summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree
diff options
context:
space:
mode:
authorKevin Hilman <khilman@linaro.org>2015-06-24 21:32:15 -0700
committerKevin Hilman <khilman@linaro.org>2015-06-24 21:32:15 -0700
commit39e79b873e1bafc5637a1a704495b01edbe469b1 (patch)
treeadc6a52bbb4d15eca8cdff567d3a44db6ce24c0c /Documentation/devicetree
parent03fa626774a30145bdb97ce1bc909a0cfd419ce6 (diff)
parent58c179674329b4d03a9d22df55d95cb0a8da5d85 (diff)
downloadop-kernel-dev-39e79b873e1bafc5637a1a704495b01edbe469b1.zip
op-kernel-dev-39e79b873e1bafc5637a1a704495b01edbe469b1.tar.gz
Merge tag 'armsoc-dt' into test-merge
ARM: SoC: DT updates for v4.2 As usual, quite a few device-tree updates in ARM land. There was ome minor churn in DTs due to relicensing under a dual-license, and lots of little additions of new peripherals, features etc, but nothing really exciting to call to your attention. Some higlights, focsuing on support for new SoCs and boards: - AT91: new boards: Overkiz, Acme Systems' Arietta G25 - tegra: HDA support - bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS RT-AC87U - mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys boards, DLink DNS-327L - OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill SL50 - ARM: added support for Juno r1 board - sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33, Mele A1000G - imx: i.MX7D SoC support; new boards: Armadeus Systems APF6, Gateworks GW5510, and aristainetos2 boards - hisilicon: hi6220 SoC support; new boards: 96boards hikey Conflicts: None # gpg: Signature made Wed Jun 24 21:32:14 2015 PDT using RSA key ID D3FBC665 # gpg: Good signature from "Kevin Hilman <khilman@deeprootsystems.com>" # gpg: aka "Kevin Hilman <khilman@linaro.org>" # gpg: aka "Kevin Hilman <khilman@kernel.org>"
Diffstat (limited to 'Documentation/devicetree')
-rw-r--r--Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt12
-rw-r--r--Documentation/devicetree/bindings/arm/arm-boards66
-rw-r--r--Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt31
-rw-r--r--Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt76
-rw-r--r--Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt87
-rw-r--r--Documentation/devicetree/bindings/arm/marvell,berlin.txt100
-rw-r--r--Documentation/devicetree/bindings/arm/scu.txt25
-rw-r--r--Documentation/devicetree/bindings/arm/ux500/boards.txt83
-rw-r--r--Documentation/devicetree/bindings/clock/hi6220-clock.txt34
-rw-r--r--Documentation/devicetree/bindings/clock/imx7d-clock.txt13
-rw-r--r--Documentation/devicetree/bindings/clock/marvell,berlin.txt31
-rw-r--r--Documentation/devicetree/bindings/pci/xilinx-pcie.txt2
-rw-r--r--Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt43
-rw-r--r--Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt27
-rw-r--r--Documentation/devicetree/bindings/reset/berlin,reset.txt23
-rw-r--r--Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt19
-rw-r--r--Documentation/devicetree/bindings/rtc/s3c-rtc.txt3
-rw-r--r--Documentation/devicetree/bindings/spi/sh-msiof.txt2
-rw-r--r--Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt4
-rw-r--r--Documentation/devicetree/bindings/usb/atmel-usb.txt25
-rw-r--r--Documentation/devicetree/bindings/vendor-prefixes.txt8
21 files changed, 631 insertions, 83 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt
new file mode 100644
index 0000000..77ca635
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt
@@ -0,0 +1,12 @@
+Altera SOCFPGA SDRAM Controller
+
+Required properties:
+- compatible : Should contain "altr,sdr-ctl" and "syscon".
+ syscon is required by the Altera SOCFPGA SDRAM EDAC.
+- reg : Should contain 1 register range (address and length)
+
+Example:
+ sdr: sdr@ffc25000 {
+ compatible = "altr,sdr-ctl", "syscon";
+ reg = <0xffc25000 0x1000>;
+ };
diff --git a/Documentation/devicetree/bindings/arm/arm-boards b/Documentation/devicetree/bindings/arm/arm-boards
index b78564b2..1a70997 100644
--- a/Documentation/devicetree/bindings/arm/arm-boards
+++ b/Documentation/devicetree/bindings/arm/arm-boards
@@ -157,3 +157,69 @@ Example:
};
};
+
+ARM Versatile Express Boards
+-----------------------------
+For details on the device tree bindings for ARM Versatile Express boards
+please consult the vexpress.txt file in the same directory as this file.
