACH_OMAP2_TUSB6010
 	bool
@@ -253,12 +249,6 @@ config MACH_OVERO
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_OMAP3EVM
-	bool "OMAP 3530 EVM board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
 config MACH_OMAP3517EVM
 	bool "OMAP3517/ AM3517 EVM board"
 	depends on ARCH_OMAP3
@@ -307,33 +297,12 @@ config MACH_NOKIA_N8X0
 	select MACH_NOKIA_N810_WIMAX
 	select OMAP_PACKAGE_ZAC
 
-config MACH_NOKIA_RM680
-	bool "Nokia N950 (RM-680) / N9 (RM-696) phones"
-	depends on ARCH_OMAP3
-	default y
-	select MACH_NOKIA_RM696
-	select OMAP_PACKAGE_CBB
-
 config MACH_NOKIA_RX51
 	bool "Nokia N900 (RX-51) phone"
 	depends on ARCH_OMAP3
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_OMAP_ZOOM2
-	bool "OMAP3 Zoom2 board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-
-config MACH_OMAP_ZOOM3
-	bool "OMAP3630 Zoom3 board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBP
-	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-
 config MACH_CM_T35
 	bool "CompuLab CM-T35/CM-T3730 modules"
 	depends on ARCH_OMAP3
@@ -350,31 +319,12 @@ config MACH_CM_T3517
 config MACH_CM_T3730
        bool
 
-config MACH_IGEP0020
-	bool "IGEP v2 board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-
-config MACH_IGEP0030
-	bool "IGEP OMAP3 module"
-	depends on ARCH_OMAP3
-	default y
-	select MACH_IGEP0020
-	select OMAP_PACKAGE_CBB
-
 config MACH_SBC3530
 	bool "OMAP3 SBC STALKER board"
 	depends on ARCH_OMAP3
 	default y
 	select OMAP_PACKAGE_CUS
 
-config MACH_OMAP_3630SDP
-	bool "OMAP3630 SDP board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBP
-
 config MACH_TI8168EVM
 	bool "TI8168 Evaluation Module"
 	depends on SOC_TI81XX
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 9b7619f..e15ac00 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -236,7 +236,7 @@ endif
 obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 
 # Specific board support
-obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
+obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
 obj-$(CONFIG_MACH_OMAP3_BEAGLE)		+= board-omap3beagle.o
@@ -245,26 +245,14 @@ obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
 obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
 obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
 obj-$(CONFIG_MACH_OVERO)		+= board-overo.o
-obj-$(CONFIG_MACH_OMAP3EVM)		+= board-omap3evm.o
 obj-$(CONFIG_MACH_OMAP3_PANDORA)	+= board-omap3pandora.o
 obj-$(CONFIG_MACH_OMAP_3430SDP)		+= board-3430sdp.o
 obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o
-obj-$(CONFIG_MACH_NOKIA_RM680)		+= board-rm680.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-video.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2)		+= board-zoom.o board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2)		+= board-zoom-display.o
-obj-$(CONFIG_MACH_OMAP_ZOOM2)		+= board-zoom-debugboard.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3)		+= board-zoom.o board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3)		+= board-zoom-display.o
-obj-$(CONFIG_MACH_OMAP_ZOOM3)		+= board-zoom-debugboard.o
-obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-3630sdp.o
-obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-zoom-peripherals.o
-obj-$(CONFIG_MACH_OMAP_3630SDP)		+= board-zoom-display.o
 obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o
 obj-$(CONFIG_MACH_CM_T3517)		+= board-cm-t3517.o
-obj-$(CONFIG_MACH_IGEP0020)		+= board-igep0020.o
 obj-$(CONFIG_MACH_TOUCHBOOK)		+= board-omap3touchbook.o
 
 obj-$(CONFIG_MACH_OMAP3517EVM)		+= board-am3517evm.o
diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c
deleted file mode 100644
index 20d6d81..0000000
--- a/arch/arm/mach-omap2/board-3630sdp.c
+++ /dev/null
@@ -1,225 +0,0 @@
-/*
- * Copyright (C) 2009 Texas Instruments Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/mtd/nand.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-#include "gpmc-smc91x.h"
-
-#include "board-zoom.h"
-
-#include "board-flash.h"
-#include "mux.h"
-#include "sdram-hynix-h8mbx00u0mer-0em.h"
-
-#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
-
-static struct omap_smc91x_platform_data board_smc91x_data = {
-	.cs             = 3,
-	.flags          = GPMC_MUX_ADD_DATA | IORESOURCE_IRQ_LOWLEVEL,
-};
-
-static void __init board_smc91x_init(void)
-{
-	board_smc91x_data.gpio_irq = 158;
-	gpmc_smc91x_init(&board_smc91x_data);
-}
-
-#else
-
-static inline void board_smc91x_init(void)
-{
-}
-
-#endif /* defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE) */
-
-static void enable_board_wakeup_source(void)
-{
-	/* T2 interrupt line (keypad) */
-	omap_mux_init_signal("sys_nirq",
-		OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
-}
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 1,
-		.reset_gpio = 126,
-		.vcc_gpio = -EINVAL,
-	},
-	{
-		.port = 2,
-		.reset_gpio = 61,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-/*
- * SDP3630 CS organization
- * See also the Switch S8 settings in the comments.
- */
-static char chip_sel_sdp[][GPMC_CS_NUM] = {
-	{PDC_NOR, PDC_NAND, PDC_ONENAND, DBG_MPDB, 0, 0, 0, 0}, /* S8:1111 */
-	{PDC_ONENAND, PDC_NAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1110 */
-	{PDC_NAND, PDC_ONENAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1101 */
-};
-
-static struct mtd_partition sdp_nor_partitions[] = {
-	/* bootloader (U-Boot, etc) in first sector */
-	{
-		.name		= "Bootloader-NOR",
-		.offset		= 0,
-		.size		= SZ_256K,
-		.mask_flags	= MTD_WRITEABLE, /* force read-only */
-	},
-	/* bootloader params in the next sector */
-	{
-		.name		= "Params-NOR",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_256K,
-		.mask_flags	= 0,
-	},
-	/* kernel */
-	{
-		.name		= "Kernel-NOR",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_2M,
-		.mask_flags	= 0
-	},
-	/* file system */
-	{
-		.name		= "Filesystem-NOR",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= 0
-	}
-};
-
-static struct mtd_partition sdp_onenand_partitions[] = {
-	{
-		.name		= "X-Loader-OneNAND",
-		.offset		= 0,
-		.size		= 4 * (64 * 2048),
-		.mask_flags	= MTD_WRITEABLE  /* force read-only */
-	},
-	{
-		.name		= "U-Boot-OneNAND",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 2 * (64 * 2048),
-		.mask_flags	= MTD_WRITEABLE  /* force read-only */
-	},
-	{
-		.name		= "U-Boot Environment-OneNAND",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 1 * (64 * 2048),
-	},
-	{
-		.name		= "Kernel-OneNAND",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 16 * (64 * 2048),
-	},
-	{
-		.name		= "File System-OneNAND",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct mtd_partition sdp_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader-NAND",
-		.offset		= 0,
-		.size		= 4 * (64 * 2048),
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot-NAND",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 10 * (64 * 2048),
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "Boot Env-NAND",
-
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x1c0000 */
-		.size		= 6 * (64 * 2048),
-	},
-	{
-		.name		= "Kernel-NAND",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
-		.size		= 40 * (64 * 2048),
-	},
-	{
-		.name		= "File System - NAND",
-		.size		= MTDPART_SIZ_FULL,
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x780000 */
-	},
-};
-
-static struct flash_partitions sdp_flash_partitions[] = {
-	{
-		.parts = sdp_nor_partitions,
-		.nr_parts = ARRAY_SIZE(sdp_nor_partitions),
-	},
-	{
-		.parts = sdp_onenand_partitions,
-		.nr_parts = ARRAY_SIZE(sdp_onenand_partitions),
-	},
-	{
-		.parts = sdp_nand_partitions,
-		.nr_parts = ARRAY_SIZE(sdp_nand_partitions),
-	},
-};
-
-static void __init omap_sdp_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
-	zoom_peripherals_init();
-	omap_sdrc_init(h8mbx00u0mer0em_sdrc_params,
-				  h8mbx00u0mer0em_sdrc_params);
-	zoom_display_init();
-	board_smc91x_init();
-	board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16);
-	enable_board_wakeup_source();
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-}
-
-MACHINE_START(OMAP_3630SDP, "OMAP 3630SDP board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3630_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= omap_sdp_init,
-	.init_late	= omap3630_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index 87162e1..19f1652 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -15,13 +15,10 @@
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/irqdomain.h>
-#include <linux/clk.h>
 
 #include <asm/mach/arch.h>
 
 #include "common.h"
-#include "common-board-devices.h"
-#include "dss-common.h"
 
 #if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3))
 #define intc_of_init	NULL
@@ -36,40 +33,9 @@ static struct of_device_id omap_dt_match_table[] __initdata = {
 	{ }
 };
 
-/*
- * Create alias for USB host PHY clock.
- * Remove this when clock phandle can be provided via DT
- */
-static void __init legacy_init_ehci_clk(char *clkname)
-{
-	int ret;
-
-	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
-	if (ret) {
-		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
-						__func__, clkname, ret);
-	}
-}
-
 static void __init omap_generic_init(void)
 {
-	omap_sdrc_init(NULL, NULL);
-
-	of_platform_populate(NULL, omap_dt_match_table, NULL, NULL);
-
-	/*
-	 * HACK: call display setup code for selected boards to enable omapdss.
-	 * This will be removed when omapdss supports DT.
-	 */
-	if (of_machine_is_compatible("ti,omap4-panda")) {
-		omap4_panda_display_init_of();
-		legacy_init_ehci_clk("auxclk3_ck");
-
-	}
-	else if (of_machine_is_compatible("ti,omap4-sdp"))
-		omap_4430sdp_display_init_of();
-	else if (of_machine_is_compatible("ti,omap5-uevm"))
-		legacy_init_ehci_clk("auxclk1_ck");
+	pdata_quirks_init(omap_dt_match_table);
 }
 
