[SCSI] cxgb3i: Add cxgb3i iSCSI driver.

This patch implements the cxgb3i iscsi connection acceleration for the
open-iscsi initiator.

The cxgb3i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

14 files changed, 4873 insertions, 0 deletions

diff --git a/Documentation/scsi/cxgb3i.txt b/Documentation/scsi/cxgb3i.txt
new file mode 100644
index 0000000..8141fa0
--- /dev/null
+++ b/Documentation/scsi/cxgb3i.txt
@@ -0,0 +1,85 @@
+Chelsio S3 iSCSI Driver for Linux
+
+Introduction
+============
+
+The Chelsio T3 ASIC based Adapters (S310, S320, S302, S304, Mezz cards, etc.
+series of products) supports iSCSI acceleration and iSCSI Direct Data Placement
+(DDP) where the hardware handles the expensive byte touching operations, such
+as CRC computation and verification, and direct DMA to the final host memory
+destination:
+
+	- iSCSI PDU digest generation and verification
+
+	  On transmitting, Chelsio S3 h/w computes and inserts the Header and
+	  Data digest into the PDUs.
+	  On receiving, Chelsio S3 h/w computes and verifies the Header and
+	  Data digest of the PDUs.
+
+	- Direct Data Placement (DDP)
+
+	  S3 h/w can directly place the iSCSI Data-In or Data-Out PDU's
+	  payload into pre-posted final destination host-memory buffers based
+	  on the Initiator Task Tag (ITT) in Data-In or Target Task Tag (TTT)
+	  in Data-Out PDUs.
+
+	- PDU Transmit and Recovery
+
+	  On transmitting, S3 h/w accepts the complete PDU (header + data)
+	  from the host driver, computes and inserts the digests, decomposes
+	  the PDU into multiple TCP segments if necessary, and transmit all
+	  the TCP segments onto the wire. It handles TCP retransmission if
+	  needed.
+
+	  On receving, S3 h/w recovers the iSCSI PDU by reassembling TCP
+	  segments, separating the header and data, calculating and verifying
+	  the digests, then forwards the header to the host. The payload data,
+	  if possible, will be directly placed into the pre-posted host DDP
+	  buffer. Otherwise, the payload data will be sent to the host too.
+
+The cxgb3i driver interfaces with open-iscsi initiator and provides the iSCSI
+acceleration through Chelsio hardware wherever applicable.
+
+Using the cxgb3i Driver
+=======================
+
+The following steps need to be taken to accelerates the open-iscsi initiator:
+
+1. Load the cxgb3i driver: "modprobe cxgb3i"
+
+   The cxgb3i module registers a new transport class "cxgb3i" with open-iscsi.
+
+   * in the case of recompiling the kernel, the cxgb3i selection is located at
+	Device Drivers
+		SCSI device support --->
+			[*] SCSI low-level drivers  --->
+				<M>   Chelsio S3xx iSCSI support
+
+2. Create an interface file located under /etc/iscsi/ifaces/ for the new
+   transport class "cxgb3i".
+
+   The content of the file should be in the following format:
+	iface.transport_name = cxgb3i
+	iface.net_ifacename = <ethX>
+	iface.ipaddress = <iscsi ip address>
+
+   * if iface.ipaddress is specified, <iscsi ip address> needs to be either the
+	same as the ethX's ip address or an address on the same subnet. Make
+	sure the ip address is unique in the network.
+
+3. edit /etc/iscsi/iscsid.conf
+   The default setting for MaxRecvDataSegmentLength (131072) is too big,
+   replace "node.conn[0].iscsi.MaxRecvDataSegmentLength" to be a value no
+   bigger than 15360 (for example 8192):
+
+	node.conn[0].iscsi.MaxRecvDataSegmentLength = 8192
+
+   * The login would fail for a normal session if MaxRecvDataSegmentLength is
+	too big.  A error message in the format of
+	"cxgb3i: ERR! MaxRecvSegmentLength <X> too big. Need to be <= <Y>."
+	would be logged to dmesg.
+
+4. To direct open-iscsi traffic to go through cxgb3i's accelerated path,
+   "-I <iface file name>" option needs to be specified with most of the
+   iscsiadm command. <iface file name> is the transport interface file created
+   in step 2.
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig
index 673463e..0e5e084 100644
--- a/drivers/scsi/Kconfig
+++ b/drivers/scsi/Kconfig
@@ -352,6 +352,8 @@ config ISCSI_TCP
 
 	 http://open-iscsi.org
 
+source "drivers/scsi/cxgb3i/Kconfig"
+
 config SGIWD93_SCSI
 	tristate "SGI WD93C93 SCSI Driver"
 	depends on SGI_HAS_WD93 && SCSI
diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile
index 07d0f58..1410697 100644
--- a/drivers/scsi/Makefile
+++ b/drivers/scsi/Makefile
@@ -126,6 +126,7 @@ obj-$(CONFIG_SCSI_HPTIOP)	+= hptiop.o
 obj-$(CONFIG_SCSI_STEX)		+= stex.o
 obj-$(CONFIG_SCSI_MVSAS)	+= mvsas.o
 obj-$(CONFIG_PS3_ROM)		+= ps3rom.o
+obj-$(CONFIG_SCSI_CXGB3_ISCSI)	+= libiscsi.o libiscsi_tcp.o cxgb3i/
 
 obj-$(CONFIG_ARM)		+= arm/
 
diff --git a/drivers/scsi/cxgb3i/Kbuild b/drivers/scsi/cxgb3i/Kbuild
new file mode 100644
index 0000000..ee7d6d2
--- /dev/null
+++ b/drivers/scsi/cxgb3i/Kbuild
@@ -0,0 +1,4 @@
+EXTRA_CFLAGS += -I$(TOPDIR)/drivers/net/cxgb3
+
+cxgb3i-y := cxgb3i_init.o cxgb3i_iscsi.o cxgb3i_pdu.o cxgb3i_offload.o
+obj-$(CONFIG_SCSI_CXGB3_ISCSI) += cxgb3i_ddp.o cxgb3i.o
diff --git a/drivers/scsi/cxgb3i/Kconfig b/drivers/scsi/cxgb3i/Kconfig
new file mode 100644
index 0000000..2762814
--- /dev/null
+++ b/drivers/scsi/cxgb3i/Kconfig
@@ -0,0 +1,6 @@
+config SCSI_CXGB3_ISCSI
+	tristate "Chelsio S3xx iSCSI support"
+	select CHELSIO_T3
+	select SCSI_ISCSI_ATTRS
+	---help---
+	This driver supports iSCSI offload for the Chelsio S3 series devices.
diff --git a/drivers/scsi/cxgb3i/cxgb3i.h b/drivers/scsi/cxgb3i/cxgb3i.h
new file mode 100644
index 0000000..fde6e4c
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i.h
@@ -0,0 +1,139 @@
+/*
+ * cxgb3i.h: Chelsio S3xx iSCSI driver.
+ *
+ * Copyright (c) 2008 Chelsio Communications, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * Written by: Karen Xie (kxie@chelsio.com)
+ */
+
+#ifndef __CXGB3I_H__
+#define __CXGB3I_H__
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/errno.h>
+#include <linux/types.h>
+#include <linux/list.h>
+#include <linux/netdevice.h>
+#include <linux/scatterlist.h>
+#include <scsi/libiscsi_tcp.h>
+
+/* from cxgb3 LLD */
+#include "common.h"
+#include "t3_cpl.h"
+#include "t3cdev.h"
+#include "cxgb3_ctl_defs.h"
+#include "cxgb3_offload.h"
+#include "firmware_exports.h"
+
+#include "cxgb3i_offload.h"
+#include "cxgb3i_ddp.h"
+
+#define CXGB3I_SCSI_QDEPTH_DFLT	128
+#define CXGB3I_MAX_TARGET	CXGB3I_MAX_CONN
+#define CXGB3I_MAX_LUN		512
+#define ISCSI_PDU_NONPAYLOAD_MAX \
+	(sizeof(struct iscsi_hdr) + ISCSI_MAX_AHS_SIZE + 2*ISCSI_DIGEST_SIZE)
+
+struct cxgb3i_adapter;
+struct cxgb3i_hba;
+struct cxgb3i_endpoint;
+
+/**
+ * struct cxgb3i_hba - cxgb3i iscsi structure (per port)
+ *
+ * @snic:	cxgb3i adapter containing this port
+ * @ndev:	pointer to netdev structure
+ * @shost:	pointer to scsi host structure
+ */
+struct cxgb3i_hba {
+	struct cxgb3i_adapter *snic;
+	struct net_device *ndev;
+	struct Scsi_Host *shost;
+};
+
+/**
+ * struct cxgb3i_adapter - cxgb3i adapter structure (per pci)
+ *
+ * @listhead:	list head to link elements
+ * @lock:	lock for this structure
+ * @tdev:	pointer to t3cdev used by cxgb3 driver
+ * @pdev:	pointer to pci dev
+ * @hba_cnt:	# of hbas (the same as # of ports)
+ * @hba:	all the hbas on this adapter
+ * @tx_max_size: max. tx packet size supported
+ * @rx_max_size: max. rx packet size supported
+ * @tag_format: ddp tag format settings
+ */
+struct cxgb3i_adapter {
+	struct list_head list_head;
+	spinlock_t lock;
+	struct t3cdev *tdev;
+	struct pci_dev *pdev;
+	unsigned char hba_cnt;
+	struct cxgb3i_hba *hba[MAX_NPORTS];
+
+	unsigned int tx_max_size;
+	unsigned int rx_max_size;
+
+	struct cxgb3i_tag_format tag_format;
+};
+
+/**
+ * struct cxgb3i_conn - cxgb3i iscsi connection
+ *
+ * @listhead:	list head to link elements
+ * @cep:	pointer to iscsi_endpoint structure
+ * @conn:	pointer to iscsi_conn structure
+ * @hba:	pointer to the hba this conn. is going through
+ * @task_idx_bits: # of bits needed for session->cmds_max
+ */
+struct cxgb3i_conn {
+	struct list_head list_head;
+	struct cxgb3i_endpoint *cep;
+	struct iscsi_conn *conn;
+	struct cxgb3i_hba *hba;
+	unsigned int task_idx_bits;
+};
+
+/**
+ * struct cxgb3i_endpoint - iscsi tcp endpoint
+ *
+ * @c3cn:	the h/w tcp connection representation
+ * @hba:	pointer to the hba this conn. is going through
+ * @cconn:	pointer to the associated cxgb3i iscsi connection
+ */
+struct cxgb3i_endpoint {
+	struct s3_conn *c3cn;
+	struct cxgb3i_hba *hba;
+	struct cxgb3i_conn *cconn;
+};
+
+int cxgb3i_iscsi_init(void);
+void cxgb3i_iscsi_cleanup(void);
+
+struct cxgb3i_adapter *cxgb3i_adapter_add(struct t3cdev *);
+void cxgb3i_adapter_remove(struct t3cdev *);
+int cxgb3i_adapter_ulp_init(struct cxgb3i_adapter *);
+void cxgb3i_adapter_ulp_cleanup(struct cxgb3i_adapter *);
+
+struct cxgb3i_hba *cxgb3i_hba_find_by_netdev(struct net_device *);
+struct cxgb3i_hba *cxgb3i_hba_host_add(struct cxgb3i_adapter *,
+				       struct net_device *);
+void cxgb3i_hba_host_remove(struct cxgb3i_hba *);
+
+int cxgb3i_pdu_init(void);
+void cxgb3i_pdu_cleanup(void);
+void cxgb3i_conn_cleanup_task(struct iscsi_task *);
+int cxgb3i_conn_alloc_pdu(struct iscsi_task *, u8);
+int cxgb3i_conn_init_pdu(struct iscsi_task *, unsigned int, unsigned int);
+int cxgb3i_conn_xmit_pdu(struct iscsi_task *);
+
+void cxgb3i_release_itt(struct iscsi_task *task, itt_t hdr_itt);
+int cxgb3i_reserve_itt(struct iscsi_task *task, itt_t *hdr_itt);
+
+#endif
diff --git a/drivers/scsi/cxgb3i/cxgb3i_ddp.c b/drivers/scsi/cxgb3i/cxgb3i_ddp.c
new file mode 100644
index 0000000..1a41f04
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_ddp.c
@@ -0,0 +1,770 @@
+/*
+ * cxgb3i_ddp.c: Chelsio S3xx iSCSI DDP Manager.