+
+ARM Juno Boards
+----------------
+The Juno boards are targeting development for AArch64 systems. The first
+iteration, Juno r0, is a vehicle for evaluating big.LITTLE on AArch64,
+with the second iteration, Juno r1, mainly aimed at development of PCIe
+based systems. Juno r1 also has support for AXI masters placed on the TLX
+connectors to join the coherency domain.
+
+Juno boards are described in a similar way to ARM Versatile Express boards,
+with the motherboard part of the hardware being described in a separate file
+to highlight the fact that is part of the support infrastructure for the SoC.
+Juno device tree bindings also share the Versatile Express bindings as
+described under the RS1 memory mapping.
+
+Required properties (in root node):
+ compatible = "arm,juno"; /* For Juno r0 board */
+ compatible = "arm,juno-r1"; /* For Juno r1 board */
+
+Required nodes:
+The description for the board must include:
+ - a "psci" node describing the boot method used for the secondary CPUs.
+ A detailed description of the bindings used for "psci" nodes is present
+ in the psci.txt file.
+ - a "cpus" node describing the available cores and their associated
+ "enable-method"s. For more details see cpus.txt file.
+
+Example:
+
+/dts-v1/;
+/ {
+ model = "ARM Juno development board (r0)";
+ compatible = "arm,juno", "arm,vexpress";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ A57_0: cpu@0 {
+ compatible = "arm,cortex-a57","arm,armv8";
+ reg = <0x0 0x0>;
+ device_type = "cpu";
+ enable-method = "psci";
+ };
+
+ .....
+
+ A53_0: cpu@100 {
+ compatible = "arm,cortex-a53","arm,armv8";
+ reg = <0x0 0x100>;
+ device_type = "cpu";
+ enable-method = "psci";
+ };
+
+ .....
+ };
+
+};
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
index ac68348..c78576b 100644
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
@@ -1,8 +1,35 @@
Broadcom BCM2835 device tree bindings
-------------------------------------------
-Boards with the BCM2835 SoC shall have the following properties:
+Raspberry Pi Model A
+Required root node properties:
+compatible = "raspberrypi,model-a", "brcm,bcm2835";
-Required root node property:
+Raspberry Pi Model A+
+Required root node properties:
+compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
+Raspberry Pi Model B
+Required root node properties:
+compatible = "raspberrypi,model-b", "brcm,bcm2835";
+
+Raspberry Pi Model B (no P5)
+early model B with I2C0 rather than I2C1 routed to the expansion header
+Required root node properties:
+compatible = "raspberrypi,model-b-i2c0", "brcm,bcm2835";
+
+Raspberry Pi Model B rev2
+Required root node properties:
+compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
+
+Raspberry Pi Model B+
+Required root node properties:
+compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+
+Raspberry Pi Compute Module
+Required root node properties:
+compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+
+Generic BCM2835 board
+Required root node properties:
compatible = "brcm,bcm2835";
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt
index bd49987..b82b6a0 100644
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt
@@ -7,3 +7,79 @@ following properties:
Required root node property:
compatible: should be "brcm,bcm63138"
+
+An optional Boot lookup table Device Tree node is required for secondary CPU
+initialization as well as a 'resets' phandle to the correct PMB controller as
+defined in reset/brcm,bcm63138-pmb.txt for this secondary CPU, and an
+'enable-method' property.
+
+Required properties for the Boot lookup table node:
+- compatible: should be "brcm,bcm63138-bootlut"
+- reg: register base address and length for the Boot Lookup table
+
+Optional properties for the primary CPU node:
+- enable-method: should be "brcm,bcm63138"
+
+Optional properties for the secondary CPU node:
+- enable-method: should be "brcm,bcm63138"
+- resets: phandle to the relevant PMB controller, one integer indicating the internal
+ bus number, and a second integer indicating the address of the CPU in the PMB
+ internal bus number.
+
+Example:
+
+ cpus {
+ cpu@0 {
+ compatible = "arm,cotex-a9";
+ reg = <0>;
+ ...
