summaryrefslogtreecommitdiffstats
path: root/Documentation/powerpc/booting-without-of.txt
diff options
context:
space:
mode:
authorDavid S. Miller <davem@davemloft.net>2008-07-18 02:39:39 -0700
committerDavid S. Miller <davem@davemloft.net>2008-07-18 02:39:39 -0700
commit49997d75152b3d23c53b0fa730599f2f74c92c65 (patch)
tree46e93126170d02cfec9505172e545732c1b69656 /Documentation/powerpc/booting-without-of.txt
parenta0c80b80e0fb48129e4e9d6a9ede914f9ff1850d (diff)
parent5b664cb235e97afbf34db9c4d77f08ebd725335e (diff)
downloadop-kernel-dev-49997d75152b3d23c53b0fa730599f2f74c92c65.zip
op-kernel-dev-49997d75152b3d23c53b0fa730599f2f74c92c65.tar.gz
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts: Documentation/powerpc/booting-without-of.txt drivers/atm/Makefile drivers/net/fs_enet/fs_enet-main.c drivers/pci/pci-acpi.c net/8021q/vlan.c net/iucv/iucv.c
Diffstat (limited to 'Documentation/powerpc/booting-without-of.txt')
-rw-r--r--Documentation/powerpc/booting-without-of.txt1025
1 files changed, 6 insertions, 1019 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index 46a9dba..aee243a 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -1247,80 +1247,7 @@ descriptions for the SOC devices for which new nodes have been
defined; this list will expand as more and more SOC-containing
platforms are moved over to use the flattened-device-tree model.
- a) MDIO IO device
-
- The MDIO is a bus to which the PHY devices are connected. For each
- device that exists on this bus, a child node should be created. See
- the definition of the PHY node below for an example of how to define
- a PHY.
-
- Required properties:
- - reg : Offset and length of the register set for the device
- - compatible : Should define the compatible device type for the
- mdio. Currently, this is most likely to be "fsl,gianfar-mdio"
-
- Example:
-
- mdio@24520 {
- reg = <24520 20>;
- compatible = "fsl,gianfar-mdio";
-
- ethernet-phy@0 {
- ......
- };
- };
-
-
- b) Gianfar-compatible ethernet nodes
-
- Required properties:
-
- - device_type : Should be "network"
- - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
- - compatible : Should be "gianfar"
- - reg : Offset and length of the register set for the device
- - mac-address : List of bytes representing the ethernet address of
- this controller
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - phy-handle : The phandle for the PHY connected to this ethernet
- controller.
- - fixed-link : <a b c d e> where a is emulated phy id - choose any,
- but unique to the all specified fixed-links, b is duplex - 0 half,
- 1 full, c is link speed - d#10/d#100/d#1000, d is pause - 0 no
- pause, 1 pause, e is asym_pause - 0 no asym_pause, 1 asym_pause.
-
- Recommended properties:
-
- - phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id", "sgmii",
- "tbi", or "rtbi". This property is only really needed if the connection
- is of type "rgmii-id", as all other connection types are detected by
- hardware.
-
-
- Example:
-
- ethernet@24000 {
- #size-cells = <0>;
- device_type = "network";
- model = "TSEC";
- compatible = "gianfar";
- reg = <24000 1000>;
- mac-address = [ 00 E0 0C 00 73 00 ];
- interrupts = <d 3 e 3 12 3>;
- interrupt-parent = <40000>;
- phy-handle = <2452000>
- };
-
-
-
- c) PHY nodes
+ a) PHY nodes
Required properties:
@@ -1348,7 +1275,7 @@ platforms are moved over to use the flattened-device-tree model.
};
- d) Interrupt controllers
+ b) Interrupt controllers
Some SOC devices contain interrupt controllers that are different
from the standard Open PIC specification. The SOC device nodes for
@@ -1361,491 +1288,14 @@ platforms are moved over to use the flattened-device-tree model.
pic@40000 {
linux,phandle = <40000>;
- clock-frequency = <0>;
interrupt-controller;
#address-cells = <0>;
reg = <40000 40000>;
- built-in;
compatible = "chrp,open-pic";
device_type = "open-pic";
- big-endian;
- };
-
-
- e) I2C
-
- Required properties :
-
- - device_type : Should be "i2c"
- - reg : Offset and length of the register set for the device
-
- Recommended properties :
-
- - compatible : Should be "fsl-i2c" for parts compatible with
- Freescale I2C specifications.
