ARM: dts: sbc-t3517: add support for sbc-t3517

Add support for CM-T3517 CoM and SBC-T3517 board.

reused common support for sbc-t3x boards
(omap3-cm-t3x.dtsi, omap3-sb-t35.dtsi):

* SB-T35 baseboard eth
* MMC1, UART3
* HS USB Port 1/2
* I2C1/3
* Heartbit led

Added basic support for:

* MMC1 wp/cd signals
* CM-T3517 Usb Hub
* WL12xx WiFi chip
* Davinci EMAC
* AM35X OTG

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

1 files changed, 136 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/omap3-cm-t3517.dts b/arch/arm/boot/dts/omap3-cm-t3517.dts
new file mode 100644
index 0000000..d00502f
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-cm-t3517.dts
@@ -0,0 +1,136 @@
+/*
+ * Support for CompuLab CM-T3517
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+#include "omap3-cm-t3x.dtsi"
+
+/ {
+	model = "CompuLab CM-T3517";
+	compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3";
+
+	vmmc:  regulator-vmmc {
+                compatible = "regulator-fixed";
+                regulator-name = "vmmc";
+                regulator-min-microvolt = <3300000>;
+                regulator-max-microvolt = <3300000>;
+        };
+
+	wl12xx_vmmc2: wl12xx_vmmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vw1271";
+		pinctrl-names = "default";
+		pinctrl-0 = <
+				&wl12xx_wkup_pins
+				&wl12xx_core_pins
+			    >;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */
+		startup-delay-us = <20000>;
+		enable-active-high;
+	};
+
+	wl12xx_vaux2: wl12xx_vaux2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271_vaux2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+};
+
+&omap3_pmx_wkup {
+
+	wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
+			OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4)	/* sys_boot4.gpio_6 */
+		>;
+	};
+};
+
+&omap3_pmx_core {
+
+	phy1_reset_pins: pinmux_hsusb1_phy_reset_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4)	/* uart2_tx.gpio_146 */
+		>;
+	};
+
+	phy2_reset_pins: pinmux_hsusb2_phy_reset_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4)	/* uart2_rx.gpio_147 */
+		>;
+	};
+
+	otg_drv_vbus: pinmux_otg_drv_vbus {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+		>;
+	};
+
+	wl12xx_core_pins: pinmux_wl12xx_core_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4)	/* gpmc_ncs5.gpio_56 */
+			OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart2_rts.gpio_145 */
+		>;
+	};
+
+	usb_hub_pins: pinmux_usb_hub_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 - USB HUB RST */
+		>;
+	};
+};
+
+&hsusb1_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&phy1_reset_pins>;
+	reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>;
+};
+
+&hsusb2_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&phy2_reset_pins>;
+	reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>;
+};
+
+&davinci_emac {
+	status = "okay";
+};
+
+&davinci_mdio {
+	status = "okay";
+};
+
+&am35x_otg_hs {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&otg_drv_vbus>;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&wl12xx_vmmc2>;
+	vmmc_aux-supply = <&wl12xx_vaux2>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+};