+ enable-method = "brcm,bcm63138";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a9";
+ reg = <1>;
+ ...
+ enable-method = "brcm,bcm63138";
+ resets = <&pmb0 4 1>;
+ };
+ };
+
+ bootlut: bootlut@8000 {
+ compatible = "brcm,bcm63138-bootlut";
+ reg = <0x8000 0x50>;
+ };
+
+=======
+reboot
+------
+Two nodes are required for software reboot: a timer node and a syscon-reboot node.
+
+Timer node:
+
+- compatible: Must be "brcm,bcm6328-timer", "syscon"
+- reg: Register base address and length
+
+Syscon reboot node:
+
+See Documentation/devicetree/bindings/power/reset/syscon-reboot.txt for the
+detailed list of properties, the two values defined below are specific to the
+BCM6328-style timer:
+
+- offset: Should be 0x34 to denote the offset of the TIMER_WD_TIMER_RESET register
+ from the beginning of the TIMER block
+- mask: Should be 1 for the SoftRst bit.
+
+Example:
+
+ timer: timer@80 {
+ compatible = "brcm,bcm6328-timer", "syscon";
+ reg = <0x80 0x3c>;
+ };
+
+ reboot {
+ compatible = "syscon-reboot";
+ regmap = <&timer>;
+ offset = <0x34>;
+ mask = <0x1>;
+ };
diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
index 35b1bd4..c431c67 100644
--- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
@@ -1,5 +1,8 @@
Hisilicon Platforms Device Tree Bindings
----------------------------------------------------
+Hi6220 SoC
+Required root node properties:
+ - compatible = "hisilicon,hi6220";
Hi4511 Board
Required root node properties:
@@ -13,6 +16,9 @@ HiP01 ca9x2 Board
Required root node properties:
- compatible = "hisilicon,hip01-ca9x2";
+HiKey Board
+Required root node properties:
+ - compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220";
Hisilicon system controller
@@ -41,6 +47,87 @@ Example:
};
-----------------------------------------------------------------------
+Hisilicon Hi6220 system controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-sysctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+ under this controller and this property must be present.
+
+Hisilicon designs this controller as one of the system controllers,
+its main functions are the same as Hisilicon system controller, but
+the register offset of some core modules are different.
+
+Example:
+ /*for Hi6220*/
+ sys_ctrl: sys_ctrl@f7030000 {
+ compatible = "hisilicon,hi6220-sysctrl", "syscon";
+ reg = <0x0 0xf7030000 0x0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+
+Hisilicon Hi6220 Power Always ON domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-aoctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+ under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the power always
+on domain for mobile platform.
+
+Example:
+ /*for Hi6220*/
+ ao_ctrl: ao_ctrl@f7800000 {
+ compatible = "hisilicon,hi6220-aoctrl", "syscon";
+ reg = <0x0 0xf7800000 0x0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+
+Hisilicon Hi6220 Media domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-mediactrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+ under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the multimedia
+domain(e.g. codec, G3D ...) for mobile platform.
+
+Example:
+ /*for Hi6220*/
+ media_ctrl: media_ctrl@f4410000 {
+ compatible = "hisilicon,hi6220-mediactrl", "syscon";
+ reg = <0x0 0xf4410000 0x0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+
+Hisilicon Hi6220 Power Management domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-pmctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, some clock registers are define
+ under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the power management
+domain for mobile platform.
+
+Example:
+ /*for Hi6220*/
+ pm_ctrl: pm_ctrl@f7032000 {
+ compatible = "hisilicon,hi6220-pmctrl", "syscon";
+ reg = <0x0 0xf7032000 0x0 0x1000>;
+ #clock-cells = <1>;
+ };
+
+-----------------------------------------------------------------------
Hisilicon HiP01 system controller
Required properties:
diff --git a/Documentation/devicetree/bindings/arm/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/marvell,berlin.txt
index a99eb9e..3bab184 100644
--- a/Documentation/devicetree/bindings/arm/marvell,berlin.txt
+++ b/Documentation/devicetree/bindings/arm/marvell,berlin.txt
@@ -1,6 +1,18 @@
Marvell Berlin SoC Family Device Tree Bindings
---------------------------------------------------------------
+Work in progress statement:
+
+Device tree files and bindings applying to Marvell Berlin SoCs and boards are
+considered "unstable". Any Marvell Berlin device tree binding may change at any
+time. Be sure to use a device tree binary and a kernel image generated from the
+same source tree.
