[media] doc-rst: start adding documentation for cx2341x

move the contents of fw-decoder-api.txt to cx2341x and
convert it to ReST file, adding it to media/v4l-drivers

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

1 files changed, 0 insertions, 297 deletions

diff --git a/Documentation/video4linux/cx2341x/fw-decoder-api.txt b/Documentation/video4linux/cx2341x/fw-decoder-api.txt
deleted file mode 100644
index 8c317b7a..0000000
--- a/Documentation/video4linux/cx2341x/fw-decoder-api.txt
+++ /dev/null
@@ -1,297 +0,0 @@
-Decoder firmware API description
-================================
-
-Note: this API is part of the decoder firmware, so it's cx23415 only.
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_PING_FW
-Enum 	0/0x00
-Description
-	This API call does nothing. It may be used to check if the firmware
-	is responding.
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_START_PLAYBACK
-Enum 	1/0x01
-Description
-	Begin or resume playback.
-Param[0]
-	0 based frame number in GOP to begin playback from.
-Param[1]
-	Specifies the number of muted audio frames to play before normal
-	audio resumes. (This is not implemented in the firmware, leave at 0)
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_STOP_PLAYBACK
-Enum 	2/0x02
-Description
-	Ends playback and clears all decoder buffers. If PTS is not zero,
-	playback stops at specified PTS.
-Param[0]
-	Display 0=last frame, 1=black
-	Note: this takes effect immediately, so if you want to wait for a PTS,
-	then use '0', otherwise the screen goes to black at once.
-	You can call this later (even if there is no playback) with a 1 value
-	to set the screen to black.
-Param[1]
-	PTS low
-Param[2]
-	PTS high
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_PLAYBACK_SPEED
-Enum 	3/0x03
-Description
-	Playback stream at speed other than normal. There are two modes of
-	operation:
-	    Smooth: host transfers entire stream and firmware drops unused
-		    frames.
-	    Coarse: host drops frames based on indexing as required to achieve
-		    desired speed.
-Param[0]
-	Bitmap:
-	    0:7  0 normal
-		 1 fast only "1.5 times"
-		 n nX fast, 1/nX slow
-	    30   Framedrop:
-		     '0' during 1.5 times play, every other B frame is dropped
-		     '1' during 1.5 times play, stream is unchanged (bitrate
-			 must not exceed 8mbps)
-	    31   Speed:
-		     '0' slow
-		     '1' fast
-	Note: n is limited to 2. Anything higher does not result in
-	faster playback. Instead the host should start dropping frames.
-Param[1]
-	Direction: 0=forward, 1=reverse
-	Note: to make reverse playback work you have to write full GOPs in
-	reverse order.
-Param[2]
-	Picture mask:
-	    1=I frames
-	    3=I, P frames
-	    7=I, P, B frames
-Param[3]
-	B frames per GOP (for reverse play only)
-	Note: for reverse playback the Picture Mask should be set to I or I, P.
-	Adding B frames to the mask will result in corrupt video. This field
-	has to be set to the correct value in order to keep the timing correct.
-Param[4]
-	Mute audio: 0=disable, 1=enable
-Param[5]
-	Display 0=frame, 1=field
-Param[6]
-	Specifies the number of muted audio frames to play before normal audio
-	resumes. (Not implemented in the firmware, leave at 0)
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_STEP_VIDEO
-Enum 	5/0x05
-Description
-	Each call to this API steps the playback to the next unit defined below
-	in the current playback direction.
-Param[0]
-	0=frame, 1=top field, 2=bottom field
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_DMA_BLOCK_SIZE
-Enum 	8/0x08
-Description
-	Set DMA transfer block size. Counterpart to API 0xC9
-Param[0]
-	DMA transfer block size in bytes. A different size may be specified
-	when issuing the DMA transfer command.
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_GET_XFER_INFO
-Enum 	9/0x09
-Description
-	This API call may be used to detect an end of stream condition.
-Result[0]
-	Stream type
-Result[1]
-	Address offset
-Result[2]
