dt: Move device tree documentation out of powerpc directory

The device tree is used by more than just PowerPC.  Make the documentation
directory available to all.

v2: reorganized files while moving to create arch and driver specific
    directories.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

1 files changed, 0 insertions, 70 deletions

diff --git a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt b/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
deleted file mode 100644
index e47734b..0000000
--- a/Documentation/powerpc/dts-bindings/fsl/cpm_qe/qe/ucc.txt
+++ /dev/null
@@ -1,70 +0,0 @@
-* UCC (Unified Communications Controllers)
-
-Required properties:
-- device_type : should be "network", "hldc", "uart", "transparent"
-  "bisync", "atm", or "serial".
-- compatible : could be "ucc_geth" or "fsl_atm" and so on.
-- cell-index : the ucc number(1-8), corresponding to UCCx in UM.
-- reg : Offset and length of the register set for the device
-- interrupts : <a b> where a is the interrupt number and b is a
-  field that represents an encoding of the sense and level
-  information for the interrupt.  This should be encoded based on
-  the information in section 2) depending on the type of interrupt
-  controller you have.
-- interrupt-parent : the phandle for the interrupt controller that
-  services interrupts for this device.
-- pio-handle : The phandle for the Parallel I/O port configuration.
-- port-number : for UART drivers, the port number to use, between 0 and 3.
-  This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
-  The port number is added to the minor number of the device.  Unlike the
-  CPM UART driver, the port-number is required for the QE UART driver.
-- soft-uart : for UART drivers, if specified this means the QE UART device
-  driver should use "Soft-UART" mode, which is needed on some SOCs that have
-  broken UART hardware.  Soft-UART is provided via a microcode upload.
-- rx-clock-name: the UCC receive clock source
-  "none": clock source is disabled
-  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
-  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
-- tx-clock-name: the UCC transmit clock source
-  "none": clock source is disabled
-  "brg1" through "brg16": clock source is BRG1-BRG16, respectively
-  "clk1" through "clk24": clock source is CLK1-CLK24, respectively
-The following two properties are deprecated.  rx-clock has been replaced
-with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
-Drivers that currently use the deprecated properties should continue to
-do so, in order to support older device trees, but they should be updated
-to check for the new properties first.
-- rx-clock : represents the UCC receive clock source.
-  0x00 : clock source is disabled;
-  0x1~0x10 : clock source is BRG1~BRG16 respectively;
-  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
-- tx-clock: represents the UCC transmit clock source;
-  0x00 : clock source is disabled;
-  0x1~0x10 : clock source is BRG1~BRG16 respectively;
-  0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
-
-Required properties for network device_type:
-- mac-address : list of bytes representing the ethernet address.
-- phy-handle : The phandle for the PHY connected to this controller.
-
-Recommended properties:
-- phy-connection-type : a string naming the controller/PHY interface type,
-  i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
-  Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
-  "tbi", or "rtbi".
-
-Example:
-	ucc@2000 {
-		device_type = "network";
-		compatible = "ucc_geth";
-		cell-index = <1>;
-		reg = <2000 200>;
-		interrupts = <a0 0>;
-		interrupt-parent = <700>;
-		mac-address = [ 00 04 9f 00 23 23 ];
-		rx-clock = "none";
-		tx-clock = "clk9";
-		phy-handle = <212000>;
-		phy-connection-type = "gmii";
-		pio-handle = <140001>;
-	};