USB: ark3116: Make existing functions 16450-aware and add close and release functions.

Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Cc: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

1 files changed, 276 insertions, 219 deletions

diff --git a/drivers/usb/serial/ark3116.c b/drivers/usb/serial/ark3116.c
index 5c94741..d12df94 100644
--- a/drivers/usb/serial/ark3116.c
+++ b/drivers/usb/serial/ark3116.c
@@ -152,79 +152,105 @@ static inline void ARK3116_RCV_QUIET(struct usb_serial *serial,
 			buf, 0x0000001, 1000);
 }
 
+static inline int calc_divisor(int bps)
+{
+	/* Original ark3116 made some exceptions in rounding here
+	 * because windows did the same. Assume that is not really
+	 * necessary.
+	 * Crystal is 12MHz, probably because of USB, but we divide by 4?
+	 */
+	return (12000000 + 2*bps) / (4*bps);
+}
+
 static int ark3116_attach(struct usb_serial *serial)
 {
-	char *buf;
+	struct usb_serial_port *port = serial->port[0];
+	struct ark3116_private *priv;
+
+	/* make sure we have our end-points */
+	if ((serial->num_bulk_in == 0) ||
+	    (serial->num_bulk_out == 0) ||
+	    (serial->num_interrupt_in == 0)) {
+		dev_err(&serial->dev->dev,
+			"%s - missing endpoint - "
+			"bulk in: %d, bulk out: %d, int in %d\n",
+			KBUILD_MODNAME,
+			serial->num_bulk_in,
+			serial->num_bulk_out,
+			serial->num_interrupt_in);
+		return -EINVAL;
+	}
 
-	buf = kmalloc(1, GFP_KERNEL);
-	if (!buf) {
-		dbg("error kmalloc -> out of mem?");
+	priv = kzalloc(sizeof(struct ark3116_private),
+		       GFP_KERNEL);
+	if (!priv)
 		return -ENOMEM;
-	}
 
-	if (is_irda(serial))
-		dbg("IrDA mode");
+	init_waitqueue_head(&priv->delta_msr_wait);
+	mutex_init(&priv->hw_lock);
+	spin_lock_init(&priv->status_lock);
+
+	priv->irda = is_irda(serial);
+
+	usb_set_serial_port_data(port, priv);
 
-	/* 3 */
-	ARK3116_SND(serial, 3, 0xFE, 0x40, 0x0008, 0x0002);
-	ARK3116_SND(serial, 4, 0xFE, 0x40, 0x0008, 0x0001);
-	ARK3116_SND(serial, 5, 0xFE, 0x40, 0x0000, 0x0008);
-	ARK3116_SND(serial, 6, 0xFE, 0x40, is_irda(serial) ? 0x0001 : 0x0000,
-		    0x000B);
+	/* setup the hardware */
+	ark3116_write_reg(serial, UART_IER, 0);
+	/* disable DMA */
+	ark3116_write_reg(serial, UART_FCR, 0);
+	/* handshake control */
+	priv->hcr = 0;
+	ark3116_write_reg(serial, 0x8     , 0);
+	/* modem control */
+	priv->mcr = 0;
+	ark3116_write_reg(serial, UART_MCR, 0);
 
-	if (is_irda(serial)) {
-		ARK3116_SND(serial, 1001, 0xFE, 0x40, 0x0000, 0x000C);
-		ARK3116_SND(serial, 1002, 0xFE, 0x40, 0x0041, 0x000D);
-		ARK3116_SND(serial, 1003, 0xFE, 0x40, 0x0001, 0x000A);
+	if (!(priv->irda)) {
+		ark3116_write_reg(serial, 0xb , 0);
+	} else {
+		ark3116_write_reg(serial, 0xb , 1);
+		ark3116_write_reg(serial, 0xc , 0);
+		ark3116_write_reg(serial, 0xd , 0x41);
+		ark3116_write_reg(serial, 0xa , 1);
 	}
 