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - dfsrr : boolean; if defined, indicates that this I2C device has
- a digital filter sampling rate register
- - fsl5200-clocking : boolean; if defined, indicated that this device
- uses the FSL 5200 clocking mechanism.
-
- Example :
-
- i2c@3000 {
- interrupt-parent = <40000>;
- interrupts = <1b 3>;
- reg = <3000 18>;
- device_type = "i2c";
- compatible = "fsl-i2c";
- dfsrr;
- };
-
-
- f) Freescale SOC USB controllers
-
- The device node for a USB controller that is part of a Freescale
- SOC is as described in the document "Open Firmware Recommended
- Practice : Universal Serial Bus" with the following modifications
- and additions :
-
- Required properties :
- - compatible : Should be "fsl-usb2-mph" for multi port host USB
- controllers, or "fsl-usb2-dr" for dual role USB controllers
- - phy_type : For multi port host USB controllers, should be one of
- "ulpi", or "serial". For dual role USB controllers, should be
- one of "ulpi", "utmi", "utmi_wide", or "serial".
- - reg : Offset and length of the register set for the device
- - port0 : boolean; if defined, indicates port0 is connected for
- fsl-usb2-mph compatible controllers. Either this property or
- "port1" (or both) must be defined for "fsl-usb2-mph" compatible
- controllers.
- - port1 : boolean; if defined, indicates port1 is connected for
- fsl-usb2-mph compatible controllers. Either this property or
- "port0" (or both) must be defined for "fsl-usb2-mph" compatible
- controllers.
- - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible
- controllers. Can be "host", "peripheral", or "otg". Default to
- "host" if not defined for backward compatibility.
-
- Recommended properties :
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example multi port host USB controller device node :
- usb@22000 {
- compatible = "fsl-usb2-mph";
- reg = <22000 1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <700>;
- interrupts = <27 1>;
- phy_type = "ulpi";
- port0;
- port1;
};
- Example dual role USB controller device node :
- usb@23000 {
- compatible = "fsl-usb2-dr";
- reg = <23000 1000>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <700>;
- interrupts = <26 1>;
- dr_mode = "otg";
- phy = "ulpi";
- };
-
-
- g) Freescale SOC SEC Security Engines
-
- Required properties:
-
- - device_type : Should be "crypto"
- - model : Model of the device. Should be "SEC1" or "SEC2"
- - compatible : Should be "talitos"
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - num-channels : An integer representing the number of channels
- available.
- - channel-fifo-len : An integer representing the number of
- descriptor pointers each channel fetch fifo can hold.
- - exec-units-mask : The bitmask representing what execution units
- (EUs) are available. It's a single 32-bit cell. EU information
- should be encoded following the SEC's Descriptor Header Dword
- EU_SEL0 field documentation, i.e. as follows:
-
- bit 0 = reserved - should be 0
- bit 1 = set if SEC has the ARC4 EU (AFEU)
- bit 2 = set if SEC has the DES/3DES EU (DEU)
- bit 3 = set if SEC has the message digest EU (MDEU)
- bit 4 = set if SEC has the random number generator EU (RNG)
- bit 5 = set if SEC has the public key EU (PKEU)
- bit 6 = set if SEC has the AES EU (AESU)
- bit 7 = set if SEC has the Kasumi EU (KEU)
-
- bits 8 through 31 are reserved for future SEC EUs.
-
- - descriptor-types-mask : The bitmask representing what descriptors
- are available. It's a single 32-bit cell. Descriptor type
- information should be encoded following the SEC's Descriptor
- Header Dword DESC_TYPE field documentation, i.e. as follows:
-
- bit 0 = set if SEC supports the aesu_ctr_nonsnoop desc. type
- bit 1 = set if SEC supports the ipsec_esp descriptor type
- bit 2 = set if SEC supports the common_nonsnoop desc. type
- bit 3 = set if SEC supports the 802.11i AES ccmp desc. type
- bit 4 = set if SEC supports the hmac_snoop_no_afeu desc. type
- bit 5 = set if SEC supports the srtp descriptor type
- bit 6 = set if SEC supports the non_hmac_snoop_no_afeu desc.type
- bit 7 = set if SEC supports the pkeu_assemble descriptor type
- bit 8 = set if SEC supports the aesu_key_expand_output desc.type
- bit 9 = set if SEC supports the pkeu_ptmul descriptor type
- bit 10 = set if SEC supports the common_nonsnoop_afeu desc. type
- bit 11 = set if SEC supports the pkeu_ptadd_dbl descriptor type
-
- ..and so on and so forth.
-
- Example:
-
- /* MPC8548E */
- crypto@30000 {
- device_type = "crypto";
- model = "SEC2";
- compatible = "talitos";
- reg = <30000 10000>;
- interrupts = <1d 3>;
- interrupt-parent = <40000>;
- num-channels = <4>;
- channel-fifo-len = <18>;
- exec-units-mask = <000000fe>;
- descriptor-types-mask = <012b0ebf>;
- };
-
- h) Board Control and Status (BCSR)
-
- Required properties:
-
- - device_type : Should be "board-control"
- - reg : Offset and length of the register set for the device
-
- Example:
-
- bcsr@f8000000 {
- device_type = "board-control";
- reg = <f8000000 8000>;
- };
-
- i) Freescale QUICC Engine module (QE)
- This represents qe module that is installed on PowerQUICC II Pro.
-
- NOTE: This is an interim binding; it should be updated to fit
- in with the CPM binding later in this document.
-
- Basically, it is a bus of devices, that could act more or less
- as a complete entity (UCC, USB etc ). All of them should be siblings on
- the "root" qe node, using the common properties from there.
- The description below applies to the qe of MPC8360 and
- more nodes and properties would be extended in the future.
-
- i) Root QE device
-
- Required properties:
- - compatible : should be "fsl,qe";
- - model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
- - reg : offset and length of the device registers.
- - bus-frequency : the clock frequency for QUICC Engine.
-
- Recommended properties
- - brg-frequency : the internal clock source frequency for baud-rate
- generators in Hz.
-
- Example:
- qe@e0100000 {
- #address-cells = <1>;
- #size-cells = <1>;
- #interrupt-cells = <2>;
- compatible = "fsl,qe";
- ranges = <0 e0100000 00100000>;
- reg = <e0100000 480>;
- brg-frequency = <0>;
- bus-frequency = <179A7B00>;
- }
-
-
- ii) SPI (Serial Peripheral Interface)
-
- Required properties:
- - cell-index : SPI controller index.
- - compatible : should be "fsl,spi".
- - mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example:
- spi@4c0 {
- cell-index = <0>;
- compatible = "fsl,spi";
- reg = <4c0 40>;
- interrupts = <82 0>;
- interrupt-parent = <700>;
- mode = "cpu";
- };
-
-
- iii) USB (Universal Serial Bus Controller)
-
- Required properties:
- - compatible : could be "qe_udc" or "fhci-hcd".
- - mode : the could be "host" or "slave".
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example(slave):
- usb@6c0 {
- compatible = "qe_udc";
- reg = <6c0 40>;
- interrupts = <8b 0>;
- interrupt-parent = <700>;
- mode = "slave";
- };
-
-
- iv) UCC (Unified Communications Controllers)
-
- Required properties:
- - device_type : should be "network", "hldc", "uart", "transparent"
- "bisync", "atm", or "serial".
- - compatible : could be "ucc_geth" or "fsl_atm" and so on.
- - cell-index : the ucc number(1-8), corresponding to UCCx in UM.
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - pio-handle : The phandle for the Parallel I/O port configuration.
- - port-number : for UART drivers, the port number to use, between 0 and 3.
- This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
- The port number is added to the minor number of the device. Unlike the
- CPM UART driver, the port-number is required for the QE UART driver.
- - soft-uart : for UART drivers, if specified this means the QE UART device
- driver should use "Soft-UART" mode, which is needed on some SOCs that have
- broken UART hardware. Soft-UART is provided via a microcode upload.
