ALSA: ISA: New Aztech Sound Galaxy driver

This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.

The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.

This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.

The drivers have been tested on various cards. For snd-azt1605:

FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II

and for snd-azt2316:

FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D

826 and 846 were also marketed directly by Aztech and then known as:

FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D

Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.

I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).

The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.

I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.

CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.

Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.

Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

1 files changed, 68 insertions, 0 deletions

diff --git a/Documentation/sound/alsa/ALSA-Configuration.txt b/Documentation/sound/alsa/ALSA-Configuration.txt
index 7f4dceb..e25555c 100644
--- a/Documentation/sound/alsa/ALSA-Configuration.txt
+++ b/Documentation/sound/alsa/ALSA-Configuration.txt
@@ -300,6 +300,74 @@ Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
            control correctly. If you have problems regarding this, try
            another ALSA compliant mixer (alsamixer works).
 
+  Module snd-azt1605
+  ------------------
+
+    Module for Aztech Sound Galaxy soundcards based on the Aztech AZT1605
+    chipset.
+
+    port	- port # for BASE (0x220,0x240,0x260,0x280)
+    wss_port	- port # for WSS (0x530,0x604,0xe80,0xf40)
+    irq		- IRQ # for WSS (7,9,10,11)
+    dma1	- DMA # for WSS playback (0,1,3)
+    dma2	- DMA # for WSS capture (0,1), -1 = disabled (default)
+    mpu_port	- port # for MPU-401 UART (0x300,0x330), -1 = disabled (default)
+    mpu_irq	- IRQ # for MPU-401 UART (3,5,7,9), -1 = disabled (default)
+    fm_port	- port # for OPL3 (0x388), -1 = disabled (default)
+
+    This module supports multiple cards. It does not support autoprobe: port,
+    wss_port, irq and dma1 have to be specified. The other values are
+    optional.
+
+    "port" needs to match the BASE ADDRESS jumper on the card (0x220 or 0x240)
+    or the value stored in the card's EEPROM for cards that have an EEPROM and
+    their "CONFIG MODE" jumper set to "EEPROM SETTING". The other values can
+    be choosen freely from the options enumerated above.
+
+    If dma2 is specified and different from dma1, the card will operate in
+    full-duplex mode. When dma1=3, only dma2=0 is valid and the only way to
+    enable capture since only channels 0 and 1 are available for capture.
+
+    Generic settings are "port=0x220 wss_port=0x530 irq=10 dma1=1 dma2=0
+    mpu_port=0x330 mpu_irq=9 fm_port=0x388".
+
+    Whatever IRQ and DMA channels you pick, be sure to reserve them for
+    legacy ISA in your BIOS.
+
+  Module snd-azt2316
+  ------------------
+
+    Module for Aztech Sound Galaxy soundcards based on the Aztech AZT2316
+    chipset.
+
+    port	- port # for BASE (0x220,0x240,0x260,0x280)
+    wss_port	- port # for WSS (0x530,0x604,0xe80,0xf40)
+    irq		- IRQ # for WSS (7,9,10,11)
+    dma1	- DMA # for WSS playback (0,1,3)
+    dma2	- DMA # for WSS capture (0,1), -1 = disabled (default)
+    mpu_port	- port # for MPU-401 UART (0x300,0x330), -1 = disabled (default)
+    mpu_irq	- IRQ # for MPU-401 UART (5,7,9,10), -1 = disabled (default)
+    fm_port	- port # for OPL3 (0x388), -1 = disabled (default)
+
+    This module supports multiple cards. It does not support autoprobe: port,
+    wss_port, irq and dma1 have to be specified. The other values are
+    optional.
+
+    "port" needs to match the BASE ADDRESS jumper on the card (0x220 or 0x240)
+    or the value stored in the card's EEPROM for cards that have an EEPROM and
+    their "CONFIG MODE" jumper set to "EEPROM SETTING". The other values can
+    be choosen freely from the options enumerated above.
+
+    If dma2 is specified and different from dma1, the card will operate in
+    full-duplex mode. When dma1=3, only dma2=0 is valid and the only way to
+    enable capture since only channels 0 and 1 are available for capture.
+
+    Generic settings are "port=0x220 wss_port=0x530 irq=10 dma1=1 dma2=0
+    mpu_port=0x330 mpu_irq=9 fm_port=0x388".
+
+    Whatever IRQ and DMA channels you pick, be sure to reserve them for
+    legacy ISA in your BIOS.
+
   Module snd-aw2
   --------------