+ *
+ * Copyright (c) 2008 Chelsio Communications, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * Written by: Karen Xie (kxie@chelsio.com)
+ */
+
+#include <linux/skbuff.h>
+
+/* from cxgb3 LLD */
+#include "common.h"
+#include "t3_cpl.h"
+#include "t3cdev.h"
+#include "cxgb3_ctl_defs.h"
+#include "cxgb3_offload.h"
+#include "firmware_exports.h"
+
+#include "cxgb3i_ddp.h"
+
+#define DRV_MODULE_NAME         "cxgb3i_ddp"
+#define DRV_MODULE_VERSION      "1.0.0"
+#define DRV_MODULE_RELDATE      "Dec. 1, 2008"
+
+static char version[] =
+	"Chelsio S3xx iSCSI DDP " DRV_MODULE_NAME
+	" v" DRV_MODULE_VERSION " (" DRV_MODULE_RELDATE ")\n";
+
+MODULE_AUTHOR("Karen Xie <kxie@chelsio.com>");
+MODULE_DESCRIPTION("cxgb3i ddp pagepod manager");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_MODULE_VERSION);
+
+#define ddp_log_error(fmt...) printk(KERN_ERR "cxgb3i_ddp: ERR! " fmt)
+#define ddp_log_warn(fmt...)  printk(KERN_WARNING "cxgb3i_ddp: WARN! " fmt)
+#define ddp_log_info(fmt...)  printk(KERN_INFO "cxgb3i_ddp: " fmt)
+
+#ifdef __DEBUG_CXGB3I_DDP__
+#define ddp_log_debug(fmt, args...) \
+	printk(KERN_INFO "cxgb3i_ddp: %s - " fmt, __func__ , ## args)
+#else
+#define ddp_log_debug(fmt...)
+#endif
+
+/*
+ * iSCSI Direct Data Placement
+ *
+ * T3 h/w can directly place the iSCSI Data-In or Data-Out PDU's payload into
+ * pre-posted final destination host-memory buffers based on the Initiator
+ * Task Tag (ITT) in Data-In or Target Task Tag (TTT) in Data-Out PDUs.
+ *
+ * The host memory address is programmed into h/w in the format of pagepod
+ * entries.
+ * The location of the pagepod entry is encoded into ddp tag which is used or
+ * is the base for ITT/TTT.
+ */
+
+#define DDP_PGIDX_MAX		4
+#define DDP_THRESHOLD	2048
+static unsigned char ddp_page_order[DDP_PGIDX_MAX] = {0, 1, 2, 4};
+static unsigned char ddp_page_shift[DDP_PGIDX_MAX] = {12, 13, 14, 16};
+static unsigned char page_idx = DDP_PGIDX_MAX;
+
+static LIST_HEAD(cxgb3i_ddp_list);
+static DEFINE_RWLOCK(cxgb3i_ddp_rwlock);
+
+/*
+ * functions to program the pagepod in h/w
+ */
+static inline void ulp_mem_io_set_hdr(struct sk_buff *skb, unsigned int addr)
+{
+	struct ulp_mem_io *req = (struct ulp_mem_io *)skb->head;
+
+	req->wr.wr_lo = 0;
+	req->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_BYPASS));
+	req->cmd_lock_addr = htonl(V_ULP_MEMIO_ADDR(addr >> 5) |
+				   V_ULPTX_CMD(ULP_MEM_WRITE));
+	req->len = htonl(V_ULP_MEMIO_DATA_LEN(PPOD_SIZE >> 5) |
+			 V_ULPTX_NFLITS((PPOD_SIZE >> 3) + 1));
+}
+
+static int set_ddp_map(struct cxgb3i_ddp_info *ddp, struct pagepod_hdr *hdr,
+		       unsigned int idx, unsigned int npods,
+		       struct cxgb3i_gather_list *gl)
+{
+	unsigned int pm_addr = (idx << PPOD_SIZE_SHIFT) + ddp->llimit;
+	int i;
+
+	for (i = 0; i < npods; i++, idx++, pm_addr += PPOD_SIZE) {
+		struct sk_buff *skb = ddp->gl_skb[idx];
+		struct pagepod *ppod;
+		int j, pidx;
+
+		/* hold on to the skb until we clear the ddp mapping */
+		skb_get(skb);
+
+		ulp_mem_io_set_hdr(skb, pm_addr);
+		ppod = (struct pagepod *)
+		       (skb->head + sizeof(struct ulp_mem_io));
+		memcpy(&(ppod->hdr), hdr, sizeof(struct pagepod));
+		for (pidx = 4 * i, j = 0; j < 5; ++j, ++pidx)
+			ppod->addr[j] = pidx < gl->nelem ?
+				     cpu_to_be64(gl->phys_addr[pidx]) : 0UL;
+
+		skb->priority = CPL_PRIORITY_CONTROL;
+		cxgb3_ofld_send(ddp->tdev, skb);
+	}
+	return 0;
+}
+
+static int clear_ddp_map(struct cxgb3i_ddp_info *ddp, unsigned int idx,
+			 unsigned int npods)
+{
+	unsigned int pm_addr = (idx << PPOD_SIZE_SHIFT) + ddp->llimit;
+	int i;
+
+	for (i = 0; i < npods; i++, idx++, pm_addr += PPOD_SIZE) {
+		struct sk_buff *skb = ddp->gl_skb[idx];
+
+		ddp->gl_skb[idx] = NULL;
+		memset((skb->head + sizeof(struct ulp_mem_io)), 0, PPOD_SIZE);
+		ulp_mem_io_set_hdr(skb, pm_addr);
+		skb->priority = CPL_PRIORITY_CONTROL;
+		cxgb3_ofld_send(ddp->tdev, skb);
+	}
+	return 0;
+}
+
+static inline int ddp_find_unused_entries(struct cxgb3i_ddp_info *ddp,
+					  int start, int max, int count,
+					  struct cxgb3i_gather_list *gl)
+{
+	unsigned int i, j;
+
+	spin_lock(&ddp->map_lock);
+	for (i = start; i <= max;) {
+		for (j = 0; j < count; j++) {
+			if (ddp->gl_map[i + j])
+				break;
+		}
+		if (j == count) {
+			for (j = 0; j < count; j++)
+				ddp->gl_map[i + j] = gl;
+			spin_unlock(&ddp->map_lock);
+			return i;
+		}
+		i += j + 1;
+	}
+	spin_unlock(&ddp->map_lock);
+	return -EBUSY;
+}
+
+static inline void ddp_unmark_entries(struct cxgb3i_ddp_info *ddp,
+				      int start, int count)
+{
+	spin_lock(&ddp->map_lock);
+	memset(&ddp->gl_map[start], 0,
+	       count * sizeof(struct cxgb3i_gather_list *));
+	spin_unlock(&ddp->map_lock);
+}
+
+static inline void ddp_free_gl_skb(struct cxgb3i_ddp_info *ddp,
+				   int idx, int count)
+{
+	int i;
+
+	for (i = 0; i < count; i++, idx++)
+		if (ddp->gl_skb[idx]) {
+			kfree_skb(ddp->gl_skb[idx]);
+			ddp->gl_skb[idx] = NULL;
+		}
+}
+
+static inline int ddp_alloc_gl_skb(struct cxgb3i_ddp_info *ddp, int idx,
+				   int count, gfp_t gfp)
+{
+	int i;
+
+	for (i = 0; i < count; i++) {
+		struct sk_buff *skb = alloc_skb(sizeof(struct ulp_mem_io) +
+						PPOD_SIZE, gfp);
+		if (skb) {
+			ddp->gl_skb[idx + i] = skb;
+			skb_put(skb, sizeof(struct ulp_mem_io) + PPOD_SIZE);
+		} else {
+			ddp_free_gl_skb(ddp, idx, i);
+			return -ENOMEM;
+		}
+	}
+	return 0;
+}
+
+/**
+ * cxgb3i_ddp_find_page_index - return ddp page index for a given page size.
+ * @pgsz: page size
+ * return the ddp page index, if no match is found return DDP_PGIDX_MAX.
+ */
+int cxgb3i_ddp_find_page_index(unsigned long pgsz)
+{
+	int i;
+
+	for (i = 0; i < DDP_PGIDX_MAX; i++) {
+		if (pgsz == (1UL << ddp_page_shift[i]))
+			return i;
+	}
+	ddp_log_debug("ddp page size 0x%lx not supported.\n", pgsz);
+	return DDP_PGIDX_MAX;
+}
+EXPORT_SYMBOL_GPL(cxgb3i_ddp_find_page_index);
+
+static inline void ddp_gl_unmap(struct pci_dev *pdev,
+				struct cxgb3i_gather_list *gl)
+{
+	int i;
+
+	for (i = 0; i < gl->nelem; i++)
+		pci_unmap_page(pdev, gl->phys_addr[i], PAGE_SIZE,
+			       PCI_DMA_FROMDEVICE);
+}
+
+static inline int ddp_gl_map(struct pci_dev *pdev,
+			     struct cxgb3i_gather_list *gl)
+{
+	int i;
+
+	for (i = 0; i < gl->nelem; i++) {
+		gl->phys_addr[i] = pci_map_page(pdev, gl->pages[i], 0,
+						PAGE_SIZE,
+						PCI_DMA_FROMDEVICE);
+		if (unlikely(pci_dma_mapping_error(pdev, gl->phys_addr[i])))
+			goto unmap;
+	}
+
+	return i;
+
+unmap:
+	if (i) {
+		unsigned int nelem = gl->nelem;
+
+		gl->nelem = i;
+		ddp_gl_unmap(pdev, gl);
+		gl->nelem = nelem;
+	}
+	return -ENOMEM;
+}
+
+/**
+ * cxgb3i_ddp_make_gl - build ddp page buffer list
+ * @xferlen: total buffer length
+ * @sgl: page buffer scatter-gather list
+ * @sgcnt: # of page buffers
+ * @pdev: pci_dev, used for pci map
+ * @gfp: allocation mode
+ *
+ * construct a ddp page buffer list from the scsi scattergather list.
+ * coalesce buffers as much as possible, and obtain dma addresses for
+ * each page.
+ *
+ * Return the cxgb3i_gather_list constructed from the page buffers if the
+ * memory can be used for ddp. Return NULL otherwise.
+ */
+struct cxgb3i_gather_list *cxgb3i_ddp_make_gl(unsigned int xferlen,
+					      struct scatterlist *sgl,
+					      unsigned int sgcnt,
+					      struct pci_dev *pdev,
+					      gfp_t gfp)
+{
+	struct cxgb3i_gather_list *gl;
+	struct scatterlist *sg = sgl;
+	struct page *sgpage = sg_page(sg);
+	unsigned int sglen = sg->length;
+	unsigned int sgoffset = sg->offset;
+	unsigned int npages = (xferlen + sgoffset + PAGE_SIZE - 1) >>
+			      PAGE_SHIFT;
+	int i = 1, j = 0;
+
+	if (xferlen < DDP_THRESHOLD) {
+		ddp_log_debug("xfer %u < threshold %u, no ddp.\n",
+			      xferlen, DDP_THRESHOLD);
+		return NULL;
+	}
+
+	gl = kzalloc(sizeof(struct cxgb3i_gather_list) +
+		     npages * (sizeof(dma_addr_t) + sizeof(struct page *)),
+		     gfp);
+	if (!gl)
+		return NULL;
+
+	gl->pages = (struct page **)&gl->phys_addr[npages];
+	gl->length = xferlen;
+	gl->offset = sgoffset;
+	gl->pages[0] = sgpage;
+
+	sg = sg_next(sg);
+	while (sg) {
+		struct page *page = sg_page(sg);
+
+		if (sgpage == page && sg->offset == sgoffset + sglen)
+			sglen += sg->length;
+		else {
+			/* make sure the sgl is fit for ddp:
+			 * each has the same page size, and
+			 * all of the middle pages are used completely
+			 */
+			if ((j && sgoffset) ||
+			    ((i != sgcnt - 1) &&
+			     ((sglen + sgoffset) & ~PAGE_MASK)))
+				goto error_out;
+
+			j++;
+			if (j == gl->nelem || sg->offset)
+				goto error_out;
+			gl->pages[j] = page;
+			sglen = sg->length;
+			sgoffset = sg->offset;
+			sgpage = page;
+		}
+		i++;
+		sg = sg_next(sg);
+	}
+	gl->nelem = ++j;
+
+	if (ddp_gl_map(pdev, gl) < 0)
+		goto error_out;
+
+	return gl;
+
+error_out:
+	kfree(gl);
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(cxgb3i_ddp_make_gl);
+
+/**
+ * cxgb3i_ddp_release_gl - release a page buffer list
+ * @gl: a ddp page buffer list
+ * @pdev: pci_dev used for pci_unmap
+ * free a ddp page buffer list resulted from cxgb3i_ddp_make_gl().
+ */
+void cxgb3i_ddp_release_gl(struct cxgb3i_gather_list *gl,
+			   struct pci_dev *pdev)
+{
+	ddp_gl_unmap(pdev, gl);
+	kfree(gl);
+}
+EXPORT_SYMBOL_GPL(cxgb3i_ddp_release_gl);
+
+/**
+ * cxgb3i_ddp_tag_reserve - set up ddp for a data transfer
+ * @tdev: t3cdev adapter
+ * @tid: connection id
+ * @tformat: tag format
+ * @tagp: the s/w tag, if ddp setup is successful, it will be updated with
+ *	  ddp/hw tag
+ * @gl: the page momory list
+ * @gfp: allocation mode
+ *
+ * ddp setup for a given page buffer list and construct the ddp tag.
+ * return 0 if success, < 0 otherwise.