- - rx-clock-name: the UCC receive clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
- - tx-clock-name: the UCC transmit clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
- The following two properties are deprecated. rx-clock has been replaced
- with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
- Drivers that currently use the deprecated properties should continue to
- do so, in order to support older device trees, but they should be updated
- to check for the new properties first.
- - rx-clock : represents the UCC receive clock source.
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
- - tx-clock: represents the UCC transmit clock source;
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
-
- Required properties for network device_type:
- - mac-address : list of bytes representing the ethernet address.
- - phy-handle : The phandle for the PHY connected to this controller.
-
- Recommended properties:
- - phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
- Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
- "tbi", or "rtbi".
-
- Example:
- ucc@2000 {
- device_type = "network";
- compatible = "ucc_geth";
- cell-index = <1>;
- reg = <2000 200>;
- interrupts = <a0 0>;
- interrupt-parent = <700>;
- mac-address = [ 00 04 9f 00 23 23 ];
- rx-clock = "none";
- tx-clock = "clk9";
- phy-handle = <212000>;
- phy-connection-type = "gmii";
- pio-handle = <140001>;
- };
-
-
- v) Parallel I/O Ports
-
- This node configures Parallel I/O ports for CPUs with QE support.
- The node should reside in the "soc" node of the tree. For each
- device that using parallel I/O ports, a child node should be created.
- See the definition of the Pin configuration nodes below for more
- information.
-
- Required properties:
- - device_type : should be "par_io".
- - reg : offset to the register set and its length.
- - num-ports : number of Parallel I/O ports
-
- Example:
- par_io@1400 {
- reg = <1400 100>;
- #address-cells = <1>;
- #size-cells = <0>;
- device_type = "par_io";
- num-ports = <7>;
- ucc_pin@01 {
- ......
- };
-
-
- vi) Pin configuration nodes
-
- Required properties:
- - linux,phandle : phandle of this node; likely referenced by a QE
- device.
- - pio-map : array of pin configurations. Each pin is defined by 6
- integers. The six numbers are respectively: port, pin, dir,
- open_drain, assignment, has_irq.
- - port : port number of the pin; 0-6 represent port A-G in UM.
- - pin : pin number in the port.
- - dir : direction of the pin, should encode as follows:
-
- 0 = The pin is disabled
- 1 = The pin is an output
- 2 = The pin is an input
- 3 = The pin is I/O
-
- - open_drain : indicates the pin is normal or wired-OR:
-
- 0 = The pin is actively driven as an output
- 1 = The pin is an open-drain driver. As an output, the pin is
- driven active-low, otherwise it is three-stated.
-
- - assignment : function number of the pin according to the Pin Assignment
- tables in User Manual. Each pin can have up to 4 possible functions in
- QE and two options for CPM.
- - has_irq : indicates if the pin is used as source of external
- interrupts.
-
- Example:
- ucc_pin@01 {
- linux,phandle = <140001>;
- pio-map = <
- /* port pin dir open_drain assignment has_irq */
- 0 3 1 0 1 0 /* TxD0 */
- 0 4 1 0 1 0 /* TxD1 */
- 0 5 1 0 1 0 /* TxD2 */
- 0 6 1 0 1 0 /* TxD3 */
- 1 6 1 0 3 0 /* TxD4 */
- 1 7 1 0 1 0 /* TxD5 */
- 1 9 1 0 2 0 /* TxD6 */
- 1 a 1 0 2 0 /* TxD7 */
- 0 9 2 0 1 0 /* RxD0 */
- 0 a 2 0 1 0 /* RxD1 */
- 0 b 2 0 1 0 /* RxD2 */
- 0 c 2 0 1 0 /* RxD3 */
- 0 d 2 0 1 0 /* RxD4 */
- 1 1 2 0 2 0 /* RxD5 */
- 1 0 2 0 2 0 /* RxD6 */
- 1 4 2 0 2 0 /* RxD7 */
- 0 7 1 0 1 0 /* TX_EN */
- 0 8 1 0 1 0 /* TX_ER */
- 0 f 2 0 1 0 /* RX_DV */
- 0 10 2 0 1 0 /* RX_ER */
- 0 0 2 0 1 0 /* RX_CLK */
- 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
- 2 8 2 0 1 0>; /* GTX125 - CLK9 */
- };
-
- vii) Multi-User RAM (MURAM)
-
- Required properties:
- - compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
- - mode : the could be "host" or "slave".
