trivial: fix then -> than typos in comments and documentation

- (better, more, bigger ...) then -> (...) than

Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

3 files changed, 5 insertions, 5 deletions

diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet
index aef5a9b..4d184f2 100644
--- a/Documentation/hwmon/abituguru-datasheet
+++ b/Documentation/hwmon/abituguru-datasheet
@@ -74,7 +74,7 @@ a sensor.
 Notice that some banks have both a read and a write address this is how the
 uGuru determines if a read from or a write to the bank is taking place, thus
 when reading you should always use the read address and when writing the
-write address. The write address is always one (1) more then the read address.
+write address. The write address is always one (1) more than the read address.
 
 
 uGuru ready
@@ -224,7 +224,7 @@ Bit 3: Beep if alarm							(RW)
 Bit 4: 1 if alarm cause measured temp is over the warning threshold	(R)
 Bit 5: 1 if alarm cause measured volt is over the max threshold		(R)
 Bit 6: 1 if alarm cause measured volt is under the min threshold	(R)
-Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds	(RW)
        Temp sensor: Shutdown if temp is over the shutdown threshold	(RW)
 
 *  This bit is only honored/used by the uGuru if a temp sensor is connected
@@ -293,7 +293,7 @@ Byte 0:
 Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
 Bit 0: Give an alarm if measured rpm is under the min threshold	(RW)
 Bit 3: Beep if alarm						(RW)
-Bit 7: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Shutdown if alarm persist for more than 4 seconds	(RW)
 
 Byte 1:
 min threshold (scale as bank 0x26)
diff --git a/Documentation/networking/rxrpc.txt b/Documentation/networking/rxrpc.txt
index c3669a3..60d05eb 100644
--- a/Documentation/networking/rxrpc.txt
+++ b/Documentation/networking/rxrpc.txt
@@ -540,7 +540,7 @@ A client would issue an operation by:
      MSG_MORE should be set in msghdr::msg_flags on all but the last part of
      the request.  Multiple requests may be made simultaneously.
 
-     If a call is intended to go to a destination other then the default
+     If a call is intended to go to a destination other than the default
      specified through connect(), then msghdr::msg_name should be set on the
      first request message of that call.
 
diff --git a/Documentation/scsi/ChangeLog.lpfc b/Documentation/scsi/ChangeLog.lpfc
index ae3f962a..ff19a52 100644
--- a/Documentation/scsi/ChangeLog.lpfc
+++ b/Documentation/scsi/ChangeLog.lpfc
@@ -733,7 +733,7 @@ Changes from 20040920 to 20041018
 	  I/O completion path a little more, especially taking care of
 	  fast-pathing the non-error case.  Also removes tons of dead
 	  members and defines from lpfc_scsi.h - e.g. lpfc_target is down
-	  to nothing more then the lpfc_nodelist pointer.
+	  to nothing more than the lpfc_nodelist pointer.
 	* Added binary sysfs file to issue mbox commands
 	* Replaced #if __BIG_ENDIAN with #if __BIG_ENDIAN_BITFIELD for
 	  compatibility with the user space applications.