+
+Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a
+stable binding/ABI.
+
+---------------------------------------------------------------
+
Boards with a SoC of the Marvell Berlin family, e.g. Armada 1500
shall have the following properties:
@@ -49,10 +61,9 @@ chip control registers, so there should be a single DT node only providing the
different functions which are described below.
Required properties:
-- compatible: shall be one of
- "marvell,berlin2-chip-ctrl" for BG2
- "marvell,berlin2cd-chip-ctrl" for BG2CD
- "marvell,berlin2q-chip-ctrl" for BG2Q
+- compatible:
+ * the first and second values must be:
+ "simple-mfd", "syscon"
- reg: address and length of following register sets for
BG2/BG2CD: chip control register set
BG2Q: chip control register set and cpu pll registers
@@ -63,90 +74,23 @@ Marvell Berlin SoCs have a system control register set providing several
individual registers dealing with pinmux, padmux, and reset.
Required properties:
-- compatible: should be one of
- "marvell,berlin2-system-ctrl" for BG2
- "marvell,berlin2cd-system-ctrl" for BG2CD
- "marvell,berlin2q-system-ctrl" for BG2Q
+- compatible:
+ * the first and second values must be:
+ "simple-mfd", "syscon"
- reg: address and length of the system control register set
-* Clock provider binding
-
-As clock related registers are spread among the chip control registers, the
-chip control node also provides the clocks. Marvell Berlin2 (BG2, BG2CD, BG2Q)
-SoCs share the same IP for PLLs and clocks, with some minor differences in
-features and register layout.
-
-Required properties:
-- #clock-cells: shall be set to 1
-- clocks: clock specifiers referencing the core clock input clocks
-- clock-names: array of strings describing the input clock specifiers above.
- Allowed clock-names for the reference clocks are
- "refclk" for the SoCs osciallator input on all SoCs,
- and SoC-specific input clocks for
- BG2/BG2CD: "video_ext0" for the external video clock input
-
-Clocks provided by core clocks shall be referenced by a clock specifier
-indexing one of the provided clocks. Refer to dt-bindings/clock/berlin<soc>.h
-for the corresponding index mapping.
-
-* Pin controller binding
-
-Pin control registers are part of both register sets, chip control and system
-control. The pins controlled are organized in groups, so no actual pin
-information is needed.
-
-A pin-controller node should contain subnodes representing the pin group
-configurations, one per function. Each subnode has the group name and the muxing
-function used.
-
-Be aware the Marvell Berlin datasheets use the keyword 'mode' for what is called
-a 'function' in the pin-controller subsystem.
-
-Required subnode-properties:
-- groups: a list of strings describing the group names.
-- function: a string describing the function used to mux the groups.
-
-* Reset controller binding
-
-A reset controller is part of the chip control registers set. The chip control
-node also provides the reset. The register set is not at the same offset between
-Berlin SoCs.
-
-Required property:
-- #reset-cells: must be set to 2
-
Example:
chip: chip-control@ea0000 {
- compatible = "marvell,berlin2-chip-ctrl";
- #clock-cells = <1>;
- #reset-cells = <2>;
+ compatible = "simple-mfd", "syscon";
reg = <0xea0000 0x400>;
- clocks = <&refclk>, <&externaldev 0>;
- clock-names = "refclk", "video_ext0";
- spi1_pmux: spi1-pmux {
- groups = "G0";
- function = "spi1";
- };
+ /* sub-device nodes */
};
sysctrl: system-controller@d000 {
- compatible = "marvell,berlin2-system-ctrl";
+ compatible = "simple-mfd", "syscon";
reg = <0xd000 0x100>;
- uart0_pmux: uart0-pmux {
- groups = "GSM4";
- function = "uart0";
- };
-
- uart1_pmux: uart1-pmux {
- groups = "GSM5";
- function = "uart1";
- };
-
- uart2_pmux: uart2-pmux {
- groups = "GSM3";
- function = "uart2";
- };
+ /* sub-device nodes */
};
diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt
new file mode 100644
index 0000000..c447680
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/scu.txt
@@ -0,0 +1,25 @@
+* ARM Snoop Control Unit (SCU)
+
+As part of the MPCore complex, Cortex-A5 and Cortex-A9 are provided
+with a Snoop Control Unit. The register range is usually 256 (0x100)
+bytes.
