Merge tag 'usb-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v3.12 merge window

All patches here have been pending on linux-usb
and sitting in linux-next for a while now.

The biggest things in this tag are:

DWC3 learned proper usage of threaded IRQ
handlers and now we spend very little time
in hardirq context.

MUSB now has proper support for BeagleBone and
Beaglebone Black.

Tegra's USB support also got quite a bit of love
and is learning to use PHY layer and generic DT
attributes.

Other than that, the usual pack of cleanups and
non-critical fixes follow.

Signed-of-by: Felipe Balbi <balbi@ti.com>

Conflicts:
	drivers/usb/gadget/udc-core.c
	drivers/usb/host/ehci-tegra.c
	drivers/usb/musb/omap2430.c
	drivers/usb/musb/tusb6010.c

4 files changed, 82 insertions, 7 deletions

diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
index 7a95c65..e807635 100644
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/dwc3.txt
@@ -3,10 +3,12 @@ synopsys DWC3 CORE
 DWC3- USB3 CONTROLLER
 
 Required properties:
- - compatible: must be "synopsys,dwc3"
+ - compatible: must be "snps,dwc3"
  - reg : Address and length of the register set for the device
  - interrupts: Interrupts used by the dwc3 controller.
- - usb-phy : array of phandle for the PHY device
+ - usb-phy : array of phandle for the PHY device.  The first element
+   in the array is expected to be a handle to the USB2/HS PHY and
+   the second element is expected to be a handle to the USB3/SS PHY
 
 Optional properties:
  - tx-fifo-resize: determines if the FIFO *has* to be reallocated.
@@ -14,7 +16,7 @@ Optional properties:
 This is usually a subnode to DWC3 glue to which it is connected.
 
 dwc3@4a030000 {
-	compatible = "synopsys,dwc3";
+	compatible = "snps,dwc3";
 	reg = <0x4a030000 0xcfff>;
 	interrupts = <0 92 4>
 	usb-phy = <&usb2_phy>, <&usb3,phy>;
diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt
new file mode 100644
index 0000000..477d5bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/generic.txt
@@ -0,0 +1,24 @@
+Generic USB Properties
+
+Optional properties:
+ - maximum-speed: tells USB controllers we want to work up to a certain
+			speed. Valid arguments are "super-speed", "high-speed",
+			"full-speed" and "low-speed". In case this isn't passed
+			via DT, USB controllers should default to their maximum
+			HW capability.
+ - dr_mode: tells Dual-Role USB controllers that we want to work on a
+			particular mode. Valid arguments are "host",
+			"peripheral" and "otg". In case this attribute isn't
+			passed via DT, USB DRD controllers should default to
+			OTG.
+
+This is an attribute to a USB controller such as:
+
+dwc3@4a030000 {
+	compatible = "synopsys,dwc3";
+	reg = <0x4a030000 0xcfff>;
+	interrupts = <0 92 4>
+	usb-phy = <&usb2_phy>, <&usb3,phy>;
+	maximum-speed = "super-speed";
+	dr_mode = "otg";
+};
diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
index c4c9e9e..ba797d3 100644
--- a/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-usb-phy.txt
@@ -3,7 +3,7 @@ Tegra SOC USB PHY
 The device node for Tegra SOC USB PHY:
 
 Required properties :
- - compatible : Should be "nvidia,tegra20-usb-phy".
+ - compatible : Should be "nvidia,tegra<chip>-usb-phy".
  - reg : Defines the following set of registers, in the order listed:
    - The PHY's own register set.
      Always present.
@@ -24,17 +24,26 @@ Required properties :
 Required properties for phy_type == ulpi:
   - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
 
-Required PHY timing params for utmi phy:
+Required PHY timing params for utmi phy, for all chips:
   - nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
     start of sync launches RxActive
   - nvidia,elastic-limit : Variable FIFO Depth of elastic input store
   - nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
     before declare IDLE.
   - nvidia,term-range-adj : Range adjusment on terminations
-  - nvidia,xcvr-setup : HS driver output control
+  - Either one of the following for HS driver output control:
+    - nvidia,xcvr-setup : integer, uses the provided value.
+    - nvidia,xcvr-setup-use-fuses : boolean, indicates that the value is read
+      from the on-chip fuses
+    If both are provided, nvidia,xcvr-setup-use-fuses takes precedence.
   - nvidia,xcvr-lsfslew : LS falling slew rate control.
   - nvidia,xcvr-lsrslew :  LS rising slew rate control.
 
+Required PHY timing params for utmi phy, only on Tegra30 and above:
+  - nvidia,xcvr-hsslew : HS slew rate control.
+  - nvidia,hssquelch-level : HS squelch detector level.
+  - nvidia,hsdiscon-level : HS disconnect detector level.
+
 Optional properties:
   - nvidia,has-legacy-mode : boolean indicates whether this controller can
     operate in legacy mode (as APX 2500 / 2600). In legacy mode some
@@ -48,5 +57,5 @@ Optional properties:
       peripheral means it is device controller
       otg means it can operate as either ("on the go")
 
-Required properties for dr_mode == otg:
+VBUS control (required for dr_mode == otg, optional for dr_mode == host):
   - vbus-supply: regulator for VBUS
diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt
new file mode 100644
index 0000000..b83d428
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt
@@ -0,0 +1,40 @@
+Samsung High Speed USB OTG controller
+-----------------------------
+
+The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards.
+It gives functionality of OTG-compliant USB 2.0 host and device with
+support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps)
+operation.
+
+Currently only device mode is supported.
+
+Binding details
+-----
+
+Required properties:
+- compatible: "samsung,s3c6400-hsotg" should be used for all currently
+    supported SoC,
+- interrupt-parent: phandle for the interrupt controller to which the
+    interrupt signal of the HSOTG block is routed,
+- interrupts: specifier of interrupt signal of interrupt controller,
+    according to bindings of interrupt controller,
+- clocks: contains an array of clock specifiers:
+    - first entry: OTG clock
+- clock-names: contains array of clock names:
+    - first entry: must be "otg"
+- vusb_d-supply: phandle to voltage regulator of digital section,
+- vusb_a-supply: phandle to voltage regulator of analog section.
+
+Example
+-----
+
+	hsotg@12480000 {
+		compatible = "samsung,s3c6400-hsotg";
+		reg = <0x12480000 0x20000>;
+		interrupts = <0 71 0>;
+		clocks = <&clock 305>;
+		clock-names = "otg";
+		vusb_d-supply = <&vusb_reg>;
+		vusb_a-supply = <&vusbdac_reg>;
+	};
+