Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd

Pull MTD updates from David Woodhouse:
 - Various cleanups especially in NAND tests
 - Add support for NAND flash on BCMA bus
 - DT support for sh_flctl and denali NAND drivers
 - Kill obsolete/superceded drivers (fortunet, nomadik_nand)
 - Fix JFFS2 locking bug in ENOMEM failure path
 - New SPI flash chips, as usual
 - Support writing in 'reliable mode' for DiskOnChip G4
 - Debugfs support in nandsim

* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
  mtd: nand: typo in nand_id_has_period() comments
  mtd: nand/gpio: use io{read,write}*_rep accessors
  mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
  mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
  mtd: nand/docg4: fix and improve read of factory bbt
  mtd: nand/docg4: reserve bb marker area in ecclayout
  mtd: nand/docg4: add support for writing in reliable mode
  mtd: mxc_nand: reorder part_probes to let cmdline override other sources
  mtd: mxc_nand: fix unbalanced clk_disable() in error path
  mtd: nandsim: Introduce debugfs infrastructure
  mtd: physmap_of: error checking to prevent a NULL pointer dereference
  mtg: docg3: potential divide by zero in doc_write_oob()
  mtd: bcm47xxnflash: writing support
  mtd: tests/read: initialize buffer for whole next page
  mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
  mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
  mtd: nand: onfi need to be probed in 8 bits mode
  mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
  mtd: nand: print flash size during detection
  mted: nand_wait_ready timeout fix
  ...

6 files changed, 117 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt
index 49fc7ad..3545ea7 100644
--- a/Documentation/devicetree/bindings/arm/davinci/nand.txt
+++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt
@@ -23,6 +23,9 @@ Recommended properties :
 - ti,davinci-nand-buswidth: buswidth 8 or 16
 - ti,davinci-nand-use-bbt: use flash based bad block table support.
 
+nand device bindings may contain additional sub-nodes describing
+partitions of the address space. See partition.txt for more detail.
+
 Example(da850 EVM ):
 nand_cs3@62000000 {
 	compatible = "ti,davinci-nand";
@@ -35,4 +38,9 @@ nand_cs3@62000000 {
 	ti,davinci-ecc-mode = "hw";
 	ti,davinci-ecc-bits = <4>;
 	ti,davinci-nand-use-bbt;
+
+	partition@180000 {
+		label = "ubifs";
+		reg = <0x180000 0x7e80000>;
+	};
 };
diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt
new file mode 100644
index 0000000..b04d03a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt
@@ -0,0 +1,23 @@
+* Denali NAND controller
+
+Required properties:
+  - compatible : should be "denali,denali-nand-dt"
+  - reg : should contain registers location and length for data and reg.
+  - reg-names: Should contain the reg names "nand_data" and "denali_reg"
+  - interrupts : The interrupt number.
+  - dm-mask : DMA bit mask
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Examples:
+
+nand: nand@ff900000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "denali,denali-nand-dt";
+	reg = <0xff900000 0x100000>, <0xffb80000 0x10000>;
+	reg-names = "nand_data", "denali_reg";
+	interrupts = <0 144 4>;
+	dma-mask = <0xffffffff>;
+};
diff --git a/Documentation/devicetree/bindings/mtd/flctl-nand.txt b/Documentation/devicetree/bindings/mtd/flctl-nand.txt
new file mode 100644
index 0000000..427f46d
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/flctl-nand.txt
@@ -0,0 +1,49 @@
+FLCTL NAND controller
+
+Required properties:
+- compatible : "renesas,shmobile-flctl-sh7372"
+- reg : Address range of the FLCTL
+- interrupts : flste IRQ number
+- nand-bus-width : bus width to NAND chip
+
+Optional properties:
+- dmas: DMA specifier(s)
+- dma-names: name for each DMA specifier. Valid names are
+	     "data_tx", "data_rx", "ecc_tx", "ecc_rx"
+
+The DMA fields are not used yet in the driver but are listed here for
+completing the bindings.
+
+The device tree may optionally contain sub-nodes describing partitions of the
+address space. See partition.txt for more detail.
+
+Example:
+
+	flctl@e6a30000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "renesas,shmobile-flctl-sh7372";
+		reg = <0xe6a30000 0x100>;
+		interrupts = <0x0d80>;
+
+		nand-bus-width = <16>;
+
+		dmas = <&dmac 1 /* data_tx */
+			&dmac 2;> /* data_rx */
+		dma-names = "data_tx", "data_rx";
+
+		system@0 {
+			label = "system";
+			reg = <0x0 0x8000000>;
+		};
+
+		userdata@8000000 {
+			label = "userdata";
+			reg = <0x8000000 0x10000000>;
+		};
+
+		cache@18000000 {
+			label = "cache";
+			reg = <0x18000000 0x8000000>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
index e2c663b..e3ea32e 100644
--- a/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/fsmc-nand.txt
@@ -3,9 +3,7 @@
 Required properties:
 - compatible : "st,spear600-fsmc-nand"
 - reg : Address range of the mtd chip
-- reg-names: Should contain the reg names "fsmc_regs" and "nand_data"
-- st,ale-off : Chip specific offset to ALE
-- st,cle-off : Chip specific offset to CLE
+- reg-names: Should contain the reg names "fsmc_regs", "nand_data", "nand_addr" and "nand_cmd"
 
 Optional properties:
 - bank-width : Width (in bytes) of the device.  If not present, the width
@@ -19,10 +17,10 @@ Example:
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0xd1800000 0x1000	/* FSMC Register */
-		       0xd2000000 0x4000>;	/* NAND Base */
-		reg-names = "fsmc_regs", "nand_data";
-		st,ale-off = <0x20000>;
-		st,cle-off = <0x10000>;
+		       0xd2000000 0x0010	/* NAND Base DATA */
+		       0xd2020000 0x0010	/* NAND Base ADDR */
+		       0xd2010000 0x0010>;	/* NAND Base CMD */
+		reg-names = "fsmc_regs", "nand_data", "nand_addr", "nand_cmd";
 
 		bank-width = <1>;
 		nand-skip-bbtscan;
diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/m25p80.txt
new file mode 100644
index 0000000..6d3d576
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/m25p80.txt
@@ -0,0 +1,29 @@
+* MTD SPI driver for ST M25Pxx (and similar) serial flash chips
+
+Required properties:
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- compatible : Should be the manufacturer and the name of the chip. Bear in mind
+               the DT binding is not Linux-only, but in case of Linux, see the
+               "m25p_ids" table in drivers/mtd/devices/m25p80.c for the list of
+               supported chips.
+- reg : Chip-Select number
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
+
+Optional properties:
+- m25p,fast-read : Use the "fast read" opcode to read data from the chip instead
+                   of the usual "read" opcode. This opcode is not supported by
+                   all chips and support for it can not be detected at runtime.
+                   Refer to your chips' datasheet to check if this is supported
+                   by your chip.
+
+Example:
+
+	flash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spansion,m25p80";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+		m25p,fast-read;
+	};
diff --git a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
index 94de19b..dab7847 100644
--- a/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+++ b/Documentation/devicetree/bindings/mtd/mtd-physmap.txt
@@ -23,6 +23,9 @@ file systems on embedded devices.
    unaligned accesses as implemented in the JFFS2 code via memcpy().
    By defining "no-unaligned-direct-access", the flash will not be
    exposed directly to the MTD users (e.g. JFFS2) any more.
+ - linux,mtd-name: allow to specify the mtd name for retro capability with
+   physmap-flash drivers as boot loader pass the mtd partition via the old
+   device name physmap-flash.
 
 For JEDEC compatible devices, the following additional properties
 are defined: