Merge tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd

Pull MTD updates from Brian Norris:
 "General updates:
   - Cleanups and additional flash support for "dataflash" driver
   - new driver for mchp23k256 SPI SRAM device
   - improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
   - refactor and improve "sub-partition" handling with TRX partition
     parser; partitions can now be created as sub-partitions of another
     partition

  SPINOR updates, from Cyrille Pitchen and Marek Vasut:
   - introduce support to the SPI 1-2-2 and 1-4-4 protocols.
   - introduce support to the Double Data Rate (DDR) mode.
   - introduce support to the Octo SPI protocols.
   - add support to new memory parts for Spansion, Macronix and Winbond.
   - add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
   - clean up the st_spi_fsm driver.

  NAND updates, from Boris Brezillon:
   - addition of on-die ECC support to Micron driver
   - addition of helpers to help drivers choose most appropriate ECC
     settings
   - deletion of dead-code (cached programming and ->errstat() hook)
   - make sure drivers that do not support the SET/GET FEATURES command
     return ENOTSUPP use a dummy ->set/get_features implementation
     returning -ENOTSUPP (required for Micron on-die ECC)
   - change the semantic of ecc->write_page() for drivers setting the
     NAND_ECC_CUSTOM_PAGE_ACCESS flag
   - support exiting 'GET STATUS' command in default ->cmdfunc()
     implementations
   - change the prototype of ->setup_data_interface()

  A bunch of driver related changes:
   - various cleanup, fixes and improvements of the MTK driver
   - OMAP DT bindings fixes
   - support for ->setup_data_interface() in the fsmc driver
   - support for imx7 in the gpmi driver
   - finalization of the denali driver rework (thanks to Masahiro for
     the work he's done on this driver)
   - fix "bitflips in erased pages" handling in the ifc driver
   - addition of PM ops and dynamic timing configuration to the atmel
     driver"

* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
  Documentation: ABI: mtd: describe "offset" more precisely
  mtd: Fix check in mtd_unpoint()
  mtd: nand: mtk: release lock on error path
  mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
  mtd: spi-nor: cqspi: remove duplicate const
  mtd: spi-nor: Add support for Spansion S25FL064L
  mtd: spi-nor: Add support for mx66u51235f
  mtd: nand: mtk: add ->setup_data_interface() hook
  mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
  mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
  mtd: nand: mtk: disable ecc irq when writing page with hwecc
  mtd: nand: mtk: fix incorrect register setting order about ecc irq
  mtd: partitions: fixup some allocate_partition() whitespace
  mtd: parsers: trx: fix pr_err format for printing offset
  MAINTAINERS: Update SPI NOR subsystem git repositories
  mtd: extract TRX parser out of bcm47xxpart into a separated module
  mtd: partitions: add support for partition parsers
  mtd: partitions: add support for subpartitions
  mtd: partitions: rename "master" to the "parent" where appropriate
  mtd: partitions: remove sysfs files when deleting all master's partitions
  ...

10 files changed, 79 insertions, 15 deletions

diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt
index e593bbe..504291d 100644
--- a/Documentation/devicetree/bindings/mtd/denali-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt
@@ -3,10 +3,23 @@
 Required properties:
   - compatible : should be one of the following:
       "altr,socfpga-denali-nand"            - for Altera SOCFPGA
+      "socionext,uniphier-denali-nand-v5a"  - for Socionext UniPhier (v5a)
+      "socionext,uniphier-denali-nand-v5b"  - for Socionext UniPhier (v5b)
   - reg : should contain registers location and length for data and reg.
   - reg-names: Should contain the reg names "nand_data" and "denali_reg"
   - interrupts : The interrupt number.
 