+ */
+int cxgb3i_ddp_tag_reserve(struct t3cdev *tdev, unsigned int tid,
+			   struct cxgb3i_tag_format *tformat, u32 *tagp,
+			   struct cxgb3i_gather_list *gl, gfp_t gfp)
+{
+	struct cxgb3i_ddp_info *ddp = tdev->ulp_iscsi;
+	struct pagepod_hdr hdr;
+	unsigned int npods;
+	int idx = -1, idx_max;
+	int err = -ENOMEM;
+	u32 sw_tag = *tagp;
+	u32 tag;
+
+	if (page_idx >= DDP_PGIDX_MAX || !ddp || !gl || !gl->nelem ||
+		gl->length < DDP_THRESHOLD) {
+		ddp_log_debug("pgidx %u, xfer %u/%u, NO ddp.\n",
+			      page_idx, gl->length, DDP_THRESHOLD);
+		return -EINVAL;
+	}
+
+	npods = (gl->nelem + PPOD_PAGES_MAX - 1) >> PPOD_PAGES_SHIFT;
+	idx_max = ddp->nppods - npods + 1;
+
+	if (ddp->idx_last == ddp->nppods)
+		idx = ddp_find_unused_entries(ddp, 0, idx_max, npods, gl);
+	else {
+		idx = ddp_find_unused_entries(ddp, ddp->idx_last + 1,
+					      idx_max, npods, gl);
+		if (idx < 0 && ddp->idx_last >= npods)
+			idx = ddp_find_unused_entries(ddp, 0,
+						      ddp->idx_last - npods + 1,
+						      npods, gl);
+	}
+	if (idx < 0) {
+		ddp_log_debug("xferlen %u, gl %u, npods %u NO DDP.\n",
+			      gl->length, gl->nelem, npods);
+		return idx;
+	}
+
+	err = ddp_alloc_gl_skb(ddp, idx, npods, gfp);
+	if (err < 0)
+		goto unmark_entries;
+
+	tag = cxgb3i_ddp_tag_base(tformat, sw_tag);
+	tag |= idx << PPOD_IDX_SHIFT;
+
+	hdr.rsvd = 0;
+	hdr.vld_tid = htonl(F_PPOD_VALID | V_PPOD_TID(tid));
+	hdr.pgsz_tag_clr = htonl(tag & ddp->rsvd_tag_mask);
+	hdr.maxoffset = htonl(gl->length);
+	hdr.pgoffset = htonl(gl->offset);
+
+	err = set_ddp_map(ddp, &hdr, idx, npods, gl);
+	if (err < 0)
+		goto free_gl_skb;
+
+	ddp->idx_last = idx;
+	ddp_log_debug("xfer %u, gl %u,%u, tid 0x%x, 0x%x -> 0x%x(%u,%u).\n",
+		      gl->length, gl->nelem, gl->offset, tid, sw_tag, tag,
+		      idx, npods);
+	*tagp = tag;
+	return 0;
+
+free_gl_skb:
+	ddp_free_gl_skb(ddp, idx, npods);
+unmark_entries:
+	ddp_unmark_entries(ddp, idx, npods);
+	return err;
+}
+EXPORT_SYMBOL_GPL(cxgb3i_ddp_tag_reserve);
+
+/**
+ * cxgb3i_ddp_tag_release - release a ddp tag
+ * @tdev: t3cdev adapter
+ * @tag: ddp tag
+ * ddp cleanup for a given ddp tag and release all the resources held
+ */
+void cxgb3i_ddp_tag_release(struct t3cdev *tdev, u32 tag)
+{
+	struct cxgb3i_ddp_info *ddp = tdev->ulp_iscsi;
+	u32 idx;
+
+	if (!ddp) {
+		ddp_log_error("release ddp tag 0x%x, ddp NULL.\n", tag);
+		return;
+	}
+
+	idx = (tag >> PPOD_IDX_SHIFT) & ddp->idx_mask;
+	if (idx < ddp->nppods) {
+		struct cxgb3i_gather_list *gl = ddp->gl_map[idx];
+		unsigned int npods;
+
+		if (!gl) {
+			ddp_log_error("release ddp 0x%x, idx 0x%x, gl NULL.\n",
+				      tag, idx);
+			return;
+		}
+		npods = (gl->nelem + PPOD_PAGES_MAX - 1) >> PPOD_PAGES_SHIFT;
+		ddp_log_debug("ddp tag 0x%x, release idx 0x%x, npods %u.\n",
+			      tag, idx, npods);
+		clear_ddp_map(ddp, idx, npods);
+		ddp_unmark_entries(ddp, idx, npods);
+		cxgb3i_ddp_release_gl(gl, ddp->pdev);
+	} else
+		ddp_log_error("ddp tag 0x%x, idx 0x%x > max 0x%x.\n",
+			      tag, idx, ddp->nppods);
+}
+EXPORT_SYMBOL_GPL(cxgb3i_ddp_tag_release);
+
+static int setup_conn_pgidx(struct t3cdev *tdev, unsigned int tid, int pg_idx,
+			    int reply)
+{
+	struct sk_buff *skb = alloc_skb(sizeof(struct cpl_set_tcb_field),
+					GFP_KERNEL);
+	struct cpl_set_tcb_field *req;
+	u64 val = pg_idx < DDP_PGIDX_MAX ? pg_idx : 0;
+
+	if (!skb)
+		return -ENOMEM;
+
+	/* set up ulp submode and page size */
+	req = (struct cpl_set_tcb_field *)skb_put(skb, sizeof(*req));
+	req->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_FORWARD));
+	OPCODE_TID(req) = htonl(MK_OPCODE_TID(CPL_SET_TCB_FIELD, tid));
+	req->reply = V_NO_REPLY(reply ? 0 : 1);
+	req->cpu_idx = 0;
+	req->word = htons(31);
+	req->mask = cpu_to_be64(0xF0000000);
+	req->val = cpu_to_be64(val << 28);
+	skb->priority = CPL_PRIORITY_CONTROL;
+
+	cxgb3_ofld_send(tdev, skb);
+	return 0;
+}
+
+/**
+ * cxgb3i_setup_conn_host_pagesize - setup the conn.'s ddp page size
+ * @tdev: t3cdev adapter
+ * @tid: connection id
+ * @reply: request reply from h/w
+ * set up the ddp page size based on the host PAGE_SIZE for a connection
+ * identified by tid
+ */
+int cxgb3i_setup_conn_host_pagesize(struct t3cdev *tdev, unsigned int tid,
+				    int reply)
+{
+	return setup_conn_pgidx(tdev, tid, page_idx, reply);
+}
+EXPORT_SYMBOL_GPL(cxgb3i_setup_conn_host_pagesize);
+
+/**
+ * cxgb3i_setup_conn_pagesize - setup the conn.'s ddp page size
+ * @tdev: t3cdev adapter
+ * @tid: connection id
+ * @reply: request reply from h/w
+ * @pgsz: ddp page size
+ * set up the ddp page size for a connection identified by tid
+ */
+int cxgb3i_setup_conn_pagesize(struct t3cdev *tdev, unsigned int tid,
+				int reply, unsigned long pgsz)
+{
+	int pgidx = cxgb3i_ddp_find_page_index(pgsz);
+
+	return setup_conn_pgidx(tdev, tid, pgidx, reply);
+}
+EXPORT_SYMBOL_GPL(cxgb3i_setup_conn_pagesize);
+
+/**
+ * cxgb3i_setup_conn_digest - setup conn. digest setting
+ * @tdev: t3cdev adapter
+ * @tid: connection id
+ * @hcrc: header digest enabled
+ * @dcrc: data digest enabled
+ * @reply: request reply from h/w
+ * set up the iscsi digest settings for a connection identified by tid
+ */
+int cxgb3i_setup_conn_digest(struct t3cdev *tdev, unsigned int tid,
+			     int hcrc, int dcrc, int reply)
+{
+	struct sk_buff *skb = alloc_skb(sizeof(struct cpl_set_tcb_field),
+					GFP_KERNEL);
+	struct cpl_set_tcb_field *req;
+	u64 val = (hcrc ? 1 : 0) | (dcrc ? 2 : 0);
+
+	if (!skb)
+		return -ENOMEM;
+
+	/* set up ulp submode and page size */
+	req = (struct cpl_set_tcb_field *)skb_put(skb, sizeof(*req));
+	req->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_FORWARD));
+	OPCODE_TID(req) = htonl(MK_OPCODE_TID(CPL_SET_TCB_FIELD, tid));
+	req->reply = V_NO_REPLY(reply ? 0 : 1);
+	req->cpu_idx = 0;
+	req->word = htons(31);
+	req->mask = cpu_to_be64(0x0F000000);
+	req->val = cpu_to_be64(val << 24);
+	skb->priority = CPL_PRIORITY_CONTROL;
+
+	cxgb3_ofld_send(tdev, skb);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(cxgb3i_setup_conn_digest);
+
+static int ddp_init(struct t3cdev *tdev)
+{
+	struct cxgb3i_ddp_info *ddp;
+	struct ulp_iscsi_info uinfo;
+	unsigned int ppmax, bits;
+	int i, err;
+	static int vers_printed;
+
+	if (!vers_printed) {
+		printk(KERN_INFO "%s", version);
+		vers_printed = 1;
+	}
+
+	err = tdev->ctl(tdev, ULP_ISCSI_GET_PARAMS, &uinfo);
+	if (err < 0) {
+		ddp_log_error("%s, failed to get iscsi param err=%d.\n",
+				 tdev->name, err);
+		return err;
+	}
+
+	ppmax = (uinfo.ulimit - uinfo.llimit + 1) >> PPOD_SIZE_SHIFT;
+	bits = __ilog2_u32(ppmax) + 1;
+	if (bits > PPOD_IDX_MAX_SIZE)
+		bits = PPOD_IDX_MAX_SIZE;
+	ppmax = (1 << (bits - 1)) - 1;
+
+	ddp = cxgb3i_alloc_big_mem(sizeof(struct cxgb3i_ddp_info) +
+				   ppmax *
+					(sizeof(struct cxgb3i_gather_list *) +
+					sizeof(struct sk_buff *)),
+				   GFP_KERNEL);
+	if (!ddp) {
+		ddp_log_warn("%s unable to alloc ddp 0x%d, ddp disabled.\n",
+			     tdev->name, ppmax);
+		return 0;
+	}
+	ddp->gl_map = (struct cxgb3i_gather_list **)(ddp + 1);
+	ddp->gl_skb = (struct sk_buff **)(((char *)ddp->gl_map) +
+					  ppmax *
+					  sizeof(struct cxgb3i_gather_list *));
+	spin_lock_init(&ddp->map_lock);
+
+	ddp->tdev = tdev;
+	ddp->pdev = uinfo.pdev;
+	ddp->max_txsz = min_t(unsigned int, uinfo.max_txsz, ULP2_MAX_PKT_SIZE);
+	ddp->max_rxsz = min_t(unsigned int, uinfo.max_rxsz, ULP2_MAX_PKT_SIZE);
+	ddp->llimit = uinfo.llimit;
+	ddp->ulimit = uinfo.ulimit;
+	ddp->nppods = ppmax;
+	ddp->idx_last = ppmax;
+	ddp->idx_bits = bits;
+	ddp->idx_mask = (1 << bits) - 1;
+	ddp->rsvd_tag_mask = (1 << (bits + PPOD_IDX_SHIFT)) - 1;
+
+	uinfo.tagmask = ddp->idx_mask << PPOD_IDX_SHIFT;
+	for (i = 0; i < DDP_PGIDX_MAX; i++)
+		uinfo.pgsz_factor[i] = ddp_page_order[i];
+	uinfo.ulimit = uinfo.llimit + (ppmax << PPOD_SIZE_SHIFT);
+
+	err = tdev->ctl(tdev, ULP_ISCSI_SET_PARAMS, &uinfo);
+	if (err < 0) {
+		ddp_log_warn("%s unable to set iscsi param err=%d, "
+			      "ddp disabled.\n", tdev->name, err);
+		goto free_ddp_map;
+	}
+
+	tdev->ulp_iscsi = ddp;
+
+	/* add to the list */
+	write_lock(&cxgb3i_ddp_rwlock);
+	list_add_tail(&ddp->list, &cxgb3i_ddp_list);
+	write_unlock(&cxgb3i_ddp_rwlock);
+
+	ddp_log_info("nppods %u (0x%x ~ 0x%x), bits %u, mask 0x%x,0x%x "
+			"pkt %u,%u.\n",
+			ppmax, ddp->llimit, ddp->ulimit, ddp->idx_bits,
+			ddp->idx_mask, ddp->rsvd_tag_mask,
+			ddp->max_txsz, ddp->max_rxsz);
+	return 0;
+
+free_ddp_map:
+	cxgb3i_free_big_mem(ddp);
+	return err;
+}
+
+/**
+ * cxgb3i_adapter_ddp_init - initialize the adapter's ddp resource
+ * @tdev: t3cdev adapter
+ * @tformat: tag format
+ * @txsz: max tx pkt size, filled in by this func.
+ * @rxsz: max rx pkt size, filled in by this func.
