Merge commit 'v2.6.29' into x86/setup-lzma

4 files changed, 223 insertions, 13 deletions

diff --git a/Documentation/hwmon/adt7475 b/Documentation/hwmon/adt7475
new file mode 100644
index 0000000..a2b1abe
--- /dev/null
+++ b/Documentation/hwmon/adt7475
@@ -0,0 +1,87 @@
+This describes the interface for the ADT7475 driver:
+
+(there are 4 fans, numbered fan1 to fan4):
+
+fanX_input		Read the current speed of the fan (in RPMs)
+fanX_min		Read/write the minimum speed of the fan.  Dropping
+			below this sets an alarm.
+
+(there are three PWMs, numbered pwm1 to pwm3):
+
+pwmX			Read/write the current duty cycle of the PWM.  Writes
+			only have effect when auto mode is turned off (see
+			below).  Range is 0 - 255.
+
+pwmX_enable		Fan speed control method:
+
+			0 - No control (fan at full speed)
+			1 - Manual fan speed control (using pwm[1-*])
+			2 - Automatic fan speed control
+
+pwmX_auto_channels_temp	Select which channels affect this PWM
+
+			1 - TEMP1 controls PWM
+			2 - TEMP2 controls PWM
+			4 - TEMP3 controls PWM
+			6 - TEMP2 and TEMP3 control PWM
+			7 - All three inputs control PWM
+
+pwmX_freq		Read/write the PWM frequency in Hz. The number
+			should be one of the following:
+
+			11 Hz
+			14 Hz
+			22 Hz
+			29 Hz
+			35 Hz
+			44 Hz
+			58 Hz
+			88 Hz
+
+pwmX_auto_point1_pwm	Read/write the minimum PWM duty cycle in automatic mode
+
+pwmX_auto_point2_pwm	Read/write the maximum PWM duty cycle in automatic mode
+
+(there are three temperature settings numbered temp1 to temp3):
+
+tempX_input		Read the current temperature.  The value is in milli
+			degrees of Celsius.
+
+tempX_max		Read/write the upper temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_min		Read/write the lower temperature limit - exceeding this
+			will cause an alarm.
+
+tempX_offset		Read/write the temperature adjustment offset
+
+tempX_crit		Read/write the THERM limit for remote1.
+
+tempX_crit_hyst		Set the temperature value below crit where the
+			fans will stay on - this helps drive the temperature
+			low enough so it doesn't stay near the edge and
+			cause THERM to keep tripping.
+
+tempX_auto_point1_temp	Read/write the minimum temperature where the fans will
+			turn on in automatic mode.
+
+tempX_auto_point2_temp	Read/write the maximum temperature over which the fans
+			will run in automatic mode.  tempX_auto_point1_temp
+			and tempX_auto_point2_temp together define the
+			range of automatic control.
+
+tempX_alarm		Read a 1 if the max/min alarm is set
+tempX_fault		Read a 1 if either temp1 or temp3 diode has a fault
+
+(There are two voltage settings, in1 and in2):
+
+inX_input		Read the current voltage on VCC.  Value is in
+			millivolts.
+
+inX_min			read/write the minimum voltage limit.
+			Dropping below this causes an alarm.
+
+inX_max			read/write the maximum voltage limit.
+			Exceeding this causes an alarm.
+
+inX_alarm		Read a 1 if the max/min alarm is set.
diff --git a/Documentation/hwmon/hpfall.c b/Documentation/hwmon/hpfall.c
new file mode 100644
index 0000000..bbea1cc
--- /dev/null
+++ b/Documentation/hwmon/hpfall.c
@@ -0,0 +1,101 @@
+/* Disk protection for HP machines.
+ *
+ * Copyright 2008 Eric Piel
+ * Copyright 2009 Pavel Machek <pavel@suse.cz>
+ *
+ * GPLv2.
+ */
+
+#include <stdio.h>
+#include <stdlib.h>
+#include <unistd.h>
+#include <fcntl.h>
+#include <sys/stat.h>
+#include <sys/types.h>
+#include <string.h>
+#include <stdint.h>
+#include <errno.h>
+#include <signal.h>
+
+void write_int(char *path, int i)
+{
+	char buf[1024];
+	int fd = open(path, O_RDWR);
+	if (fd < 0) {
+		perror("open");
+		exit(1);
+	}
+	sprintf(buf, "%d", i);
+	if (write(fd, buf, strlen(buf)) != strlen(buf)) {
+		perror("write");
+		exit(1);
+	}
+	close(fd);
+}
+
+void set_led(int on)
+{
+	write_int("/sys/class/leds/hp::hddprotect/brightness", on);
+}
+
+void protect(int seconds)
+{
+	write_int("/sys/block/sda/device/unload_heads", seconds*1000);
+}
+
+int on_ac(void)
+{
+//	/sys/class/power_supply/AC0/online
+}
+
+int lid_open(void)
+{
+//	/proc/acpi/button/lid/LID/state
+}
+
+void ignore_me(void)
+{
+	protect(0);
+	set_led(0);
+
+}
+
+int main(int argc, char* argv[])
+{
+       int fd, ret;
+
+       fd = open("/dev/freefall", O_RDONLY);
+       if (fd < 0) {
+               perror("open");
+               return EXIT_FAILURE;
+       }
+
+	signal(SIGALRM, ignore_me);
+
+       for (;;) {
+	       unsigned char count;
+
+               ret = read(fd, &count, sizeof(count));
+	       alarm(0);
+	       if ((ret == -1) && (errno == EINTR)) {
+		       /* Alarm expired, time to unpark the heads */
+		       continue;
+	       }
+
+               if (ret != sizeof(count)) {
+                       perror("read");
+                       break;
+               }
+
+	       protect(21);
+	       set_led(1);
+	       if (1 || on_ac() || lid_open()) {
+		       alarm(2);
+	       } else {
+		       alarm(20);
+	       }
+       }
+
+       close(fd);
+       return EXIT_SUCCESS;
+}
diff --git a/Documentation/hwmon/lis3lv02d b/Documentation/hwmon/lis3lv02d
index 65dfb0c..287f8c9 100644
--- a/Documentation/hwmon/lis3lv02d
+++ b/Documentation/hwmon/lis3lv02d
@@ -13,23 +13,34 @@ Author:
 Description
 -----------
 
