Merge tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman:

* Silk board with R-Car E2 (r8a7794) SoC
  - Add r1ex24002 EEPROM to DT

    Magnus Damm says "Extend the Silk board support to include U14 which is
    an I2C based EEPROM hooked up to the I2C1 bus."

  - Add GPIO keys to DT

    Magnus Damm says "Extend the Silk board support to include SW3, SW4,
    SW6 and SW12. They are all connected via GPIO lines and handled by the
    gpio-keys driver"

* Marzen board with R-Car H1 (r7a7779) SoC
  - Add SDHI0 VCCQ Regulator

    Magnus Damm says "Add support for the on-board voltage regulator hooked
    up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
    regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
    tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
    OUT goes to the pull-ups for the data pins of SDHI0."

* Porter board with R-Car M3W (r8a7791) SoC
  - Fix HDMI output routing

    Laurent Pinchart says "The HDMI encoder is connected to the RGB output
    of the DU, which is port@0, not port@1."

* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
  iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
  - Enable cmt0

* Stout board with R-Car H2 (r8a7790) SoC
  - Initial support

* Lager board with R-Car H2 (r8a7790) SoC
  - Add CEC clock for HDMI transmitter

    Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
    fixed clock for the CEC block. Specify this in the dts to enable CEC
    support."

  - Move cec_clock to root node

    By definition nodes without a bus address do not belong on the bus

* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
  - Fix "debounce-interval" property misspelling

* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
  - Add IPMMU DT nodes
  - Add VSP support

* R-Car Gen2 boards
  - Use I2C demuxer for

    This allows run-time switching between alternate I2C IP blocks

* R-Car Gen2 and RZ/G1 SoCs
  - Clean up DT files to ease future maintenance
    + add soc node for IP attached to the bus
    + sort subnodes of soc and root node
    + consistently use single space after =

* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
  - Reduce size of thermal registers

    According to the "User's Manual: Hardware" v2.00 the registers at base
    0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
    case on the r8a73a4 (R-Mobile APE6).

    This should not have any runtime affect as mapping granularity is
    PAGE_SIZE.

* tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits)
  ARM: dts: silk: Add GPIO keys to DT
  ARM: dts: silk: Add r1ex24002 EEPROM to DT
  ARM: dts: marzen: Add SDHI0 VCCQ Regulator
  ARM: dts: stout: Initial r8a7790 Stout board support
  ARM: dts: lager: Move cec_clock to root node
  ARM: dts: kzm9d: Fix "debounce-interval" property misspelling
  ARM: dts: gose: use demuxer for I2C4
  ARM: dts: gose: use demuxer for I2C2
  ARM: dts: silk: use demuxer for I2C1
  ARM: dts: alt: use demuxer for I2C1
  ARM: dts: porter: use demuxer for I2C2
  ARM: dts: koelsch: use demuxer for I2C4
  ARM: dts: koelsch: use demuxer for I2C2
  ARM: dts: lager: use demuxer for IIC3/I2C3
  ARM: dts: lager: use demuxer for IIC2/I2C2
  ARM: dts: r8a7745: Add VSP support
  ARM: dts: r8a7743: Add VSP support
  ARM: dts: r8a7745: Add IPMMU DT nodes
  ARM: dts: r8a7743: Add IPMMU DT nodes
  ARM: dts: r8a7745: sort subnodes of soc node
  ...

1 files changed, 1 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 936c5ff..9be131b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -797,6 +797,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
 	r8a7778-bockw.dtb \
 	r8a7779-marzen.dtb \
 	r8a7790-lager.dtb \
+	r8a7790-stout.dtb \
 	r8a7791-koelsch.dtb \
 	r8a7791-porter.dtb \
 	r8a7792-blanche.dtb \