+
+References:
+
+- Cortex-A9: see DDI0407E Cortex-A9 MPCore Technical Reference Manual
+ Revision r2p0
+- Cortex-A5: see DDI0434B Cortex-A5 MPCore Technical Reference Manual
+ Revision r0p1
+
+- compatible : Should be:
+ "arm,cortex-a9-scu"
+ "arm,cortex-a5-scu"
+
+- reg : Specify the base address and the size of the SCU register window.
+
+Example:
+
+scu@a04100000 {
+ compatible = "arm,cortex-a9-scu";
+ reg = <0xa0410000 0x100>;
+};
diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt
new file mode 100644
index 0000000..b8737a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt
@@ -0,0 +1,83 @@
+ST-Ericsson Ux500 boards
+------------------------
+
+Required properties (in root node) one of these:
+ compatible = "st-ericsson,mop500" (legacy)
+ compatible = "st-ericsson,u8500"
+
+Required node (under root node):
+
+soc: represents the system-on-chip and contains the chip
+peripherals
+
+Required property of soc node, one of these:
+ compatible = "stericsson,db8500"
+
+Required subnodes under soc node:
+
+backupram: (used for CPU spin tables and for storing data
+during retention, system won't boot without this):
+ compatible = "ste,dbx500-backupram"
+
+scu:
+ see binding for arm/scu.txt
+
+interrupt-controller:
+ see binding for arm/gic.txt
+
+timer:
+ see binding for arm/twd.txt
+
+clocks:
+ see binding for clocks/ux500.txt
+
+Example:
+
+/dts-v1/;
+
+/ {
+ model = "ST-Ericsson HREF (pre-v60) and ST UIB";
+ compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "stericsson,db8500";
+ interrupt-parent = <&intc>;
+ ranges;
+
+ backupram@80150000 {
+ compatible = "ste,dbx500-backupram";
+ reg = <0x80150000 0x2000>;
+ };
+
+ intc: interrupt-controller@a0411000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ interrupt-controller;
+ reg = <0xa0411000 0x1000>,
+ <0xa0410100 0x100>;
+ };
+
+ scu@a04100000 {
+ compatible = "arm,cortex-a9-scu";
+ reg = <0xa0410000 0x100>;
+ };
+
+ timer@a0410600 {
+ compatible = "arm,cortex-a9-twd-timer";
+ reg = <0xa0410600 0x20>;
+ interrupts = <1 13 0x304>; /* IRQ level high per-CPU */
+ clocks = <&smp_twd_clk>;
+ };
+
+ clocks {
+ compatible = "stericsson,u8500-clks";
+
+ smp_twd_clk: smp-twd-clock {
+ #clock-cells = <0>;
+ };
+ };
+ };
+};
diff --git a/Documentation/devicetree/bindings/clock/hi6220-clock.txt b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
new file mode 100644
index 0000000..259e30a
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/hi6220-clock.txt
@@ -0,0 +1,34 @@
+* Hisilicon Hi6220 Clock Controller
+
+Clock control registers reside in different Hi6220 system controllers,
+please refer the following document to know more about the binding rules
+for these system controllers:
+
+Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+
+Required Properties:
+
+- compatible: the compatible should be one of the following strings to
+ indicate the clock controller functionality.
+
+ - "hisilicon,hi6220-aoctrl"
+ - "hisilicon,hi6220-sysctrl"
+ - "hisilicon,hi6220-mediactrl"
+ - "hisilicon,hi6220-pmctrl"
+
+- reg: physical base address of the controller and length of memory mapped
+ region.
+
+- #clock-cells: should be 1.
+
+For example:
+ sys_ctrl: sys_ctrl@f7030000 {
+ compatible = "hisilicon,hi6220-sysctrl", "syscon";
+ reg = <0x0 0xf7030000 0x0 0x2000>;
+ #clock-cells = <1>;
+ };
+
+Each clock is assigned an identifier and client nodes use this identifier
+to specify the clock which they consume.