-	/* <-- seq7 */
-	ARK3116_RCV(serial,  7, 0xFE, 0xC0, 0x0000, 0x0003, 0x00, buf);
-	ARK3116_SND(serial,  8, 0xFE, 0x40, 0x0080, 0x0003);
-	ARK3116_SND(serial,  9, 0xFE, 0x40, 0x001A, 0x0000);
-	ARK3116_SND(serial, 10, 0xFE, 0x40, 0x0000, 0x0001);
-	ARK3116_SND(serial, 11, 0xFE, 0x40, 0x0000, 0x0003);
-
-	/* <-- seq12 */
-	ARK3116_RCV(serial, 12, 0xFE, 0xC0, 0x0000, 0x0004, 0x00, buf);
-	ARK3116_SND(serial, 13, 0xFE, 0x40, 0x0000, 0x0004);
-
-	/* 14 */
-	ARK3116_RCV(serial, 14, 0xFE, 0xC0, 0x0000, 0x0004, 0x00, buf);
-	ARK3116_SND(serial, 15, 0xFE, 0x40, 0x0000, 0x0004);
-
-	/* 16 */
-	ARK3116_RCV(serial, 16, 0xFE, 0xC0, 0x0000, 0x0004, 0x00, buf);
-	/* --> seq17 */
-	ARK3116_SND(serial, 17, 0xFE, 0x40, 0x0001, 0x0004);
-
-	/* <-- seq18 */
-	ARK3116_RCV(serial, 18, 0xFE, 0xC0, 0x0000, 0x0004, 0x01, buf);
-
-	/* --> seq19 */
-	ARK3116_SND(serial, 19, 0xFE, 0x40, 0x0003, 0x0004);
-
-	/* <-- seq20 */
-	/* seems like serial port status info (RTS, CTS, ...) */
-	/* returns modem control line status?! */
-	ARK3116_RCV(serial, 20, 0xFE, 0xC0, 0x0000, 0x0006, 0xFF, buf);
-
-	/* set 9600 baud & do some init?! */
-	ARK3116_SND(serial, 147, 0xFE, 0x40, 0x0083, 0x0003);
-	ARK3116_SND(serial, 148, 0xFE, 0x40, 0x0038, 0x0000);
-	ARK3116_SND(serial, 149, 0xFE, 0x40, 0x0001, 0x0001);
-	if (is_irda(serial))
-		ARK3116_SND(serial, 1004, 0xFE, 0x40, 0x0000, 0x0009);
-	ARK3116_SND(serial, 150, 0xFE, 0x40, 0x0003, 0x0003);
-	ARK3116_RCV(serial, 151, 0xFE, 0xC0, 0x0000, 0x0004, 0x03, buf);
-	ARK3116_SND(serial, 152, 0xFE, 0x40, 0x0000, 0x0003);
-	ARK3116_RCV(serial, 153, 0xFE, 0xC0, 0x0000, 0x0003, 0x00, buf);
-	ARK3116_SND(serial, 154, 0xFE, 0x40, 0x0003, 0x0003);
+	/* setup baudrate */
+	ark3116_write_reg(serial, UART_LCR, UART_LCR_DLAB);
 
-	kfree(buf);
+	/* setup for 9600 8N1 */
+	priv->quot = calc_divisor(9600);
+	ark3116_write_reg(serial, UART_DLL, priv->quot & 0xff);
+	ark3116_write_reg(serial, UART_DLM, (priv->quot>>8) & 0xff);
+
+	priv->lcr = UART_LCR_WLEN8;
+	ark3116_write_reg(serial, UART_LCR, UART_LCR_WLEN8);
+
+	ark3116_write_reg(serial, 0xe, 0);
+
+	if (priv->irda)
+		ark3116_write_reg(serial, 0x9, 0);
+
+	dev_info(&serial->dev->dev,
+		"%s using %s mode\n",
+		KBUILD_MODNAME,
+		priv->irda ? "IrDA" : "RS232");
 	return 0;
 }
 