 #ifdef CONFIG_SOC_OMAP2420
@@ -180,6 +146,7 @@ DT_MACHINE_START(AM33XX_DT, "Generic AM33XX (Flattened Device Tree)")
 	.init_irq	= omap_intc_of_init,
 	.handle_irq	= omap3_intc_handle_irq,
 	.init_machine	= omap_generic_init,
+	.init_late	= am33xx_init_late,
 	.init_time	= omap3_gptimer_timer_init,
 	.dt_compat	= am33xx_boards_compat,
 	.restart	= am33xx_restart,
@@ -219,6 +186,7 @@ DT_MACHINE_START(OMAP5_DT, "Generic OMAP5 (Flattened Device Tree)")
 	.init_early	= omap5_init_early,
 	.init_irq	= omap_gic_of_init,
 	.init_machine	= omap_generic_init,
+	.init_late	= omap5_init_late,
 	.init_time	= omap5_realtime_timer_init,
 	.dt_compat	= omap5_boards_compat,
 	.restart	= omap44xx_restart,
@@ -234,6 +202,7 @@ static const char *am43_boards_compat[] __initdata = {
 DT_MACHINE_START(AM43_DT, "Generic AM43 (Flattened Device Tree)")
 	.map_io		= am33xx_map_io,
 	.init_early	= am43xx_init_early,
+	.init_late	= am43xx_init_late,
 	.init_irq	= omap_gic_of_init,
 	.init_machine	= omap_generic_init,
 	.init_time	= omap3_sync32k_timer_init,
@@ -252,6 +221,7 @@ DT_MACHINE_START(DRA7XX_DT, "Generic DRA7XX (Flattened Device Tree)")
 	.smp		= smp_ops(omap4_smp_ops),
 	.map_io		= omap5_map_io,
 	.init_early	= dra7xx_init_early,
+	.init_late	= dra7xx_init_late,
 	.init_irq	= omap_gic_of_init,
 	.init_machine	= omap_generic_init,
 	.init_time	= omap5_realtime_timer_init,
diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c
deleted file mode 100644
index 06dbb2d..0000000
--- a/arch/arm/mach-omap2/board-igep0020.c
+++ /dev/null
@@ -1,718 +0,0 @@
-/*
- * Copyright (C) 2009 Integration Software and Electronic Engineering.
- *
- * Modified from mach-omap2/board-generic.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-#include <linux/input.h>
-#include <linux/usb/phy.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-
-#include <linux/mtd/nand.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/mtd-onenand-omap2.h>
-
-#include "common.h"
-#include "gpmc.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "sdram-numonyx-m65kxxxxam.h"
-#include "common-board-devices.h"
-#include "board-flash.h"
-#include "control.h"
-#include "gpmc-onenand.h"
-
-#define IGEP2_SMSC911X_CS       5
-#define IGEP2_SMSC911X_GPIO     176
-#define IGEP2_GPIO_USBH_NRESET  24
-#define IGEP2_GPIO_LED0_GREEN   26
-#define IGEP2_GPIO_LED0_RED     27
-#define IGEP2_GPIO_LED1_RED     28
-#define IGEP2_GPIO_DVI_PUP      170
-
-#define IGEP2_RB_GPIO_WIFI_NPD     94
-#define IGEP2_RB_GPIO_WIFI_NRESET  95
-#define IGEP2_RB_GPIO_BT_NRESET    137
-#define IGEP2_RC_GPIO_WIFI_NPD     138
-#define IGEP2_RC_GPIO_WIFI_NRESET  139
-#define IGEP2_RC_GPIO_BT_NRESET    137
-
-#define IGEP3_GPIO_LED0_GREEN	54
-#define IGEP3_GPIO_LED0_RED	53
-#define IGEP3_GPIO_LED1_RED	16
-#define IGEP3_GPIO_USBH_NRESET  183
-
-#define IGEP_SYSBOOT_MASK           0x1f
-#define IGEP_SYSBOOT_NAND           0x0f
-#define IGEP_SYSBOOT_ONENAND        0x10
-
-/*
- * IGEP2 Hardware Revision Table
- *
- *  --------------------------------------------------------------------------
- * | Id. | Hw Rev.            | HW0 (28) | WIFI_NPD | WIFI_NRESET | BT_NRESET |
- *  --------------------------------------------------------------------------
- * |  0  | B                  |   high   |  gpio94  |   gpio95    |     -     |
- * |  0  | B/C (B-compatible) |   high   |  gpio94  |   gpio95    |  gpio137  |
- * |  1  | C                  |   low    |  gpio138 |   gpio139   |  gpio137  |
- *  --------------------------------------------------------------------------
- */
-
-#define IGEP2_BOARD_HWREV_B	0
-#define IGEP2_BOARD_HWREV_C	1
-#define IGEP3_BOARD_HWREV	2
-
-static u8 hwrev;
-
-static void __init igep2_get_revision(void)
-{
-	u8 ret;
-
-	if (machine_is_igep0030()) {
-		hwrev = IGEP3_BOARD_HWREV;
-		return;
-	}
-
-	omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT);
-
-	if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) {
-		pr_warning("IGEP2: Could not obtain gpio GPIO_HW0_REV\n");
-		pr_err("IGEP2: Unknown Hardware Revision\n");
-		return;
-	}
-
-	ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
-	if (ret == 0) {
-		pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
-		hwrev = IGEP2_BOARD_HWREV_C;
-	} else if (ret ==  1) {
-		pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
-		hwrev = IGEP2_BOARD_HWREV_B;
-	} else {
-		pr_err("IGEP2: Unknown Hardware Revision\n");
-		hwrev = -1;
-	}
-
-	gpio_free(IGEP2_GPIO_LED1_RED);
-}
-
-#if defined(CONFIG_MTD_ONENAND_OMAP2) ||		\
-	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) ||	\
-	defined(CONFIG_MTD_NAND_OMAP2) ||		\
-	defined(CONFIG_MTD_NAND_OMAP2_MODULE)
-
-#define ONENAND_MAP             0x20000000
-
-/* NAND04GR4E1A ( x2 Flash built-in COMBO POP MEMORY )
- * Since the device is equipped with two DataRAMs, and two-plane NAND
- * Flash memory array, these two component enables simultaneous program
- * of 4KiB. Plane1 has only even blocks such as block0, block2, block4
- * while Plane2 has only odd blocks such as block1, block3, block5.
- * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
- */
-
-static struct mtd_partition igep_flash_partitions[] = {
-	{
-		.name           = "X-Loader",
-		.offset         = 0,
-		.size           = 2 * (64*(2*2048))
-	},
-	{
-		.name           = "U-Boot",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 6 * (64*(2*2048)),
-	},
-	{
-		.name           = "Environment",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 2 * (64*(2*2048)),
-	},
-	{
-		.name           = "Kernel",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 12 * (64*(2*2048)),
-	},
-	{
-		.name           = "File System",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = MTDPART_SIZ_FULL,
-	},
-};
-
-static inline u32 igep_get_sysboot_value(void)
-{
-	return omap_ctrl_readl(OMAP343X_CONTROL_STATUS) & IGEP_SYSBOOT_MASK;
-}
-
-static void __init igep_flash_init(void)
-{
-	u32 mux;
-	mux = igep_get_sysboot_value();
-
-	if (mux == IGEP_SYSBOOT_NAND) {
-		pr_info("IGEP: initializing NAND memory device\n");
-		board_nand_init(igep_flash_partitions,
-				ARRAY_SIZE(igep_flash_partitions),
-				0, NAND_BUSWIDTH_16, nand_default_timings);
-	} else if (mux == IGEP_SYSBOOT_ONENAND) {
-		pr_info("IGEP: initializing OneNAND memory device\n");
-		board_onenand_init(igep_flash_partitions,
-				   ARRAY_SIZE(igep_flash_partitions), 0);
-	} else {
-		pr_err("IGEP: Flash: unsupported sysboot sequence found\n");
-	}
-}
-
-#else
-static void __init igep_flash_init(void) {}
-#endif
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-
-#include <linux/smsc911x.h>
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
-	.cs             = IGEP2_SMSC911X_CS,
-	.gpio_irq       = IGEP2_SMSC911X_GPIO,
-	.gpio_reset     = -EINVAL,
-	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static inline void __init igep2_init_smsc911x(void)
-{
-	gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init igep2_init_smsc911x(void) { }
-#endif
-
-static struct regulator_consumer_supply igep_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data igep_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(igep_vmmc1_supply),
-	.consumer_supplies      = igep_vmmc1_supply,
-};
-
-static struct regulator_consumer_supply igep_vio_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1"),
-};
-
-static struct regulator_init_data igep_vio = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV		= 1,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(igep_vio_supply),
-	.consumer_supplies      = igep_vio_supply,
-};
-
-static struct regulator_consumer_supply igep_vmmc2_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-static struct regulator_init_data igep_vmmc2 = {
-	.constraints		= {
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL,
-		.always_on		= 1,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(igep_vmmc2_supply),
-	.consumer_supplies	= igep_vmmc2_supply,
-};
-
-static struct fixed_voltage_config igep_vwlan = {
-	.supply_name		= "vwlan",
-	.microvolts		= 3300000,
-	.gpio			= -EINVAL,
-	.enabled_at_boot	= 1,
-	.init_data		= &igep_vmmc2,
-};
-
-static struct platform_device igep_vwlan_device = {
-	.name		= "reg-fixed-voltage",
-	.id		= 0,
-	.dev = {
-		.platform_data	= &igep_vwlan,
-	},
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-		.deferred	= true,
-	},
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
-	{
-		.mmc		= 2,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-	},
-#endif
-	{}      /* Terminator */
-};
-
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led igep_gpio_leds[] = {
-	[0] = {
-		.name			= "omap3:red:user0",
-		.default_state		= 0,
-	},
-	[1] = {
-		.name			= "omap3:green:boot",
-		.default_state		= 1,
-	},
-	[2] = {
-		.name			= "omap3:red:user1",
-		.default_state		= 0,
-	},
-	[3] = {
-		.name			= "omap3:green:user1",
-		.default_state		= 0,
-		.gpio			= -EINVAL, /* gets replaced */
-		.active_low		= 1,
-	},
-};
-
-static struct gpio_led_platform_data igep_led_pdata = {
-	.leds           = igep_gpio_leds,
-	.num_leds       = ARRAY_SIZE(igep_gpio_leds),
-};
-
-static struct platform_device igep_led_device = {
-	 .name   = "leds-gpio",
-	 .id     = -1,
-	 .dev    = {
-		 .platform_data  =  &igep_led_pdata,
-	},
-};
-
-static void __init igep_leds_init(void)
-{
-	if (machine_is_igep0020()) {
-		igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
-		igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
-		igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
-	} else {
-		igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
-		igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
-		igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
-	}
-
-	platform_device_register(&igep_led_device);
-}
-
-#else
-static struct gpio igep_gpio_leds[] __initdata = {
-	{ -EINVAL,	GPIOF_OUT_INIT_LOW, "gpio-led:red:d0"   },
-	{ -EINVAL,	GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
-	{ -EINVAL,	GPIOF_OUT_INIT_LOW, "gpio-led:red:d1"   },
-};
-
-static inline void igep_leds_init(void)
-{
-	int i;
-
-	if (machine_is_igep0020()) {
-		igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
-		igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
-		igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
-	} else {
-		igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
-		igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
-		igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
-	}
-
-	if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) {
-		pr_warning("IGEP v2: Could not obtain leds gpios\n");
-		return;
-	}
-
-	for (i = 0; i < ARRAY_SIZE(igep_gpio_leds); i++)
-		gpio_export(igep_gpio_leds[i].gpio, 0);
-}
-#endif
-
-static struct gpio igep2_twl_gpios[] = {
-	{ -EINVAL, GPIOF_IN,		"GPIO_EHCI_NOC"  },
-	{ -EINVAL, GPIOF_OUT_INIT_LOW,	"GPIO_USBH_CPEN" },
-};
-
-static int igep_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	int ret;
-
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
-#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
-	ret = gpio_request_one(gpio + TWL4030_GPIO_MAX + 1, GPIOF_OUT_INIT_HIGH,
-			       "gpio-led:green:d1");
-	if (ret == 0)
-		gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
-	else
-		pr_warning("IGEP: Could not obtain gpio GPIO_LED1_GREEN\n");
-#else
-	igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
-#endif
-
-	if (machine_is_igep0030())
-		return 0;
-
-	/*
-	 * REVISIT: need ehci-omap hooks for external VBUS
-	 * power switch and overcurrent detect
-	 */
-	igep2_twl_gpios[0].gpio = gpio + 1;
-
-	/* TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN (out, active low) */
-	igep2_twl_gpios[1].gpio = gpio + TWL4030_GPIO_MAX;
-
-	ret = gpio_request_array(igep2_twl_gpios, ARRAY_SIZE(igep2_twl_gpios));
-	if (ret < 0)
-		pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
-
-	return 0;
-};
-
-static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = {
-	.use_leds	= true,
-	.setup		= igep_twl_gpio_setup,
-};
-
-static struct connector_dvi_platform_data omap3stalker_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = 3,
-};
-
-static struct platform_device omap3stalker_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3stalker_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = IGEP2_GPIO_DVI_PUP,
-};
-
-static struct platform_device omap3stalker_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &omap3stalker_tfp410_pdata,
-};
-
-static struct omap_dss_board_info igep2_dss_data = {
-	.default_display_name = "dvi",
-};
-
-static struct platform_device *igep_devices[] __initdata = {
-	&igep_vwlan_device,
-	&omap3stalker_tfp410_device,
-	&omap3stalker_dvi_connector_device,
-};
-
-static int igep2_keymap[] = {
-	KEY(0, 0, KEY_LEFT),
-	KEY(0, 1, KEY_RIGHT),
-	KEY(0, 2, KEY_A),
-	KEY(0, 3, KEY_B),
-	KEY(1, 0, KEY_DOWN),
-	KEY(1, 1, KEY_UP),
-	KEY(1, 2, KEY_E),
-	KEY(1, 3, KEY_F),
-	KEY(2, 0, KEY_ENTER),
-	KEY(2, 1, KEY_I),
-	KEY(2, 2, KEY_J),
-	KEY(2, 3, KEY_K),
-	KEY(3, 0, KEY_M),
-	KEY(3, 1, KEY_N),
-	KEY(3, 2, KEY_O),
-	KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data igep2_keymap_data = {
-	.keymap			= igep2_keymap,
-	.keymap_size		= ARRAY_SIZE(igep2_keymap),
-};
-
-static struct twl4030_keypad_data igep2_keypad_pdata = {
-	.keymap_data	= &igep2_keymap_data,
-	.rows		= 4,
-	.cols		= 4,
-	.rep		= 1,
-};
-
-static struct twl4030_platform_data igep_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &igep_twl4030_gpio_pdata,
-	.vmmc1          = &igep_vmmc1,
-	.vio		= &igep_vio,
-};
-
-static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
-	{
-		I2C_BOARD_INFO("eeprom", 0x50),
-	},
-};
-
-static void __init igep_i2c_init(void)
-{
-	int ret;
-
-	omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_USB,
-			      TWL_COMMON_REGULATOR_VPLL2);
-	igep_twldata.vpll2->constraints.apply_uV = true;
-	igep_twldata.vpll2->constraints.name = "VDVI";
-
-	if (machine_is_igep0020()) {
-		/*
-		 * Bus 3 is attached to the DVI port where devices like the
-		 * pico DLP projector don't work reliably with 400kHz
-		 */
-		ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
-					    ARRAY_SIZE(igep2_i2c3_boardinfo));
-		if (ret)
-			pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
-
-		igep_twldata.keypad	= &igep2_keypad_pdata;
-		/* Get common pmic data */
-		omap3_pmic_get_config(&igep_twldata, TWL_COMMON_PDATA_AUDIO, 0);
-	}
-
-	omap3_pmic_init("twl4030", &igep_twldata);
-}
-
-static struct usbhs_phy_data igep2_phy_data[] __initdata = {
-	{
-		.port = 1,
-		.reset_gpio = IGEP2_GPIO_USBH_NRESET,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct usbhs_phy_data igep3_phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = IGEP3_GPIO_USBH_NRESET,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = {
-	.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = {
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* Display Sub System */
-	OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	/* TFP410 PanelBus DVI Transmitte (GPIO_170) */
-	OMAP3_MUX(HDQ_SIO, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	/* SMSC9221 LAN Controller ETH IRQ (GPIO_176) */
-	OMAP3_MUX(MCSPI1_CS2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
-static struct gpio igep_wlan_bt_gpios[] __initdata = {
-	{ -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NPD"	   },
-	{ -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NRESET" },
-	{ -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_BT_NRESET"   },
-};
-
-static void __init igep_wlan_bt_init(void)
-{
-	int err;
-
-	/* GPIO's for WLAN-BT combo depends on hardware revision */
-	if (hwrev == IGEP2_BOARD_HWREV_B) {
-		igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
-		igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
-		igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
-	} else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) {
-		igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
-		igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
-		igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
-	} else
-		return;
-
-	/* Make sure that the GPIO pins are muxed correctly */
-	omap_mux_init_gpio(igep_wlan_bt_gpios[0].gpio, OMAP_PIN_OUTPUT);
-	omap_mux_init_gpio(igep_wlan_bt_gpios[1].gpio, OMAP_PIN_OUTPUT);
-	omap_mux_init_gpio(igep_wlan_bt_gpios[2].gpio, OMAP_PIN_OUTPUT);
-
-	err = gpio_request_array(igep_wlan_bt_gpios,
-				 ARRAY_SIZE(igep_wlan_bt_gpios));
-	if (err) {
-		pr_warning("IGEP2: Could not obtain WIFI/BT gpios\n");
-		return;
-	}
-
-	gpio_export(igep_wlan_bt_gpios[0].gpio, 0);
-	gpio_export(igep_wlan_bt_gpios[1].gpio, 0);
-	gpio_export(igep_wlan_bt_gpios[2].gpio, 0);
-
-	gpio_set_value(igep_wlan_bt_gpios[1].gpio, 0);
-	udelay(10);
-	gpio_set_value(igep_wlan_bt_gpios[1].gpio, 1);
-
-}
-#else
-static inline void __init igep_wlan_bt_init(void) { }
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init igep_init(void)
-{
-	regulator_register_fixed(1, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
-	/* Get IGEP2 hardware revision */
-	igep2_get_revision();
-
-	omap_hsmmc_init(mmc);
-
-	/* Register I2C busses and drivers */
-	igep_i2c_init();
-	platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));
-	omap_serial_init();
-	omap_sdrc_init(m65kxxxxam_sdrc_params,
-				  m65kxxxxam_sdrc_params);
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	igep_flash_init();
-	igep_leds_init();
-	omap_twl4030_audio_init("igep2", NULL);
-
-	/*
-	 * WLAN-BT combo module from MuRata which has a Marvell WLAN
-	 * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
-	 */
-	igep_wlan_bt_init();
-
-	if (machine_is_igep0020()) {
-		omap_display_init(&igep2_dss_data);
-		igep2_init_smsc911x();
-		usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data));
-		usbhs_init(&igep2_usbhs_bdata);
-	} else {
-		usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data));
-		usbhs_init(&igep3_usbhs_bdata);
-	}
-}
-
-MACHINE_START(IGEP0020, "IGEP v2 board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= igep_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(IGEP0030, "IGEP OMAP3 module")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= igep_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c
index dd8da2c..4ec8d82 100644
--- a/arch/arm/mach-omap2/board-ldp.c
+++ b/arch/arm/mach-omap2/board-ldp.c
@@ -36,7 +36,6 @@
 #include <asm/mach/map.h>
 