+Optional properties:
+  - nand-ecc-step-size: see nand.txt for details.  If present, the value must be
+      512        for "altr,socfpga-denali-nand"
+      1024       for "socionext,uniphier-denali-nand-v5a"
+      1024       for "socionext,uniphier-denali-nand-v5b"
+  - nand-ecc-strength: see nand.txt for details.  Valid values are:
+      8, 15      for "altr,socfpga-denali-nand"
+      8, 16, 24  for "socionext,uniphier-denali-nand-v5a"
+      8, 16      for "socionext,uniphier-denali-nand-v5b"
+  - nand-ecc-maximize: see nand.txt for details
+
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
 
diff --git a/Documentation/devicetree/bindings/mtd/elm.txt b/Documentation/devicetree/bindings/mtd/elm.txt
index 8c1528c..59ddc61 100644
--- a/Documentation/devicetree/bindings/mtd/elm.txt
+++ b/Documentation/devicetree/bindings/mtd/elm.txt
@@ -1,7 +1,7 @@
 Error location module
 
 Required properties:
-- compatible: Must be "ti,am33xx-elm"
+- compatible: Must be "ti,am3352-elm"
 - reg: physical base address and size of the registers map.
 - interrupts: Interrupt number for the elm.
 
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
index 174f68c..dd55904 100644
--- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -5,7 +5,7 @@ the GPMC controller with a name of "nand".
 
 All timing relevant properties as well as generic gpmc child properties are
 explained in a separate documents - please refer to
-Documentation/devicetree/bindings/bus/ti-gpmc.txt
+Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 For NAND specific properties such as ECC modes or bus width, please refer to
 Documentation/devicetree/bindings/mtd/nand.txt
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt
index 4828c17..131d3a74 100644
--- a/Documentation/devicetree/bindings/mtd/gpmc-nor.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nor.txt
@@ -5,7 +5,7 @@ child nodes of the GPMC controller with a name of "nor".
 
 All timing relevant properties as well as generic GPMC child properties are
 explained in a separate documents. Please refer to
-Documentation/devicetree/bindings/bus/ti-gpmc.txt
+Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Required properties:
 - bank-width: 		Width of NOR flash in bytes. GPMC supports 8-bit and
@@ -28,7 +28,7 @@ Required properties:
 
 Optional properties:
 - gpmc,XXX		Additional GPMC timings and settings parameters. See
-			Documentation/devicetree/bindings/bus/ti-gpmc.txt
+			Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Optional properties for partition table parsing:
 - #address-cells: should be set to 1
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
index 5d8fa52..b6e8bfd 100644
--- a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
@@ -5,7 +5,7 @@ the GPMC controller with a name of "onenand".
 
 All timing relevant properties as well as generic gpmc child properties are
 explained in a separate documents - please refer to
-Documentation/devicetree/bindings/bus/ti-gpmc.txt
+Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Required properties:
 
diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
index d02acaf..b289ef3 100644
--- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
@@ -4,7 +4,12 @@ The GPMI nand controller provides an interface to control the
 NAND flash chips.
 
 Required properties:
-  - compatible : should be "fsl,<chip>-gpmi-nand"
+  - compatible : should be "fsl,<chip>-gpmi-nand", chip can be:
+    * imx23
+    * imx28
+    * imx6q
+    * imx6sx
+    * imx7d
   - reg : should contain registers location and length for gpmi and bch.
   - reg-names: Should contain the reg names "gpmi-nand" and "bch"
   - interrupts : BCH interrupt number.
@@ -13,6 +18,13 @@ Required properties:
     and GPMI DMA channel ID.
     Refer to dma.txt and fsl-mxs-dma.txt for details.
   - dma-names: Must be "rx-tx".
+  - clocks : clocks phandle and clock specifier corresponding to each clock
+    specified in clock-names.
+  - clock-names : The "gpmi_io" clock is always required. Which clocks are
+    exactly required depends on chip:
+    * imx23/imx28 : "gpmi_io"
+    * imx6q/sx : "gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch"
+    * imx7d : "gpmi_io", "gpmi_bch_apb"
 
 Optional properties:
   - nand-on-flash-bbt: boolean to enable on flash bbt option if not
diff --git a/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt b/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt
new file mode 100644
index 0000000..7328eb9
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/microchip,mchp23k256.txt
@@ -0,0 +1,18 @@
+* MTD SPI driver for Microchip 23K256 (and similar) serial SRAM
+
+Required properties:
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+  representing partitions.
+- compatible : Must be one of "microchip,mchp23k256" or "microchip,mchp23lcv1024"
+- reg : Chip-Select number
+- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
+
+Example:
+
+	spi-sram@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "microchip,mchp23k256";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
diff --git a/Documentation/devicetree/bindings/mtd/mtk-nand.txt b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
index 069c192..dbf9e05 100644
--- a/Documentation/devicetree/bindings/mtd/mtk-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/mtk-nand.txt
@@ -12,7 +12,8 @@ tree nodes.
 
