Merge 4.1-rc4 into tty-next

This resolves some tty driver merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

4 files changed, 35 insertions, 4 deletions

diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
index 974624e..161448d 100644
--- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
+++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
@@ -6,6 +6,7 @@ provided by Arteris.
 Required properties:
 - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
                Should be "ti,omap4-l3-noc" for OMAP4 family
+               Should be "ti,omap5-l3-noc" for OMAP5 family
 	       Should be "ti,dra7-l3-noc" for DRA7 family
                Should be "ti,am4372-l3-noc" for AM43 family
 - reg:	Contains L3 register address range for each noc domain.
diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
index a4873e5..e30e184 100644
--- a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
@@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 {
 		      80 81 68 69
 		      70 71 72 73
 		      74 75 76 77>;
-	interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+	interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
 			  "saif0", "saif1", "i2c0", "i2c1",
 			  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
 			  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
diff --git a/Documentation/devicetree/bindings/mtd/m25p80.txt b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
index f20b111..2bee681 100644
--- a/Documentation/devicetree/bindings/mtd/m25p80.txt
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt
@@ -8,8 +8,8 @@ Required properties:
                is not Linux-only, but in case of Linux, see the "m25p_ids"
                table in drivers/mtd/devices/m25p80.c for the list of supported
                chips.
-               Must also include "nor-jedec" for any SPI NOR flash that can be
-               identified by the JEDEC READ ID opcode (0x9F).
+               Must also include "jedec,spi-nor" for any SPI NOR flash that can
+               be identified by the JEDEC READ ID opcode (0x9F).
 - reg : Chip-Select number
 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
 
@@ -25,7 +25,7 @@ Example:
 	flash: m25p80@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80", "nor-jedec";
+		compatible = "spansion,m25p80", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 		m25p,fast-read;
diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
new file mode 100644
index 0000000..be78968
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
@@ -0,0 +1,30 @@
+Abracon ABX80X I2C ultra low power RTC/Alarm chip
+
+The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801,
+ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805
+is the superset of ab180x.
+
+Required properties:
+
+ - "compatible": should one of:
+        "abracon,abx80x"
+        "abracon,ab0801"
+        "abracon,ab0803"
+        "abracon,ab0804"
+        "abracon,ab0805"
+        "abracon,ab1801"
+        "abracon,ab1803"
+        "abracon,ab1804"
+        "abracon,ab1805"
+	Using "abracon,abx80x" will enable chip autodetection.
+ - "reg": I2C bus address of the device
+
+Optional properties:
+
+The abx804 and abx805 have a trickle charger that is able to charge the
+connected battery or supercap. Both the following properties have to be defined
+and valid to enable charging:
+
+ - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
+ - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
+                          resistor, the other values are in ohm.