 #include "common.h"
-#include "board-zoom.h"
 #include "gpmc.h"
 #include "gpmc-smsc911x.h"
 
@@ -406,7 +405,7 @@ static void __init omap_ldp_init(void)
 	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 	usb_musb_init(NULL);
 	board_nand_init(ldp_nand_partitions, ARRAY_SIZE(ldp_nand_partitions),
-			ZOOM_NAND_CS, 0, nand_default_timings);
+			0, 0, nand_default_timings);
 
 	omap_hsmmc_init(mmc);
 	ldp_display_init();
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
deleted file mode 100644
index 1814387..0000000
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ /dev/null
@@ -1,756 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3evm.c
- *
- * Copyright (C) 2008 Texas Instruments
- *
- * Modified from mach-omap2/board-3430sdp.c
- *
- * Initial code: Syed Mohammed Khasim
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/gpio.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/leds.h>
-#include <linux/interrupt.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/i2c/twl.h>
-#include <linux/usb/otg.h>
-#include <linux/usb/musb.h>
-#include <linux/usb/usb_phy_gen_xceiv.h>
-#include <linux/smsc911x.h>
-
-#include <linux/wl12xx.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/mmc/host.h>
-#include <linux/export.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/platform_data/mtd-nand-omap2.h>
-#include "common.h"
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "soc.h"
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-#include "board-flash.h"
-
-#define	NAND_CS			0
-
-#define OMAP3_EVM_TS_GPIO	175
-#define OMAP3_EVM_EHCI_VBUS	22
-#define OMAP3_EVM_EHCI_SELECT	61
-
-#define OMAP3EVM_ETHR_START	0x2c000000
-#define OMAP3EVM_ETHR_SIZE	1024
-#define OMAP3EVM_ETHR_ID_REV	0x50
-#define OMAP3EVM_ETHR_GPIO_IRQ	176
-#define OMAP3EVM_SMSC911X_CS	5
-/*
- * Eth Reset signal
- *	64 = Generation 1 (<=RevD)
- *	7 = Generation 2 (>=RevE)
- */
-#define OMAP3EVM_GEN1_ETHR_GPIO_RST	64
-#define OMAP3EVM_GEN2_ETHR_GPIO_RST	7
-
-/*
- * OMAP35x EVM revision
- * Run time detection of EVM revision is done by reading Ethernet
- * PHY ID -
- *	GEN_1	= 0x01150000
- *	GEN_2	= 0x92200000
- */
-enum {
-	OMAP3EVM_BOARD_GEN_1 = 0,	/* EVM Rev between  A - D */
-	OMAP3EVM_BOARD_GEN_2,		/* EVM Rev >= Rev E */
-};
-
-static u8 omap3_evm_version;
-
-static u8 get_omap3_evm_rev(void)
-{
-	return omap3_evm_version;
-}
-
-static void __init omap3_evm_get_revision(void)
-{
-	void __iomem *ioaddr;
-	unsigned int smsc_id;
-
-	/* Ethernet PHY ID is stored at ID_REV register */
-	ioaddr = ioremap_nocache(OMAP3EVM_ETHR_START, SZ_1K);
-	if (!ioaddr)
-		return;
-	smsc_id = readl(ioaddr + OMAP3EVM_ETHR_ID_REV) & 0xFFFF0000;
-	iounmap(ioaddr);
-
-	switch (smsc_id) {
-	/*SMSC9115 chipset*/
-	case 0x01150000:
-		omap3_evm_version = OMAP3EVM_BOARD_GEN_1;
-		break;
-	/*SMSC 9220 chipset*/
-	case 0x92200000:
-	default:
-		omap3_evm_version = OMAP3EVM_BOARD_GEN_2;
-	}
-}
-
-#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-#include "gpmc-smsc911x.h"
-
-static struct omap_smsc911x_platform_data smsc911x_cfg = {
-	.cs             = OMAP3EVM_SMSC911X_CS,
-	.gpio_irq       = OMAP3EVM_ETHR_GPIO_IRQ,
-	.gpio_reset     = -EINVAL,
-	.flags		= SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
-};
-
-static inline void __init omap3evm_init_smsc911x(void)
-{
-	/* Configure ethernet controller reset gpio */
-	if (cpu_is_omap3430()) {
-		if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
-			smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST;
-		else
-			smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST;
-	}
-
-	gpmc_smsc911x_init(&smsc911x_cfg);
-}
-
-#else
-static inline void __init omap3evm_init_smsc911x(void) { return; }
-#endif
-
-/*
- * OMAP3EVM LCD Panel control signals
- */
-#define OMAP3EVM_LCD_PANEL_LR		2
-#define OMAP3EVM_LCD_PANEL_UD		3
-#define OMAP3EVM_LCD_PANEL_INI		152
-#define OMAP3EVM_LCD_PANEL_QVGA		154
-#define OMAP3EVM_LCD_PANEL_RESB		155
-
-#define OMAP3EVM_LCD_PANEL_ENVDD	153
-#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO	210
-
-/*
- * OMAP3EVM DVI control signals
- */
-#define OMAP3EVM_DVI_PANEL_EN_GPIO	199
-
-#ifdef CONFIG_BROKEN
-static void __init omap3_evm_display_init(void)
-{
-	int r;
-
-	r = gpio_request_one(OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW,
-				"lcd_panel_envdd");
-	if (r)
-		pr_err("failed to get lcd_panel_envdd GPIO\n");
-
-	r = gpio_request_one(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO,
-				GPIOF_OUT_INIT_LOW, "lcd_panel_bklight");
-	if (r)
-		pr_err("failed to get lcd_panel_bklight GPIO\n");
-
-	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
-		gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 0);
-	else
-		gpio_set_value_cansleep(OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO, 1);
-}
-#endif
-
-static struct panel_sharp_ls037v7dw01_platform_data omap3_evm_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 18,
-
-	.resb_gpio		= OMAP3EVM_LCD_PANEL_RESB,
-	.ini_gpio		= OMAP3EVM_LCD_PANEL_INI,
-	.mo_gpio		= OMAP3EVM_LCD_PANEL_QVGA,
-	.lr_gpio		= OMAP3EVM_LCD_PANEL_LR,
-	.ud_gpio		= OMAP3EVM_LCD_PANEL_UD,
-};
-
-static struct platform_device omap3_evm_lcd_device = {
-	.name                   = "panel-sharp-ls037v7dw01",
-	.id                     = 0,
-	.dev.platform_data      = &omap3_evm_lcd_pdata,
-};
-
-static struct connector_dvi_platform_data omap3_evm_dvi_connector_pdata = {
-	.name                   = "dvi",
-	.source                 = "tfp410.0",
-	.i2c_bus_num            = -1,
-};
-
-static struct platform_device omap3_evm_dvi_connector_device = {
-	.name                   = "connector-dvi",
-	.id                     = 0,
-	.dev.platform_data      = &omap3_evm_dvi_connector_pdata,
-};
-
-static struct encoder_tfp410_platform_data omap3_evm_tfp410_pdata = {
-	.name                   = "tfp410.0",
-	.source                 = "dpi.0",
-	.data_lines             = 24,
-	.power_down_gpio        = OMAP3EVM_DVI_PANEL_EN_GPIO,
-};
-
-static struct platform_device omap3_evm_tfp410_device = {
-	.name                   = "tfp410",
-	.id                     = 0,
-	.dev.platform_data      = &omap3_evm_tfp410_pdata,
-};
-
-static struct connector_atv_platform_data omap3_evm_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.invert_polarity = false,
-};
-
-static struct platform_device omap3_evm_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &omap3_evm_tv_pdata,
-};
-
-static struct omap_dss_board_info omap3_evm_dss_data = {
-	.default_display_name = "lcd",
-};
-
-static struct regulator_consumer_supply omap3evm_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply omap3evm_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3evm_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vmmc1_supply),
-	.consumer_supplies	= omap3evm_vmmc1_supply,
-};
-
-/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
-static struct regulator_init_data omap3evm_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vsim_supply),
-	.consumer_supplies	= omap3evm_vsim_supply,
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= 63,
-		.deferred	= true,
-	},
-#ifdef CONFIG_WILINK_PLATFORM_DATA
-	{
-		.name		= "wl1271",
-		.mmc		= 2,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
-		.gpio_wp	= -EINVAL,
-		.gpio_cd	= -EINVAL,
-		.nonremovable	= true,
-	},
-#endif
-	{}	/* Terminator */
-};
-
-static struct gpio_led gpio_leds[] = {
-	{
-		.name			= "omap3evm::ledb",
-		/* normally not visible (board underside) */
-		.default_trigger	= "default-on",
-		.gpio			= -EINVAL,	/* gets replaced */
-		.active_low		= true,
-	},
-};
-
-static struct gpio_led_platform_data gpio_led_info = {
-	.leds		= gpio_leds,
-	.num_leds	= ARRAY_SIZE(gpio_leds),
-};
-
-static struct platform_device leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &gpio_led_info,
-	},
-};
-
-
-static int omap3evm_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	int r, lcd_bl_en;
-
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/*
-	 * Most GPIOs are for USB OTG.  Some are mostly sent to
-	 * the P2 connector; notably LEDA for the LCD backlight.
-	 */
-
-	/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
-	lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ?
-		GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
-	r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL");
-	if (r)
-		printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
-
-	/* gpio + 7 == DVI Enable */
-	gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
-
-	/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
-	gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
-	platform_device_register(&leds_gpio);
-
-	/* Enable VBUS switch by setting TWL4030.GPIO2DIR as output
-	 * for starting USB tranceiver
-	 */
-#ifdef CONFIG_TWL4030_CORE
-	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
-		u8 val;
-
-		twl_i2c_read_u8(TWL4030_MODULE_GPIO, &val, REG_GPIODATADIR1);
-		val |= 0x04; /* TWL4030.GPIO2DIR BIT at GPIODATADIR1(0x9B) */
-		twl_i2c_write_u8(TWL4030_MODULE_GPIO, val, REG_GPIODATADIR1);
-	}
-#endif
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3evm_gpio_data = {
-	.use_leds	= true,
-	.setup		= omap3evm_twl_gpio_setup,
-};
-
-static uint32_t board_keymap[] = {
-	KEY(0, 0, KEY_LEFT),
-	KEY(0, 1, KEY_DOWN),
-	KEY(0, 2, KEY_ENTER),
-	KEY(0, 3, KEY_M),
-
-	KEY(1, 0, KEY_RIGHT),
-	KEY(1, 1, KEY_UP),
-	KEY(1, 2, KEY_I),
-	KEY(1, 3, KEY_N),
-
-	KEY(2, 0, KEY_A),
-	KEY(2, 1, KEY_E),
-	KEY(2, 2, KEY_J),
-	KEY(2, 3, KEY_O),
-
-	KEY(3, 0, KEY_B),
-	KEY(3, 1, KEY_F),
-	KEY(3, 2, KEY_K),
-	KEY(3, 3, KEY_P)
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap			= board_keymap,
-	.keymap_size		= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data omap3evm_kp_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 4,
-	.cols		= 4,
-	.rep		= 1,
-};
-
-/* ads7846 on SPI */
-static struct regulator_consumer_supply omap3evm_vio_supply[] = {
-	REGULATOR_SUPPLY("vcc", "spi1.0"),
-};
-
-/* VIO for ads7846 */
-static struct regulator_init_data omap3evm_vio = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vio_supply),
-	.consumer_supplies	= omap3evm_vio_supply,
-};
-
-#ifdef CONFIG_WILINK_PLATFORM_DATA
-
-#define OMAP3EVM_WLAN_PMENA_GPIO	(150)
-#define OMAP3EVM_WLAN_IRQ_GPIO		(149)
-
-static struct regulator_consumer_supply omap3evm_vmmc2_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-/* VMMC2 for driving the WL12xx module */