+ * initialize the ddp pagepod manager for a given adapter if needed and
+ * setup the tag format for a given iscsi entity
+ */
+int cxgb3i_adapter_ddp_init(struct t3cdev *tdev,
+			    struct cxgb3i_tag_format *tformat,
+			    unsigned int *txsz, unsigned int *rxsz)
+{
+	struct cxgb3i_ddp_info *ddp;
+	unsigned char idx_bits;
+
+	if (!tformat)
+		return -EINVAL;
+
+	if (!tdev->ulp_iscsi) {
+		int err = ddp_init(tdev);
+		if (err < 0)
+			return err;
+	}
+	ddp = (struct cxgb3i_ddp_info *)tdev->ulp_iscsi;
+
+	idx_bits = 32 - tformat->sw_bits;
+	tformat->rsvd_bits = ddp->idx_bits;
+	tformat->rsvd_shift = PPOD_IDX_SHIFT;
+	tformat->rsvd_mask = (1 << tformat->rsvd_bits) - 1;
+
+	ddp_log_info("tag format: sw %u, rsvd %u,%u, mask 0x%x.\n",
+		      tformat->sw_bits, tformat->rsvd_bits,
+		      tformat->rsvd_shift, tformat->rsvd_mask);
+
+	*txsz = ddp->max_txsz;
+	*rxsz = ddp->max_rxsz;
+	ddp_log_info("ddp max pkt size: %u, %u.\n",
+		     ddp->max_txsz, ddp->max_rxsz);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(cxgb3i_adapter_ddp_init);
+
+static void ddp_release(struct cxgb3i_ddp_info *ddp)
+{
+	int i = 0;
+	struct t3cdev *tdev = ddp->tdev;
+
+	tdev->ulp_iscsi = NULL;
+	while (i < ddp->nppods) {
+		struct cxgb3i_gather_list *gl = ddp->gl_map[i];
+		if (gl) {
+			int npods = (gl->nelem + PPOD_PAGES_MAX - 1)
+				     >> PPOD_PAGES_SHIFT;
+
+			kfree(gl);
+			ddp_free_gl_skb(ddp, i, npods);
+		} else
+			i++;
+	}
+	cxgb3i_free_big_mem(ddp);
+}
+
+/**
+ * cxgb3i_adapter_ddp_cleanup - release the adapter's ddp resource
+ * @tdev: t3cdev adapter
+ * release all the resource held by the ddp pagepod manager for a given
+ * adapter if needed
+ */
+void cxgb3i_adapter_ddp_cleanup(struct t3cdev *tdev)
+{
+	struct cxgb3i_ddp_info *ddp;
+
+	/* remove from the list */
+	write_lock(&cxgb3i_ddp_rwlock);
+	list_for_each_entry(ddp, &cxgb3i_ddp_list, list) {
+		if (ddp->tdev == tdev) {
+			list_del(&ddp->list);
+			break;
+		}
+	}
+	write_unlock(&cxgb3i_ddp_rwlock);
+
+	if (ddp)
+		ddp_release(ddp);
+}
+EXPORT_SYMBOL_GPL(cxgb3i_adapter_ddp_cleanup);
+
+/**
+ * cxgb3i_ddp_init_module - module init entry point
+ * initialize any driver wide global data structures
+ */
+static int __init cxgb3i_ddp_init_module(void)
+{
+	page_idx = cxgb3i_ddp_find_page_index(PAGE_SIZE);
+	ddp_log_info("system PAGE_SIZE %lu, ddp idx %u.\n",
+		     PAGE_SIZE, page_idx);
+	return 0;
+}
+
+/**
+ * cxgb3i_ddp_exit_module - module cleanup/exit entry point
+ * go through the ddp list and release any resource held.
+ */
+static void __exit cxgb3i_ddp_exit_module(void)
+{
+	struct cxgb3i_ddp_info *ddp;
+
+	/* release all ddp manager if there is any */
+	write_lock(&cxgb3i_ddp_rwlock);
+	list_for_each_entry(ddp, &cxgb3i_ddp_list, list) {
+		list_del(&ddp->list);
+		ddp_release(ddp);
+	}
+	write_unlock(&cxgb3i_ddp_rwlock);
+}
+
+module_init(cxgb3i_ddp_init_module);
+module_exit(cxgb3i_ddp_exit_module);
diff --git a/drivers/scsi/cxgb3i/cxgb3i_ddp.h b/drivers/scsi/cxgb3i/cxgb3i_ddp.h
new file mode 100644
index 0000000..5c7c4d9
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_ddp.h
@@ -0,0 +1,306 @@
+/*
+ * cxgb3i_ddp.h: Chelsio S3xx iSCSI DDP Manager.
+ *
+ * Copyright (c) 2008 Chelsio Communications, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * Written by: Karen Xie (kxie@chelsio.com)
+ */
+
+#ifndef __CXGB3I_ULP2_DDP_H__
+#define __CXGB3I_ULP2_DDP_H__
+
+/**
+ * struct cxgb3i_tag_format - cxgb3i ulp tag format for an iscsi entity
+ *
+ * @sw_bits:	# of bits used by iscsi software layer
+ * @rsvd_bits:	# of bits used by h/w
+ * @rsvd_shift:	h/w bits shift left
+ * @rsvd_mask:	reserved bit mask
+ */
+struct cxgb3i_tag_format {
+	unsigned char sw_bits;
+	unsigned char rsvd_bits;
+	unsigned char rsvd_shift;
+	unsigned char filler[1];
+	u32 rsvd_mask;
+};
+
+/**
+ * struct cxgb3i_gather_list - cxgb3i direct data placement memory
+ *
+ * @tag:	ddp tag
+ * @length:	total data buffer length
+ * @offset:	initial offset to the 1st page
+ * @nelem:	# of pages
+ * @pages:	page pointers
+ * @phys_addr:	physical address
+ */
+struct cxgb3i_gather_list {
+	u32 tag;
+	unsigned int length;
+	unsigned int offset;
+	unsigned int nelem;
+	struct page **pages;
+	dma_addr_t phys_addr[0];
+};
+
+/**
+ * struct cxgb3i_ddp_info - cxgb3i direct data placement for pdu payload
+ *
+ * @list:	list head to link elements
+ * @tdev:	pointer to t3cdev used by cxgb3 driver
+ * @max_txsz:	max tx packet size for ddp
+ * @max_rxsz:	max rx packet size for ddp
+ * @llimit:	lower bound of the page pod memory
+ * @ulimit:	upper bound of the page pod memory
+ * @nppods:	# of page pod entries
+ * @idx_last:	page pod entry last used
+ * @idx_bits:	# of bits the pagepod index would take
+ * @idx_mask:	pagepod index mask
+ * @rsvd_tag_mask: tag mask
+ * @map_lock:	lock to synchonize access to the page pod map
+ * @gl_map:	ddp memory gather list
+ * @gl_skb:	skb used to program the pagepod
+ */
+struct cxgb3i_ddp_info {
+	struct list_head list;
+	struct t3cdev *tdev;
+	struct pci_dev *pdev;
+	unsigned int max_txsz;
+	unsigned int max_rxsz;
+	unsigned int llimit;
+	unsigned int ulimit;
+	unsigned int nppods;
+	unsigned int idx_last;
+	unsigned char idx_bits;
+	unsigned char filler[3];
+	u32 idx_mask;
+	u32 rsvd_tag_mask;
+	spinlock_t map_lock;
+	struct cxgb3i_gather_list **gl_map;
+	struct sk_buff **gl_skb;
+};
+
+#define ULP2_MAX_PKT_SIZE	16224
+#define ULP2_MAX_PDU_PAYLOAD	(ULP2_MAX_PKT_SIZE - ISCSI_PDU_NONPAYLOAD_MAX)
+#define PPOD_PAGES_MAX		4
+#define PPOD_PAGES_SHIFT	2	/* 4 pages per pod */
+
+/*
+ * struct pagepod_hdr, pagepod - pagepod format
+ */
+struct pagepod_hdr {
+	u32 vld_tid;
+	u32 pgsz_tag_clr;
+	u32 maxoffset;
+	u32 pgoffset;
+	u64 rsvd;
+};
+
+struct pagepod {
+	struct pagepod_hdr hdr;
+	u64 addr[PPOD_PAGES_MAX + 1];
+};
+
+#define PPOD_SIZE		sizeof(struct pagepod)	/* 64 */
+#define PPOD_SIZE_SHIFT		6
+
+#define PPOD_COLOR_SHIFT	0
+#define PPOD_COLOR_SIZE		6
+#define PPOD_COLOR_MASK		((1 << PPOD_COLOR_SIZE) - 1)
+
+#define PPOD_IDX_SHIFT		PPOD_COLOR_SIZE
+#define PPOD_IDX_MAX_SIZE	24
+
+#define S_PPOD_TID    0
+#define M_PPOD_TID    0xFFFFFF
+#define V_PPOD_TID(x) ((x) << S_PPOD_TID)
+
+#define S_PPOD_VALID    24
+#define V_PPOD_VALID(x) ((x) << S_PPOD_VALID)
+#define F_PPOD_VALID    V_PPOD_VALID(1U)
+
+#define S_PPOD_COLOR    0
+#define M_PPOD_COLOR    0x3F
+#define V_PPOD_COLOR(x) ((x) << S_PPOD_COLOR)
+
+#define S_PPOD_TAG    6
+#define M_PPOD_TAG    0xFFFFFF
+#define V_PPOD_TAG(x) ((x) << S_PPOD_TAG)
+
+#define S_PPOD_PGSZ    30
+#define M_PPOD_PGSZ    0x3
+#define V_PPOD_PGSZ(x) ((x) << S_PPOD_PGSZ)
+
+/*
+ * large memory chunk allocation/release
+ * use vmalloc() if kmalloc() fails
+ */
+static inline void *cxgb3i_alloc_big_mem(unsigned int size,
+					 gfp_t gfp)
+{
+	void *p = kmalloc(size, gfp);
+	if (!p)
+		p = vmalloc(size);
+	if (p)
+		memset(p, 0, size);
+	return p;
+}
+
+static inline void cxgb3i_free_big_mem(void *addr)
+{
+	if (is_vmalloc_addr(addr))
+		vfree(addr);
+	else
+		kfree(addr);
+}
+
+/*
+ * cxgb3i ddp tag are 32 bits, it consists of reserved bits used by h/w and
+ * non-reserved bits that can be used by the iscsi s/w.
+ * The reserved bits are identified by the rsvd_bits and rsvd_shift fields
+ * in struct cxgb3i_tag_format.
+ *
+ * The upper most reserved bit can be used to check if a tag is ddp tag or not:
+ * 	if the bit is 0, the tag is a valid ddp tag
+ */
+
+/**
+ * cxgb3i_is_ddp_tag - check if a given tag is a hw/ddp tag
+ * @tformat: tag format information
+ * @tag: tag to be checked
+ *
+ * return true if the tag is a ddp tag, false otherwise.
+ */
+static inline int cxgb3i_is_ddp_tag(struct cxgb3i_tag_format *tformat, u32 tag)
+{
+	return !(tag & (1 << (tformat->rsvd_bits + tformat->rsvd_shift - 1)));
+}
+
+/**
+ * cxgb3i_sw_tag_usable - check if a given s/w tag has enough bits left for
+ *			  the reserved/hw bits
+ * @tformat: tag format information
+ * @sw_tag: s/w tag to be checked
+ *
+ * return true if the tag is a ddp tag, false otherwise.
+ */
+static inline int cxgb3i_sw_tag_usable(struct cxgb3i_tag_format *tformat,
+					u32 sw_tag)
+{
+	sw_tag >>= (32 - tformat->rsvd_bits);
+	return !sw_tag;
+}
+
+/**
+ * cxgb3i_set_non_ddp_tag - mark a given s/w tag as an invalid ddp tag
+ * @tformat: tag format information
+ * @sw_tag: s/w tag to be checked
+ *
+ * insert 1 at the upper most reserved bit to mark it as an invalid ddp tag.
+ */
+static inline u32 cxgb3i_set_non_ddp_tag(struct cxgb3i_tag_format *tformat,
+					 u32 sw_tag)
+{
+	unsigned char shift = tformat->rsvd_bits + tformat->rsvd_shift - 1;
+	u32 mask = (1 << shift) - 1;
+
+	if (sw_tag && (sw_tag & ~mask)) {
+		u32 v1 = sw_tag & ((1 << shift) - 1);
+		u32 v2 = (sw_tag >> (shift - 1)) << shift;
+
+		return v2 | v1 | 1 << shift;
+	}
+	return sw_tag | 1 << shift;
+}
+
+/**
+ * cxgb3i_ddp_tag_base - shift the s/w tag bits so that reserved bits are not
+ *			 used.
+ * @tformat: tag format information
+ * @sw_tag: s/w tag to be checked
+ */
+static inline u32 cxgb3i_ddp_tag_base(struct cxgb3i_tag_format *tformat,
+				      u32 sw_tag)
+{
+	u32 mask = (1 << tformat->rsvd_shift) - 1;
+
+	if (sw_tag && (sw_tag & ~mask)) {
+		u32 v1 = sw_tag & mask;
+		u32 v2 = sw_tag >> tformat->rsvd_shift;
+
+		v2 <<= tformat->rsvd_shift + tformat->rsvd_bits;
+		return v2 | v1;
+	}
+	return sw_tag;
+}
+
+/**
+ * cxgb3i_tag_rsvd_bits - get the reserved bits used by the h/w
+ * @tformat: tag format information
+ * @tag: tag to be checked
+ *
+ * return the reserved bits in the tag
+ */
+static inline u32 cxgb3i_tag_rsvd_bits(struct cxgb3i_tag_format *tformat,
+				       u32 tag)
+{
+	if (cxgb3i_is_ddp_tag(tformat, tag))
+		return (tag >> tformat->rsvd_shift) & tformat->rsvd_mask;
+	return 0;
+}
+
+/**
+ * cxgb3i_tag_nonrsvd_bits - get the non-reserved bits used by the s/w
+ * @tformat: tag format information
+ * @tag: tag to be checked
+ *
+ * return the non-reserved bits in the tag.
