summaryrefslogtreecommitdiffstats
path: root/Documentation/gpio.txt
diff options
context:
space:
mode:
authorDavid Brownell <david-b@pacbell.net>2007-02-16 01:27:14 -0800
committerLinus Torvalds <torvalds@woody.linux-foundation.org>2007-02-16 08:13:55 -0800
commitf5de611148c8370cbe50796ca5567ca624b99686 (patch)
treeb3dd73c3ad0414bbc83bca31f800a7af1b79dc3a /Documentation/gpio.txt
parent7de970e11fb832a56c897276967fb0e49f59b313 (diff)
downloadop-kernel-dev-f5de611148c8370cbe50796ca5567ca624b99686.zip
op-kernel-dev-f5de611148c8370cbe50796ca5567ca624b99686.tar.gz
[PATCH] GPIO core documentation
Small updates to the GPIO documentation, addressing feedback and fixing a few spelling errors. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Diffstat (limited to 'Documentation/gpio.txt')
-rw-r--r--Documentation/gpio.txt17
1 files changed, 10 insertions, 7 deletions
diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt
index 09dd510..576ce46 100644
--- a/Documentation/gpio.txt
+++ b/Documentation/gpio.txt
@@ -78,7 +78,8 @@ Identifying GPIOs
-----------------
GPIOs are identified by unsigned integers in the range 0..MAX_INT. That
reserves "negative" numbers for other purposes like marking signals as
-"not available on this board", or indicating faults.
+"not available on this board", or indicating faults. Code that doesn't
+touch the underlying hardware treats these integers as opaque cookies.
Platforms define how they use those integers, and usually #define symbols
for the GPIO lines so that board-specific setup code directly corresponds
@@ -139,10 +140,10 @@ issues including wire-OR and output latencies.
The get/set calls have no error returns because "invalid GPIO" should have
been reported earlier in gpio_set_direction(). However, note that not all
platforms can read the value of output pins; those that can't should always
-return zero. Also, these calls will be ignored for GPIOs that can't safely
-be accessed wihtout sleeping (see below).
+return zero. Also, using these calls for GPIOs that can't safely be accessed
+without sleeping (see below) is an error.
-Platform-specific implementations are encouraged to optimise the two
+Platform-specific implementations are encouraged to optimize the two
calls to access the GPIO value in cases where the GPIO number (and for
output, value) are constant. It's normal for them to need only a couple
of instructions in such cases (reading or writing a hardware register),
@@ -239,7 +240,8 @@ options are part of the IRQ interface, e.g. IRQF_TRIGGER_FALLING, as are
system wakeup capabilities.
Non-error values returned from irq_to_gpio() would most commonly be used
-with gpio_get_value().
+with gpio_get_value(), for example to initialize or update driver state
+when the IRQ is edge-triggered.
@@ -260,9 +262,10 @@ pullups (or pulldowns) so that the on-chip ones should not be used.
There are other system-specific mechanisms that are not specified here,
like the aforementioned options for input de-glitching and wire-OR output.
Hardware may support reading or writing GPIOs in gangs, but that's usually
-configuration dependednt: for GPIOs sharing the same bank. (GPIOs are
+configuration dependent: for GPIOs sharing the same bank. (GPIOs are
commonly grouped in banks of 16 or 32, with a given SOC having several such
-banks.) Code relying on such mechanisms will necessarily be nonportable.
+banks.) Some systems can trigger IRQs from output GPIOs. Code relying on
+such mechanisms will necessarily be nonportable.
Dynamic definition of GPIOs is not currently supported; for example, as
a side effect of configuring an add-on board with some GPIO expanders.
OpenPOWER on IntegriCloud