+static void ark3116_release(struct usb_serial *serial)
+{
+	struct usb_serial_port *port = serial->port[0];
+	struct ark3116_private *priv = usb_get_serial_port_data(port);
+
+	/* device is closed, so URBs and DMA should be down */
+
+	usb_set_serial_port_data(port, NULL);
+
+	mutex_destroy(&priv->hw_lock);
+
+	kfree(priv);
+}
+
 static void ark3116_init_termios(struct tty_struct *tty)
 {
 	struct ktermios *termios = tty->termios;
@@ -240,200 +266,189 @@ static void ark3116_set_termios(struct tty_struct *tty,
 				struct ktermios *old_termios)
 {
 	struct usb_serial *serial = port->serial;
+	struct ark3116_private *priv = usb_get_serial_port_data(port);
 	struct ktermios *termios = tty->termios;
 	unsigned int cflag = termios->c_cflag;
-	int baud;
-	int ark3116_baud;
-	char *buf;
-	char config;
-
-	config = 0;
+	int bps = tty_get_baud_rate(tty);
+	int quot;
+	__u8 lcr, hcr, eval;
+
+	/* set data bit count */
+	switch (cflag & CSIZE) {
+	case CS5:
+		lcr = UART_LCR_WLEN5;
+		break;
+	case CS6:
+		lcr = UART_LCR_WLEN6;
+		break;
+	case CS7:
+		lcr = UART_LCR_WLEN7;
+		break;
+	default:
+	case CS8:
+		lcr = UART_LCR_WLEN8;
+		break;
+	}
+	if (cflag & CSTOPB)
+		lcr |= UART_LCR_STOP;
+	if (cflag & PARENB)
+		lcr |= UART_LCR_PARITY;
+	if (!(cflag & PARODD))
+		lcr |= UART_LCR_EPAR;
+#ifdef CMSPAR
+	if (cflag & CMSPAR)
+		lcr |= UART_LCR_SPAR;
+#endif
+	/* handshake control */
+	hcr = (cflag & CRTSCTS) ? 0x03 : 0x00;
+
+	/* calc baudrate */
+	dbg("%s - setting bps to %d", __func__, bps);
+	eval = 0;
+	switch (bps) {
+	case 0:
+		quot = calc_divisor(9600);
+		break;
+	default:
+		if ((bps < 75) || (bps > 3000000))
+			bps = 9600;
+		quot = calc_divisor(bps);
+		break;
+	case 460800:
+		eval = 1;
+		quot = calc_divisor(bps);
+		break;
+	case 921600:
+		eval = 2;
+		quot = calc_divisor(bps);
+		break;
+	}
 
-	dbg("%s - port %d", __func__, port->number);
+	/* Update state: synchronize */
+	mutex_lock(&priv->hw_lock);
 
+	/* keep old LCR_SBC bit */
+	lcr |= (priv->lcr & UART_LCR_SBC);
 
-	cflag = termios->c_cflag;
-	termios->c_cflag &= ~(CMSPAR|CRTSCTS);
+	dbg("%s - setting hcr:0x%02x,lcr:0x%02x,quot:%d",
+	    __func__, hcr, lcr, quot);
 
-	buf = kmalloc(1, GFP_KERNEL);
-	if (!buf) {
-		dbg("error kmalloc");
-		*termios = *old_termios;
-		return;
+	/* handshake control */
+	if (priv->hcr != hcr) {
+		priv->hcr = hcr;
+		ark3116_write_reg(serial, 0x8, hcr);
 	}
 
-	/* set data bit count (8/7/6/5) */
-	if (cflag & CSIZE) {
-		switch (cflag & CSIZE) {
-		case CS5:
-			config |= 0x00;
-			dbg("setting CS5");
-			break;
-		case CS6:
-			config |= 0x01;
-			dbg("setting CS6");
-			break;
-		case CS7:
-			config |= 0x02;
-			dbg("setting CS7");
-			break;
-		default:
-			dbg("CSIZE was set but not CS5-CS8, using CS8!");
-			/* fall through */
-		case CS8:
-			config |= 0x03;
-			dbg("setting CS8");
-			break;
-		}
+	/* baudrate */
+	if (priv->quot != quot) {
+		priv->quot = quot;
+		priv->lcr = lcr; /* need to write lcr anyway */
+
+		/* disable DMA since transmit/receive is
+		 * shadowed by UART_DLL
+		 */
+		ark3116_write_reg(serial, UART_FCR, 0);
+
+		ark3116_write_reg(serial, UART_LCR,
+				  lcr|UART_LCR_DLAB);
+		ark3116_write_reg(serial, UART_DLL, quot & 0xff);
+		ark3116_write_reg(serial, UART_DLM, (quot>>8) & 0xff);
+
+		/* restore lcr */
+		ark3116_write_reg(serial, UART_LCR, lcr);
+		/* magic baudrate thingy: not sure what it does,
+		 * but windows does this as well.
+		 */
+		ark3116_write_reg(serial, 0xe, eval);
+
+		/* enable DMA */
+		ark3116_write_reg(serial, UART_FCR, UART_FCR_DMA_SELECT);
+	} else if (priv->lcr != lcr) {
+		priv->lcr = lcr;
+		ark3116_write_reg(serial, UART_LCR, lcr);
 	}
 