 The first part of NFC is NAND Controller Interface (NFI) HW.
 Required NFI properties:
-- compatible:			Should be "mediatek,mtxxxx-nfc".
+- compatible:			Should be one of "mediatek,mt2701-nfc",
+				"mediatek,mt2712-nfc".
 - reg:				Base physical address and size of NFI.
 - interrupts:			Interrupts of NFI.
 - clocks:			NFI required clocks.
@@ -141,7 +142,7 @@ Example:
 ==============
 
 Required BCH properties:
-- compatible:	Should be "mediatek,mtxxxx-ecc".
+- compatible:	Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc".
 - reg:		Base physical address and size of ECC.
 - interrupts:	Interrupts of ECC.
 - clocks:	ECC required clocks.
diff --git a/Documentation/devicetree/bindings/mtd/nand.txt b/Documentation/devicetree/bindings/mtd/nand.txt
index b056016..133f381 100644
--- a/Documentation/devicetree/bindings/mtd/nand.txt
+++ b/Documentation/devicetree/bindings/mtd/nand.txt
@@ -21,7 +21,7 @@ Optional NAND chip properties:
 
 - nand-ecc-mode : String, operation mode of the NAND ecc mode.
 		  Supported values are: "none", "soft", "hw", "hw_syndrome",
-		  "hw_oob_first".
+		  "hw_oob_first", "on-die".
 		  Deprecated values:
 		  "soft_bch": use "soft" and nand-ecc-algo instead
 - nand-ecc-algo: string, algorithm of NAND ECC.
diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt
index 81a224d..36f3b76 100644
--- a/Documentation/devicetree/bindings/mtd/partition.txt
+++ b/Documentation/devicetree/bindings/mtd/partition.txt
@@ -1,29 +1,49 @@
-Representing flash partitions in devicetree
+Flash partitions in device tree
+===============================
 
-Partitions can be represented by sub-nodes of an mtd device. This can be used
+Flash devices can be partitioned into one or more functional ranges (e.g. "boot
+code", "nvram", "kernel").
+
+Different devices may be partitioned in a different ways. Some may use a fixed
+flash layout set at production time. Some may use on-flash table that describes
+the geometry and naming/purpose of each functional region. It is also possible
+to see these methods mixed.
+
+To assist system software in locating partitions, we allow describing which
+method is used for a given flash device. To describe the method there should be
+a subnode of the flash device that is named 'partitions'. It must have a
+'compatible' property, which is used to identify the method to use.
+
+We currently only document a binding for fixed layouts.
+
+
+Fixed Partitions
+================
+
+Partitions can be represented by sub-nodes of a flash device. This can be used
 on platforms which have strong conventions about which portions of a flash are
 used for what purposes, but which don't use an on-flash partition table such
 as RedBoot.
 
-The partition table should be a subnode of the mtd node and should be named
+The partition table should be a subnode of the flash node and should be named
 'partitions'. This node should have the following property:
 - compatible : (required) must be "fixed-partitions"
 Partitions are then defined in subnodes of the partitions node.
 
-For backwards compatibility partitions as direct subnodes of the mtd device are
+For backwards compatibility partitions as direct subnodes of the flash device are
 supported. This use is discouraged.
 NOTE: also for backwards compatibility, direct subnodes that have a compatible
 string are not considered partitions, as they may be used for other bindings.
 
 #address-cells & #size-cells must both be present in the partitions subnode of the
-mtd device. There are two valid values for both:
+flash device. There are two valid values for both:
 <1>: for partitions that require a single 32-bit cell to represent their
      size/address (aka the value is below 4 GiB)
 <2>: for partitions that require two 32-bit cells to represent their
      size/address (aka the value is 4 GiB or greater).
 
 Required properties:
-- reg : The partition's offset and size within the mtd bank.
+- reg : The partition's offset and size within the flash
 
 Optional properties:
 - label : The label / name for this partition.  If omitted, the label is taken