Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 209 insertions, 0 deletions

diff --git a/arch/alpha/kernel/pci_impl.h b/arch/alpha/kernel/pci_impl.h
new file mode 100644
index 0000000..f8b7499
--- /dev/null
+++ b/arch/alpha/kernel/pci_impl.h
@@ -0,0 +1,209 @@
+/*
+ *	linux/arch/alpha/kernel/pci_impl.h
+ *
+ * This file contains declarations and inline functions for interfacing
+ * with the PCI initialization routines.
+ */
+
+struct pci_dev;
+struct pci_controller;
+struct pci_iommu_arena;
+
+/*
+ * We can't just blindly use 64K for machines with EISA busses; they
+ * may also have PCI-PCI bridges present, and then we'd configure the
+ * bridge incorrectly.
+ *
+ * Also, we start at 0x8000 or 0x9000, in hopes to get all devices'
+ * IO space areas allocated *before* 0xC000; this is because certain
+ * BIOSes (Millennium for one) use PCI Config space "mechanism #2"
+ * accesses to probe the bus. If a device's registers appear at 0xC000,
+ * it may see an INx/OUTx at that address during BIOS emulation of the
+ * VGA BIOS, and some cards, notably Adaptec 2940UW, take mortal offense.
+ */
+
+#define EISA_DEFAULT_IO_BASE	0x9000	/* start above 8th slot */
+#define DEFAULT_IO_BASE		0x8000	/* start at 8th slot */
+
+/*
+ * We try to make the DEFAULT_MEM_BASE addresses *always* have more than
+ * a single bit set. This is so that devices like the broken Myrinet card
+ * will always have a PCI memory address that will never match a IDSEL
+ * address in PCI Config space, which can cause problems with early rev cards.
+ */
+
+/*
+ * An XL is AVANTI (APECS) family, *but* it has only 27 bits of ISA address
+ * that get passed through the PCI<->ISA bridge chip. Although this causes
+ * us to set the PCI->Mem window bases lower than normal, we still allocate
+ * PCI bus devices' memory addresses *below* the low DMA mapping window,
+ * and hope they fit below 64Mb (to avoid conflicts), and so that they can
+ * be accessed via SPARSE space.
+ *
+ * We accept the risk that a broken Myrinet card will be put into a true XL
+ * and thus can more easily run into the problem described below.
+ */
+#define XL_DEFAULT_MEM_BASE ((16+2)*1024*1024) /* 16M to 64M-1 is avail */
+
+/*
+ * APECS and LCA have only 34 bits for physical addresses, thus limiting PCI
+ * bus memory addresses for SPARSE access to be less than 128Mb.
+ */
+#define APECS_AND_LCA_DEFAULT_MEM_BASE ((16+2)*1024*1024)
+
+/*
+ * Because MCPCIA and T2 core logic support more bits for
+ * physical addresses, they should allow an expanded range of SPARSE
+ * memory addresses.  However, we do not use them all, in order to
+ * avoid the HAE manipulation that would be needed.
+ */
+#define MCPCIA_DEFAULT_MEM_BASE ((32+2)*1024*1024)
+#define T2_DEFAULT_MEM_BASE ((16+1)*1024*1024)
+
+/*
+ * Because CIA and PYXIS have more bits for physical addresses,
+ * they support an expanded range of SPARSE memory addresses.
+ */
+#define DEFAULT_MEM_BASE ((128+16)*1024*1024)
+
+/* ??? Experimenting with no HAE for CIA.  */
+#define CIA_DEFAULT_MEM_BASE ((32+2)*1024*1024)
+
+#define IRONGATE_DEFAULT_MEM_BASE ((256*8-16)*1024*1024)
+
+#define DEFAULT_AGP_APER_SIZE	(64*1024*1024)
+
+/* 
+ * A small note about bridges and interrupts.  The DECchip 21050 (and
+ * later) adheres to the PCI-PCI bridge specification.  This says that
+ * the interrupts on the other side of a bridge are swizzled in the
+ * following manner:
+ *
+ * Dev    Interrupt   Interrupt 
+ *        Pin on      Pin on 
+ *        Device      Connector
+ *
+ *   4    A           A
+ *        B           B
+ *        C           C
+ *        D           D
+ * 
+ *   5    A           B
+ *        B           C
+ *        C           D
+ *        D           A
+ *
+ *   6    A           C
+ *        B           D
+ *        C           A
+ *        D           B
+ *
+ *   7    A           D
+ *        B           A
+ *        C           B
+ *        D           C
+ *
+ *   Where A = pin 1, B = pin 2 and so on and pin=0 = default = A.
+ *   Thus, each swizzle is ((pin-1) + (device#-4)) % 4
+ *
+ *   The following code swizzles for exactly one bridge.  The routine
+ *   common_swizzle below handles multiple bridges.  But there are a
+ *   couple boards that do strange things, so we define this here.
+ */
+
+static inline u8 bridge_swizzle(u8 pin, u8 slot) 
+{
+	return (((pin-1) + slot) % 4) + 1;
+}
+
+
+/* The following macro is used to implement the table-based irq mapping
+   function for all single-bus Alphas.  */
+
+#define COMMON_TABLE_LOOKUP						\
+({ long _ctl_ = -1; 							\
+   if (slot >= min_idsel && slot <= max_idsel && pin < irqs_per_slot)	\
+     _ctl_ = irq_tab[slot - min_idsel][pin];				\
+   _ctl_; })
+
+
+/* A PCI IOMMU allocation arena.  There are typically two of these
+   regions per bus.  */
+/* ??? The 8400 has a 32-byte pte entry, and the entire table apparently
+   lives directly on the host bridge (no tlb?).  We don't support this
+   machine, but if we ever did, we'd need to parameterize all this quite
+   a bit further.  Probably with per-bus operation tables.  */
+
+struct pci_iommu_arena
+{
+	spinlock_t lock;
+	struct pci_controller *hose;
+#define IOMMU_INVALID_PTE 0x2 /* 32:63 bits MBZ */
+#define IOMMU_RESERVED_PTE 0xface
+	unsigned long *ptes;
+	dma_addr_t dma_base;
+	unsigned int size;
+	unsigned int next_entry;
+	unsigned int align_entry;
+};
+
+#if defined(CONFIG_ALPHA_SRM) && \
+    (defined(CONFIG_ALPHA_CIA) || defined(CONFIG_ALPHA_LCA))
+# define NEED_SRM_SAVE_RESTORE
+#else
+# undef NEED_SRM_SAVE_RESTORE
+#endif
+
+#if defined(CONFIG_ALPHA_GENERIC) || defined(NEED_SRM_SAVE_RESTORE)
+# define ALPHA_RESTORE_SRM_SETUP
+#else
+# undef ALPHA_RESTORE_SRM_SETUP
+#endif
+
+#ifdef ALPHA_RESTORE_SRM_SETUP
+/* Store PCI device configuration left by SRM here. */
+struct pdev_srm_saved_conf
+{
+	struct pdev_srm_saved_conf *next;
+	struct pci_dev *dev;
+};
+
+extern void pci_restore_srm_config(void);
+#else
+#define pdev_save_srm_config(dev)	do {} while (0)
+#define pci_restore_srm_config()	do {} while (0)
+#endif
+
+/* The hose list.  */
+extern struct pci_controller *hose_head, **hose_tail;
+extern struct pci_controller *pci_isa_hose;
+
+/* Indicate that we trust the console to configure things properly.  */
+extern int pci_probe_only;
+
+extern unsigned long alpha_agpgart_size;
+
+extern void common_init_pci(void);
+extern u8 common_swizzle(struct pci_dev *, u8 *);
+extern struct pci_controller *alloc_pci_controller(void);
+extern struct resource *alloc_resource(void);
+
+extern struct pci_iommu_arena *iommu_arena_new_node(int,
+						    struct pci_controller *,
+					            dma_addr_t, unsigned long,
+					            unsigned long);
+extern struct pci_iommu_arena *iommu_arena_new(struct pci_controller *,
+					       dma_addr_t, unsigned long,
+					       unsigned long);
+extern const char *const pci_io_names[];
+extern const char *const pci_mem_names[];
+extern const char pci_hae0_name[];
+
+extern unsigned long size_for_memory(unsigned long max);
+
+extern int iommu_reserve(struct pci_iommu_arena *, long, long);
+extern int iommu_release(struct pci_iommu_arena *, long, long);
+extern int iommu_bind(struct pci_iommu_arena *, long, long, unsigned long *);
+extern int iommu_unbind(struct pci_iommu_arena *, long, long);
+
+