summaryrefslogtreecommitdiffstats
path: root/Documentation/pinctrl.txt
diff options
context:
space:
mode:
authorLinus Walleij <linus.walleij@linaro.org>2013-06-25 16:17:15 +0200
committerLinus Walleij <linus.walleij@linaro.org>2013-07-23 01:23:14 +0200
commiteb6002d5e2eaf8b8c0ee11c8e47bbe7473b4c434 (patch)
tree34f41aa6aaedfc8392acd9c6cb8718ea1cee6cfa /Documentation/pinctrl.txt
parentad81f0545ef01ea651886dddac4bef6cec930092 (diff)
downloadop-kernel-dev-eb6002d5e2eaf8b8c0ee11c8e47bbe7473b4c434.zip
op-kernel-dev-eb6002d5e2eaf8b8c0ee11c8e47bbe7473b4c434.tar.gz
pinctrl: elaborate a bit on arrangements in doc
This elaborates a bit on the pin control and pin muxing logic vs GPIO arangements in the hardware. Inspired by some drawings in a mail from Christian Ruppert. Both arrangements are confirmed to exist in practice. Cc: Rob Landley <rob@landley.net> Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Diffstat (limited to 'Documentation/pinctrl.txt')
-rw-r--r--Documentation/pinctrl.txt91
1 files changed, 85 insertions, 6 deletions
diff --git a/Documentation/pinctrl.txt b/Documentation/pinctrl.txt
index 052e13a..d2d7fc0 100644
--- a/Documentation/pinctrl.txt
+++ b/Documentation/pinctrl.txt
@@ -795,18 +795,97 @@ special GPIO-handler is registered.
GPIO mode pitfalls
==================
-Sometime the developer may be confused by a datasheet talking about a pin
-being possible to set into "GPIO mode". It appears that what hardware
-engineers mean with "GPIO mode" is not necessarily the use case that is
-implied in the kernel interface <linux/gpio.h>: a pin that you grab from
-kernel code and then either listen for input or drive high/low to
-assert/deassert some external line.
+Due to the naming conventions used by hardware engineers, where "GPIO"
+is taken to mean different things than what the kernel does, the developer
+may be confused by a datasheet talking about a pin being possible to set
+into "GPIO mode". It appears that what hardware engineers mean with
+"GPIO mode" is not necessarily the use case that is implied in the kernel
+interface <linux/gpio.h>: a pin that you grab from kernel code and then
+either listen for input or drive high/low to assert/deassert some
+external line.
Rather hardware engineers think that "GPIO mode" means that you can
software-control a few electrical properties of the pin that you would
not be able to control if the pin was in some other mode, such as muxed in
for a device.
+The GPIO portions of a pin and its relation to a certain pin controller
+configuration and muxing logic can be constructed in several ways. Here
+are two examples:
+
+(A)
+ pin config
+ logic regs
+ | +- SPI
+ Physical pins --- pad --- pinmux -+- I2C
+ | +- mmc
+ | +- GPIO
+ pin
+ multiplex
+ logic regs
+
+Here some electrical properties of the pin can be configured no matter
+whether the pin is used for GPIO or not. If you multiplex a GPIO onto a
+pin, you can also drive it high/low from "GPIO" registers.
+Alternatively, the pin can be controlled by a certain peripheral, while
+still applying desired pin config properties. GPIO functionality is thus
+orthogonal to any other device using the pin.
+
+In this arrangement the registers for the GPIO portions of the pin controller,
+or the registers for the GPIO hardware module are likely to reside in a
+separate memory range only intended for GPIO driving, and the register
+range dealing with pin config and pin multiplexing get placed into a
+different memory range and a separate section of the data sheet.
+
+(B)
+
+ pin config
+ logic regs
+ | +- SPI
+ Physical pins --- pad --- pinmux -+- I2C
+ | | +- mmc
+ | |
+ GPIO pin
+ multiplex
+ logic regs
+
+In this arrangement, the GPIO functionality can always be enabled, such that
+e.g. a GPIO input can be used to "spy" on the SPI/I2C/MMC signal while it is
+pulsed out. It is likely possible to disrupt the traffic on the pin by doing
+wrong things on the GPIO block, as it is never really disconnected. It is
+possible that the GPIO, pin config and pin multiplex registers are placed into
+the same memory range and the same section of the data sheet, although that
+need not be the case.
+
+From a kernel point of view, however, these are different aspects of the
+hardware and shall be put into different subsystems:
+
+- Registers (or fields within registers) that control electrical
+ properties of the pin such as biasing and drive strength should be
+ exposed through the pinctrl subsystem, as "pin configuration" settings.
+
+- Registers (or fields within registers) that control muxing of signals
+ from various other HW blocks (e.g. I2C, MMC, or GPIO) onto pins should
+ be exposed through the pinctrl subssytem, as mux functions.
+
+- Registers (or fields within registers) that control GPIO functionality
+ such as setting a GPIO's output value, reading a GPIO's input value, or
+ setting GPIO pin direction should be exposed through the GPIO subsystem,
+ and if they also support interrupt capabilities, through the irqchip
+ abstraction.
+
+Depending on the exact HW register design, some functions exposed by the
+GPIO subsystem may call into the pinctrl subsystem in order to
+co-ordinate register settings across HW modules. In particular, this may
+be needed for HW with separate GPIO and pin controller HW modules, where
+e.g. GPIO direction is determined by a register in the pin controller HW
+module rather than the GPIO HW module.
+
+Electrical properties of the pin such as biasing and drive strength
+may be placed at some pin-specific register in all cases or as part
+of the GPIO register in case (B) especially. This doesn't mean that such
+properties necessarily pertain to what the Linux kernel calls "GPIO".
+
Example: a pin is usually muxed in to be used as a UART TX line. But during
system sleep, we need to put this pin into "GPIO mode" and ground it.
OpenPOWER on IntegriCloud