- - ranges : Should be defined as specified in 1) to describe the
- translation of MURAM addresses.
- - data-only : sub-node which defines the address area under MURAM
- bus that can be allocated as data/parameter
-
- Example:
-
- muram@10000 {
- compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0 00010000 0000c000>;
-
- data-only@0{
- compatible = "fsl,qe-muram-data",
- "fsl,cpm-muram-data";
- reg = <0 c000>;
- };
- };
-
- viii) Uploaded QE firmware
-
- If a new firwmare has been uploaded to the QE (usually by the
- boot loader), then a 'firmware' child node should be added to the QE
- node. This node provides information on the uploaded firmware that
- device drivers may need.
-
- Required properties:
- - id: The string name of the firmware. This is taken from the 'id'
- member of the qe_firmware structure of the uploaded firmware.
- Device drivers can search this string to determine if the
- firmware they want is already present.
- - extended-modes: The Extended Modes bitfield, taken from the
- firmware binary. It is a 64-bit number represented
- as an array of two 32-bit numbers.
- - virtual-traps: The virtual traps, taken from the firmware binary.
- It is an array of 8 32-bit numbers.
-
- Example:
-
- firmware {
- id = "Soft-UART";
- extended-modes = <0 0>;
- virtual-traps = <0 0 0 0 0 0 0 0>;
- }
-
- j) CFI or JEDEC memory-mapped NOR flash
+ c) CFI or JEDEC memory-mapped NOR flash
Flash chips (Memory Technology Devices) are often used for solid state
file systems on embedded devices.
@@ -1909,268 +1359,7 @@ platforms are moved over to use the flattened-device-tree model.
};
};
- k) Global Utilities Block
-
- The global utilities block controls power management, I/O device
- enabling, power-on-reset configuration monitoring, general-purpose
- I/O signal configuration, alternate function selection for multiplexed
- signals, and clock control.
-
- Required properties:
-
- - compatible : Should define the compatible device type for
- global-utilities.
- - reg : Offset and length of the register set for the device.
-
- Recommended properties:
-
- - fsl,has-rstcr : Indicates that the global utilities register set
- contains a functioning "reset control register" (i.e. the board
- is wired to reset upon setting the HRESET_REQ bit in this register).
-
- Example:
-
- global-utilities@e0000 { /* global utilities block */
- compatible = "fsl,mpc8548-guts";
- reg = <e0000 1000>;
- fsl,has-rstcr;
- };
-
- l) Freescale Communications Processor Module
-
- NOTE: This is an interim binding, and will likely change slightly,
- as more devices are supported. The QE bindings especially are
- incomplete.
-
- i) Root CPM node
-
- Properties:
- - compatible : "fsl,cpm1", "fsl,cpm2", or "fsl,qe".
- - reg : A 48-byte region beginning with CPCR.
-
- Example:
- cpm@119c0 {
- #address-cells = <1>;
- #size-cells = <1>;
- #interrupt-cells = <2>;
- compatible = "fsl,mpc8272-cpm", "fsl,cpm2";
- reg = <119c0 30>;
- }
-
- ii) Properties common to mulitple CPM/QE devices
-
- - fsl,cpm-command : This value is ORed with the opcode and command flag
- to specify the device on which a CPM command operates.
-
- - fsl,cpm-brg : Indicates which baud rate generator the device
- is associated with. If absent, an unused BRG
- should be dynamically allocated. If zero, the
- device uses an external clock rather than a BRG.
-
- - reg : Unless otherwise specified, the first resource represents the
- scc/fcc/ucc registers, and the second represents the device's
- parameter RAM region (if it has one).