-static struct regulator_init_data omap3evm_vmmc2 = {
-	.constraints = {
-		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(omap3evm_vmmc2_supply),
-	.consumer_supplies	= omap3evm_vmmc2_supply,
-};
-
-static struct fixed_voltage_config omap3evm_vwlan = {
-	.supply_name		= "vwl1271",
-	.microvolts		= 1800000, /* 1.80V */
-	.gpio			= OMAP3EVM_WLAN_PMENA_GPIO,
-	.startup_delay		= 70000, /* 70ms */
-	.enable_high		= 1,
-	.enabled_at_boot	= 0,
-	.init_data		= &omap3evm_vmmc2,
-};
-
-static struct platform_device omap3evm_wlan_regulator = {
-	.name		= "reg-fixed-voltage",
-	.id		= 1,
-	.dev = {
-		.platform_data	= &omap3evm_vwlan,
-	},
-};
-
-struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
-	.board_ref_clock = WL12XX_REFCLOCK_38, /* 38.4 MHz */
-};
-#endif
-
-/* VAUX2 for USB */
-static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
-	REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"),	/* OMAP ISP */
-	REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"),	/* OMAP ISP */
-	REGULATOR_SUPPLY("vcc", "usb_phy_gen_xceiv.2"),	/* hsusb port 2 */
-	REGULATOR_SUPPLY("vaux2", NULL),
-};
-
-static struct regulator_init_data omap3evm_vaux2 = {
-	.constraints = {
-		.min_uV		= 2800000,
-		.max_uV		= 2800000,
-		.apply_uV	= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies		= ARRAY_SIZE(omap3evm_vaux2_supplies),
-	.consumer_supplies		= omap3evm_vaux2_supplies,
-};
-
-static struct twl4030_platform_data omap3evm_twldata = {
-	/* platform_data for children goes here */
-	.keypad		= &omap3evm_kp_data,
-	.gpio		= &omap3evm_gpio_data,
-	.vio		= &omap3evm_vio,
-	.vmmc1		= &omap3evm_vmmc1,
-	.vsim		= &omap3evm_vsim,
-};
-
-static int __init omap3_evm_i2c_init(void)
-{
-	omap3_pmic_get_config(&omap3evm_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
-			TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	omap3evm_twldata.vdac->constraints.apply_uV = true;
-	omap3evm_twldata.vpll2->constraints.apply_uV = true;
-
-	omap3_pmic_init("twl4030", &omap3evm_twldata);
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	omap_register_i2c_bus(3, 400, NULL, 0);
-	return 0;
-}
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = -1,	/* set at runtime */
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux omap35x_board_mux[] __initdata = {
-	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
-				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
-				OMAP_PIN_OFF_WAKEUPENABLE),
-	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
-				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
-				OMAP_PIN_OFF_WAKEUPENABLE),
-	OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
-				OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
-				OMAP_PIN_OFF_NONE),
-#ifdef CONFIG_WILINK_PLATFORM_DATA
-	/* WLAN IRQ - GPIO 149 */
-	OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
-	/* WLAN POWER ENABLE - GPIO 150 */
-	OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
-	/* MMC2 SDIO pin muxes for WL12xx */
-	OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-#endif
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-
-static struct omap_board_mux omap36x_board_mux[] __initdata = {
-	OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP |
-				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
-				OMAP_PIN_OFF_WAKEUPENABLE),
-	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP |
-				OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW |
-				OMAP_PIN_OFF_WAKEUPENABLE),
-	/* AM/DM37x EVM: DSS data bus muxed with sys_boot */
-	OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(SYS_BOOT0, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(SYS_BOOT1, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(SYS_BOOT3, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(SYS_BOOT4, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-	OMAP3_MUX(SYS_BOOT6, OMAP_MUX_MODE3 | OMAP_PIN_OFF_NONE),
-#ifdef CONFIG_WILINK_PLATFORM_DATA
-	/* WLAN IRQ - GPIO 149 */
-	OMAP3_MUX(UART1_RTS, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-
-	/* WLAN POWER ENABLE - GPIO 150 */
-	OMAP3_MUX(UART1_CTS, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-
-	/* MMC2 SDIO pin muxes for WL12xx */
-	OMAP3_MUX(SDMMC2_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_CMD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(SDMMC2_DAT3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLUP),
-#endif
-
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#else
-#define omap35x_board_mux	NULL
-#define omap36x_board_mux	NULL
-#endif
-
-static struct omap_musb_board_data musb_board_data = {
-	.interface_type		= MUSB_INTERFACE_ULPI,
-	.mode			= MUSB_OTG,
-	.power			= 100,
-};
-
-static struct gpio omap3_evm_ehci_gpios[] __initdata = {
-	{ OMAP3_EVM_EHCI_VBUS,	 GPIOF_OUT_INIT_HIGH,  "enable EHCI VBUS" },
-	{ OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW,   "select EHCI port" },
-};
-
-static void __init omap3_evm_wl12xx_init(void)
-{
-#ifdef CONFIG_WILINK_PLATFORM_DATA
-	int ret;
-
-	/* WL12xx WLAN Init */
-	omap3evm_wlan_data.irq = gpio_to_irq(OMAP3EVM_WLAN_IRQ_GPIO);
-	ret = wl12xx_set_platform_data(&omap3evm_wlan_data);
-	if (ret)
-		pr_err("error setting wl12xx data: %d\n", ret);
-	ret = platform_device_register(&omap3evm_wlan_regulator);
-	if (ret)
-		pr_err("error registering wl12xx device: %d\n", ret);
-#endif
-}
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static struct mtd_partition omap3evm_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name           = "X-Loader",
-		.offset         = 0,
-		.size           = 4*(SZ_128K),
-		.mask_flags     = MTD_WRITEABLE
-	},
-	{
-		.name           = "U-Boot",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 14*(SZ_128K),
-		.mask_flags     = MTD_WRITEABLE
-	},
-	{
-		.name           = "U-Boot Env",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 2*(SZ_128K)
-	},
-	{
-		.name           = "Kernel",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 40*(SZ_128K)
-	},
-	{
-		.name           = "File system",
-		.size           = MTDPART_SIZ_FULL,
-		.offset         = MTDPART_OFS_APPEND,
-	},
-};
-
-static void __init omap3_evm_init(void)
-{
-	struct omap_board_mux *obm;
-
-	omap3_evm_get_revision();
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-
-	obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux;
-	omap3_mux_init(obm, OMAP_PACKAGE_CBB);
-
-	omap_mux_init_gpio(63, OMAP_PIN_INPUT);
-	omap_hsmmc_init(mmc);
-
-	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
-		omap3evm_twldata.vaux2 = &omap3evm_vaux2;
-
-	omap3_evm_i2c_init();
-
-	omap_display_init(&omap3_evm_dss_data);
-	platform_device_register(&omap3_evm_lcd_device);
-	platform_device_register(&omap3_evm_tfp410_device);
-	platform_device_register(&omap3_evm_dvi_connector_device);
-	platform_device_register(&omap3_evm_tv_connector_device);
-
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
-
-	/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
-	usb_nop_xceiv_register();
-
-	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
-		/* enable EHCI VBUS using GPIO22 */
-		omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
-		/* Select EHCI port on main board */
-		omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
-				   OMAP_PIN_INPUT_PULLUP);
-		gpio_request_array(omap3_evm_ehci_gpios,
-				   ARRAY_SIZE(omap3_evm_ehci_gpios));
-
-		/* setup EHCI phy reset config */
-		omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
-		phy_data[0].reset_gpio = 21;
-
-		/* EVM REV >= E can supply 500mA with EXTVBUS programming */
-		musb_board_data.power = 500;
-		musb_board_data.extvbus = 1;
-	} else {
-		/* setup EHCI phy reset on MDC */
-		omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
-		phy_data[0].reset_gpio = 135;
-	}
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(&musb_board_data);
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-	board_nand_init(omap3evm_nand_partitions,
-			ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS,
-			NAND_BUSWIDTH_16, NULL);
-
-	omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
-	omap3evm_init_smsc911x();
-#ifdef CONFIG_BROKEN
-	omap3_evm_display_init();
-#endif
-	omap3_evm_wl12xx_init();
-	omap_twl4030_audio_init("omap3evm", NULL);
-}
-
-MACHINE_START(OMAP3EVM, "OMAP3 EVM")
-	/* Maintainer: Syed Mohammed Khasim - Texas Instruments */
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= omap3_evm_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-rm680.c b/arch/arm/mach-omap2/board-rm680.c
deleted file mode 100644
index 345e8c4..0000000
--- a/arch/arm/mach-omap2/board-rm680.c
+++ /dev/null
@@ -1,167 +0,0 @@
-/*
- * Board support file for Nokia N950 (RM-680) / N9 (RM-696).
- *
- * Copyright (C) 2010 Nokia
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/io.h>
-#include <linux/i2c.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/i2c/twl.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/consumer.h>
-#include <linux/platform_data/mtd-onenand-omap2.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach-types.h>
-
-#include "common.h"
-#include "mux.h"
-#include "gpmc.h"
-#include "mmc.h"
-#include "hsmmc.h"
-#include "sdram-nokia.h"
-#include "common-board-devices.h"
-#include "gpmc-onenand.h"
-
-static struct regulator_consumer_supply rm680_vemmc_consumers[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-/* Fixed regulator for internal eMMC */
-static struct regulator_init_data rm680_vemmc = {
-	.constraints =	{
-		.name			= "rm680_vemmc",
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_STATUS
-					| REGULATOR_CHANGE_MODE,
-	},
-	.num_consumer_supplies		= ARRAY_SIZE(rm680_vemmc_consumers),
-	.consumer_supplies		= rm680_vemmc_consumers,
-};
-
-static struct fixed_voltage_config rm680_vemmc_config = {
-	.supply_name		= "VEMMC",
-	.microvolts		= 2900000,
-	.gpio			= 157,
-	.startup_delay		= 150,
-	.enable_high		= 1,
-	.init_data		= &rm680_vemmc,
-};
-
-static struct platform_device rm680_vemmc_device = {
-	.name			= "reg-fixed-voltage",
-	.dev			= {
-		.platform_data	= &rm680_vemmc_config,
-	},
-};
-
-static struct platform_device *rm680_peripherals_devices[] __initdata = {
-	&rm680_vemmc_device,
-};
-
-/* TWL */
-static struct twl4030_gpio_platform_data rm680_gpio_data = {
-	.pullups		= BIT(0),
