Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
  trivial: chack -> check typo fix in main Makefile
  trivial: Add a space (and a comma) to a printk in 8250 driver
  trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
  trivial: Fix misspelling of "firmware" in powerpc Makefile
  trivial: Fix misspelling of "firmware" in usb.c
  trivial: Fix misspelling of "firmware" in qla1280.c
  trivial: Fix misspelling of "firmware" in a100u2w.c
  trivial: Fix misspelling of "firmware" in megaraid.c
  trivial: Fix misspelling of "firmware" in ql4_mbx.c
  trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
  trivial: Fix misspelling of "firmware" in ipw2100.c
  trivial: Fix misspelling of "firmware" in atmel.c
  trivial: Fix misspelled firmware in Kconfig
  trivial: fix an -> a typos in documentation and comments
  trivial: fix then -> than typos in comments and documentation
  trivial: update Jesper Juhl CREDITS entry with new email
  trivial: fix singal -> signal typo
  trivial: Fix incorrect use of "loose" in event.c
  trivial: printk: fix indentation of new_text_line declaration
  trivial: rtc-stk17ta8: fix sparse warning
  ...

1 files changed, 3 insertions, 3 deletions

diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet
index aef5a9b..4d184f2 100644
--- a/Documentation/hwmon/abituguru-datasheet
+++ b/Documentation/hwmon/abituguru-datasheet
@@ -74,7 +74,7 @@ a sensor.
 Notice that some banks have both a read and a write address this is how the
 uGuru determines if a read from or a write to the bank is taking place, thus
 when reading you should always use the read address and when writing the
-write address. The write address is always one (1) more then the read address.
+write address. The write address is always one (1) more than the read address.
 
 
 uGuru ready
@@ -224,7 +224,7 @@ Bit 3: Beep if alarm							(RW)
 Bit 4: 1 if alarm cause measured temp is over the warning threshold	(R)
 Bit 5: 1 if alarm cause measured volt is over the max threshold		(R)
 Bit 6: 1 if alarm cause measured volt is under the min threshold	(R)
-Bit 7: Volt sensor: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Volt sensor: Shutdown if alarm persist for more than 4 seconds	(RW)
        Temp sensor: Shutdown if temp is over the shutdown threshold	(RW)
 
 *  This bit is only honored/used by the uGuru if a temp sensor is connected
@@ -293,7 +293,7 @@ Byte 0:
 Alarm behaviour for the selected sensor. A 1 enables the described behaviour.
 Bit 0: Give an alarm if measured rpm is under the min threshold	(RW)
 Bit 3: Beep if alarm						(RW)
-Bit 7: Shutdown if alarm persist for more then 4 seconds	(RW)
+Bit 7: Shutdown if alarm persist for more than 4 seconds	(RW)
 
 Byte 1:
 min threshold (scale as bank 0x26)