-This driver provides support for the accelerometer found in various HP laptops
-sporting the feature officially called "HP Mobile Data Protection System 3D" or
-"HP 3D DriveGuard". It detect automatically laptops with this sensor. Known models
-(for now the HP 2133, nc6420, nc2510, nc8510, nc84x0, nw9440 and nx9420) will
-have their axis automatically oriented on standard way (eg: you can directly
-play neverball).  The accelerometer data is readable via
+This driver provides support for the accelerometer found in various HP
+laptops sporting the feature officially called "HP Mobile Data
+Protection System 3D" or "HP 3D DriveGuard". It detect automatically
+laptops with this sensor. Known models (for now the HP 2133, nc6420,
+nc2510, nc8510, nc84x0, nw9440 and nx9420) will have their axis
+automatically oriented on standard way (eg: you can directly play
+neverball).  The accelerometer data is readable via
 /sys/devices/platform/lis3lv02d.
 
 Sysfs attributes under /sys/devices/platform/lis3lv02d/:
 position - 3D position that the accelerometer reports. Format: "(x,y,z)"
-calibrate - read: values (x, y, z) that are used as the base for input class device operation.
-            write: forces the base to be recalibrated with the current position.
+calibrate - read: values (x, y, z) that are used as the base for input
+		  class device operation.
+            write: forces the base to be recalibrated with the current
+		  position.
 rate - reports the sampling rate of the accelerometer device in HZ
 
 This driver also provides an absolute input class device, allowing
 the laptop to act as a pinball machine-esque joystick.
 
+Another feature of the driver is misc device called "freefall" that
+acts similar to /dev/rtc and reacts on free-fall interrupts received
+from the device. It supports blocking operations, poll/select and
+fasync operation modes. You must read 1 bytes from the device.  The
+result is number of free-fall interrupts since the last successful
+read (or 255 if number of interrupts would not fit).
+
+
 Axes orientation
 ----------------
 
@@ -39,11 +50,12 @@ the accelerometer are converted into a "standard" organisation of the axes
  * When the laptop is horizontal the position reported is about 0 for X and Y
 and a positive value for Z
  * If the left side is elevated, X increases (becomes positive)
- * If the front side (where the touchpad is) is elevated, Y decreases (becomes negative)
+ * If the front side (where the touchpad is) is elevated, Y decreases
+	(becomes negative)
  * If the laptop is put upside-down, Z becomes negative
 
-If your laptop model is not recognized (cf "dmesg"), you can send an email to the
-authors to add it to the database.  When reporting a new laptop, please include
-the output of "dmidecode" plus the value of /sys/devices/platform/lis3lv02d/position
-in these four cases.
+If your laptop model is not recognized (cf "dmesg"), you can send an
+email to the authors to add it to the database.  When reporting a new
+laptop, please include the output of "dmidecode" plus the value of
+/sys/devices/platform/lis3lv02d/position in these four cases.
 
diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90
index 0e84117..93d8e3d 100644
--- a/Documentation/hwmon/lm90
+++ b/Documentation/hwmon/lm90
@@ -42,6 +42,11 @@ Supported chips:
     Addresses scanned: I2C 0x4e
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3497
+  * Maxim MAX6648
+    Prefix: 'max6646'
+    Addresses scanned: I2C 0x4c
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3500
   * Maxim MAX6649
     Prefix: 'max6646'
     Addresses scanned: I2C 0x4c
@@ -74,6 +79,11 @@ Supported chips:
                            0x4c, 0x4d and 0x4e
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3370
+  * Maxim MAX6692
+    Prefix: 'max6646'
+    Addresses scanned: I2C 0x4c
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3500
 
 
 Author: Jean Delvare <khali@linux-fr.org>