-	.pulldowns		= BIT(1) | BIT(2) | BIT(8) | BIT(15),
-};
-
-static struct twl4030_platform_data rm680_twl_data = {
-	.gpio			= &rm680_gpio_data,
-	/* add rest of the children here */
-};
-
-static void __init rm680_i2c_init(void)
-{
-	omap3_pmic_get_config(&rm680_twl_data, TWL_COMMON_PDATA_USB, 0);
-	omap_pmic_init(1, 2900, "twl5031", 7 + OMAP_INTC_START, &rm680_twl_data);
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	omap_register_i2c_bus(3, 400, NULL, 0);
-}
-
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
-	defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
-static struct omap_onenand_platform_data board_onenand_data[] = {
-	{
-		.gpio_irq	= 65,
-		.flags		= ONENAND_SYNC_READWRITE,
-	}
-};
-#endif
-
-/* eMMC */
-static struct omap2_hsmmc_info mmc[] __initdata = {
-	{
-		.name		= "internal",
-		.mmc		= 2,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_MMC_HIGHSPEED,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-	},
-	{ /* Terminator */ }
-};
-
-static void __init rm680_peripherals_init(void)
-{
-	platform_add_devices(rm680_peripherals_devices,
-				ARRAY_SIZE(rm680_peripherals_devices));
-	rm680_i2c_init();
-	gpmc_onenand_init(board_onenand_data);
-	omap_hsmmc_init(mmc);
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init rm680_init(void)
-{
-	struct omap_sdrc_params *sdrc_params;
-
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	omap_serial_init();
-
-	sdrc_params = nokia_get_sdram_timings();
-	omap_sdrc_init(sdrc_params, sdrc_params);
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-	rm680_peripherals_init();
-}
-
-MACHINE_START(NOKIA_RM680, "Nokia RM-680 board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3630_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= rm680_init,
-	.init_late	= omap3630_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(NOKIA_RM696, "Nokia RM-696 board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3630_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= rm680_init,
-	.init_late	= omap3630_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-zoom-debugboard.c b/arch/arm/mach-omap2/board-zoom-debugboard.c
deleted file mode 100644
index 42e5f23..0000000
--- a/arch/arm/mach-omap2/board-zoom-debugboard.c
+++ /dev/null
@@ -1,139 +0,0 @@
-/*
- * Copyright (C) 2009 Texas Instruments Inc.
- * Mikkel Christensen <mlc@ti.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/gpio.h>
-#include <linux/serial_8250.h>
-#include <linux/smsc911x.h>
-#include <linux/interrupt.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include "gpmc.h"
-#include "gpmc-smsc911x.h"
-
-#include "board-zoom.h"
-
-#include "soc.h"
-#include "common.h"
-
-#define ZOOM_SMSC911X_CS	7
-#define ZOOM_SMSC911X_GPIO	158
-#define ZOOM_QUADUART_CS	3
-#define ZOOM_QUADUART_GPIO	102
-#define ZOOM_QUADUART_RST_GPIO	152
-#define QUART_CLK		1843200
-#define DEBUG_BASE		0x08000000
-#define ZOOM_ETHR_START	DEBUG_BASE
-
-static struct omap_smsc911x_platform_data zoom_smsc911x_cfg = {
-	.cs             = ZOOM_SMSC911X_CS,
-	.gpio_irq       = ZOOM_SMSC911X_GPIO,
-	.gpio_reset     = -EINVAL,
-	.flags		= SMSC911X_USE_32BIT,
-};
-
-static inline void __init zoom_init_smsc911x(void)
-{
-	gpmc_smsc911x_init(&zoom_smsc911x_cfg);
-}
-
-static struct plat_serial8250_port serial_platform_data[] = {
-	{
-		.mapbase	= ZOOM_UART_BASE,
-		.flags		= UPF_BOOT_AUTOCONF|UPF_IOREMAP|UPF_SHARE_IRQ,
-		.irqflags	= IRQF_SHARED | IRQF_TRIGGER_RISING,
-		.iotype		= UPIO_MEM,
-		.regshift	= 1,
-		.uartclk	= QUART_CLK,
-	}, {
-		.flags		= 0
-	}
-};
-
-static struct platform_device zoom_debugboard_serial_device = {
-	.name			= "serial8250",
-	.id			= PLAT8250_DEV_PLATFORM,
-	.dev			= {
-		.platform_data	= serial_platform_data,
-	},
-};
-
-static inline void __init zoom_init_quaduart(void)
-{
-	int quart_cs;
-	unsigned long cs_mem_base;
-	int quart_gpio = 0;
-
-	if (gpio_request_one(ZOOM_QUADUART_RST_GPIO,
-				GPIOF_OUT_INIT_LOW,
-				"TL16CP754C GPIO") < 0) {
-		pr_err("Failed to request GPIO%d for TL16CP754C\n",
-			ZOOM_QUADUART_RST_GPIO);
-		return;
-	}
-
-	quart_cs = ZOOM_QUADUART_CS;
-
-	if (gpmc_cs_request(quart_cs, SZ_1M, &cs_mem_base) < 0) {
-		pr_err("Failed to request GPMC mem for Quad UART(TL16CP754C)\n");
-		return;
-	}
-
-	quart_gpio = ZOOM_QUADUART_GPIO;
-
-	if (gpio_request_one(quart_gpio, GPIOF_IN, "TL16CP754C GPIO") < 0)
-		printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n",
-								quart_gpio);
-
-	serial_platform_data[0].irq = gpio_to_irq(102);
-}
-
-static inline int omap_zoom_debugboard_detect(void)
-{
-	int debug_board_detect = 0;
-	int ret = 1;
-
-	debug_board_detect = ZOOM_SMSC911X_GPIO;
-
-	if (gpio_request_one(debug_board_detect, GPIOF_IN,
-			     "Zoom debug board detect") < 0) {
-		pr_err("Failed to request GPIO%d for Zoom debug board detect\n",
-		       debug_board_detect);
-		return 0;
-	}
-
-	if (!gpio_get_value(debug_board_detect)) {
-		ret = 0;
-	}
-	gpio_free(debug_board_detect);
-	return ret;
-}
-
-static struct platform_device *zoom_devices[] __initdata = {
-	&zoom_debugboard_serial_device,
-};
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-int __init zoom_debugboard_init(void)
-{
-	if (!omap_zoom_debugboard_detect())
-		return 0;
-
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-	zoom_init_smsc911x();
-	zoom_init_quaduart();
-	return platform_add_devices(zoom_devices, ARRAY_SIZE(zoom_devices));
-}
diff --git a/arch/arm/mach-omap2/board-zoom-display.c b/arch/arm/mach-omap2/board-zoom-display.c
deleted file mode 100644
index 3d8ecc1e..0000000
--- a/arch/arm/mach-omap2/board-zoom-display.c
+++ /dev/null
@@ -1,71 +0,0 @@
-/*
- * Copyright (C) 2010 Texas Instruments Inc.
- *
- * Modified from mach-omap2/board-zoom-peripherals.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/spi/spi.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-
-#include "board-zoom.h"
-#include "soc.h"
-#include "common.h"
-
-#define LCD_PANEL_RESET_GPIO_PROD	96
-#define LCD_PANEL_RESET_GPIO_PILOT	55
-#define LCD_PANEL_QVGA_GPIO		56
-
-static struct panel_nec_nl8048hl11_platform_data zoom_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 24,
-
-	.res_gpio		= -1,	/* filled in code */
-	.qvga_gpio		= LCD_PANEL_QVGA_GPIO,
-};
-
-static struct omap_dss_board_info zoom_dss_data = {
-	.default_display_name = "lcd",
-};
-
-static void __init zoom_lcd_panel_init(void)
-{
-	zoom_lcd_pdata.res_gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
-			LCD_PANEL_RESET_GPIO_PROD :
-			LCD_PANEL_RESET_GPIO_PILOT;
-}
-
-static struct omap2_mcspi_device_config dss_lcd_mcspi_config = {
-	.turbo_mode		= 1,
-};
-
-static struct spi_board_info nec_8048_spi_board_info[] __initdata = {
-	[0] = {
-		.modalias		= "panel-nec-nl8048hl11",
-		.bus_num		= 1,
-		.chip_select		= 2,
-		.max_speed_hz		= 375000,
-		.controller_data	= &dss_lcd_mcspi_config,
-		.platform_data		= &zoom_lcd_pdata,
-	},
-};
-
-void __init zoom_display_init(void)
-{
-	omap_display_init(&zoom_dss_data);
-	zoom_lcd_panel_init();
-	spi_register_board_info(nec_8048_spi_board_info,
-				ARRAY_SIZE(nec_8048_spi_board_info));
-}
-
diff --git a/arch/arm/mach-omap2/board-zoom-peripherals.c b/arch/arm/mach-omap2/board-zoom-peripherals.c
deleted file mode 100644
index a90375d..0000000
--- a/arch/arm/mach-omap2/board-zoom-peripherals.c
+++ /dev/null
@@ -1,360 +0,0 @@
-/*
- * Copyright (C) 2009 Texas Instruments Inc.
- *
- * Modified from mach-omap2/board-zoom2.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/gpio.h>
-#include <linux/i2c/twl.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/wl12xx.h>
-#include <linux/mmc/host.h>
-#include <linux/platform_data/gpio-omap.h>
-#include <linux/platform_data/omap-twl4030.h>
-#include <linux/usb/phy.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-#include <linux/pwm_backlight.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-
-#include "board-zoom.h"
-
-#include "mux.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#define OMAP_ZOOM_WLAN_PMENA_GPIO	(101)
-#define OMAP_ZOOM_TSC2004_IRQ_GPIO	(153)
-#define OMAP_ZOOM_WLAN_IRQ_GPIO		(162)
-
-/* Zoom2 has Qwerty keyboard*/
-static uint32_t board_keymap[] = {
-	KEY(0, 0, KEY_E),
-	KEY(0, 1, KEY_R),
-	KEY(0, 2, KEY_T),
-	KEY(0, 3, KEY_HOME),
-	KEY(0, 6, KEY_I),
-	KEY(0, 7, KEY_LEFTSHIFT),
-	KEY(1, 0, KEY_D),
-	KEY(1, 1, KEY_F),
-	KEY(1, 2, KEY_G),
-	KEY(1, 3, KEY_SEND),
-	KEY(1, 6, KEY_K),
-	KEY(1, 7, KEY_ENTER),
-	KEY(2, 0, KEY_X),
-	KEY(2, 1, KEY_C),
-	KEY(2, 2, KEY_V),
-	KEY(2, 3, KEY_END),
-	KEY(2, 6, KEY_DOT),
-	KEY(2, 7, KEY_CAPSLOCK),
-	KEY(3, 0, KEY_Z),
-	KEY(3, 1, KEY_KPPLUS),
-	KEY(3, 2, KEY_B),
-	KEY(3, 3, KEY_F1),
-	KEY(3, 6, KEY_O),
-	KEY(3, 7, KEY_SPACE),
-	KEY(4, 0, KEY_W),
-	KEY(4, 1, KEY_Y),
-	KEY(4, 2, KEY_U),
-	KEY(4, 3, KEY_F2),
-	KEY(4, 4, KEY_VOLUMEUP),
-	KEY(4, 6, KEY_L),
-	KEY(4, 7, KEY_LEFT),
-	KEY(5, 0, KEY_S),
-	KEY(5, 1, KEY_H),
-	KEY(5, 2, KEY_J),
-	KEY(5, 3, KEY_F3),
-	KEY(5, 4, KEY_UNKNOWN),
-	KEY(5, 5, KEY_VOLUMEDOWN),
-	KEY(5, 6, KEY_M),
-	KEY(5, 7, KEY_RIGHT),
-	KEY(6, 0, KEY_Q),
-	KEY(6, 1, KEY_A),
-	KEY(6, 2, KEY_N),
-	KEY(6, 3, KEY_BACKSPACE),
-	KEY(6, 6, KEY_P),
-	KEY(6, 7, KEY_UP),
-	KEY(7, 0, KEY_PROG1),	/*MACRO 1 <User defined> */
-	KEY(7, 1, KEY_PROG2),	/*MACRO 2 <User defined> */
-	KEY(7, 2, KEY_PROG3),	/*MACRO 3 <User defined> */
-	KEY(7, 3, KEY_PROG4),	/*MACRO 4 <User defined> */
-	KEY(7, 6, KEY_SELECT),
-	KEY(7, 7, KEY_DOWN)
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap			= board_keymap,
-	.keymap_size		= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data zoom_kp_twl4030_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 8,
-	.cols		= 8,
-	.rep		= 1,
-};
-
-static struct regulator_consumer_supply zoom_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply zoom_vsim_supply[] = {
-	REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply zoom_vmmc2_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
-};
-
-static struct regulator_consumer_supply zoom_vmmc3_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.2"),
-};
-
-/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data zoom_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(zoom_vmmc1_supply),
-	.consumer_supplies      = zoom_vmmc1_supply,
-};
-
-/* VMMC2 for MMC2 card */
-static struct regulator_init_data zoom_vmmc2 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 1850000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(zoom_vmmc2_supply),