+
+All these identifier could be found in <dt-bindings/clock/hi6220-clock.h>.
diff --git a/Documentation/devicetree/bindings/clock/imx7d-clock.txt b/Documentation/devicetree/bindings/clock/imx7d-clock.txt
new file mode 100644
index 0000000..9d3026d
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/imx7d-clock.txt
@@ -0,0 +1,13 @@
+* Clock bindings for Freescale i.MX7 Dual
+
+Required properties:
+- compatible: Should be "fsl,imx7d-ccm"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+- clocks: list of clock specifiers, must contain an entry for each required
+ entry in clock-names
+- clock-names: should include entries "ckil", "osc"
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx7d-clock.h
+for the full list of i.MX7 Dual clock IDs.
diff --git a/Documentation/devicetree/bindings/clock/marvell,berlin.txt b/Documentation/devicetree/bindings/clock/marvell,berlin.txt
new file mode 100644
index 0000000..c611c49
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/marvell,berlin.txt
@@ -0,0 +1,31 @@
+Device Tree Clock bindings for Marvell Berlin
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Clock related registers are spread among the chip control registers. Berlin
+clock node should be a sub-node of the chip controller node. Marvell Berlin2
+(BG2, BG2CD, BG2Q) SoCs share the same IP for PLLs and clocks, with some
+minor differences in features and register layout.
+
+Required properties:
+- compatible: must be "marvell,berlin2-clk" or "marvell,berlin2q-clk"
+- #clock-cells: must be 1
+- clocks: must be the input parent clock phandle
+- clock-names: name of the input parent clock
+ Allowed clock-names for the reference clocks are
+ "refclk" for the SoCs oscillator input on all SoCs,
+ and SoC-specific input clocks for
+ BG2/BG2CD: "video_ext0" for the external video clock input
+
+
+Example:
+
+chip_clk: clock {
+ compatible = "marvell,berlin2q-clk";
+
+ #clock-cells = <1>;
+ clocks = <&refclk>;
+ clock-names = "refclk";
+};
diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
index 3e2c88d..02f979a 100644
--- a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt
@@ -58,5 +58,5 @@ Example:
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
- }
+ };
};
diff --git a/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt
new file mode 100644
index 0000000..a8bb5e2
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt
@@ -0,0 +1,43 @@
+* Pin-controller driver for the Marvell Berlin SoCs
+
+Pin control registers are part of both chip controller and system
+controller register sets. Pin controller nodes should be a sub-node of
+either the chip controller or system controller node. The pins
+controlled are organized in groups, so no actual pin information is
+needed.
+
+A pin-controller node should contain subnodes representing the pin group
+configurations, one per function. Each subnode has the group name and
+the muxing function used.
+
+Be aware the Marvell Berlin datasheets use the keyword 'mode' for what
+is called a 'function' in the pin-controller subsystem.
+
+Required properties:
+- compatible: should be one of:
+ "marvell,berlin2-soc-pinctrl",
+ "marvell,berlin2-system-pinctrl",
+ "marvell,berlin2cd-soc-pinctrl",
+ "marvell,berlin2cd-system-pinctrl",
+ "marvell,berlin2q-soc-pinctrl",
+ "marvell,berlin2q-system-pinctrl"
+
+Required subnode-properties:
+- groups: a list of strings describing the group names.
+- function: a string describing the function used to mux the groups.
+
+Example:
+
+sys_pinctrl: pin-controller {
+ compatible = "marvell,berlin2q-system-pinctrl";
+
+ uart0_pmux: uart0-pmux {
+ groups = "GSM12";
+ function = "uart0";
+ };
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pmux>;
+ pinctrl-names = "default";
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
new file mode 100644
index 0000000..8bbf25d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt
@@ -0,0 +1,27 @@
+* Freescale i.MX7 Dual IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx7d-iomuxc"
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+ setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val
+ input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+ imx7d-pinfunc.h under device tree source folder. The last integer CONFIG is
+ the pad setting value like pull-up on this pin. Please refer to i.MX7 Dual
+ Reference Manual for detailed CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_PUS_100K_DOWN (0 << 5)
+PAD_CTL_PUS_5K_UP (1 << 5)
+PAD_CTL_PUS_47K_UP (2 << 5)
+PAD_CTL_PUS_100K_UP (3 << 5)
+PAD_CTL_PUE (1 << 4)
+PAD_CTL_HYS (1 << 3)
+PAD_CTL_SRE_SLOW (1 << 2)
+PAD_CTL_SRE_FAST (0 << 2)
+PAD_CTL_DSE_X1 (0 << 0)
+PAD_CTL_DSE_X2 (1 << 0)
+PAD_CTL_DSE_X3 (2 << 0)
+PAD_CTL_DSE_X4 (3 << 0)
diff --git a/Documentation/devicetree/bindings/reset/berlin,reset.txt b/Documentation/devicetree/bindings/reset/berlin,reset.txt
new file mode 100644
index 0000000..514fee0
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/berlin,reset.txt
@@ -0,0 +1,23 @@
+Marvell Berlin reset controller
+===============================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+The reset controller node must be a sub-node of the chip controller
+node on Berlin SoCs.