-	/* set parity (NONE/EVEN/ODD) */
-	if (cflag & PARENB) {
-		if (cflag & PARODD) {
-			config |= 0x08;
-			dbg("setting parity to ODD");
-		} else {
-			config |= 0x18;
-			dbg("setting parity to EVEN");
-		}
-	} else {
-		dbg("setting parity to NONE");
-	}
+	mutex_unlock(&priv->hw_lock);
 
-	/* set stop bit (1/2) */
-	if (cflag & CSTOPB) {
-		config |= 0x04;
-		dbg("setting 2 stop bits");
-	} else {
-		dbg("setting 1 stop bit");
+	/* check for software flow control */
+	if (I_IXOFF(tty) || I_IXON(tty)) {
+		dev_warn(&serial->dev->dev,
+			 "%s: don't know how to do software flow control\n",
+			 KBUILD_MODNAME);
 	}
 
-	/* set baudrate */
-	baud = tty_get_baud_rate(tty);
-
-	switch (baud) {
-	case 75:
-	case 150:
-	case 300:
-	case 600:
-	case 1200:
-	case 1800:
-	case 2400:
-	case 4800:
-	case 9600:
-	case 19200:
-	case 38400:
-	case 57600:
-	case 115200:
-	case 230400:
-	case 460800:
-		/* Report the resulting rate back to the caller */
-		tty_encode_baud_rate(tty, baud, baud);
-		break;
-	/* set 9600 as default (if given baudrate is invalid for example) */
-	default:
-		tty_encode_baud_rate(tty, 9600, 9600);
-	case 0:
-		baud = 9600;
-	}
-
-	/*
-	 * found by try'n'error, be careful, maybe there are other options
-	 * for multiplicator etc! (3.5 for example)
-	 */
-	if (baud == 460800)
-		/* strange, for 460800 the formula is wrong
-		 * if using round() then 9600baud is wrong) */
-		ark3116_baud = 7;
-	else
-		ark3116_baud = 3000000 / baud;
-
-	/* ? */
-	ARK3116_RCV(serial, 0, 0xFE, 0xC0, 0x0000, 0x0003, 0x03, buf);
-
-	/* offset = buf[0]; */
-	/* offset = 0x03; */
-	/* dbg("using 0x%04X as target for 0x0003:", 0x0080 + offset); */
-
-	/* set baudrate */
-	dbg("setting baudrate to %d (->reg=%d)", baud, ark3116_baud);
-	ARK3116_SND(serial, 147, 0xFE, 0x40, 0x0083, 0x0003);
-	ARK3116_SND(serial, 148, 0xFE, 0x40,
-			    (ark3116_baud & 0x00FF), 0x0000);
-	ARK3116_SND(serial, 149, 0xFE, 0x40,
-			    (ark3116_baud & 0xFF00) >> 8, 0x0001);
-	ARK3116_SND(serial, 150, 0xFE, 0x40, 0x0003, 0x0003);
-
-	/* ? */
-	ARK3116_RCV(serial, 151, 0xFE, 0xC0, 0x0000, 0x0004, 0x03, buf);
-	ARK3116_SND(serial, 152, 0xFE, 0x40, 0x0000, 0x0003);
-
-	/* set data bit count, stop bit count & parity: */
-	dbg("updating bit count, stop bit or parity (cfg=0x%02X)", config);
-	ARK3116_RCV(serial, 153, 0xFE, 0xC0, 0x0000, 0x0003, 0x00, buf);
-	ARK3116_SND(serial, 154, 0xFE, 0x40, config, 0x0003);
+	/* Don't rewrite B0 */
+	if (tty_termios_baud_rate(termios))
+		tty_termios_encode_baud_rate(termios, bps, bps);
+}
 