-
- iii) Serial
-
- Currently defined compatibles:
- - fsl,cpm1-smc-uart
- - fsl,cpm2-smc-uart
- - fsl,cpm1-scc-uart
- - fsl,cpm2-scc-uart
- - fsl,qe-uart
-
- Example:
-
- serial@11a00 {
- device_type = "serial";
- compatible = "fsl,mpc8272-scc-uart",
- "fsl,cpm2-scc-uart";
- reg = <11a00 20 8000 100>;
- interrupts = <28 8>;
- interrupt-parent = <&PIC>;
- fsl,cpm-brg = <1>;
- fsl,cpm-command = <00800000>;
- };
-
- iii) Network
-
- Currently defined compatibles:
- - fsl,cpm1-scc-enet
- - fsl,cpm2-scc-enet
- - fsl,cpm1-fec-enet
- - fsl,cpm2-fcc-enet (third resource is GFEMR)
- - fsl,qe-enet
-
- Example:
-
- ethernet@11300 {
- device_type = "network";
- compatible = "fsl,mpc8272-fcc-enet",
- "fsl,cpm2-fcc-enet";
- reg = <11300 20 8400 100 11390 1>;
- local-mac-address = [ 00 00 00 00 00 00 ];
- interrupts = <20 8>;
- interrupt-parent = <&PIC>;
- phy-handle = <&PHY0>;
- fsl,cpm-command = <12000300>;
- };
-
- iv) MDIO
-
- Currently defined compatibles:
- fsl,pq1-fec-mdio (reg is same as first resource of FEC device)
- fsl,cpm2-mdio-bitbang (reg is port C registers)
-
- Properties for fsl,cpm2-mdio-bitbang:
- fsl,mdio-pin : pin of port C controlling mdio data
- fsl,mdc-pin : pin of port C controlling mdio clock
-
- Example:
-
- mdio@10d40 {
- device_type = "mdio";
- compatible = "fsl,mpc8272ads-mdio-bitbang",
- "fsl,mpc8272-mdio-bitbang",
- "fsl,cpm2-mdio-bitbang";
- reg = <10d40 14>;
- #address-cells = <1>;
- #size-cells = <0>;
- fsl,mdio-pin = <12>;
- fsl,mdc-pin = <13>;
- };
-
- v) Baud Rate Generators
-
- Currently defined compatibles:
- fsl,cpm-brg
- fsl,cpm1-brg
- fsl,cpm2-brg
-
- Properties:
- - reg : There may be an arbitrary number of reg resources; BRG
- numbers are assigned to these in order.
- - clock-frequency : Specifies the base frequency driving
- the BRG.
-
- Example:
-
- brg@119f0 {
- compatible = "fsl,mpc8272-brg",
- "fsl,cpm2-brg",
- "fsl,cpm-brg";
- reg = <119f0 10 115f0 10>;
- clock-frequency = <d#25000000>;
- };
-
- vi) Interrupt Controllers
-
- Currently defined compatibles:
- - fsl,cpm1-pic
- - only one interrupt cell
- - fsl,pq1-pic
- - fsl,cpm2-pic
- - second interrupt cell is level/sense:
- - 2 is falling edge
- - 8 is active low
-
- Example:
-
- interrupt-controller@10c00 {
- #interrupt-cells = <2>;
- interrupt-controller;
- reg = <10c00 80>;
- compatible = "mpc8272-pic", "fsl,cpm2-pic";
- };
-
- vii) USB (Universal Serial Bus Controller)
-
- Properties:
- - compatible : "fsl,cpm1-usb", "fsl,cpm2-usb", "fsl,qe-usb"
-
- Example:
- usb@11bc0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,cpm2-usb";
- reg = <11b60 18 8b00 100>;
- interrupts = <b 8>;
- interrupt-parent = <&PIC>;
- fsl,cpm-command = <2e600000>;
- };
-
- viii) Multi-User RAM (MURAM)
-
- The multi-user/dual-ported RAM is expressed as a bus under the CPM node.
-
- Ranges must be set up subject to the following restrictions:
-
- - Children's reg nodes must be offsets from the start of all muram, even
- if the user-data area does not begin at zero.
- - If multiple range entries are used, the difference between the parent
- address and the child address must be the same in all, so that a single
- mapping can cover them all while maintaining the ability to determine
- CPM-side offsets with pointer subtraction. It is recommended that
- multiple range entries not be used.
- - A child address of zero must be translatable, even if no reg resources
- contain it.
-
- A child "data" node must exist, compatible with "fsl,cpm-muram-data", to
- indicate the portion of muram that is usable by the OS for arbitrary
- purposes. The data node may have an arbitrary number of reg resources,
- all of which contribute to the allocatable muram pool.