+
+Required properties:
+- compatible: should be "marvell,berlin2-reset"
+- #reset-cells: must be set to 2
+
+Example:
+
+chip_rst: reset {
+ compatible = "marvell,berlin2-reset";
+ #reset-cells = <2>;
+};
+
+&usb_phy0 {
+ resets = <&chip_rst 0x104 12>;
+};
diff --git a/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt b/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt
new file mode 100644
index 0000000..a98872d
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt
@@ -0,0 +1,19 @@
+Broadcom BCM63138 Processor Monitor Bus binding
+===============================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Require properties:
+
+- compatible: must be "brcm,bcm63138-pmb"
+- reg: base register address and size for this bus controller
+- #reset-cells: must be 2 first cell is the address within the bus instance designated
+ by the phandle, and the second is the number of zones for this peripheral
+
+Example:
+ pmb0: reset-controller@4800c0 {
+ compatible = "brcm,bcm63138-pmb";
+ reg = <0x4800c0 0x10>;
+ #reset-cells = <2>;
+ };
diff --git a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
index ab757b84..ac2fcd6 100644
--- a/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/s3c-rtc.txt
@@ -6,7 +6,8 @@ Required properties:
* "samsung,s3c2416-rtc" - for controllers compatible with s3c2416 rtc.
* "samsung,s3c2443-rtc" - for controllers compatible with s3c2443 rtc.
* "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc.
- * "samsung,exynos3250-rtc" - for controllers compatible with exynos3250 rtc.
+ * "samsung,exynos3250-rtc" - (deprecated) for controllers compatible with
+ exynos3250 rtc (use "samsung,s3c6410-rtc").
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: Two interrupt numbers to the cpu should be specified. First
diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt
index 4c388bb..8f77144 100644
--- a/Documentation/devicetree/bindings/spi/sh-msiof.txt
+++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt
@@ -60,7 +60,7 @@ Example:
msiof0: spi@e6e20000 {
compatible = "renesas,msiof-r8a7791";
- reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>;
+ reg = <0 0xe6e20000 0 0x0064>;
interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
dmas = <&dmac0 0x51>, <&dmac0 0x52>;
diff --git a/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt b/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt
index 993695c..eeee6cd 100644
--- a/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt
+++ b/Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt
@@ -6,6 +6,9 @@ Required properties:
- interrupts : A list of 3 interrupts; one per timer channel.
- clocks: phandle to the source clock
+Optional properties:
+- timer-width: Bit width of the timer, necessary if not 16.
+
Example:
ttc0: ttc0@f8001000 {
@@ -14,4 +17,5 @@ ttc0: ttc0@f8001000 {
compatible = "cdns,ttc";
reg = <0xF8001000 0x1000>;
clocks = <&cpu_clk 3>;
+ timer-width = <32>;
};
diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt
index e180d56..1be8d7a 100644
--- a/Documentation/devicetree/bindings/usb/atmel-usb.txt
+++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt
@@ -5,6 +5,13 @@ OHCI
Required properties:
- compatible: Should be "atmel,at91rm9200-ohci" for USB controllers
used in host mode.
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain ehci interrupt
+ - clocks: Should reference the peripheral, host and system clocks
+ - clock-names: Should contains two strings
+ "ohci_clk" for the peripheral clock
+ "hclk" for the host clock
+ "uhpck" for the system clock
- num-ports: Number of ports.
- atmel,vbus-gpio: If present, specifies a gpio that needs to be
activated for the bus to be powered.
@@ -14,6 +21,8 @@ Required properties:
usb0: ohci@00500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x100000>;
+ clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+ clock-names = "ohci_clk", "hclk", "uhpck";
interrupts = <20 4>;
num-ports = <2>;
};
@@ -23,11 +32,19 @@ EHCI
Required properties:
- compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers
used in host mode.