-	if (cflag & CRTSCTS)
-		dbg("CRTSCTS not supported by chipset?!");
+static void ark3116_close(struct usb_serial_port *port)
+{
+	struct usb_serial *serial = port->serial;
 
-	/* TEST ARK3116_SND(154, 0xFE, 0x40, 0xFFFF, 0x0006); */
+	if (serial->dev) {
+		/* disable DMA */
+		ark3116_write_reg(serial, UART_FCR, 0);
 
-	kfree(buf);
+		/* deactivate interrupts */
+		ark3116_write_reg(serial, UART_IER, 0);
 
-	return;
+		/* shutdown any bulk reads that might be going on */
+		if (serial->num_bulk_out)
+			usb_kill_urb(port->write_urb);
+		if (serial->num_bulk_in)
+			usb_kill_urb(port->read_urb);
+		if (serial->num_interrupt_in)
+			usb_kill_urb(port->interrupt_in_urb);
+	}
 }
 
 static int ark3116_open(struct tty_struct *tty, struct usb_serial_port *port)
 {
-	struct ktermios tmp_termios;
+	struct ark3116_private *priv = usb_get_serial_port_data(port);
 	struct usb_serial *serial = port->serial;
-	char *buf;
-	int result = 0;
-
-	dbg("%s - port %d", __func__, port->number);
+	unsigned char *buf;
+	int result;
 
 	buf = kmalloc(1, GFP_KERNEL);
-	if (!buf) {
-		dbg("error kmalloc -> out of mem?");
+	if (buf == NULL)
 		return -ENOMEM;
-	}
 
 	result = usb_serial_generic_open(tty, port);
-	if (result)
+	if (result) {
+		dbg("%s - usb_serial_generic_open failed: %d",
+		    __func__, result);
 		goto err_out;
+	}
 
-	/* open */
-	ARK3116_RCV(serial, 111, 0xFE, 0xC0, 0x0000, 0x0003, 0x02, buf);
-
-	ARK3116_SND(serial, 112, 0xFE, 0x40, 0x0082, 0x0003);
-	ARK3116_SND(serial, 113, 0xFE, 0x40, 0x001A, 0x0000);
-	ARK3116_SND(serial, 114, 0xFE, 0x40, 0x0000, 0x0001);
-	ARK3116_SND(serial, 115, 0xFE, 0x40, 0x0002, 0x0003);
-
-	ARK3116_RCV(serial, 116, 0xFE, 0xC0, 0x0000, 0x0004, 0x03, buf);
-	ARK3116_SND(serial, 117, 0xFE, 0x40, 0x0002, 0x0004);
-
-	ARK3116_RCV(serial, 118, 0xFE, 0xC0, 0x0000, 0x0004, 0x02, buf);
-	ARK3116_SND(serial, 119, 0xFE, 0x40, 0x0000, 0x0004);
-
-	ARK3116_RCV(serial, 120, 0xFE, 0xC0, 0x0000, 0x0004, 0x00, buf);
+	/* setup termios */
+	if (tty)
+		ark3116_set_termios(tty, port, NULL);
 
-	ARK3116_SND(serial, 121, 0xFE, 0x40, 0x0001, 0x0004);
+	/* remove any data still left: also clears error state */
+	ark3116_read_reg(serial, UART_RX, buf);
 
-	ARK3116_RCV(serial, 122, 0xFE, 0xC0, 0x0000, 0x0004, 0x01, buf);
+	/* read modem status */
+	priv->msr = ark3116_read_reg(serial, UART_MSR, buf);
+	/* read line status */
+	priv->lsr = ark3116_read_reg(serial, UART_LSR, buf);
 