-	Maximum bytes to transfer
-Result[3]
-	Buffer fullness
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_GET_DMA_STATUS
-Enum 	10/0x0A
-Description
-	Status of the last DMA transfer
-Result[0]
-	Bit 1 set means transfer complete
-	Bit 2 set means DMA error
-	Bit 3 set means linked list error
-Result[1]
-	DMA type: 0=MPEG, 1=OSD, 2=YUV
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SCHED_DMA_FROM_HOST
-Enum 	11/0x0B
-Description
-	Setup DMA from host operation. Counterpart to API 0xCC
-Param[0]
-	Memory address of link list
-Param[1]
-	Total # of bytes to transfer
-Param[2]
-	DMA type (0=MPEG, 1=OSD, 2=YUV)
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_PAUSE_PLAYBACK
-Enum 	13/0x0D
-Description
-	Freeze playback immediately. In this mode, when internal buffers are
-	full, no more data will be accepted and data request IRQs will be
-	masked.
-Param[0]
-	Display: 0=last frame, 1=black
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_HALT_FW
-Enum 	14/0x0E
-Description
-	The firmware is halted and no further API calls are serviced until
-	the firmware is uploaded again.
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_STANDARD
-Enum 	16/0x10
-Description
-	Selects display standard
-Param[0]
-	0=NTSC, 1=PAL
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_GET_VERSION
-Enum 	17/0x11
-Description
-	Returns decoder firmware version information
-Result[0]
-	Version bitmask:
-	    Bits  0:15 build
-	    Bits 16:23 minor
-	    Bits 24:31 major
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_STREAM_INPUT
-Enum 	20/0x14
-Description
-	Select decoder stream input port
-Param[0]
-	0=memory (default), 1=streaming
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_GET_TIMING_INFO
-Enum 	21/0x15
-Description
-	Returns timing information from start of playback
-Result[0]
-	Frame count by decode order
-Result[1]
-	Video PTS bits 0:31 by display order
-Result[2]
-	Video PTS bit 32 by display order
-Result[3]
-	SCR bits 0:31 by display order
-Result[4]
-	SCR bit 32 by display order
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_AUDIO_MODE
-Enum 	22/0x16
-Description
-	Select audio mode
-Param[0]
-	Dual mono mode action
-	    0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-Param[1]
-	Stereo mode action:
-	    0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_EVENT_NOTIFICATION
-Enum 	23/0x17
-Description
-	Setup firmware to notify the host about a particular event.
-	Counterpart to API 0xD5
-Param[0]
-	Event: 0=Audio mode change between mono, (joint) stereo and dual channel.
-	Event: 3=Decoder started
-	Event: 4=Unknown: goes off 10-15 times per second while decoding.
-	Event: 5=Some sync event: goes off once per frame.
-Param[1]
-	Notification 0=disabled, 1=enabled
-Param[2]
-	Interrupt bit
-Param[3]
-	Mailbox slot, -1 if no mailbox required.
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_DISPLAY_BUFFERS
-Enum 	24/0x18
-Description
-	Number of display buffers. To decode all frames in reverse playback you
-	must use nine buffers.
-Param[0]
-	0=six buffers, 1=nine buffers
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_EXTRACT_VBI
-Enum 	25/0x19
-Description
-	Extracts VBI data
-Param[0]
-	0=extract from extension & user data, 1=extract from private packets
-Result[0]
-	VBI table location
-Result[1]
-	VBI table size
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_DECODER_SOURCE
-Enum 	26/0x1A
-Description
-	Selects decoder source. Ensure that the parameters passed to this
-	API match the encoder settings.
-Param[0]
-	Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
-Param[1]
-	YUV picture width
-Param[2]
-	YUV picture height
-Param[3]
-	Bitmap: see Param[0] of API 0xBD
-
--------------------------------------------------------------------------------
-
-Name 	CX2341X_DEC_SET_PREBUFFERING
-Enum 	30/0x1E
-Description
-	Decoder prebuffering, when enabled up to 128KB are buffered for
-	streams <8mpbs or 640KB for streams >8mbps
-Param[0]
-	0=off, 1=on