+ */
+static inline u32 cxgb3i_tag_nonrsvd_bits(struct cxgb3i_tag_format *tformat,
+					  u32 tag)
+{
+	unsigned char shift = tformat->rsvd_bits + tformat->rsvd_shift - 1;
+	u32 v1, v2;
+
+	if (cxgb3i_is_ddp_tag(tformat, tag)) {
+		v1 = tag & ((1 << tformat->rsvd_shift) - 1);
+		v2 = (tag >> (shift + 1)) << tformat->rsvd_shift;
+	} else {
+		u32 mask = (1 << shift) - 1;
+
+		tag &= ~(1 << shift);
+		v1 = tag & mask;
+		v2 = (tag >> 1) & ~mask;
+	}
+	return v1 | v2;
+}
+
+int cxgb3i_ddp_tag_reserve(struct t3cdev *, unsigned int tid,
+			   struct cxgb3i_tag_format *, u32 *tag,
+			   struct cxgb3i_gather_list *, gfp_t gfp);
+void cxgb3i_ddp_tag_release(struct t3cdev *, u32 tag);
+
+struct cxgb3i_gather_list *cxgb3i_ddp_make_gl(unsigned int xferlen,
+				struct scatterlist *sgl,
+				unsigned int sgcnt,
+				struct pci_dev *pdev,
+				gfp_t gfp);
+void cxgb3i_ddp_release_gl(struct cxgb3i_gather_list *gl,
+				struct pci_dev *pdev);
+
+int cxgb3i_setup_conn_host_pagesize(struct t3cdev *, unsigned int tid,
+				    int reply);
+int cxgb3i_setup_conn_pagesize(struct t3cdev *, unsigned int tid, int reply,
+			       unsigned long pgsz);
+int cxgb3i_setup_conn_digest(struct t3cdev *, unsigned int tid,
+				int hcrc, int dcrc, int reply);
+int cxgb3i_ddp_find_page_index(unsigned long pgsz);
+int cxgb3i_adapter_ddp_init(struct t3cdev *, struct cxgb3i_tag_format *,
+			    unsigned int *txsz, unsigned int *rxsz);
+void cxgb3i_adapter_ddp_cleanup(struct t3cdev *);
+#endif
diff --git a/drivers/scsi/cxgb3i/cxgb3i_init.c b/drivers/scsi/cxgb3i/cxgb3i_init.c
new file mode 100644
index 0000000..091ecb4
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_init.c
@@ -0,0 +1,107 @@
+/* cxgb3i_init.c: Chelsio S3xx iSCSI driver.
+ *
+ * Copyright (c) 2008 Chelsio Communications, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * Written by: Karen Xie (kxie@chelsio.com)
+ */
+
+#include "cxgb3i.h"
+
+#define DRV_MODULE_NAME         "cxgb3i"
+#define DRV_MODULE_VERSION	"1.0.0"
+#define DRV_MODULE_RELDATE	"Jun. 1, 2008"
+
+static char version[] =
+	"Chelsio S3xx iSCSI Driver " DRV_MODULE_NAME
+	" v" DRV_MODULE_VERSION " (" DRV_MODULE_RELDATE ")\n";
+
+MODULE_AUTHOR("Karen Xie <kxie@chelsio.com>");
+MODULE_DESCRIPTION("Chelsio S3xx iSCSI Driver");
+MODULE_LICENSE("GPL");
+MODULE_VERSION(DRV_MODULE_VERSION);
+
+static void open_s3_dev(struct t3cdev *);
+static void close_s3_dev(struct t3cdev *);
+
+static cxgb3_cpl_handler_func cxgb3i_cpl_handlers[NUM_CPL_CMDS];
+static struct cxgb3_client t3c_client = {
+	.name = "iscsi_cxgb3",
+	.handlers = cxgb3i_cpl_handlers,
+	.add = open_s3_dev,
+	.remove = close_s3_dev,
+};
+
+/**
+ * open_s3_dev - register with cxgb3 LLD
+ * @t3dev:	cxgb3 adapter instance
+ */
+static void open_s3_dev(struct t3cdev *t3dev)
+{
+	static int vers_printed;
+
+	if (!vers_printed) {
+		printk(KERN_INFO "%s", version);
+		vers_printed = 1;
+	}
+
+	cxgb3i_sdev_add(t3dev, &t3c_client);
+	cxgb3i_adapter_add(t3dev);
+}
+
+/**
+ * close_s3_dev - de-register with cxgb3 LLD
+ * @t3dev:	cxgb3 adapter instance
+ */
+static void close_s3_dev(struct t3cdev *t3dev)
+{
+	cxgb3i_adapter_remove(t3dev);
+	cxgb3i_sdev_remove(t3dev);
+}
+
+/**
+ * cxgb3i_init_module - module init entry point
+ *
+ * initialize any driver wide global data structures and register itself
+ *	with the cxgb3 module
+ */
+static int __init cxgb3i_init_module(void)
+{
+	int err;
+
+	err = cxgb3i_sdev_init(cxgb3i_cpl_handlers);
+	if (err < 0)
+		return err;
+
+	err = cxgb3i_iscsi_init();
+	if (err < 0)
+		return err;
+
+	err = cxgb3i_pdu_init();
+	if (err < 0)
+		return err;
+
+	cxgb3_register_client(&t3c_client);
+
+	return 0;
+}
+
+/**
+ * cxgb3i_exit_module - module cleanup/exit entry point
+ *
+ * go through the driver hba list and for each hba, release any resource held.
+ *	and unregisters iscsi transport and the cxgb3 module
+ */
+static void __exit cxgb3i_exit_module(void)
+{
+	cxgb3_unregister_client(&t3c_client);
+	cxgb3i_pdu_cleanup();
+	cxgb3i_iscsi_cleanup();
+	cxgb3i_sdev_cleanup();
+}
+
+module_init(cxgb3i_init_module);
+module_exit(cxgb3i_exit_module);
diff --git a/drivers/scsi/cxgb3i/cxgb3i_iscsi.c b/drivers/scsi/cxgb3i/cxgb3i_iscsi.c
new file mode 100644
index 0000000..d83464b
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_iscsi.c
@@ -0,0 +1,951 @@
+/* cxgb3i_iscsi.c: Chelsio S3xx iSCSI driver.
+ *
+ * Copyright (c) 2008 Chelsio Communications, Inc.
+ * Copyright (c) 2008 Mike Christie
+ * Copyright (c) 2008 Red Hat, Inc.  All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * Written by: Karen Xie (kxie@chelsio.com)
+ */
+
+#include <linux/inet.h>
+#include <linux/crypto.h>
+#include <net/tcp.h>
+#include <scsi/scsi_cmnd.h>
+#include <scsi/scsi_device.h>
+#include <scsi/scsi_eh.h>
+#include <scsi/scsi_host.h>
+#include <scsi/scsi.h>
+#include <scsi/iscsi_proto.h>
+#include <scsi/libiscsi.h>
+#include <scsi/scsi_transport_iscsi.h>
+
+#include "cxgb3i.h"
+#include "cxgb3i_pdu.h"
+
+#ifdef __DEBUG_CXGB3I_TAG__
+#define cxgb3i_tag_debug	cxgb3i_log_debug
+#else
+#define cxgb3i_tag_debug(fmt...)
+#endif
+
+#ifdef __DEBUG_CXGB3I_API__
+#define cxgb3i_api_debug	cxgb3i_log_debug
+#else
+#define cxgb3i_api_debug(fmt...)
+#endif
+
+/*
+ * align pdu size to multiple of 512 for better performance
+ */
+#define align_pdu_size(n) do { n = (n) & (~511); } while (0)
+
+static struct scsi_transport_template *cxgb3i_scsi_transport;
+static struct scsi_host_template cxgb3i_host_template;
+static struct iscsi_transport cxgb3i_iscsi_transport;
+static unsigned char sw_tag_idx_bits;
+static unsigned char sw_tag_age_bits;
+
+static LIST_HEAD(cxgb3i_snic_list);
+static DEFINE_RWLOCK(cxgb3i_snic_rwlock);
+
+/**
+ * cxgb3i_adapter_add - init a s3 adapter structure and any h/w settings
+ * @t3dev: t3cdev adapter
+ * return the resulting cxgb3i_adapter struct
+ */
+struct cxgb3i_adapter *cxgb3i_adapter_add(struct t3cdev *t3dev)
+{
+	struct cxgb3i_adapter *snic;
+	struct adapter *adapter = tdev2adap(t3dev);
+	int i;
+
+	snic = kzalloc(sizeof(*snic), GFP_KERNEL);
+	if (!snic) {
+		cxgb3i_api_debug("cxgb3 %s, OOM.\n", t3dev->name);
+		return NULL;
+	}
+	spin_lock_init(&snic->lock);
+
+	snic->tdev = t3dev;
+	snic->pdev = adapter->pdev;
+	snic->tag_format.sw_bits = sw_tag_idx_bits + sw_tag_age_bits;
+
+	if (cxgb3i_adapter_ddp_init(t3dev, &snic->tag_format,
+				    &snic->tx_max_size,
+				    &snic->rx_max_size) < 0)
+		goto free_snic;
+
+	for_each_port(adapter, i) {
+		snic->hba[i] = cxgb3i_hba_host_add(snic, adapter->port[i]);
+		if (!snic->hba[i])
+			goto ulp_cleanup;
+	}
+	snic->hba_cnt = adapter->params.nports;
+
+	/* add to the list */
+	write_lock(&cxgb3i_snic_rwlock);
+	list_add_tail(&snic->list_head, &cxgb3i_snic_list);
+	write_unlock(&cxgb3i_snic_rwlock);
+
+	return snic;
+
+ulp_cleanup:
+	cxgb3i_adapter_ddp_cleanup(t3dev);
+free_snic:
+	kfree(snic);
+	return NULL;
+}
+
+/**
+ * cxgb3i_adapter_remove - release all the resources held and cleanup any
+ *	h/w settings
+ * @t3dev: t3cdev adapter
+ */
+void cxgb3i_adapter_remove(struct t3cdev *t3dev)
+{
+	int i;
+	struct cxgb3i_adapter *snic;
+
+	/* remove from the list */
+	write_lock(&cxgb3i_snic_rwlock);
+	list_for_each_entry(snic, &cxgb3i_snic_list, list_head) {
+		if (snic->tdev == t3dev) {
+			list_del(&snic->list_head);
+			break;
+		}
+	}
+	write_unlock(&cxgb3i_snic_rwlock);
+
+	if (snic) {
+		for (i = 0; i < snic->hba_cnt; i++) {
+			if (snic->hba[i]) {
+				cxgb3i_hba_host_remove(snic->hba[i]);
+				snic->hba[i] = NULL;
+			}
+		}
+
+		/* release ddp resources */
+		cxgb3i_adapter_ddp_cleanup(snic->tdev);
+		kfree(snic);
+	}
+}
+
+/**
+ * cxgb3i_hba_find_by_netdev - find the cxgb3i_hba structure with a given
+ *	net_device
+ * @t3dev: t3cdev adapter
+ */
+struct cxgb3i_hba *cxgb3i_hba_find_by_netdev(struct net_device *ndev)
+{
+	struct cxgb3i_adapter *snic;
+	int i;
+
+	read_lock(&cxgb3i_snic_rwlock);
+	list_for_each_entry(snic, &cxgb3i_snic_list, list_head) {
+		for (i = 0; i < snic->hba_cnt; i++) {
+			if (snic->hba[i]->ndev == ndev) {
+				read_unlock(&cxgb3i_snic_rwlock);
+				return snic->hba[i];
+			}
+		}
+	}
+	read_unlock(&cxgb3i_snic_rwlock);
+	return NULL;
+}
+
+/**
+ * cxgb3i_hba_host_add - register a new host with scsi/iscsi
+ * @snic: the cxgb3i adapter
+ * @ndev: associated net_device
+ */
+struct cxgb3i_hba *cxgb3i_hba_host_add(struct cxgb3i_adapter *snic,
+				       struct net_device *ndev)
+{
+	struct cxgb3i_hba *hba;