-	ARK3116_SND(serial, 123, 0xFE, 0x40, 0x0003, 0x0004);
+	result = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
+	if (result) {
+		dev_err(&port->dev, "submit irq_in urb failed %d\n",
+			result);
+		ark3116_close(port);
+		goto err_out;
+	}
 
-	/* returns different values (control lines?!) */
-	ARK3116_RCV(serial, 124, 0xFE, 0xC0, 0x0000, 0x0006, 0xFF, buf);
+	/* activate interrupts */
+	ark3116_write_reg(port->serial, UART_IER, UART_IER_MSI|UART_IER_RLSI);
 
-	/* initialise termios */
-	if (tty)
-		ark3116_set_termios(tty, port, &tmp_termios);
+	/* enable DMA */
+	ark3116_write_reg(port->serial, UART_FCR, UART_FCR_DMA_SELECT);
 
 err_out:
 	kfree(buf);
-
 	return result;
 }
 
@@ -441,6 +456,7 @@ static int ark3116_ioctl(struct tty_struct *tty, struct file *file,
 			 unsigned int cmd, unsigned long arg)
 {
 	struct usb_serial_port *port = tty->driver_data;
+	struct ark3116_private *priv = usb_get_serial_port_data(port);
 	struct serial_struct serstruct;
 	void __user *user_arg = (void __user *)arg;
 
@@ -462,9 +478,48 @@ static int ark3116_ioctl(struct tty_struct *tty, struct file *file,
 		if (copy_from_user(&serstruct, user_arg, sizeof(serstruct)))
 			return -EFAULT;
 		return 0;
-	default:
-		dbg("%s cmd 0x%04x not supported", __func__, cmd);
+	case TIOCMIWAIT:
+		for (;;) {
+			struct async_icount prev = priv->icount;
+			interruptible_sleep_on(&priv->delta_msr_wait);
+			/* see if a signal did it */
+			if (signal_pending(current))
+				return -ERESTARTSYS;
+			if ((prev.rng == priv->icount.rng) &&
+			    (prev.dsr == priv->icount.dsr) &&
+			    (prev.dcd == priv->icount.dcd) &&
+			    (prev.cts == priv->icount.cts))
+				return -EIO;
+			if ((arg & TIOCM_RNG &&
+			     (prev.rng != priv->icount.rng)) ||
+			    (arg & TIOCM_DSR &&
+			     (prev.dsr != priv->icount.dsr)) ||
+			    (arg & TIOCM_CD  &&
+			     (prev.dcd != priv->icount.dcd)) ||
+			    (arg & TIOCM_CTS &&
+			     (prev.cts != priv->icount.cts)))
+				return 0;
+		}
 		break;
+	case TIOCGICOUNT: {
+		struct serial_icounter_struct icount;
+		struct async_icount cnow = priv->icount;
+		memset(&icount, 0, sizeof(icount));
+		icount.cts = cnow.cts;
+		icount.dsr = cnow.dsr;
+		icount.rng = cnow.rng;
+		icount.dcd = cnow.dcd;
+		icount.rx = cnow.rx;
+		icount.tx = cnow.tx;
+		icount.frame = cnow.frame;
+		icount.overrun = cnow.overrun;
+		icount.parity = cnow.parity;
+		icount.brk = cnow.brk;
+		icount.buf_overrun = cnow.buf_overrun;
+		if (copy_to_user(user_arg, &icount, sizeof(icount)))
+			return -EFAULT;
+		return 0;
+	}
 	}
 
 	return -ENOIOCTLCMD;
@@ -518,11 +573,13 @@ static struct usb_serial_driver ark3116_device = {
 	.usb_driver =		&ark3116_driver,
 	.num_ports =		1,
 	.attach =		ark3116_attach,
+	.release =		ark3116_release,
 	.set_termios =		ark3116_set_termios,
 	.init_termios =		ark3116_init_termios,
 	.ioctl =		ark3116_ioctl,
 	.tiocmget =		ark3116_tiocmget,
 	.open =			ark3116_open,
+	.close =		ark3116_close,
 };
 
 static int __init ark3116_init(void)