Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc driver specific updates from Olof Johansson:
 "These changes are specific to some driver that may be used by multiple
  boards or socs.  The most significant change in here is the move of
  the samsung iommu code from a platform specific in-kernel interface to
  the generic iommu subsystem."

Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
  mmc: dt: Consolidate DT bindings
  iommu/exynos: Add iommu driver for EXYNOS Platforms
  ARM: davinci: optimize the DMA ISR
  ARM: davinci: implement DEBUG_LL port choice
  ARM: tegra: Add SMMU enabler in AHB
  ARM: tegra: Add Tegra AHB driver
  Input: pxa27x_keypad add choice to set direct_key_mask
  Input: pxa27x_keypad direct key may be low active
  Input: pxa27x_keypad bug fix for direct_key_mask
  Input: pxa27x_keypad keep clock on as wakeup source
  ARM: dt: tegra: pinmux changes for USB ULPI
  ARM: tegra: add USB ULPI PHY reset GPIO to device tree
  ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
  ARM: tegra: change pll_p_out4's rate to 24MHz
  ARM: tegra: fix pclk rate
  ARM: tegra: reparent sclk to pll_c_out1
  ARM: tegra: Add pllc clock init table
  ARM: dt: tegra cardhu: basic audio support
  ARM: dt: tegra30.dtsi: Add audio-related nodes
  ARM: tegra: add AUXDATA required for audio
  ...

8 files changed, 52 insertions, 8 deletions

diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt
new file mode 100644
index 0000000..234406d
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-ahb.txt
@@ -0,0 +1,11 @@
+NVIDIA Tegra AHB
+
+Required properties:
+- compatible : "nvidia,tegra20-ahb" or "nvidia,tegra30-ahb"
+- reg : Should contain 1 register ranges(address and length)
+
+Example:
+	ahb: ahb@6000c004 {
+		compatible = "nvidia,tegra20-ahb";
+		reg = <0x6000c004 0x10c>; /* AHB Arbitration + Gizmo Controller */
+	};
diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
index 64bcb8b..0d93b4b 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
@@ -11,9 +11,11 @@ Required properties:
   - interrupt-parent : interrupt source phandle.
   - clock-frequency : specifies eSDHC base clock frequency.
   - sdhci,wp-inverted : (optional) specifies that eSDHC controller
-    reports inverted write-protect state;
+    reports inverted write-protect state; New devices should use
+    the generic "wp-inverted" property.
   - sdhci,1-bit-only : (optional) specifies that a controller can
-    only handle 1-bit data transfers.
+    only handle 1-bit data transfers. New devices should use the
+    generic "bus-width = <1>" property.
   - sdhci,auto-cmd12: (optional) specifies that a controller can
     only handle auto CMD12.
 
diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
index ab22fe6..c7e404b 100644
--- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt
@@ -9,7 +9,7 @@ Required properties:
 - interrupts : Should contain eSDHC interrupt
 
 Optional properties:
-- fsl,card-wired : Indicate the card is wired to host permanently
+- non-removable : Indicate the card is wired to host permanently
 - fsl,cd-internal : Indicate to use controller internal card detection
 - fsl,wp-internal : Indicate to use controller internal write protection
 - cd-gpios : Specify GPIOs for card detection
diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
index 89a0084..d64aea5 100644
--- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
@@ -10,7 +10,8 @@ Required properties:
 
 Optional properties:
 - gpios : may specify GPIOs in this order: Card-Detect GPIO,
-  Write-Protect GPIO.
+  Write-Protect GPIO. Note that this does not follow the
+  binding from mmc.txt, for historic reasons.
 - interrupts : the interrupt of a card detect interrupt.
 - interrupt-parent : the phandle for the interrupt controller that
   services interrupts for this device.
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt
new file mode 100644
index 0000000..6e70dcd
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/mmc.txt
@@ -0,0 +1,27 @@
+These properties are common to multiple MMC host controllers. Any host
+that requires the respective functionality should implement them using
+these definitions.
+
+Required properties:
+- bus-width: Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- cd-gpios : Specify GPIOs for card detection, see gpio binding
+- wp-gpios : Specify GPIOs for write protection, see gpio binding
+- cd-inverted: when present, polarity on the wp gpio line is inverted
+- wp-inverted: when present, polarity on the wp gpio line is inverted
+- non-removable: non-removable slot (like eMMC)
+- max-frequency: maximum operating clock frequency
+
+Example:
+
+sdhci@ab000000 {
+	compatible = "sdhci";
+	reg = <0xab000000 0x200>;
+	interrupts = <23>;
+	bus-width = <4>;
+	cd-gpios = <&gpio 69 0>;
+	cd-inverted;
+	wp-gpios = <&gpio 70 0>;
+	max-frequency = <50000000>;
+}
diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
index 7e51154..f77c303 100644
--- a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
+++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
@@ -7,12 +7,12 @@ Required properties:
 - compatible : Should be "nvidia,<chip>-sdhci"
 - reg : Should contain SD/MMC registers location and length
 - interrupts : Should contain SD/MMC interrupt
+- bus-width : Number of data lines, can be <1>, <4>, or <8>
 
 Optional properties:
 - cd-gpios : Specify GPIOs for card detection
 - wp-gpios : Specify GPIOs for write protection
 - power-gpios : Specify GPIOs for power control
-- support-8bit : Boolean, indicates if 8-bit mode should be used.
 
 Example:
 
@@ -23,5 +23,5 @@ sdhci@c8000200 {
 	cd-gpios = <&gpio 69 0>; /* gpio PI5 */
 	wp-gpios = <&gpio 57 0>; /* gpio PH1 */
 	power-gpios = <&gpio 155 0>; /* gpio PT3 */
-	support-8bit;
+	bus-width = <8>;
 };
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
index dbd4368..8a53958 100644
--- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -15,7 +15,7 @@ Optional properties:
 ti,dual-volt: boolean, supports dual voltage cards
 <supply-name>-supply: phandle to the regulator device tree node
 "supply-name" examples are "vmmc", "vmmc_aux" etc
-ti,bus-width: Number of data lines, default assumed is 1 if the property is missing.
+bus-width: Number of data lines, default assumed is 1 if the property is missing.
 cd-gpios: GPIOs for card detection
 wp-gpios: GPIOs for write protection
 ti,non-removable: non-removable slot (like eMMC)
@@ -27,7 +27,7 @@ Example:
 		reg = <0x4809c000 0x400>;
 		ti,hwmods = "mmc1";
 		ti,dual-volt;
-		ti,bus-width = <4>;
+		bus-width = <4>;
 		vmmc-supply = <&vmmc>; /* phandle to regulator node */
 		ti,non-removable;
 	};
diff --git a/Documentation/devicetree/bindings/usb/tegra-usb.txt b/Documentation/devicetree/bindings/usb/tegra-usb.txt
index 007005d..e9b005d 100644
--- a/Documentation/devicetree/bindings/usb/tegra-usb.txt
+++ b/Documentation/devicetree/bindings/usb/tegra-usb.txt
@@ -12,6 +12,9 @@ Required properties :
  - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
    activated for the bus to be powered.
 
+Required properties for phy_type == ulpi:
+  - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
+
 Optional properties:
   - dr_mode : dual role mode. Indicates the working mode for
    nvidia,tegra20-ehci compatible controllers.  Can be "host", "peripheral",