+	struct Scsi_Host *shost;
+	int err;
+
+	shost = iscsi_host_alloc(&cxgb3i_host_template,
+				 sizeof(struct cxgb3i_hba),
+				 CXGB3I_SCSI_QDEPTH_DFLT);
+	if (!shost) {
+		cxgb3i_log_info("iscsi_host_alloc failed.\n");
+		return NULL;
+	}
+
+	shost->transportt = cxgb3i_scsi_transport;
+	shost->max_lun = CXGB3I_MAX_LUN;
+	shost->max_id = CXGB3I_MAX_TARGET;
+	shost->max_channel = 0;
+	shost->max_cmd_len = 16;
+
+	hba = iscsi_host_priv(shost);
+	hba->snic = snic;
+	hba->ndev = ndev;
+	hba->shost = shost;
+
+	pci_dev_get(snic->pdev);
+	err = iscsi_host_add(shost, &snic->pdev->dev);
+	if (err) {
+		cxgb3i_log_info("iscsi_host_add failed.\n");
+		goto pci_dev_put;
+	}
+
+	cxgb3i_api_debug("shost 0x%p, hba 0x%p, no %u.\n",
+			 shost, hba, shost->host_no);
+
+	return hba;
+
+pci_dev_put:
+	pci_dev_put(snic->pdev);
+	scsi_host_put(shost);
+	return NULL;
+}
+
+/**
+ * cxgb3i_hba_host_remove - de-register the host with scsi/iscsi
+ * @hba: the cxgb3i hba
+ */
+void cxgb3i_hba_host_remove(struct cxgb3i_hba *hba)
+{
+	cxgb3i_api_debug("shost 0x%p, hba 0x%p, no %u.\n",
+			 hba->shost, hba, hba->shost->host_no);
+	iscsi_host_remove(hba->shost);
+	pci_dev_put(hba->snic->pdev);
+	iscsi_host_free(hba->shost);
+}
+
+/**
+ * cxgb3i_ep_connect - establish TCP connection to target portal
+ * @dst_addr:		target IP address
+ * @non_blocking:	blocking or non-blocking call
+ *
+ * Initiates a TCP/IP connection to the dst_addr
+ */
+static struct iscsi_endpoint *cxgb3i_ep_connect(struct sockaddr *dst_addr,
+						int non_blocking)
+{
+	struct iscsi_endpoint *ep;
+	struct cxgb3i_endpoint *cep;
+	struct cxgb3i_hba *hba;
+	struct s3_conn *c3cn = NULL;
+	int err = 0;
+
+	c3cn = cxgb3i_c3cn_create();
+	if (!c3cn) {
+		cxgb3i_log_info("ep connect OOM.\n");
+		err = -ENOMEM;
+		goto release_conn;
+	}
+
+	err = cxgb3i_c3cn_connect(c3cn, (struct sockaddr_in *)dst_addr);
+	if (err < 0) {
+		cxgb3i_log_info("ep connect failed.\n");
+		goto release_conn;
+	}
+	hba = cxgb3i_hba_find_by_netdev(c3cn->dst_cache->dev);
+	if (!hba) {
+		err = -ENOSPC;
+		cxgb3i_log_info("NOT going through cxgbi device.\n");
+		goto release_conn;
+	}
+	if (c3cn_is_closing(c3cn)) {
+		err = -ENOSPC;
+		cxgb3i_log_info("ep connect unable to connect.\n");
+		goto release_conn;
+	}
+
+	ep = iscsi_create_endpoint(sizeof(*cep));
+	if (!ep) {
+		err = -ENOMEM;
+		cxgb3i_log_info("iscsi alloc ep, OOM.\n");
+		goto release_conn;
+	}
+	cep = ep->dd_data;
+	cep->c3cn = c3cn;
+	cep->hba = hba;
+
+	cxgb3i_api_debug("ep 0x%p, 0x%p, c3cn 0x%p, hba 0x%p.\n",
+			  ep, cep, c3cn, hba);
+	return ep;
+
+release_conn:
+	cxgb3i_api_debug("conn 0x%p failed, release.\n", c3cn);
+	if (c3cn)
+		cxgb3i_c3cn_release(c3cn);
+	return ERR_PTR(err);
+}
+
+/**
+ * cxgb3i_ep_poll - polls for TCP connection establishement
+ * @ep:		TCP connection (endpoint) handle
+ * @timeout_ms:	timeout value in milli secs
+ *
+ * polls for TCP connect request to complete
+ */
+static int cxgb3i_ep_poll(struct iscsi_endpoint *ep, int timeout_ms)
+{
+	struct cxgb3i_endpoint *cep = ep->dd_data;
+	struct s3_conn *c3cn = cep->c3cn;
+
+	if (!c3cn_is_established(c3cn))
+		return 0;
+	cxgb3i_api_debug("ep 0x%p, c3cn 0x%p established.\n", ep, c3cn);
+	return 1;
+}
+
+/**
+ * cxgb3i_ep_disconnect - teardown TCP connection
+ * @ep:		TCP connection (endpoint) handle
+ *
+ * teardown TCP connection
+ */
+static void cxgb3i_ep_disconnect(struct iscsi_endpoint *ep)
+{
+	struct cxgb3i_endpoint *cep = ep->dd_data;
+	struct cxgb3i_conn *cconn = cep->cconn;
+
+	cxgb3i_api_debug("ep 0x%p, cep 0x%p.\n", ep, cep);
+
+	if (cconn && cconn->conn) {
+		/*
+		 * stop the xmit path so the xmit_pdu function is
+		 * not being called
+		 */
+		iscsi_suspend_tx(cconn->conn);
+
+		write_lock_bh(&cep->c3cn->callback_lock);
+		cep->c3cn->user_data = NULL;
+		cconn->cep = NULL;
+		write_unlock_bh(&cep->c3cn->callback_lock);
+	}
+
+	cxgb3i_api_debug("ep 0x%p, cep 0x%p, release c3cn 0x%p.\n",
+			 ep, cep, cep->c3cn);
+	cxgb3i_c3cn_release(cep->c3cn);
+	iscsi_destroy_endpoint(ep);
+}
+
+/**
+ * cxgb3i_session_create - create a new iscsi session
+ * @cmds_max:		max # of commands
+ * @qdepth:		scsi queue depth
+ * @initial_cmdsn:	initial iscsi CMDSN for this session
+ * @host_no:		pointer to return host no
+ *
+ * Creates a new iSCSI session
+ */
+static struct iscsi_cls_session *
+cxgb3i_session_create(struct iscsi_endpoint *ep, u16 cmds_max, u16 qdepth,
+		      u32 initial_cmdsn, u32 *host_no)
+{
+	struct cxgb3i_endpoint *cep;
+	struct cxgb3i_hba *hba;
+	struct Scsi_Host *shost;
+	struct iscsi_cls_session *cls_session;
+	struct iscsi_session *session;
+
+	if (!ep) {
+		cxgb3i_log_error("%s, missing endpoint.\n", __func__);
+		return NULL;
+	}
+
+	cep = ep->dd_data;
+	hba = cep->hba;
+	shost = hba->shost;
+	cxgb3i_api_debug("ep 0x%p, cep 0x%p, hba 0x%p.\n", ep, cep, hba);
+	BUG_ON(hba != iscsi_host_priv(shost));
+
+	*host_no = shost->host_no;
+
+	cls_session = iscsi_session_setup(&cxgb3i_iscsi_transport, shost,
+					  cmds_max,
+					  sizeof(struct iscsi_tcp_task),
+					  initial_cmdsn, ISCSI_MAX_TARGET);
+	if (!cls_session)
+		return NULL;
+	session = cls_session->dd_data;
+	if (iscsi_tcp_r2tpool_alloc(session))
+		goto remove_session;
+
+	return cls_session;
+
+remove_session:
+	iscsi_session_teardown(cls_session);
+	return NULL;
+}
+
+/**
+ * cxgb3i_session_destroy - destroys iscsi session
+ * @cls_session:	pointer to iscsi cls session
+ *
+ * Destroys an iSCSI session instance and releases its all resources held
+ */
+static void cxgb3i_session_destroy(struct iscsi_cls_session *cls_session)
+{
+	cxgb3i_api_debug("sess 0x%p.\n", cls_session);
+	iscsi_tcp_r2tpool_free(cls_session->dd_data);
+	iscsi_session_teardown(cls_session);
+}
+
+/**
+ * cxgb3i_conn_max_xmit_dlength -- check the max. xmit pdu segment size,
+ * reduce it to be within the hardware limit if needed
+ * @conn: iscsi connection
+ */
+static inline int cxgb3i_conn_max_xmit_dlength(struct iscsi_conn *conn)
+
+{
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	unsigned int max = min_t(unsigned int, ULP2_MAX_PDU_PAYLOAD,
+				 cconn->hba->snic->tx_max_size -
+				 ISCSI_PDU_NONPAYLOAD_MAX);
+
+	if (conn->max_xmit_dlength)
+		conn->max_xmit_dlength = min_t(unsigned int,
+						conn->max_xmit_dlength, max);
+	else
+		conn->max_xmit_dlength = max;
+	align_pdu_size(conn->max_xmit_dlength);
+	cxgb3i_log_info("conn 0x%p, max xmit %u.\n",
+			 conn, conn->max_xmit_dlength);
+	return 0;
+}
+
+/**
+ * cxgb3i_conn_max_recv_dlength -- check the max. recv pdu segment size against
+ * the hardware limit
+ * @conn: iscsi connection
+ * return 0 if the value is valid, < 0 otherwise.
+ */
+static inline int cxgb3i_conn_max_recv_dlength(struct iscsi_conn *conn)
+{
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	unsigned int max = min_t(unsigned int, ULP2_MAX_PDU_PAYLOAD,
+				 cconn->hba->snic->rx_max_size -
+				 ISCSI_PDU_NONPAYLOAD_MAX);
+
+	align_pdu_size(max);
+	if (conn->max_recv_dlength) {
+		if (conn->max_recv_dlength > max) {
+			cxgb3i_log_error("MaxRecvDataSegmentLength %u too big."
+					 " Need to be <= %u.\n",
+					 conn->max_recv_dlength, max);
+			return -EINVAL;
+		}
+		conn->max_recv_dlength = min_t(unsigned int,
+						conn->max_recv_dlength, max);
+		align_pdu_size(conn->max_recv_dlength);
+	} else
+		conn->max_recv_dlength = max;
+	cxgb3i_api_debug("conn 0x%p, max recv %u.\n",
+			 conn, conn->max_recv_dlength);
+	return 0;
+}
+
+/**
+ * cxgb3i_conn_create - create iscsi connection instance
+ * @cls_session:	pointer to iscsi cls session
+ * @cid:		iscsi cid
+ *
+ * Creates a new iSCSI connection instance for a given session
+ */
+static struct iscsi_cls_conn *cxgb3i_conn_create(struct iscsi_cls_session
+						 *cls_session, u32 cid)
+{
+	struct iscsi_cls_conn *cls_conn;
+	struct iscsi_conn *conn;
+	struct iscsi_tcp_conn *tcp_conn;
+	struct cxgb3i_conn *cconn;
+
+	cxgb3i_api_debug("sess 0x%p, cid %u.\n", cls_session, cid);
+
+	cls_conn = iscsi_tcp_conn_setup(cls_session, sizeof(*cconn), cid);
+	if (!cls_conn)
+		return NULL;
+	conn = cls_conn->dd_data;
+	tcp_conn = conn->dd_data;
+	cconn = tcp_conn->dd_data;
+
+	cconn->conn = conn;
+	return cls_conn;
+}
+
+/**
+ * cxgb3i_conn_bind - binds iscsi sess, conn and endpoint together
+ * @cls_session:	pointer to iscsi cls session
+ * @cls_conn:		pointer to iscsi cls conn
+ * @transport_eph:	64-bit EP handle
+ * @is_leading:		leading connection on this session?
