Merge branch 'linux-2.6'

10 files changed, 48 insertions, 40 deletions

diff --git a/Documentation/DocBook/kgdb.tmpl b/Documentation/DocBook/kgdb.tmpl
index 028a844..e8acd1f 100644
--- a/Documentation/DocBook/kgdb.tmpl
+++ b/Documentation/DocBook/kgdb.tmpl
@@ -84,10 +84,9 @@
     runs an instance of gdb against the vmlinux file which contains
     the symbols (not boot image such as bzImage, zImage, uImage...).
     In gdb the developer specifies the connection parameters and
-    connects to kgdb.  Depending on which kgdb I/O modules exist in
-    the kernel for a given architecture, it may be possible to debug
-    the test machine's kernel with the development machine using a
-    rs232 or ethernet connection.
+    connects to kgdb.  The type of connection a developer makes with
+    gdb depends on the availability of kgdb I/O modules compiled as
+    builtin's or kernel modules in the test machine's kernel.
     </para>
   </chapter>
   <chapter id="CompilingAKernel">
@@ -223,7 +222,7 @@
   </para>
   <para>
   IMPORTANT NOTE: Using this option with kgdb over the console
-  (kgdboc) or kgdb over ethernet (kgdboe) is not supported.
+  (kgdboc) is not supported.
   </para>
   </sect1>
   </chapter>
@@ -249,18 +248,11 @@
     (gdb) target remote /dev/ttyS0
     </programlisting>
     <para>
-    Example (kgdb to a terminal server):
+    Example (kgdb to a terminal server on tcp port 2012):
     </para>
     <programlisting>
     % gdb ./vmlinux
-    (gdb) target remote udp:192.168.2.2:6443
-    </programlisting>
-    <para>
-    Example (kgdb over ethernet):
-    </para>
-    <programlisting>
-    % gdb ./vmlinux
-    (gdb) target remote udp:192.168.2.2:6443
+    (gdb) target remote 192.168.2.2:2012
     </programlisting>
     <para>
     Once connected, you can debug a kernel the way you would debug an
diff --git a/Documentation/cciss.txt b/Documentation/cciss.txt
index e65736c..63e59b8 100644
--- a/Documentation/cciss.txt
+++ b/Documentation/cciss.txt
@@ -21,6 +21,11 @@ This driver is known to work with the following cards:
 	* SA E200
 	* SA E200i
 	* SA E500
+	* SA P212
+	* SA P410
+	* SA P410i
+	* SA P411
+	* SA P812
 
 Detecting drive failures:
 -------------------------
diff --git a/Documentation/cpusets.txt b/Documentation/cpusets.txt
index d803c5c..353504d 100644
--- a/Documentation/cpusets.txt
+++ b/Documentation/cpusets.txt
@@ -542,7 +542,7 @@ otherwise initial value -1 that indicates the cpuset has no request.
    2  : search cores in a package.
    3  : search cpus in a node [= system wide on non-NUMA system]
  ( 4  : search nodes in a chunk of node [on NUMA system] )
- ( 5~ : search system wide [on NUMA system])
+ ( 5  : search system wide [on NUMA system] )
 
 This file is per-cpuset and affect the sched domain where the cpuset
 belongs to.  Therefore if the flag 'sched_load_balance' of a cpuset
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index 5b3f31f..46ece3f 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -312,3 +312,12 @@ When:	2.6.26
 Why:	Implementation became generic; users should now include
 	linux/semaphore.h instead.
 Who:	Matthew Wilcox <willy@linux.intel.com>
+
+---------------------------
+
+What:	CONFIG_THERMAL_HWMON
+When:	January 2009
+Why:	This option was introduced just to allow older lm-sensors userspace
+	to keep working over the upgrade to 2.6.26. At the scheduled time of
+	removal fixed lm-sensors (2.x or 3.x) should be readily available.
+Who:	Rene Herman <rene.herman@gmail.com>
diff --git a/Documentation/filesystems/ext4.txt b/Documentation/filesystems/ext4.txt
index 560f88d..0c5086db 100644
--- a/Documentation/filesystems/ext4.txt
+++ b/Documentation/filesystems/ext4.txt
@@ -139,8 +139,16 @@ commit=nrsec	(*)	Ext4 can be told to sync all its data and metadata
 			Setting it to very large values will improve
 			performance.
 
-barrier=1		This enables/disables barriers.  barrier=0 disables
-			it, barrier=1 enables it.
+barrier=<0|1(*)>	This enables/disables the use of write barriers in
+			the jbd code.  barrier=0 disables, barrier=1 enables.
+			This also requires an IO stack which can support
+			barriers, and if jbd gets an error on a barrier
+			write, it will disable again with a warning.
+			Write barriers enforce proper on-disk ordering
+			of journal commits, making volatile disk write caches
+			safe to use, at some performance penalty.  If
+			your disks are battery-backed in one way or another,
+			disabling barriers may safely improve performance.
 