-
- Example, based on mpc8272:
-
- muram@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0 10000>;
-
- data@0 {
- compatible = "fsl,cpm-muram-data";
- reg = <0 2000 9800 800>;
- };
- };
-
- m) Chipselect/Local Bus
-
- Properties:
- - name : Should be localbus
- - #address-cells : Should be either two or three. The first cell is the
- chipselect number, and the remaining cells are the
- offset into the chipselect.
- - #size-cells : Either one or two, depending on how large each chipselect
- can be.
- - ranges : Each range corresponds to a single chipselect, and cover
- the entire access window as configured.
-
- Example:
- localbus@f0010100 {
- compatible = "fsl,mpc8272-localbus",
- "fsl,pq2-localbus";
- #address-cells = <2>;
- #size-cells = <1>;
- reg = <f0010100 40>;
-
- ranges = <0 0 fe000000 02000000
- 1 0 f4500000 00008000>;
-
- flash@0,0 {
- compatible = "jedec-flash";
- reg = <0 0 2000000>;
- bank-width = <4>;
- device-width = <1>;
- };
-
- board-control@1,0 {
- reg = <1 0 20>;
- compatible = "fsl,mpc8272ads-bcsr";
- };
- };
-
-
- n) 4xx/Axon EMAC ethernet nodes
+ d) 4xx/Axon EMAC ethernet nodes
The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
the Axon bridge. To operate this needs to interact with a ths
@@ -2318,7 +1507,7 @@ platforms are moved over to use the flattened-device-tree model.
available.
For Axon: 0x0000012a
- o) Xilinx IP cores
+ e) Xilinx IP cores
The Xilinx EDK toolchain ships with a set of IP cores (devices) for use
in Xilinx Spartan and Virtex FPGAs. The devices cover the whole range
@@ -2612,206 +1801,7 @@ platforms are moved over to use the flattened-device-tree model.
- reg-offset : A value of 3 is required
- reg-shift : A value of 2 is required
-
- p) Freescale Synchronous Serial Interface
-
- The SSI is a serial device that communicates with audio codecs. It can
- be programmed in AC97, I2S, left-justified, or right-justified modes.
-
- Required properties:
- - compatible : compatible list, containing "fsl,ssi"
- - cell-index : the SSI, <0> = SSI1, <1> = SSI2, and so on
- - reg : offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and
- level information for the interrupt. This should be
- encoded based on the information in section 2)
- depending on the type of interrupt controller you
- have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - fsl,mode : the operating mode for the SSI interface
- "i2s-slave" - I2S mode, SSI is clock slave
- "i2s-master" - I2S mode, SSI is clock master
- "lj-slave" - left-justified mode, SSI is clock slave
- "lj-master" - l.j. mode, SSI is clock master
- "rj-slave" - right-justified mode, SSI is clock slave
- "rj-master" - r.j., SSI is clock master
- "ac97-slave" - AC97 mode, SSI is clock slave
- "ac97-master" - AC97 mode, SSI is clock master
-
- Optional properties:
- - codec-handle : phandle to a 'codec' node that defines an audio
- codec connected to this SSI. This node is typically
- a child of an I2C or other control node.
-
- Child 'codec' node required properties:
- - compatible : compatible list, contains the name of the codec
-
- Child 'codec' node optional properties:
- - clock-frequency : The frequency of the input clock, which typically
- comes from an on-board dedicated oscillator.
-
- * Freescale 83xx DMA Controller
-
- Freescale PowerPC 83xx have on chip general purpose DMA controllers.
-
- Required properties:
-
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma", where CHIP is the processor
- (mpc8349, mpc8360, etc.) and the second is
- "fsl,elo-dma"
- - reg : <registers mapping for DMA general status reg>
- - ranges : Should be defined as specified in 1) to describe the
- DMA controller channels.
- - cell-index : controller index. 0 for controller @ 0x8100
- - interrupts : <interrupt mapping for DMA IRQ>
- - interrupt-parent : optional, if needed for interrupt mapping
-
-
- - DMA channel nodes:
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma-channel", where CHIP is the processor
- (mpc8349, mpc8350, etc.) and the second is
- "fsl,elo-dma-channel"
- - reg : <registers mapping for channel>
- - cell-index : dma channel index starts at 0.