+ *
+ * Binds together an iSCSI session, an iSCSI connection and a
+ *	TCP connection. This routine returns error code if the TCP
+ *	connection does not belong on the device iSCSI sess/conn is bound
+ */
+
+static int cxgb3i_conn_bind(struct iscsi_cls_session *cls_session,
+			    struct iscsi_cls_conn *cls_conn,
+			    u64 transport_eph, int is_leading)
+{
+	struct iscsi_conn *conn = cls_conn->dd_data;
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	struct cxgb3i_adapter *snic;
+	struct iscsi_endpoint *ep;
+	struct cxgb3i_endpoint *cep;
+	struct s3_conn *c3cn;
+	int err;
+
+	ep = iscsi_lookup_endpoint(transport_eph);
+	if (!ep)
+		return -EINVAL;
+
+	/* setup ddp pagesize */
+	cep = ep->dd_data;
+	c3cn = cep->c3cn;
+	snic = cep->hba->snic;
+	err = cxgb3i_setup_conn_host_pagesize(snic->tdev, c3cn->tid, 0);
+	if (err < 0)
+		return err;
+
+	cxgb3i_api_debug("ep 0x%p, cls sess 0x%p, cls conn 0x%p.\n",
+			 ep, cls_session, cls_conn);
+
+	err = iscsi_conn_bind(cls_session, cls_conn, is_leading);
+	if (err)
+		return -EINVAL;
+
+	/* calculate the tag idx bits needed for this conn based on cmds_max */
+	cconn->task_idx_bits = (__ilog2_u32(conn->session->cmds_max - 1)) + 1;
+	cxgb3i_api_debug("session cmds_max 0x%x, bits %u.\n",
+			 conn->session->cmds_max, cconn->task_idx_bits);
+
+	read_lock(&c3cn->callback_lock);
+	c3cn->user_data = conn;
+	cconn->hba = cep->hba;
+	cconn->cep = cep;
+	cep->cconn = cconn;
+	read_unlock(&c3cn->callback_lock);
+
+	cxgb3i_conn_max_xmit_dlength(conn);
+	cxgb3i_conn_max_recv_dlength(conn);
+
+	spin_lock_bh(&conn->session->lock);
+	sprintf(conn->portal_address, NIPQUAD_FMT,
+		NIPQUAD(c3cn->daddr.sin_addr.s_addr));
+	conn->portal_port = ntohs(c3cn->daddr.sin_port);
+	spin_unlock_bh(&conn->session->lock);
+
+	/* init recv engine */
+	iscsi_tcp_hdr_recv_prep(tcp_conn);
+
+	return 0;
+}
+
+/**
+ * cxgb3i_conn_get_param - return iscsi connection parameter to caller
+ * @cls_conn:	pointer to iscsi cls conn
+ * @param:	parameter type identifier
+ * @buf:	buffer pointer
+ *
+ * returns iSCSI connection parameters
+ */
+static int cxgb3i_conn_get_param(struct iscsi_cls_conn *cls_conn,
+				 enum iscsi_param param, char *buf)
+{
+	struct iscsi_conn *conn = cls_conn->dd_data;
+	int len;
+
+	cxgb3i_api_debug("cls_conn 0x%p, param %d.\n", cls_conn, param);
+
+	switch (param) {
+	case ISCSI_PARAM_CONN_PORT:
+		spin_lock_bh(&conn->session->lock);
+		len = sprintf(buf, "%hu\n", conn->portal_port);
+		spin_unlock_bh(&conn->session->lock);
+		break;
+	case ISCSI_PARAM_CONN_ADDRESS:
+		spin_lock_bh(&conn->session->lock);
+		len = sprintf(buf, "%s\n", conn->portal_address);
+		spin_unlock_bh(&conn->session->lock);
+		break;
+	default:
+		return iscsi_conn_get_param(cls_conn, param, buf);
+	}
+
+	return len;
+}
+
+/**
+ * cxgb3i_conn_set_param - set iscsi connection parameter
+ * @cls_conn:	pointer to iscsi cls conn
+ * @param:	parameter type identifier
+ * @buf:	buffer pointer
+ * @buflen:	buffer length
+ *
+ * set iSCSI connection parameters
+ */
+static int cxgb3i_conn_set_param(struct iscsi_cls_conn *cls_conn,
+				 enum iscsi_param param, char *buf, int buflen)
+{
+	struct iscsi_conn *conn = cls_conn->dd_data;
+	struct iscsi_session *session = conn->session;
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	struct cxgb3i_adapter *snic = cconn->hba->snic;
+	struct s3_conn *c3cn = cconn->cep->c3cn;
+	int value, err = 0;
+
+	switch (param) {
+	case ISCSI_PARAM_HDRDGST_EN:
+		err = iscsi_set_param(cls_conn, param, buf, buflen);
+		if (!err && conn->hdrdgst_en)
+			err = cxgb3i_setup_conn_digest(snic->tdev, c3cn->tid,
+							conn->hdrdgst_en,
+							conn->datadgst_en, 0);
+		break;
+	case ISCSI_PARAM_DATADGST_EN:
+		err = iscsi_set_param(cls_conn, param, buf, buflen);
+		if (!err && conn->datadgst_en)
+			err = cxgb3i_setup_conn_digest(snic->tdev, c3cn->tid,
+							conn->hdrdgst_en,
+							conn->datadgst_en, 0);
+		break;
+	case ISCSI_PARAM_MAX_R2T:
+		sscanf(buf, "%d", &value);
+		if (value <= 0 || !is_power_of_2(value))
+			return -EINVAL;
+		if (session->max_r2t == value)
+			break;
+		iscsi_tcp_r2tpool_free(session);
+		err = iscsi_set_param(cls_conn, param, buf, buflen);
+		if (!err && iscsi_tcp_r2tpool_alloc(session))
+			return -ENOMEM;
+	case ISCSI_PARAM_MAX_RECV_DLENGTH:
+		err = iscsi_set_param(cls_conn, param, buf, buflen);
+		if (!err)
+			err = cxgb3i_conn_max_recv_dlength(conn);
+		break;
+	case ISCSI_PARAM_MAX_XMIT_DLENGTH:
+		err = iscsi_set_param(cls_conn, param, buf, buflen);
+		if (!err)
+			err = cxgb3i_conn_max_xmit_dlength(conn);
+		break;
+	default:
+		return iscsi_set_param(cls_conn, param, buf, buflen);
+	}
+	return err;
+}
+
+/**
+ * cxgb3i_host_set_param - configure host (adapter) related parameters
+ * @shost:	scsi host pointer
+ * @param:	parameter type identifier
+ * @buf:	buffer pointer
+ */
+static int cxgb3i_host_set_param(struct Scsi_Host *shost,
+				 enum iscsi_host_param param,
+				 char *buf, int buflen)
+{
+	struct cxgb3i_hba *hba = iscsi_host_priv(shost);
+
+	cxgb3i_api_debug("param %d, buf %s.\n", param, buf);
+
+	switch (param) {
+	case ISCSI_HOST_PARAM_IPADDRESS:
+	{
+		__be32 addr = in_aton(buf);
+		cxgb3i_set_private_ipv4addr(hba->ndev, addr);
+		return 0;
+	}
+	case ISCSI_HOST_PARAM_HWADDRESS:
+	case ISCSI_HOST_PARAM_NETDEV_NAME:
+		/* ignore */
+		return 0;
+	default:
+		return iscsi_host_set_param(shost, param, buf, buflen);
+	}
+}
+
+/**
+ * cxgb3i_host_get_param - returns host (adapter) related parameters
+ * @shost:	scsi host pointer
+ * @param:	parameter type identifier
+ * @buf:	buffer pointer
+ */
+static int cxgb3i_host_get_param(struct Scsi_Host *shost,
+				 enum iscsi_host_param param, char *buf)
+{
+	struct cxgb3i_hba *hba = iscsi_host_priv(shost);
+	int len = 0;
+
+	cxgb3i_api_debug("hba %s, param %d.\n", hba->ndev->name, param);
+
+	switch (param) {
+	case ISCSI_HOST_PARAM_HWADDRESS:
+		len = sysfs_format_mac(buf, hba->ndev->dev_addr, 6);
+		break;
+	case ISCSI_HOST_PARAM_NETDEV_NAME:
+		len = sprintf(buf, "%s\n", hba->ndev->name);
+		break;
+	case ISCSI_HOST_PARAM_IPADDRESS:
+	{
+		__be32 addr;
+
+		addr = cxgb3i_get_private_ipv4addr(hba->ndev);
+		len = sprintf(buf, NIPQUAD_FMT, NIPQUAD(addr));
+		break;
+	}
+	default:
+		return iscsi_host_get_param(shost, param, buf);
+	}
+	return len;
+}
+
+/**
+ * cxgb3i_conn_get_stats - returns iSCSI stats
+ * @cls_conn:	pointer to iscsi cls conn
+ * @stats:	pointer to iscsi statistic struct
+ */
+static void cxgb3i_conn_get_stats(struct iscsi_cls_conn *cls_conn,
+				  struct iscsi_stats *stats)
+{
+	struct iscsi_conn *conn = cls_conn->dd_data;
+
+	stats->txdata_octets = conn->txdata_octets;
+	stats->rxdata_octets = conn->rxdata_octets;
+	stats->scsicmd_pdus = conn->scsicmd_pdus_cnt;
+	stats->dataout_pdus = conn->dataout_pdus_cnt;
+	stats->scsirsp_pdus = conn->scsirsp_pdus_cnt;
+	stats->datain_pdus = conn->datain_pdus_cnt;
+	stats->r2t_pdus = conn->r2t_pdus_cnt;
+	stats->tmfcmd_pdus = conn->tmfcmd_pdus_cnt;
+	stats->tmfrsp_pdus = conn->tmfrsp_pdus_cnt;
+	stats->digest_err = 0;
+	stats->timeout_err = 0;
+	stats->custom_length = 1;
+	strcpy(stats->custom[0].desc, "eh_abort_cnt");
+	stats->custom[0].value = conn->eh_abort_cnt;
+}
+
+/**
+ * cxgb3i_parse_itt - get the idx and age bits from a given tag
+ * @conn:	iscsi connection
+ * @itt:	itt tag
+ * @idx:	task index, filled in by this function
+ * @age:	session age, filled in by this function
+ */
+static void cxgb3i_parse_itt(struct iscsi_conn *conn, itt_t itt,
+			     int *idx, int *age)
+{
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	struct cxgb3i_adapter *snic = cconn->hba->snic;
+	u32 tag = ntohl((__force u32) itt);
+	u32 sw_bits;
+
+	sw_bits = cxgb3i_tag_nonrsvd_bits(&snic->tag_format, tag);
+	if (idx)
+		*idx = sw_bits & ((1 << cconn->task_idx_bits) - 1);
+	if (age)
+		*age = (sw_bits >> cconn->task_idx_bits) & ISCSI_AGE_MASK;
+
+	cxgb3i_tag_debug("parse tag 0x%x/0x%x, sw 0x%x, itt 0x%x, age 0x%x.\n",
+			 tag, itt, sw_bits, idx ? *idx : 0xFFFFF,
+			 age ? *age : 0xFF);
+}
+
+/**
+ * cxgb3i_reserve_itt - generate tag for a give task
+ * Try to set up ddp for a scsi read task.
