Merge branch 'next/dt' of git://git.linaro.org/people/arnd/arm-soc

* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
  ARM: gic: use module.h instead of export.h
  ARM: gic: fix irq_alloc_descs handling for sparse irq
  ARM: gic: add OF based initialization
  ARM: gic: add irq_domain support
  irq: support domains with non-zero hwirq base
  of/irq: introduce of_irq_init
  ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
  ARM: at91: dt: at91sam9g45 family and board device tree files
  arm/mx5: add device tree support for imx51 babbage
  arm/mx5: add device tree support for imx53 boards
  ARM: msm: Add devicetree support for msm8660-surf
  msm_serial: Add devicetree support
  msm_serial: Use relative resources for iomem

Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}

3 files changed, 101 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
new file mode 100644
index 0000000..e2401cd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -0,0 +1,19 @@
+i.MX51 Babbage Board
+Required root node properties:
+    - compatible = "fsl,imx51-babbage", "fsl,imx51";
+
+i.MX53 Automotive Reference Design Board
+Required root node properties:
+    - compatible = "fsl,imx53-ard", "fsl,imx53";
+
+i.MX53 Evaluation Kit
+Required root node properties:
+    - compatible = "fsl,imx53-evk", "fsl,imx53";
+
+i.MX53 Quick Start Board
+Required root node properties:
+    - compatible = "fsl,imx53-qsb", "fsl,imx53";
+
+i.MX53 Smart Mobile Reference Design Board
+Required root node properties:
+    - compatible = "fsl,imx53-smd", "fsl,imx53";
diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt
new file mode 100644
index 0000000..52916b4
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/gic.txt
@@ -0,0 +1,55 @@
+* ARM Generic Interrupt Controller
+
+ARM SMP cores are often associated with a GIC, providing per processor
+interrupts (PPI), shared processor interrupts (SPI) and software
+generated interrupts (SGI).
+
+Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
+Secondary GICs are cascaded into the upward interrupt controller and do not
+have PPIs or SGIs.
+
+Main node required properties:
+
+- compatible : should be one of:
+	"arm,cortex-a9-gic"
+	"arm,arm11mp-gic"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source.  The type shall be a <u32> and the value shall be 3.
+
+  The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
+  interrupts.
+
+  The 2nd cell contains the interrupt number for the interrupt type.
+  SPI interrupts are in the range [0-987].  PPI interrupts are in the
+  range [0-15].
+
+  The 3rd cell is the flags, encoded as follows:
+	bits[3:0] trigger type and level flags.
+		1 = low-to-high edge triggered
+		2 = high-to-low edge triggered
+		4 = active high level-sensitive
+		8 = active low level-sensitive
+	bits[15:8] PPI interrupt cpu mask.  Each bit corresponds to each of
+	the 8 possible cpus attached to the GIC.  A bit set to '1' indicated
+	the interrupt is wired to that CPU.  Only valid for PPI interrupts.
+
+- reg : Specifies base physical address(s) and size of the GIC registers. The
+  first region is the GIC distributor register base and size. The 2nd region is
+  the GIC cpu interface register base and size.
+
+Optional
+- interrupts	: Interrupt source of the parent interrupt controller. Only
+  present on secondary GICs.
+
+Example:
+
+	intc: interrupt-controller@fff11000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		interrupt-controller;
+		reg = <0xfff11000 0x1000>,
+		      <0xfff10100 0x100>;
+	};
+
diff --git a/Documentation/devicetree/bindings/tty/serial/msm_serial.txt b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt
new file mode 100644
index 0000000..aef383e
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/msm_serial.txt
@@ -0,0 +1,27 @@
+* Qualcomm MSM UART
+
+Required properties:
+- compatible :
+	- "qcom,msm-uart", and one of "qcom,msm-hsuart" or
+	  "qcom,msm-lsuart".
+- reg : offset and length of the register set for the device
+	for the hsuart operating in compatible mode, there should be a
+	second pair describing the gsbi registers.
+- interrupts : should contain the uart interrupt.
+
+There are two different UART blocks used in MSM devices,
+"qcom,msm-hsuart" and "qcom,msm-lsuart".  The msm-serial driver is
+able to handle both of these, and matches against the "qcom,msm-uart"
+as the compatibility.
+
+The registers for the "qcom,msm-hsuart" device need to specify both
+register blocks, even for the common driver.
+
+Example:
+
+	uart@19c400000 {
+		compatible = "qcom,msm-hsuart", "qcom,msm-uart";
+		reg = <0x19c40000 0x1000>,
+		      <0x19c00000 0x1000>;
+		interrupts = <195>;
+	};