-
- Optional properties:
- - interrupts : <interrupt mapping for DMA channel IRQ>
- (on 83xx this is expected to be identical to
- the interrupts property of the parent node)
- - interrupt-parent : optional, if needed for interrupt mapping
-
- Example:
- dma@82a8 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8349-dma", "fsl,elo-dma";
- reg = <82a8 4>;
- ranges = <0 8100 1a4>;
- interrupt-parent = <&ipic>;
- interrupts = <47 8>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <0>;
- reg = <0 80>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <1>;
- reg = <80 80>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <2>;
- reg = <100 80>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8349-dma-channel", "fsl,elo-dma-channel";
- cell-index = <3>;
- reg = <180 80>;
- };
- };
-
- * Freescale 85xx/86xx DMA Controller
-
- Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers.
-
- Required properties:
-
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma", where CHIP is the processor
- (mpc8540, mpc8540, etc.) and the second is
- "fsl,eloplus-dma"
- - reg : <registers mapping for DMA general status reg>
- - cell-index : controller index. 0 for controller @ 0x21000,
- 1 for controller @ 0xc000
- - ranges : Should be defined as specified in 1) to describe the
- DMA controller channels.
-
- - DMA channel nodes:
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-dma-channel", where CHIP is the processor
- (mpc8540, mpc8560, etc.) and the second is
- "fsl,eloplus-dma-channel"
- - cell-index : dma channel index starts at 0.
- - reg : <registers mapping for channel>
- - interrupts : <interrupt mapping for DMA channel IRQ>
- - interrupt-parent : optional, if needed for interrupt mapping
-
- Example:
- dma@21300 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "fsl,mpc8540-dma", "fsl,eloplus-dma";
- reg = <21300 4>;
- ranges = <0 21100 200>;
- cell-index = <0>;
- dma-channel@0 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <0 80>;
- cell-index = <0>;
- interrupt-parent = <&mpic>;
- interrupts = <14 2>;
- };
- dma-channel@80 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <80 80>;
- cell-index = <1>;
- interrupt-parent = <&mpic>;
- interrupts = <15 2>;
- };
- dma-channel@100 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <100 80>;
- cell-index = <2>;
- interrupt-parent = <&mpic>;
- interrupts = <16 2>;
- };
- dma-channel@180 {
- compatible = "fsl,mpc8540-dma-channel", "fsl,eloplus-dma-channel";
- reg = <180 80>;
- cell-index = <3>;
- interrupt-parent = <&mpic>;
- interrupts = <17 2>;
- };
- };
-
- * Freescale 8xxx/3.0 Gb/s SATA nodes
-
- SATA nodes are defined to describe on-chip Serial ATA controllers.
- Each SATA port should have its own node.
-
- Required properties:
- - compatible : compatible list, contains 2 entries, first is
- "fsl,CHIP-sata", where CHIP is the processor
- (mpc8315, mpc8379, etc.) and the second is
- "fsl,pq-sata"
- - interrupts : <interrupt mapping for SATA IRQ>
- - cell-index : controller index.
- 1 for controller @ 0x18000
- 2 for controller @ 0x19000
- 3 for controller @ 0x1a000
- 4 for controller @ 0x1b000
-
- Optional properties:
- - interrupt-parent : optional, if needed for interrupt mapping
- - reg : <registers mapping>
-
- Example:
-
- sata@18000 {
- compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
- reg = <0x18000 0x1000>;
- cell-index = <1>;
- interrupts = <2c 8>;
- interrupt-parent = < &ipic >;
- };
-
- q) USB EHCI controllers
+ f) USB EHCI controllers
Required properties:
- compatible : should be "usb-ehci".
@@ -3643,14 +2633,11 @@ not necessary as they are usually the same as the root node.
pic@40000 {
linux,phandle = <40000>;
- clock-frequency = <0>;
interrupt-controller;
#address-cells = <0>;
reg = <40000 40000>;
- built-in;
compatible = "chrp,open-pic";
device_type = "open-pic";
- big-endian;
};
i2c@3000 {
OpenPOWER on IntegriCloud