Merge tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "Quite a lot of core work this time around, though not 100% successful.

  We gained support for runtime mode changes thanks to David Collins and
  improved support for write only regulators (ones where we can't read
  back the configuration) from Douglas Anderson.

  There's been quite a bit of work from Linus Walleij on converting from
  specfying GPIOs by numbers to descriptors. Sadly the testing turned
  out to be less good than we had hoped and so a lot of this had to be
  reverted.

  We also have the start of updates to use coupled regulators from
  Maciej Purski, unfortunately there are further problems there so the
  last couple of patches have been reverted.

  We also have new drivers for BD71837 and SY8106A devices, SAW
  regulators on Qualcomm SPMI and dropped support for some preproduction
  chips that never made it to market from the AB8500 driver"

* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
  regulator: gpio: Revert
  ARM: pxa, regulator: fix building ezx e680
  regulator: Revert coupled regulator support again
  regulator: wm8994: Fix shared GPIOs
  regulator: max77686: Fix shared GPIOs
  regulator: bd71837: BD71837 PMIC regulator driver
  regulator: bd71837: Devicetree bindings for BD71837 regulators
  regulator: gpio: Get enable GPIO using GPIO descriptor
  regulator: fixed: Convert to use GPIO descriptor only
  regulator: s2mps11: Fix boot on Odroid XU3
  dt-bindings: qcom_spmi: Document SAW support
  regulator: qcom_spmi: Add support for SAW
  regulator: tps65090: Pass descriptor instead of GPIO number
  regulator: s5m8767: Pass descriptor instead of GPIO number
  regulator: pfuze100: Delete reference to ena_gpio
  regulator: max8952: Pass descriptor instead of GPIO number
  regulator: lp8788-ldo: Pass descriptor instead of GPIO number
  regulator: lm363x: Pass descriptor instead of GPIO number
  regulator: max8973: Pass descriptor instead of GPIO number
  regulator: mc13xxx-core: Switch to SPDX identifier
  ...

1 files changed, 126 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
new file mode 100644
index 0000000..4edf313
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
@@ -0,0 +1,126 @@
+ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings
+
+BD71837MWV is a programmable Power Management
+IC (PMIC) for powering single-core, dual-core, and
+quad-core SoC’s such as NXP-i.MX 8M. It is optimized
+for low BOM cost and compact solution footprint. It
+integrates 8 Buck regulators and 7 LDO’s to provide all
+the power rails required by the SoC and the commonly
+used peripherals.
+
+Required properties:
+ - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7"
+
+List of regulators provided by this controller. BD71837 regulators node
+should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at
+Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
+Regulator nodes should be named to BUCK_<number> and LDO_<number>. The
+definition for each of these nodes is defined using the standard
+binding for regulators at
+Documentation/devicetree/bindings/regulator/regulator.txt.
+Note that if BD71837 starts at RUN state you probably want to use
+regulator-boot-on at least for BUCK6 and BUCK7 so that those are not
+disabled by driver at startup. LDO5 and LDO6 are supplied by those and
+if they are disabled at startup the voltage monitoring for LDO5/LDO6 will
+cause PMIC to reset.
+
+The valid names for regulator nodes are:
+BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8
+LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7
+
+Optional properties:
+- Any optional property defined in bindings/regulator/regulator.txt
+
+Example:
+regulators {
+	buck1: BUCK1 {
+		regulator-name = "buck1";
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-boot-on;
+		regulator-ramp-delay = <1250>;
+	};
+	buck2: BUCK2 {
+		regulator-name = "buck2";
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-ramp-delay = <1250>;
+	};
+	buck3: BUCK3 {
+		regulator-name = "buck3";
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-boot-on;
+	};
+	buck4: BUCK4 {
+		regulator-name = "buck4";
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-boot-on;
+	};
+	buck5: BUCK5 {
+		regulator-name = "buck5";
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1350000>;
+		regulator-boot-on;
+	};
+	buck6: BUCK6 {
+		regulator-name = "buck6";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+	buck7: BUCK7 {
+		regulator-name = "buck7";
+		regulator-min-microvolt = <1605000>;
+		regulator-max-microvolt = <1995000>;
+		regulator-boot-on;
+	};
+	buck8: BUCK8 {
+		regulator-name = "buck8";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1400000>;
+	};
+
+	ldo1: LDO1 {
+		regulator-name = "ldo1";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+	};
+	ldo2: LDO2 {
+		regulator-name = "ldo2";
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		regulator-boot-on;
+	};
+	ldo3: LDO3 {
+		regulator-name = "ldo3";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+	ldo4: LDO4 {
+		regulator-name = "ldo4";
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <1800000>;
+	};
+	ldo5: LDO5 {
+		regulator-name = "ldo5";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+	ldo6: LDO6 {
+		regulator-name = "ldo6";
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <1800000>;
+	};
+	ldo7_reg: LDO7 {
+		regulator-name = "ldo7";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+