 orlov		(*)	This enables the new Orlov block allocator. It is
 			enabled by default.
diff --git a/Documentation/filesystems/sysfs-pci.txt b/Documentation/filesystems/sysfs-pci.txt
index 5daa2aa..68ef488 100644
--- a/Documentation/filesystems/sysfs-pci.txt
+++ b/Documentation/filesystems/sysfs-pci.txt
@@ -36,6 +36,7 @@ files, each with their own function.
        local_cpus	   nearby CPU mask (cpumask, ro)
        resource		   PCI resource host addresses (ascii, ro)
        resource0..N	   PCI resource N, if present (binary, mmap)
+       resource0_wc..N_wc  PCI WC map resource N, if prefetchable (binary, mmap)
        rom		   PCI ROM resource, if present (binary, ro)
        subsystem_device	   PCI subsystem device (ascii, ro)
        subsystem_vendor	   PCI subsystem vendor (ascii, ro)
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index f4a8ebc..2d84573 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -2,17 +2,12 @@ Naming and data format standards for sysfs files
 ------------------------------------------------
 
 The libsensors library offers an interface to the raw sensors data
-through the sysfs interface. See libsensors documentation and source for
-further information. As of writing this document, libsensors
-(from lm_sensors 2.8.3) is heavily chip-dependent. Adding or updating
-support for any given chip requires modifying the library's code.
-This is because libsensors was written for the procfs interface
-older kernel modules were using, which wasn't standardized enough.
-Recent versions of libsensors (from lm_sensors 2.8.2 and later) have
-support for the sysfs interface, though.
-
-The new sysfs interface was designed to be as chip-independent as
-possible.
+through the sysfs interface. Since lm-sensors 3.0.0, libsensors is
+completely chip-independent. It assumes that all the kernel drivers
+implement the standard sysfs interface described in this document.
+This makes adding or updating support for any given chip very easy, as
+libsensors, and applications using it, do not need to be modified.
+This is a major improvement compared to lm-sensors 2.
 
 Note that motherboards vary widely in the connections to sensor chips.
 There is no standard that ensures, for example, that the second
@@ -35,19 +30,17 @@ access this data in a simple and consistent way. That said, such programs
 will have to implement conversion, labeling and hiding of inputs. For
 this reason, it is still not recommended to bypass the library.
 
-If you are developing a userspace application please send us feedback on
-this standard.
-
-Note that this standard isn't completely established yet, so it is subject
-to changes. If you are writing a new hardware monitoring driver those
-features can't seem to fit in this interface, please contact us with your
-extension proposal. Keep in mind that backward compatibility must be
-preserved.
-
 Each chip gets its own directory in the sysfs /sys/devices tree.  To
 find all sensor chips, it is easier to follow the device symlinks from
 /sys/class/hwmon/hwmon*.
 
+Up to lm-sensors 3.0.0, libsensors looks for hardware monitoring attributes
+in the "physical" device directory. Since lm-sensors 3.0.1, attributes found
+in the hwmon "class" device directory are also supported. Complex drivers
+(e.g. drivers for multifunction chips) may want to use this possibility to
+avoid namespace pollution. The only drawback will be that older versions of
+libsensors won't support the driver in question.
+
 All sysfs values are fixed point numbers.
 
 There is only one value per file, unlike the older /proc specification.
diff --git a/Documentation/kobject.txt b/Documentation/kobject.txt
index bf3256e..51a8021 100644
--- a/Documentation/kobject.txt
+++ b/Documentation/kobject.txt
@@ -305,7 +305,7 @@ should not be manipulated by any other user.
 
 A kset keeps its children in a standard kernel linked list.  Kobjects point
 back to their containing kset via their kset field. In almost all cases,
-the kobjects belonging to a ket have that kset (or, strictly, its embedded
+the kobjects belonging to a kset have that kset (or, strictly, its embedded
 kobject) in their parent.
 
 As a kset contains a kobject within it, it should always be dynamically
diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt
index 01c6c3d..64b3f14 100644
--- a/Documentation/laptops/thinkpad-acpi.txt
+++ b/Documentation/laptops/thinkpad-acpi.txt
@@ -503,7 +503,7 @@ generate input device EV_KEY events.
 In addition to the EV_KEY events, thinkpad-acpi may also issue EV_SW
 events for switches:
 
-SW_RADIO	T60 and later hardare rfkill rocker switch
+SW_RFKILL_ALL	T60 and later hardare rfkill rocker switch
 SW_TABLET_MODE	Tablet ThinkPads HKEY events 0x5009 and 0x500A
 
 Non hot-key ACPI HKEY event map:
diff --git a/Documentation/video4linux/CARDLIST.au0828 b/Documentation/video4linux/CARDLIST.au0828
index aaae360..86d1c8e 100644
--- a/Documentation/video4linux/CARDLIST.au0828
+++ b/Documentation/video4linux/CARDLIST.au0828
@@ -1,4 +1,4 @@
   0 -> Unknown board                            (au0828)
-  1 -> Hauppauge HVR950Q                        (au0828)        [2040:7200]
+  1 -> Hauppauge HVR950Q                        (au0828)        [2040:7200,2040:7210,2040:7217,2040:721b,2040:721f,2040:7280,0fd9:0008]
   2 -> Hauppauge HVR850                         (au0828)        [2040:7240]
   3 -> DViCO FusionHDTV USB                     (au0828)        [0fe9:d620]