-	.consumer_supplies      = zoom_vmmc2_supply,
-};
-
-/* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */
-static struct regulator_init_data zoom_vsim = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 3000000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(zoom_vsim_supply),
-	.consumer_supplies      = zoom_vsim_supply,
-};
-
-static struct regulator_init_data zoom_vmmc3 = {
-	.constraints = {
-		.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(zoom_vmmc3_supply),
-	.consumer_supplies	= zoom_vmmc3_supply,
-};
-
-static struct fixed_voltage_config zoom_vwlan = {
-	.supply_name		= "vwl1271",
-	.microvolts		= 1800000, /* 1.8V */
-	.gpio			= OMAP_ZOOM_WLAN_PMENA_GPIO,
-	.startup_delay		= 70000, /* 70msec */
-	.enable_high		= 1,
-	.enabled_at_boot	= 0,
-	.init_data		= &zoom_vmmc3,
-};
-
-static struct platform_device omap_vwlan_device = {
-	.name		= "reg-fixed-voltage",
-	.id		= 1,
-	.dev = {
-		.platform_data	= &zoom_vwlan,
-	},
-};
-
-static struct pwm_lookup zoom_pwm_lookup[] = {
-	PWM_LOOKUP("twl-pwm", 0, "leds_pwm", "zoom::keypad"),
-	PWM_LOOKUP("twl-pwm", 1, "pwm-backlight", "backlight"),
-};
-
-static struct led_pwm zoom_pwm_leds[] = {
-	{
-		.name		= "zoom::keypad",
-		.max_brightness	= 127,
-		.pwm_period_ns	= 7812500,
-	},
-};
-
-static struct led_pwm_platform_data zoom_pwm_data = {
-	.num_leds	= ARRAY_SIZE(zoom_pwm_leds),
-	.leds		= zoom_pwm_leds,
-};
-
-static struct platform_device zoom_leds_pwm = {
-	.name	= "leds_pwm",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &zoom_pwm_data,
-	},
-};
-
-static struct platform_pwm_backlight_data zoom_backlight_data = {
-	.pwm_id = 1,
-	.max_brightness = 127,
-	.dft_brightness = 127,
-	.pwm_period_ns = 7812500,
-};
-
-static struct platform_device zoom_backlight_pwm = {
-	.name   = "pwm-backlight",
-	.id     = -1,
-	.dev    = {
-		.platform_data = &zoom_backlight_data,
-	},
-};
-
-static struct platform_device *zoom_devices[] __initdata = {
-	&omap_vwlan_device,
-	&zoom_leds_pwm,
-	&zoom_backlight_pwm,
-};
-
-static struct wl12xx_platform_data omap_zoom_wlan_data __initdata = {
-	.board_ref_clock = WL12XX_REFCLOCK_26, /* 26 MHz */
-};
-
-static struct omap2_hsmmc_info mmc[] = {
-	{
-		.name		= "external",
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_wp	= -EINVAL,
-		.power_saving	= true,
-		.deferred	= true,
-	},
-	{
-		.name		= "internal",
-		.mmc		= 2,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-		.nonremovable	= true,
-		.power_saving	= true,
-	},
-	{
-		.name		= "wl1271",
-		.mmc		= 3,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
-		.gpio_wp	= -EINVAL,
-		.gpio_cd	= -EINVAL,
-		.nonremovable	= true,
-	},
-	{}      /* Terminator */
-};
-
-static struct omap_tw4030_pdata omap_twl4030_audio_data = {
-	.voice_connected = true,
-	.custom_routing	= true,
-
-	.has_hs		= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
-	.has_hf		= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
-
-	.has_mainmic	= true,
-	.has_submic	= true,
-	.has_hsmic	= true,
-	.has_linein	= OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
-};
-
-static int zoom_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	/* gpio + 0 is "mmc0_cd" (input/IRQ) */
-	mmc[0].gpio_cd = gpio + 0;
-	omap_hsmmc_late_init(mmc);
-
-	/* Audio setup */
-	omap_twl4030_audio_data.jack_detect = gpio + 2;
-	omap_twl4030_audio_init("Zoom2", &omap_twl4030_audio_data);
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data zoom_gpio_data = {
-	.setup		= zoom_twl_gpio_setup,
-};
-
-static struct twl4030_platform_data zoom_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &zoom_gpio_data,
-	.keypad		= &zoom_kp_twl4030_data,
-	.vmmc1          = &zoom_vmmc1,
-	.vmmc2          = &zoom_vmmc2,
-	.vsim           = &zoom_vsim,
-};
-
-static int __init omap_i2c_init(void)
-{
-	omap3_pmic_get_config(&zoom_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI |
-			TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	if (machine_is_omap_zoom2())
-		zoom_twldata.audio->codec->ramp_delay_value = 3; /* 161 ms */
-
-	omap_pmic_init(1, 2400, "twl5030", 7 + OMAP_INTC_START, &zoom_twldata);
-	omap_register_i2c_bus(2, 400, NULL, 0);
-	omap_register_i2c_bus(3, 400, NULL, 0);
-	return 0;
-}
-
-static void enable_board_wakeup_source(void)
-{
-	/* T2 interrupt line (keypad) */
-	omap_mux_init_signal("sys_nirq",
-		OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
-}
-
-void __init zoom_peripherals_init(void)
-{
-	int ret;
-
-	omap_zoom_wlan_data.irq = gpio_to_irq(OMAP_ZOOM_WLAN_IRQ_GPIO);
-	ret = wl12xx_set_platform_data(&omap_zoom_wlan_data);
-
-	if (ret)
-		pr_err("error setting wl12xx data: %d\n", ret);
-
-	omap_hsmmc_init(mmc);
-	omap_i2c_init();
-	pwm_add_table(zoom_pwm_lookup, ARRAY_SIZE(zoom_pwm_lookup));
-	platform_add_devices(zoom_devices, ARRAY_SIZE(zoom_devices));
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-	enable_board_wakeup_source();
-	omap_serial_init();
-}
diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c
deleted file mode 100644
index 1a3dd86..0000000
--- a/arch/arm/mach-omap2/board-zoom.c
+++ /dev/null
@@ -1,159 +0,0 @@
-/*
- * Copyright (C) 2009-2010 Texas Instruments Inc.
- * Mikkel Christensen <mlc@ti.com>
- * Felipe Balbi <balbi@ti.com>
- *
- * Modified from mach-omap2/board-ldp.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/input.h>
-#include <linux/gpio.h>
-#include <linux/i2c/twl.h>
-#include <linux/mtd/nand.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include "common.h"
-
-#include "board-zoom.h"
-
-#include "board-flash.h"
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "sdram-hynix-h8mbx00u0mer-0em.h"
-
-#define ZOOM3_EHCI_RESET_GPIO		64
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* WLAN IRQ - GPIO 162 */
-	OMAP3_MUX(MCBSP1_CLKX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
-	/* WLAN POWER ENABLE - GPIO 101 */
-	OMAP3_MUX(CAM_D2, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
-	/* WLAN SDIO: MMC3 CMD */
-	OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLUP),
-	/* WLAN SDIO: MMC3 CLK */
-	OMAP3_MUX(ETK_CLK, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
-	/* WLAN SDIO: MMC3 DAT[0-3] */
-	OMAP3_MUX(ETK_D3, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(ETK_D4, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(ETK_D5, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
-	OMAP3_MUX(ETK_D6, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct mtd_partition zoom_nand_partitions[] = {
-	/* All the partition sizes are listed in terms of NAND block size */
-	{
-		.name		= "X-Loader-NAND",
-		.offset		= 0,
-		.size		= 4 * (64 * 2048),	/* 512KB, 0x80000 */
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "U-Boot-NAND",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
-		.size		= 10 * (64 * 2048),	/* 1.25MB, 0x140000 */
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	{
-		.name		= "Boot Env-NAND",
-		.offset		= MTDPART_OFS_APPEND,   /* Offset = 0x1c0000 */
-		.size		= 2 * (64 * 2048),	/* 256KB, 0x40000 */
-	},
-	{
-		.name		= "Kernel-NAND",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x0200000*/
-		.size		= 240 * (64 * 2048),	/* 30M, 0x1E00000 */
-	},
-	{
-		.name		= "system",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x2000000 */
-		.size		= 3328 * (64 * 2048),	/* 416M, 0x1A000000 */
-	},
-	{
-		.name		= "userdata",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x1C000000*/
-		.size		= 256 * (64 * 2048),	/* 32M, 0x2000000 */
-	},
-	{
-		.name		= "cache",
-		.offset		= MTDPART_OFS_APPEND,	/* Offset = 0x1E000000*/
-		.size		= 256 * (64 * 2048),	/* 32M, 0x2000000 */
-	},
-};
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = ZOOM3_EHCI_RESET_GPIO,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[1]		= OMAP_EHCI_PORT_MODE_PHY,
-};
-
-static void __init omap_zoom_init(void)
-{
-	if (machine_is_omap_zoom2()) {
-		omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	} else if (machine_is_omap_zoom3()) {
-		omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
-		omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT);
-
-		usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-		usbhs_init(&usbhs_bdata);
-	}
-
-	board_nand_init(zoom_nand_partitions,
-			ARRAY_SIZE(zoom_nand_partitions), ZOOM_NAND_CS,
-			NAND_BUSWIDTH_16, nand_default_timings);
-	zoom_debugboard_init();
-	zoom_peripherals_init();
-
-	if (machine_is_omap_zoom2())
-		omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-					  mt46h32m32lf6_sdrc_params);
-	else if (machine_is_omap_zoom3())
-		omap_sdrc_init(h8mbx00u0mer0em_sdrc_params,
-					  h8mbx00u0mer0em_sdrc_params);
-
-	zoom_display_init();
-}
-
-MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3430_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= omap_zoom_init,
-	.init_late	= omap3430_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(OMAP_ZOOM3, "OMAP Zoom3 board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap3630_init_early,
-	.init_irq	= omap3_init_irq,
-	.handle_irq	= omap3_intc_handle_irq,
-	.init_machine	= omap_zoom_init,
-	.init_late	= omap3630_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-omap2/board-zoom.h b/arch/arm/mach-omap2/board-zoom.h
deleted file mode 100644
index 2e94869..0000000
--- a/arch/arm/mach-omap2/board-zoom.h
+++ /dev/null
@@ -1,10 +0,0 @@
-/*
- * Defines for zoom boards
- */
-#include <video/omapdss.h>
-
-#define ZOOM_NAND_CS    0
-
-extern int __init zoom_debugboard_init(void);
-extern void __init zoom_peripherals_init(void);
-extern void __init zoom_display_init(void);
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 4a5684b..f7644fe 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -98,6 +98,7 @@ void am35xx_init_early(void);
 void ti81xx_init_early(void);
 void am33xx_init_early(void);
 void am43xx_init_early(void);
+void am43xx_init_late(void);
 void omap4430_init_early(void);
 void omap5_init_early(void);
 void omap3_init_late(void);	/* Do not use this one */
@@ -109,8 +110,11 @@ void omap35xx_init_late(void);
 void omap3630_init_late(void);
 void am35xx_init_late(void);
 void ti81xx_init_late(void);
+void am33xx_init_late(void);
+void omap5_init_late(void);
 int omap2_common_pm_late_init(void);
 void dra7xx_init_early(void);
+void dra7xx_init_late(void);
 
 #ifdef CONFIG_SOC_BUS
 void omap_soc_device_init(void);
@@ -288,6 +292,9 @@ static inline void omap4_cpu_resume(void)
 
 #endif
 
+void pdata_quirks_init(struct of_device_id *);
+void omap_pcs_legacy_init(int irq, void (*rearm)(void));
+
 struct omap_sdrc_params;
 extern void omap_sdrc_init(struct omap_sdrc_params *sdrc_cs0,
 				      struct omap_sdrc_params *sdrc_cs1);
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 89a8698..0dd6398 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -19,7 +19,6 @@
 #include <linux/of.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_data/omap4-keypad.h>
-#include <linux/wl12xx.h>
 #include <linux/platform_data/mailbox-omap.h>
 
 #include <asm/mach-types.h>
@@ -476,40 +475,6 @@ int __init omap_init_vout(void)
 int __init omap_init_vout(void) { return 0; }
 #endif
 
-#if IS_ENABLED(CONFIG_WL12XX)
-
-static struct wl12xx_platform_data wl12xx __initdata;
-
-void __init omap_init_wl12xx_of(void)
-{
-	int ret;
-
-	if (!of_have_populated_dt())
-		return;
-
-	if (of_machine_is_compatible("ti,omap4-sdp")) {
-		wl12xx.board_ref_clock = WL12XX_REFCLOCK_26;
-		wl12xx.board_tcxo_clock = WL12XX_TCXOCLOCK_26;
-		wl12xx.irq = gpio_to_irq(53);
-	} else if (of_machine_is_compatible("ti,omap4-panda")) {
-		wl12xx.board_ref_clock = WL12XX_REFCLOCK_38;
-		wl12xx.irq = gpio_to_irq(53);
-	} else {
-		return;
-	}
-
-	ret = wl12xx_set_platform_data(&wl12xx);
-	if (ret) {
-		pr_err("error setting wl12xx data: %d\n", ret);
-		return;
-	}
-}
-#else
-static inline void omap_init_wl12xx_of(void)
-{
-}
-#endif
-
 /*-------------------------------------------------------------------------*/
 
 static int __init omap2_init_devices(void)
@@ -532,9 +497,6 @@ static int __init omap2_init_devices(void)
 		omap_init_sham();
 		omap_init_aes();
 		omap_init_rng();
-	} else {
-		/* These can be removed when bindings are done */
-		omap_init_wl12xx_of();
 	}
 	omap_init_sti();
 
diff --git a/arch/arm/mach-omap2/dss-common.c b/arch/arm/mach-omap2/dss-common.c
index bf89eff..365bfd3 100644
--- a/arch/arm/mach-omap2/dss-common.c
+++ b/arch/arm/mach-omap2/dss-common.c
@@ -213,3 +213,47 @@ void __init omap_4430sdp_display_init_of(void)
 	platform_device_register(&sdp4430_tpd_device);
 	platform_device_register(&sdp4430_hdmi_connector_device);
 }
+
+
+/* OMAP3 IGEPv2 data */
+
+#define IGEP2_DVI_TFP410_POWER_DOWN_GPIO	170
+
+/* DVI Connector */
+static struct connector_dvi_platform_data omap3_igep2_dvi_connector_pdata = {
+	.name                   = "dvi",
+	.source                 = "tfp410.0",
+	.i2c_bus_num            = 3,
+};
+
+static struct platform_device omap3_igep2_dvi_connector_device = {
+	.name                   = "connector-dvi",
+	.id                     = 0,
+	.dev.platform_data      = &omap3_igep2_dvi_connector_pdata,
+};
+
+/* TFP410 DPI-to-DVI chip */
+static struct encoder_tfp410_platform_data omap3_igep2_tfp410_pdata = {
+	.name                   = "tfp410.0",
+	.source                 = "dpi.0",
+	.data_lines             = 24,
+	.power_down_gpio        = IGEP2_DVI_TFP410_POWER_DOWN_GPIO,
+};
+
+static struct platform_device omap3_igep2_tfp410_device = {
+	.name                   = "tfp410",
+	.id                     = 0,
+	.dev.platform_data      = &omap3_igep2_tfp410_pdata,
+};
+
+static struct omap_dss_board_info igep2_dss_data = {
+	.default_display_name = "dvi",
+};
+
+void __init omap3_igep2_display_init_of(void)
+{
+	omap_display_init(&igep2_dss_data);
+
+	platform_device_register(&omap3_igep2_tfp410_device);
+	platform_device_register(&omap3_igep2_dvi_connector_device);
+}
diff --git a/arch/arm/mach-omap2/dss-common.h b/arch/arm/mach-omap2/dss-common.h
index c28fe3c..a9becf0 100644
--- a/arch/arm/mach-omap2/dss-common.h
+++ b/arch/arm/mach-omap2/dss-common.h
@@ -8,5 +8,6 @@
 
 void __init omap4_panda_display_init_of(void);
 void __init omap_4430sdp_display_init_of(void);
+void __init omap3_igep2_display_init_of(void);
 
 #endif
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index 579697a..51525fa 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -1521,6 +1521,42 @@ err:
 	return ret;
 }
 
+/*
+ * REVISIT: Add timing support from slls644g.pdf
+ */
+static int gpmc_probe_8250(struct platform_device *pdev,
+				struct device_node *child)
+{
+	struct resource res;
+	unsigned long base;
+	int ret, cs;
+
+	if (of_property_read_u32(child, "reg", &cs) < 0) {
+		dev_err(&pdev->dev, "%s has no 'reg' property\n",
+			child->full_name);
+		return -ENODEV;
+	}
+
+	if (of_address_to_resource(child, 0, &res) < 0) {
+		dev_err(&pdev->dev, "%s has malformed 'reg' property\n",
+			child->full_name);
+		return -ENODEV;
+	}
+
+	ret = gpmc_cs_request(cs, resource_size(&res), &base);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "cannot request GPMC CS %d\n", cs);
+		return ret;
+	}
+
+	if (of_platform_device_create(child, NULL, &pdev->dev))
+		return 0;
+
+	dev_err(&pdev->dev, "failed to create gpmc child %s\n", child->name);
+
+	return -ENODEV;
+}
+
 static int gpmc_probe_dt(struct platform_device *pdev)
 {
 	int ret;
@@ -1564,6 +1600,8 @@ static int gpmc_probe_dt(struct platform_device *pdev)
 		else if (of_node_cmp(child->name, "ethernet") == 0 ||
 			 of_node_cmp(child->name, "nor") == 0)
 			ret = gpmc_probe_generic_child(pdev, child);
+		else if (of_node_cmp(child->name, "8250") == 0)
+			ret = gpmc_probe_8250(pdev, child);
 
 		if (WARN(ret < 0, "%s: probing gpmc child %s failed\n",
 			 __func__, child->full_name))
diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c
index c90f647..cd22262 100644
--- a/arch/arm/mach-omap2/io.c
+++ b/arch/arm/mach-omap2/io.c
@@ -583,6 +583,11 @@ void __init am33xx_init_early(void)
 	omap_hwmod_init_postsetup();
 	omap_clk_init = am33xx_clk_init;
 }
+
+void __init am33xx_init_late(void)
+{
+	omap_common_late_init();
+}
 #endif
 