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain ehci interrupt
+ - clocks: Should reference the peripheral and the UTMI clocks
+ - clock-names: Should contains two strings
+ "ehci_clk" for the peripheral clock
+ "usb_clk" for the UTMI clock
usb1: ehci@00800000 {
compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
reg = <0x00800000 0x100000>;
interrupts = <22 4>;
+ clocks = <&utmi>, <&uhphs_clk>;
+ clock-names = "usb_clk", "ehci_clk";
};
AT91 USB device controller
@@ -53,6 +70,8 @@ usb1: gadget@fffa4000 {
compatible = "atmel,at91rm9200-udc";
reg = <0xfffa4000 0x4000>;
interrupts = <10 4>;
+ clocks = <&udc_clk>, <&udpck>;
+ clock-names = "pclk", "hclk";
atmel,vbus-gpio = <&pioC 5 0>;
};
@@ -65,6 +84,10 @@ Required properties:
"sama5d3-udc"
- reg: Address and length of the register set for the device
- interrupts: Should contain usba interrupt
+ - clocks: Should reference the peripheral and host clocks
+ - clock-names: Should contains two strings
+ "pclk" for the peripheral clock
+ "hclk" for the host clock
- ep childnode: To specify the number of endpoints and their properties.
Optional properties:
@@ -86,6 +109,8 @@ usb2: gadget@fff78000 {
reg = <0x00600000 0x80000
0xfff78000 0x400>;
interrupts = <27 4 0>;
+ clocks = <&utmi>, <&udphs_clk>;
+ clock-names = "hclk", "pclk";
atmel,vbus-gpio = <&pioB 19 0>;
ep0 {
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 717ffd5..49cecc9 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -40,6 +40,7 @@ calxeda Calxeda
capella Capella Microsystems, Inc
cavium Cavium, Inc.
cdns Cadence Design Systems Inc.
+ceva Ceva, Inc.
chipidea Chipidea, Inc
chipone ChipOne
chipspark ChipSPARK
@@ -52,6 +53,7 @@ cnxt Conexant Systems, Inc.
cortina Cortina Systems, Inc.
cosmic Cosmic Circuits
crystalfontz Crystalfontz America, Inc.
+cubietech Cubietech, Ltd.
dallas Maxim Integrated Products (formerly Dallas Semiconductor)
davicom DAVICOM Semiconductor, Inc.
denx Denx Software Engineering
@@ -60,6 +62,7 @@ digilent Diglent, Inc.
dlg Dialog Semiconductor
dlink D-Link Corporation
dmo Data Modul AG
+ea Embedded Artists AB
ebv EBV Elektronik
edt Emerging Display Technologies
elan Elan Microelectronic Corp.
@@ -90,9 +93,11 @@ gumstix Gumstix, Inc.
gw Gateworks Corporation
hannstar HannStar Display Corporation
haoyu Haoyu Microelectronic Co. Ltd.
+hardkernel Hardkernel Co., Ltd
himax Himax Technologies, Inc.
hisilicon Hisilicon Limited.
hit Hitachi Ltd.
+hitex Hitex Development Tools
honeywell Honeywell
hp Hewlett Packard
i2se I2SE GmbH
@@ -159,6 +164,7 @@ radxa Radxa
raidsonic RaidSonic Technology GmbH
ralink Mediatek/Ralink Technology Corp.
ramtron Ramtron International
+raspberrypi Raspberry Pi Foundation
realtek Realtek Semiconductor Corp.
renesas Renesas Electronics Corporation
ricoh Ricoh Co. Ltd.
@@ -189,6 +195,7 @@ ste ST-Ericsson
stericsson ST-Ericsson
synology Synology, Inc.
tbs TBS Technologies
+tcl Toby Churchill Ltd.
thine THine Electronics, Inc.
ti Texas Instruments
tlm Trusted Logic Mobility
@@ -202,6 +209,7 @@ variscite Variscite Ltd.
via VIA Technologies, Inc.
virtio Virtual I/O Device Specification, developed by the OASIS consortium
voipac Voipac Technologies s.r.o.
+wexler Wexler
winbond Winbond Electronics corp.
wlf Wolfson Microelectronics
wm Wondermedia Technologies, Inc.
OpenPOWER on IntegriCloud