summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
authorJan Kundrát <jan.kundrat@cesnet.cz>2017-12-22 22:47:16 +0100
committerWolfram Sang <wsa@the-dreams.de>2018-01-04 01:02:55 +0100
commitf11a04464ae57e8db1bb7634547842b43e36a898 (patch)
tree0759e0b693700075bf17546dc40d68a31993c8d1
parentf6762cedbef91ad1da338538efa811856a717d57 (diff)
downloadop-kernel-dev-f11a04464ae57e8db1bb7634547842b43e36a898.zip
op-kernel-dev-f11a04464ae57e8db1bb7634547842b43e36a898.tar.gz
i2c: gpio: Enable working over slow can_sleep GPIOs
"Slow" GPIOs (usually those connected over an SPI or an I2C bus) are, well, slow in their operation. It is generally a good idea to avoid using them for time-critical operation, but sometimes the hardware just sucks, and the software has to cope. In addition to that, the I2C bus itself does not actually define any strict timing limits; the bus is free to go all the way down to DC. The timeouts (and therefore the slowest acceptable frequency) are present only in SMBus. The `can_sleep` is IMHO a wrong concept to use here. My SPI-to-quad-UART chip (MAX14830) is connected via a 26MHz SPI bus, and it happily drives SCL at 200kHz (5µs pulses) during my benchmarks. That's faster than the maximal allowed speed of the traditional I2C. The previous version of this code did not really block operation over slow GPIO pins, anyway. Instead, it just resorted to printing a warning with a backtrace each time a GPIO pin was accessed, thereby slowing things down even more. Finally, it's not just me. A similar patch was originally submitted in 2015 [1]. [1] https://patchwork.ozlabs.org/patch/450956/ Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-rw-r--r--drivers/i2c/busses/i2c-gpio.c11
1 files changed, 7 insertions, 4 deletions
diff --git a/drivers/i2c/busses/i2c-gpio.c b/drivers/i2c/busses/i2c-gpio.c
index 3312ef9..58abb3e 100644
--- a/drivers/i2c/busses/i2c-gpio.c
+++ b/drivers/i2c/busses/i2c-gpio.c
@@ -39,7 +39,7 @@ static void i2c_gpio_setsda_val(void *data, int state)
{
struct i2c_gpio_private_data *priv = data;
- gpiod_set_value(priv->sda, state);
+ gpiod_set_value_cansleep(priv->sda, state);
}
/*
@@ -52,21 +52,21 @@ static void i2c_gpio_setscl_val(void *data, int state)
{
struct i2c_gpio_private_data *priv = data;
- gpiod_set_value(priv->scl, state);
+ gpiod_set_value_cansleep(priv->scl, state);
}
static int i2c_gpio_getsda(void *data)
{
struct i2c_gpio_private_data *priv = data;
- return gpiod_get_value(priv->sda);
+ return gpiod_get_value_cansleep(priv->sda);
}
static int i2c_gpio_getscl(void *data)
{
struct i2c_gpio_private_data *priv = data;
- return gpiod_get_value(priv->scl);
+ return gpiod_get_value_cansleep(priv->scl);
}
#ifdef CONFIG_I2C_GPIO_FAULT_INJECTOR
@@ -286,6 +286,9 @@ static int i2c_gpio_probe(struct platform_device *pdev)
if (IS_ERR(priv->scl))
return PTR_ERR(priv->scl);
+ if (gpiod_cansleep(priv->sda) || gpiod_cansleep(priv->scl))
+ dev_warn(dev, "Slow GPIO pins might wreak havoc into I2C/SMBus bus timing");
+
bit_data->setsda = i2c_gpio_setsda_val;
bit_data->setscl = i2c_gpio_setscl_val;
OpenPOWER on IntegriCloud