 #ifdef CONFIG_SOC_AM43XX
@@ -602,6 +607,11 @@ void __init am43xx_init_early(void)
 	am43xx_hwmod_init();
 	omap_hwmod_init_postsetup();
 }
+
+void __init am43xx_init_late(void)
+{
+	omap_common_late_init();
+}
 #endif
 
 #ifdef CONFIG_ARCH_OMAP4
@@ -657,6 +667,11 @@ void __init omap5_init_early(void)
 	omap54xx_hwmod_init();
 	omap_hwmod_init_postsetup();
 }
+
+void __init omap5_init_late(void)
+{
+	omap_common_late_init();
+}
 #endif
 
 #ifdef CONFIG_SOC_DRA7XX
@@ -677,6 +692,11 @@ void __init dra7xx_init_early(void)
 	dra7xx_hwmod_init();
 	omap_hwmod_init_postsetup();
 }
+
+void __init dra7xx_init_late(void)
+{
+	omap_common_late_init();
+}
 #endif
 
 
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index f82cf87..48094b5 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -811,6 +811,12 @@ int __init omap_mux_late_init(void)
 		}
 	}
 
+	omap_mux_dbg_init();
+
+	/* see pinctrl-single-omap for the wake-up interrupt handling */
+	if (of_have_populated_dt())
+		return 0;
+
 	ret = request_irq(omap_prcm_event_to_irq("io"),
 		omap_hwmod_mux_handle_irq, IRQF_SHARED | IRQF_NO_SUSPEND,
 			"hwmod_io", omap_mux_late_init);
@@ -818,8 +824,6 @@ int __init omap_mux_late_init(void)
 	if (ret)
 		pr_warning("mux: Failed to setup hwmod io irq %d\n", ret);
 
-	omap_mux_dbg_init();
-
 	return 0;
 }
 
diff --git a/arch/arm/mach-omap2/opp.c b/arch/arm/mach-omap2/opp.c
index bd41d59..82fd8c7 100644
--- a/arch/arm/mach-omap2/opp.c
+++ b/arch/arm/mach-omap2/opp.c
@@ -17,6 +17,7 @@
  * GNU General Public License for more details.
  */
 #include <linux/module.h>
+#include <linux/of.h>
 #include <linux/opp.h>
 #include <linux/cpu.h>
 
@@ -40,6 +41,9 @@ int __init omap_init_opp_table(struct omap_opp_def *opp_def,
 {
 	int i, r;
 
+	if (of_have_populated_dt())
+		return -EINVAL;
+
 	if (!opp_def || !opp_def_size) {
 		pr_err("%s: invalid params!\n", __func__);
 		return -EINVAL;
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
new file mode 100644
index 0000000..10c7145
--- /dev/null
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -0,0 +1,174 @@
+/*
+ * Legacy platform_data quirks
+ *
+ * Copyright (C) 2013 Texas Instruments
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/of_platform.h>
+#include <linux/wl12xx.h>
+
+#include <linux/platform_data/pinctrl-single.h>
+
+#include "common.h"
+#include "common-board-devices.h"
+#include "dss-common.h"
+#include "control.h"
+
+struct pdata_init {
+	const char *compatible;
+	void (*fn)(void);
+};
+
+/*
+ * Create alias for USB host PHY clock.
+ * Remove this when clock phandle can be provided via DT
+ */
+static void __init __used legacy_init_ehci_clk(char *clkname)
+{
+	int ret;
+
+	ret = clk_add_alias("main_clk", NULL, clkname, NULL);
+	if (ret)
+		pr_err("%s:Failed to add main_clk alias to %s :%d\n",
+		       __func__, clkname, ret);
+}
+
+#if IS_ENABLED(CONFIG_WL12XX)
+
+static struct wl12xx_platform_data wl12xx __initdata;
+
+static void __init __used legacy_init_wl12xx(unsigned ref_clock,
+					     unsigned tcxo_clock,
+					     int gpio)
+{
+	int res;
+
+	wl12xx.board_ref_clock = ref_clock;
+	wl12xx.board_tcxo_clock = tcxo_clock;
+	wl12xx.irq = gpio_to_irq(gpio);
+
+	res = wl12xx_set_platform_data(&wl12xx);
+	if (res) {
+		pr_err("error setting wl12xx data: %d\n", res);
+		return;
+	}
+}
+#else
+static inline void legacy_init_wl12xx(unsigned ref_clock,
+				      unsigned tcxo_clock,
+				      int gpio)
+{
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP3
+static void __init hsmmc2_internal_input_clk(void)
+{
+	u32 reg;
+
+	reg = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1);
+	reg |= OMAP2_MMCSDIO2ADPCLKISEL;
+	omap_ctrl_writel(reg, OMAP343X_CONTROL_DEVCONF1);
+}
+
+static void __init omap3_igep0020_legacy_init(void)
+{
+	omap3_igep2_display_init_of();
+}
+
+static void __init omap3_evm_legacy_init(void)
+{
+	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 149);
+}
+
+static void __init omap3_zoom_legacy_init(void)
+{
+	legacy_init_wl12xx(WL12XX_REFCLOCK_26, 0, 162);
+}
+#endif /* CONFIG_ARCH_OMAP3 */
+
+#ifdef CONFIG_ARCH_OMAP4
+static void __init omap4_sdp_legacy_init(void)
+{
+	omap_4430sdp_display_init_of();
+	legacy_init_wl12xx(WL12XX_REFCLOCK_26,
+			   WL12XX_TCXOCLOCK_26, 53);
+}
+
+static void __init omap4_panda_legacy_init(void)
+{
+	omap4_panda_display_init_of();
+	legacy_init_ehci_clk("auxclk3_ck");
+	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53);
+}
+#endif
+
+#ifdef CONFIG_SOC_OMAP5
+static void __init omap5_uevm_legacy_init(void)
+{
+	legacy_init_ehci_clk("auxclk1_ck");
+}
+#endif
+
+static struct pcs_pdata pcs_pdata;
+
+void omap_pcs_legacy_init(int irq, void (*rearm)(void))
+{
+	pcs_pdata.irq = irq;
+	pcs_pdata.rearm = rearm;
+}
+
+struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
+#ifdef CONFIG_ARCH_OMAP3
+	OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002030, "48002030.pinmux", &pcs_pdata),
+	OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002a00, "48002a00.pinmux", &pcs_pdata),
+#endif
+#ifdef CONFIG_ARCH_OMAP4
+	OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a100040, "4a100040.pinmux", &pcs_pdata),
+	OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a31e040, "4a31e040.pinmux", &pcs_pdata),
+#endif
+	{ /* sentinel */ },
+};
+
+static struct pdata_init pdata_quirks[] __initdata = {
+#ifdef CONFIG_ARCH_OMAP3
+	{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },
+	{ "nokia,omap3-n950", hsmmc2_internal_input_clk, },
+	{ "isee,omap3-igep0020", omap3_igep0020_legacy_init, },
+	{ "ti,omap3-evm-37xx", omap3_evm_legacy_init, },
+	{ "ti,omap3-zoom3", omap3_zoom_legacy_init, },
+#endif
+#ifdef CONFIG_ARCH_OMAP4
+	{ "ti,omap4-sdp", omap4_sdp_legacy_init, },
+	{ "ti,omap4-panda", omap4_panda_legacy_init, },
+#endif
+#ifdef CONFIG_SOC_OMAP5
+	{ "ti,omap5-uevm", omap5_uevm_legacy_init, },
+#endif
+	{ /* sentinel */ },
+};
+
+void __init pdata_quirks_init(struct of_device_id *omap_dt_match_table)
+{
+	struct pdata_init *quirks = pdata_quirks;
+
+	omap_sdrc_init(NULL, NULL);
+	of_platform_populate(NULL, omap_dt_match_table,
+			     omap_auxdata_lookup, NULL);
+
+	while (quirks->compatible) {
+		if (of_machine_is_compatible(quirks->compatible)) {
+			if (quirks->fn)
+				quirks->fn();
+			break;
+		}
+		quirks++;
+	}
+}
diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c
index e742118..360b2da 100644
--- a/arch/arm/mach-omap2/pm.c
+++ b/arch/arm/mach-omap2/pm.c
@@ -266,7 +266,12 @@ static void __init omap4_init_voltages(void)
 
 static inline void omap_init_cpufreq(void)
 {
-	struct platform_device_info devinfo = { .name = "omap-cpufreq", };
+	struct platform_device_info devinfo = { };
+
+	if (!of_have_populated_dt())
+		devinfo.name = "omap-cpufreq";
+	else
+		devinfo.name = "cpufreq-cpu0";
 	platform_device_register_full(&devinfo);
 }
 
@@ -300,10 +305,11 @@ int __init omap2_common_pm_late_init(void)
 		/* Smartreflex device init */
 		omap_devinit_smartreflex();
 
-		/* cpufreq dummy device instantiation */
-		omap_init_cpufreq();
 	}
 
+	/* cpufreq dummy device instantiation */
+	omap_init_cpufreq();
+
 #ifdef CONFIG_SUSPEND
 	suspend_set_ops(&omap_pm_ops);
 #endif
diff --git a/arch/arm/mach-omap2/prm3xxx.h b/arch/arm/mach-omap2/prm3xxx.h
index 277f717..f8eb833 100644
--- a/arch/arm/mach-omap2/prm3xxx.h
+++ b/arch/arm/mach-omap2/prm3xxx.h
@@ -144,7 +144,13 @@ extern u32 omap3_prm_vcvp_read(u8 offset);
 extern void omap3_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
 
-extern void omap3xxx_prm_reconfigure_io_chain(void);
+#ifdef CONFIG_ARCH_OMAP3
+void omap3xxx_prm_reconfigure_io_chain(void);
+#else
+static inline void omap3xxx_prm_reconfigure_io_chain(void)
+{
+}
+#endif
 
 /* PRM interrupt-related functions */
 extern void omap3xxx_prm_read_pending_irqs(unsigned long *events);
diff --git a/arch/arm/mach-omap2/prm44xx_54xx.h b/arch/arm/mach-omap2/prm44xx_54xx.h
index 7cd22ab..a085d9c 100644
--- a/arch/arm/mach-omap2/prm44xx_54xx.h
+++ b/arch/arm/mach-omap2/prm44xx_54xx.h
@@ -42,7 +42,13 @@ extern u32 omap4_prm_vcvp_read(u8 offset);
 extern void omap4_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
 
-extern void omap44xx_prm_reconfigure_io_chain(void);
+#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
+void omap44xx_prm_reconfigure_io_chain(void);
+#else
+static inline void omap44xx_prm_reconfigure_io_chain(void)
+{
+}
+#endif
 
 /* PRM interrupt-related functions */
 extern void omap44xx_prm_read_pending_irqs(unsigned long *events);
diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c
index 228b850..a2e1174 100644
--- a/arch/arm/mach-omap2/prm_common.c
+++ b/arch/arm/mach-omap2/prm_common.c
@@ -24,6 +24,7 @@
 #include <linux/interrupt.h>
 #include <linux/slab.h>
 
+#include "soc.h"
 #include "prm2xxx_3xxx.h"
 #include "prm2xxx.h"
 #include "prm3xxx.h"
@@ -322,6 +323,16 @@ int omap_prcm_register_chain_handler(struct omap_prcm_irq_setup *irq_setup)
 		prcm_irq_chips[i] = gc;
 	}
 
+	if (of_have_populated_dt()) {
+		int irq = omap_prcm_event_to_irq("io");
+		if (cpu_is_omap34xx())
+			omap_pcs_legacy_init(irq,
+				omap3xxx_prm_reconfigure_io_chain);
+		else
+			omap_pcs_legacy_init(irq,
+				omap44xx_prm_reconfigure_io_chain);
+	}
+
 	return 0;
 
 err: