Create/use more directory structure in the Documentation/ tree.

Create Documentation/blockdev/ sub-directory and populate it.
Populate the Documentation/serial/ sub-directory.
Move MSI-HOWTO.txt to Documentation/PCI/.
Move ioctl-number.txt to Documentation/ioctl/.
Update all relevant 00-INDEX files.
Update all relevant Kconfig files and source files.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>

1 files changed, 0 insertions, 292 deletions

diff --git a/Documentation/tty.txt b/Documentation/tty.txt
deleted file mode 100644
index 8e65c44..0000000
--- a/Documentation/tty.txt
+++ /dev/null
@@ -1,292 +0,0 @@
-
-			The Lockronomicon
-
-Your guide to the ancient and twisted locking policies of the tty layer and
-the warped logic behind them. Beware all ye who read on.
-
-FIXME: still need to work out the full set of BKL assumptions and document
-them so they can eventually be killed off.
-
-
-Line Discipline
----------------
-
-Line disciplines are registered with tty_register_ldisc() passing the
-discipline number and the ldisc structure. At the point of registration the 
-discipline must be ready to use and it is possible it will get used before
-the call returns success. If the call returns an error then it won't get
-called. Do not re-use ldisc numbers as they are part of the userspace ABI
-and writing over an existing ldisc will cause demons to eat your computer.
-After the return the ldisc data has been copied so you may free your own 
-copy of the structure. You must not re-register over the top of the line
-discipline even with the same data or your computer again will be eaten by
-demons.
-
-In order to remove a line discipline call tty_unregister_ldisc().
-In ancient times this always worked. In modern times the function will
-return -EBUSY if the ldisc is currently in use. Since the ldisc referencing
-code manages the module counts this should not usually be a concern.
-
-Heed this warning: the reference count field of the registered copies of the
-tty_ldisc structure in the ldisc table counts the number of lines using this
-discipline. The reference count of the tty_ldisc structure within a tty 
-counts the number of active users of the ldisc at this instant. In effect it
-counts the number of threads of execution within an ldisc method (plus those
-about to enter and exit although this detail matters not).
-
-Line Discipline Methods
------------------------
-
-TTY side interfaces:
-
-open()		-	Called when the line discipline is attached to
-			the terminal. No other call into the line
-			discipline for this tty will occur until it
-			completes successfully. Can sleep.
-
-close()		-	This is called on a terminal when the line
-			discipline is being unplugged. At the point of
-			execution no further users will enter the
-			ldisc code for this tty. Can sleep.
-
-hangup()	-	Called when the tty line is hung up.
-			The line discipline should cease I/O to the tty.
-			No further calls into the ldisc code will occur.
-			Can sleep.
-
-write()		-	A process is writing data through the line
-			discipline.  Multiple write calls are serialized
-			by the tty layer for the ldisc.  May sleep. 
-
-flush_buffer()	-	(optional) May be called at any point between
-			open and close, and instructs the line discipline
-			to empty its input buffer.
-
-chars_in_buffer() -	(optional) Report the number of bytes in the input
-			buffer.
-
-set_termios()	-	(optional) Called on termios structure changes.
-			The caller passes the old termios data and the
-			current data is in the tty. Called under the
-			termios semaphore so allowed to sleep. Serialized
-			against itself only.
-
-read()		-	Move data from the line discipline to the user.
-			Multiple read calls may occur in parallel and the
-			ldisc must deal with serialization issues. May 
-			sleep.
-
-poll()		-	Check the status for the poll/select calls. Multiple
-			poll calls may occur in parallel. May sleep.
-
-ioctl()		-	Called when an ioctl is handed to the tty layer
-			that might be for the ldisc. Multiple ioctl calls
-			may occur in parallel. May sleep. 
-
-Driver Side Interfaces:
-
-receive_buf()	-	Hand buffers of bytes from the driver to the ldisc
-			for processing. Semantics currently rather
-			mysterious 8(
-
-write_wakeup()	-	May be called at any point between open and close.
-			The TTY_DO_WRITE_WAKEUP flag indicates if a call
-			is needed but always races versus calls. Thus the
-			ldisc must be careful about setting order and to
-			handle unexpected calls. Must not sleep.
-
-			The driver is forbidden from calling this directly
-			from the ->write call from the ldisc as the ldisc
-			is permitted to call the driver write method from
-			this function. In such a situation defer it.
-
-
-Driver Access
-
-Line discipline methods can call the following methods of the underlying
-hardware driver through the function pointers within the tty->driver
-structure:
-
-write()			Write a block of characters to the tty device.
-			Returns the number of characters accepted. The
-			character buffer passed to this method is already
-			in kernel space.
-
-put_char()		Queues a character for writing to the tty device.
-			If there is no room in the queue, the character is
-			ignored.
-
-flush_chars()		(Optional) If defined, must be called after
-			queueing characters with put_char() in order to
-			start transmission.
-
-write_room()		Returns the numbers of characters the tty driver
-			will accept for queueing to be written.
-
-ioctl()			Invoke device specific ioctl.
-			Expects data pointers to refer to userspace.
-			Returns ENOIOCTLCMD for unrecognized ioctl numbers.
-
-set_termios()		Notify the tty driver that the device's termios
-			settings have changed. New settings are in
-			tty->termios. Previous settings should be passed in
-			the "old" argument.
-
-			The API is defined such that the driver should return
-			the actual modes selected. This means that the
-			driver function is responsible for modifying any
-			bits in the request it cannot fulfill to indicate
-			the actual modes being used. A device with no
-			hardware capability for change (eg a USB dongle or
-			virtual port) can provide NULL for this method.
-
-throttle()		Notify the tty driver that input buffers for the
-			line discipline are close to full, and it should
-			somehow signal that no more characters should be
-			sent to the tty.
-
-unthrottle()		Notify the tty driver that characters can now be
-			sent to the tty without fear of overrunning the
-			input buffers of the line disciplines.
-
-stop()			Ask the tty driver to stop outputting characters
-			to the tty device.
-
-start()			Ask the tty driver to resume sending characters
-			to the tty device.
-
-hangup()		Ask the tty driver to hang up the tty device.
-
-break_ctl()		(Optional) Ask the tty driver to turn on or off
-			BREAK status on the RS-232 port.  If state is -1,
-			then the BREAK status should be turned on; if
-			state is 0, then BREAK should be turned off.
-			If this routine is not implemented, use ioctls
-			TIOCSBRK / TIOCCBRK instead.
-
-wait_until_sent()	Waits until the device has written out all of the
-			characters in its transmitter FIFO.
-
-send_xchar()		Send a high-priority XON/XOFF character to the device.
-
-
-Flags
-
-Line discipline methods have access to tty->flags field containing the
-following interesting flags:
-
-TTY_THROTTLED		Driver input is throttled. The ldisc should call
-			tty->driver->unthrottle() in order to resume
-			reception when it is ready to process more data.
-
-TTY_DO_WRITE_WAKEUP	If set, causes the driver to call the ldisc's
-			write_wakeup() method in order to resume
-			transmission when it can accept more data
-			to transmit.
-
-TTY_IO_ERROR		If set, causes all subsequent userspace read/write
-			calls on the tty to fail, returning -EIO.
-
-TTY_OTHER_CLOSED	Device is a pty and the other side has closed.
-
-TTY_NO_WRITE_SPLIT	Prevent driver from splitting up writes into
-			smaller chunks.
-
-
-Locking
-
-Callers to the line discipline functions from the tty layer are required to
-take line discipline locks. The same is true of calls from the driver side
-but not yet enforced.
-
-Three calls are now provided
-
-	ldisc = tty_ldisc_ref(tty);
-
-takes a handle to the line discipline in the tty and returns it. If no ldisc
-is currently attached or the ldisc is being closed and re-opened at this
-point then NULL is returned. While this handle is held the ldisc will not
-change or go away.
-
-	tty_ldisc_deref(ldisc)
-
-Returns the ldisc reference and allows the ldisc to be closed. Returning the
-reference takes away your right to call the ldisc functions until you take
-a new reference.
-
-	ldisc = tty_ldisc_ref_wait(tty);
-
-Performs the same function as tty_ldisc_ref except that it will wait for an
-ldisc change to complete and then return a reference to the new ldisc. 
-
-While these functions are slightly slower than the old code they should have
-minimal impact as most receive logic uses the flip buffers and they only
-need to take a reference when they push bits up through the driver.
-
-A caution: The ldisc->open(), ldisc->close() and driver->set_ldisc 
-functions are called with the ldisc unavailable. Thus tty_ldisc_ref will
-fail in this situation if used within these functions. Ldisc and driver
-code calling its own functions must be careful in this case. 
-
-
-Driver Interface
-----------------
-
-open()		-	Called when a device is opened. May sleep
-
-close()		-	Called when a device is closed. At the point of
-			return from this call the driver must make no 
-			further ldisc calls of any kind. May sleep
-
-write()		-	Called to write bytes to the device. May not
-			sleep. May occur in parallel in special cases. 
-			Because this includes panic paths drivers generally
-			shouldn't try and do clever locking here.
-
-put_char()	-	Stuff a single character onto the queue. The
-			driver is guaranteed following up calls to
-			flush_chars.
-
-flush_chars()	-	Ask the kernel to write put_char queue
-
-write_room()	-	Return the number of characters tht can be stuffed
-			into the port buffers without overflow (or less).
-			The ldisc is responsible for being intelligent
- 			about multi-threading of write_room/write calls
-
-ioctl()		-	Called when an ioctl may be for the driver
-
-set_termios()	-	Called on termios change, serialized against
-			itself by a semaphore. May sleep.
-
-set_ldisc()	-	Notifier for discipline change. At the point this 
-			is done the discipline is not yet usable. Can now
-			sleep (I think)
-
-throttle()	-	Called by the ldisc to ask the driver to do flow
-			control.  Serialization including with unthrottle
-			is the job of the ldisc layer.
-
-unthrottle()	-	Called by the ldisc to ask the driver to stop flow
-			control.
-
-stop()		-	Ldisc notifier to the driver to stop output. As with
-			throttle the serializations with start() are down
-			to the ldisc layer.
-
-start()		-	Ldisc notifier to the driver to start output.
-
-hangup()	-	Ask the tty driver to cause a hangup initiated
-			from the host side. [Can sleep ??]
-
-break_ctl()	-	Send RS232 break. Can sleep. Can get called in
-			parallel, driver must serialize (for now), and
-			with write calls.
-
-wait_until_sent() -	Wait for characters to exit the hardware queue
-			of the driver. Can sleep
-
-send_xchar()	  -	Send XON/XOFF and if possible jump the queue with
-			it in order to get fast flow control responses.
-			Cannot sleep ??
-