+ * @task: iscsi task
+ * @hdr_itt: tag, filled in by this function
+ */
+int cxgb3i_reserve_itt(struct iscsi_task *task, itt_t *hdr_itt)
+{
+	struct scsi_cmnd *sc = task->sc;
+	struct iscsi_conn *conn = task->conn;
+	struct iscsi_session *sess = conn->session;
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	struct cxgb3i_adapter *snic = cconn->hba->snic;
+	struct cxgb3i_tag_format *tformat = &snic->tag_format;
+	u32 sw_tag = (sess->age << cconn->task_idx_bits) | task->itt;
+	u32 tag;
+	int err = -EINVAL;
+
+	if (sc &&
+	    (scsi_bidi_cmnd(sc) || sc->sc_data_direction == DMA_FROM_DEVICE) &&
+	    cxgb3i_sw_tag_usable(tformat, sw_tag)) {
+		struct s3_conn *c3cn = cconn->cep->c3cn;
+		struct cxgb3i_gather_list *gl;
+
+		gl = cxgb3i_ddp_make_gl(scsi_in(sc)->length,
+					scsi_in(sc)->table.sgl,
+					scsi_in(sc)->table.nents,
+					snic->pdev,
+					GFP_ATOMIC);
+		if (gl) {
+			tag = sw_tag;
+			err = cxgb3i_ddp_tag_reserve(snic->tdev, c3cn->tid,
+						     tformat, &tag,
+						     gl, GFP_ATOMIC);
+			if (err < 0)
+				cxgb3i_ddp_release_gl(gl, snic->pdev);
+		}
+	}
+
+	if (err < 0)
+		tag = cxgb3i_set_non_ddp_tag(tformat, sw_tag);
+	/* the itt need to sent in big-endian order */
+	*hdr_itt = (__force itt_t)htonl(tag);
+
+	cxgb3i_tag_debug("new tag 0x%x/0x%x (itt 0x%x, age 0x%x).\n",
+			 tag, *hdr_itt, task->itt, sess->age);
+	return 0;
+}
+
+/**
+ * cxgb3i_release_itt - release the tag for a given task
+ * if the tag is a ddp tag, release the ddp setup
+ * @task:	iscsi task
+ * @hdr_itt:	tag
+ */
+void cxgb3i_release_itt(struct iscsi_task *task, itt_t hdr_itt)
+{
+	struct scsi_cmnd *sc = task->sc;
+	struct iscsi_tcp_conn *tcp_conn = task->conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	struct cxgb3i_adapter *snic = cconn->hba->snic;
+	struct cxgb3i_tag_format *tformat = &snic->tag_format;
+	u32 tag = ntohl((__force u32)hdr_itt);
+
+	cxgb3i_tag_debug("release tag 0x%x.\n", tag);
+
+	if (sc &&
+	    (scsi_bidi_cmnd(sc) || sc->sc_data_direction == DMA_FROM_DEVICE) &&
+	    cxgb3i_is_ddp_tag(tformat, tag))
+		cxgb3i_ddp_tag_release(snic->tdev, tag);
+}
+
+/**
+ * cxgb3i_host_template -- Scsi_Host_Template structure
+ *	used when registering with the scsi mid layer
+ */
+static struct scsi_host_template cxgb3i_host_template = {
+	.module			= THIS_MODULE,
+	.name			= "Chelsio S3xx iSCSI Initiator",
+	.proc_name		= "cxgb3i",
+	.queuecommand		= iscsi_queuecommand,
+	.change_queue_depth	= iscsi_change_queue_depth,
+	.can_queue		= 128 * (ISCSI_DEF_XMIT_CMDS_MAX - 1),
+	.sg_tablesize		= SG_ALL,
+	.max_sectors		= 0xFFFF,
+	.cmd_per_lun		= ISCSI_DEF_CMD_PER_LUN,
+	.eh_abort_handler	= iscsi_eh_abort,
+	.eh_device_reset_handler = iscsi_eh_device_reset,
+	.eh_target_reset_handler = iscsi_eh_target_reset,
+	.use_clustering		= DISABLE_CLUSTERING,
+	.this_id		= -1,
+};
+
+static struct iscsi_transport cxgb3i_iscsi_transport = {
+	.owner			= THIS_MODULE,
+	.name			= "cxgb3i",
+	.caps			= CAP_RECOVERY_L0 | CAP_MULTI_R2T | CAP_HDRDGST
+				| CAP_DATADGST | CAP_DIGEST_OFFLOAD |
+				CAP_PADDING_OFFLOAD,
+	.param_mask		= ISCSI_MAX_RECV_DLENGTH |
+				ISCSI_MAX_XMIT_DLENGTH |
+				ISCSI_HDRDGST_EN |
+				ISCSI_DATADGST_EN |
+				ISCSI_INITIAL_R2T_EN |
+				ISCSI_MAX_R2T |
+				ISCSI_IMM_DATA_EN |
+				ISCSI_FIRST_BURST |
+				ISCSI_MAX_BURST |
+				ISCSI_PDU_INORDER_EN |
+				ISCSI_DATASEQ_INORDER_EN |
+				ISCSI_ERL |
+				ISCSI_CONN_PORT |
+				ISCSI_CONN_ADDRESS |
+				ISCSI_EXP_STATSN |
+				ISCSI_PERSISTENT_PORT |
+				ISCSI_PERSISTENT_ADDRESS |
+				ISCSI_TARGET_NAME | ISCSI_TPGT |
+				ISCSI_USERNAME | ISCSI_PASSWORD |
+				ISCSI_USERNAME_IN | ISCSI_PASSWORD_IN |
+				ISCSI_FAST_ABORT | ISCSI_ABORT_TMO |
+				ISCSI_LU_RESET_TMO |
+				ISCSI_PING_TMO | ISCSI_RECV_TMO |
+				ISCSI_IFACE_NAME | ISCSI_INITIATOR_NAME,
+	.host_param_mask	= ISCSI_HOST_HWADDRESS | ISCSI_HOST_IPADDRESS |
+			ISCSI_HOST_INITIATOR_NAME | ISCSI_HOST_NETDEV_NAME,
+	.get_host_param		= cxgb3i_host_get_param,
+	.set_host_param		= cxgb3i_host_set_param,
+	/* session management */
+	.create_session		= cxgb3i_session_create,
+	.destroy_session	= cxgb3i_session_destroy,
+	.get_session_param	= iscsi_session_get_param,
+	/* connection management */
+	.create_conn		= cxgb3i_conn_create,
+	.bind_conn		= cxgb3i_conn_bind,
+	.destroy_conn		= iscsi_tcp_conn_teardown,
+	.start_conn		= iscsi_conn_start,
+	.stop_conn		= iscsi_conn_stop,
+	.get_conn_param		= cxgb3i_conn_get_param,
+	.set_param		= cxgb3i_conn_set_param,
+	.get_stats		= cxgb3i_conn_get_stats,
+	/* pdu xmit req. from user space */
+	.send_pdu		= iscsi_conn_send_pdu,
+	/* task */
+	.init_task		= iscsi_tcp_task_init,
+	.xmit_task		= iscsi_tcp_task_xmit,
+	.cleanup_task		= cxgb3i_conn_cleanup_task,
+
+	/* pdu */
+	.alloc_pdu		= cxgb3i_conn_alloc_pdu,
+	.init_pdu		= cxgb3i_conn_init_pdu,
+	.xmit_pdu		= cxgb3i_conn_xmit_pdu,
+	.parse_pdu_itt		= cxgb3i_parse_itt,
+
+	/* TCP connect/disconnect */
+	.ep_connect		= cxgb3i_ep_connect,
+	.ep_poll		= cxgb3i_ep_poll,
+	.ep_disconnect		= cxgb3i_ep_disconnect,
+	/* Error recovery timeout call */
+	.session_recovery_timedout = iscsi_session_recovery_timedout,
+};
+
+int cxgb3i_iscsi_init(void)
+{
+	sw_tag_idx_bits = (__ilog2_u32(ISCSI_ITT_MASK)) + 1;
+	sw_tag_age_bits = (__ilog2_u32(ISCSI_AGE_MASK)) + 1;
+	cxgb3i_log_info("tag itt 0x%x, %u bits, age 0x%x, %u bits.\n",
+			ISCSI_ITT_MASK, sw_tag_idx_bits,
+			ISCSI_AGE_MASK, sw_tag_age_bits);
+
+	cxgb3i_scsi_transport =
+	    iscsi_register_transport(&cxgb3i_iscsi_transport);
+	if (!cxgb3i_scsi_transport) {
+		cxgb3i_log_error("Could not register cxgb3i transport.\n");
+		return -ENODEV;
+	}
+	cxgb3i_api_debug("cxgb3i transport 0x%p.\n", cxgb3i_scsi_transport);
+	return 0;
+}
+
+void cxgb3i_iscsi_cleanup(void)
+{
+	if (cxgb3i_scsi_transport) {
+		cxgb3i_api_debug("cxgb3i transport 0x%p.\n",
+				 cxgb3i_scsi_transport);
+		iscsi_unregister_transport(&cxgb3i_iscsi_transport);
+	}
+}
diff --git a/drivers/scsi/cxgb3i/cxgb3i_offload.c b/drivers/scsi/cxgb3i/cxgb3i_offload.c
new file mode 100644
index 0000000..5f16081b
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_offload.c
@@ -0,0 +1,1810 @@
+/*
+ * cxgb3i_offload.c: Chelsio S3xx iscsi offloaded tcp connection management
+ *
+ * Copyright (C) 2003-2008 Chelsio Communications.  All rights reserved.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the LICENSE file included in this
+ * release for licensing terms and conditions.
+ *
+ * Written by:	Dimitris Michailidis (dm@chelsio.com)
+ *		Karen Xie (kxie@chelsio.com)
+ */
+
+#include <linux/if_vlan.h>
+#include <linux/version.h>
+
+#include "cxgb3_defs.h"
+#include "cxgb3_ctl_defs.h"
+#include "firmware_exports.h"
+#include "cxgb3i_offload.h"
+#include "cxgb3i_pdu.h"
+#include "cxgb3i_ddp.h"
+
+#ifdef __DEBUG_C3CN_CONN__
+#define c3cn_conn_debug         cxgb3i_log_info
+#else
+#define c3cn_conn_debug(fmt...)
+#endif
+
+#ifdef __DEBUG_C3CN_TX__
+#define c3cn_tx_debug         cxgb3i_log_debug
+#else
+#define c3cn_tx_debug(fmt...)
+#endif
+
+#ifdef __DEBUG_C3CN_RX__
+#define c3cn_rx_debug         cxgb3i_log_debug
+#else
+#define c3cn_rx_debug(fmt...)
+#endif
+
+/*
+ * module parameters releated to offloaded iscsi connection
+ */
+static int cxgb3_rcv_win = 256 * 1024;
+module_param(cxgb3_rcv_win, int, 0644);
+MODULE_PARM_DESC(cxgb3_rcv_win, "TCP receive window in bytes (default=256KB)");
+
+static int cxgb3_snd_win = 64 * 1024;
+module_param(cxgb3_snd_win, int, 0644);
+MODULE_PARM_DESC(cxgb3_snd_win, "TCP send window in bytes (default=64KB)");
+
+static int cxgb3_rx_credit_thres = 10 * 1024;
+module_param(cxgb3_rx_credit_thres, int, 0644);
+MODULE_PARM_DESC(rx_credit_thres,
+		 "RX credits return threshold in bytes (default=10KB)");
+
+static unsigned int cxgb3_max_connect = 8 * 1024;
+module_param(cxgb3_max_connect, uint, 0644);
+MODULE_PARM_DESC(cxgb3_max_connect, "Max. # of connections (default=8092)");
+
+static unsigned int cxgb3_sport_base = 20000;
+module_param(cxgb3_sport_base, uint, 0644);
+MODULE_PARM_DESC(cxgb3_sport_base, "starting port number (default=20000)");
+
+/*
+ * cxgb3i tcp connection data(per adapter) list
+ */
+static LIST_HEAD(cdata_list);
+static DEFINE_RWLOCK(cdata_rwlock);
+
+static int c3cn_push_tx_frames(struct s3_conn *c3cn, int req_completion);
+static void c3cn_release_offload_resources(struct s3_conn *c3cn);
+
+/*
+ * iscsi source port management
+ *
+ * Find a free source port in the port allocation map. We use a very simple
+ * rotor scheme to look for the next free port.
+ *
+ * If a source port has been specified make sure that it doesn't collide with
+ * our normal source port allocation map.  If it's outside the range of our
+ * allocation/deallocation scheme just let them use it.
+ *
+ * If the source port is outside our allocation range, the caller is
+ * responsible for keeping track of their port usage.
+ */
+static int c3cn_get_port(struct s3_conn *c3cn, struct cxgb3i_sdev_data *cdata)
+{
+	unsigned int start;
+	int idx;
+
+	if (!cdata)
+		goto error_out;
+
+	if (c3cn->saddr.sin_port != 0) {
+		idx = ntohs(c3cn->saddr.sin_port) - cxgb3_sport_base;
+		if (idx < 0 || idx >= cxgb3_max_connect)
+			return 0;
+		if (!test_and_set_bit(idx, cdata->sport_map))
+			return -EADDRINUSE;
+	}
+
+	/* the sport_map_next may not be accurate but that is okay, sport_map
+	   should be */
+	start = idx = cdata->sport_map_next;
+	do {
+		if (++idx >= cxgb3_max_connect)
+			idx = 0;
+		if (!(test_and_set_bit(idx, cdata->sport_map))) {
+			c3cn->saddr.sin_port = htons(cxgb3_sport_base + idx);
+			cdata->sport_map_next = idx;
+			c3cn_conn_debug("%s reserve port %u.\n",
+					cdata->cdev->name,
+					cxgb3_sport_base + idx);
+			return 0;
+		}
+	} while (idx != start);
+
+error_out:
+	return -EADDRNOTAVAIL;
+}
+
+static void c3cn_put_port(struct s3_conn *c3cn)
+{
+	struct cxgb3i_sdev_data *cdata = CXGB3_SDEV_DATA(c3cn->cdev);
+
+	if (c3cn->saddr.sin_port) {
+		int idx = ntohs(c3cn->saddr.sin_port) - cxgb3_sport_base;
+
+		c3cn->saddr.sin_port = 0;
+		if (idx < 0 || idx >= cxgb3_max_connect)
+			return;
+		clear_bit(idx, cdata->sport_map);
+		c3cn_conn_debug("%s, release port %u.\n",
+				cdata->cdev->name, cxgb3_sport_base + idx);
+	}
+}
+
+static inline void c3cn_set_flag(struct s3_conn *c3cn, enum c3cn_flags flag)
+{
+	__set_bit(flag, &c3cn->flags);
+	c3cn_conn_debug("c3cn 0x%p, set %d, s %u, f 0x%lx.\n",
+			c3cn, flag, c3cn->state, c3cn->flags);
+}
+
+static inline void c3cn_clear_flag(struct s3_conn *c3cn, enum c3cn_flags flag)
+{
+	__clear_bit(flag, &c3cn->flags);
+	c3cn_conn_debug("c3cn 0x%p, clear %d, s %u, f 0x%lx.\n",
+			c3cn, flag, c3cn->state, c3cn->flags);
+}
+
+static inline int c3cn_flag(struct s3_conn *c3cn, enum c3cn_flags flag)
+{
+	if (c3cn == NULL)
+		return 0;
+	return test_bit(flag, &c3cn->flags);
+}
+
+static void c3cn_set_state(struct s3_conn *c3cn, int state)
+{
+	c3cn_conn_debug("c3cn 0x%p state -> %u.\n", c3cn, state);
+	c3cn->state = state;
+}
+
+static inline void c3cn_hold(struct s3_conn *c3cn)
+{
+	atomic_inc(&c3cn->refcnt);
+}
+
+static inline void c3cn_put(struct s3_conn *c3cn)
+{
+	if (atomic_dec_and_test(&c3cn->refcnt)) {
+		c3cn_conn_debug("free c3cn 0x%p, s %u, f 0x%lx.\n",
+				c3cn, c3cn->state, c3cn->flags);
+		kfree(c3cn);
+	}
+}
+
+static void c3cn_closed(struct s3_conn *c3cn)
+{
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			 c3cn, c3cn->state, c3cn->flags);
+
+	c3cn_put_port(c3cn);
+	c3cn_release_offload_resources(c3cn);
+	c3cn_set_state(c3cn, C3CN_STATE_CLOSED);
+	cxgb3i_conn_closing(c3cn);
+}
+
+/*
+ * CPL (Chelsio Protocol Language) defines a message passing interface between
+ * the host driver and T3 asic.
+ * The section below implments CPLs that related to iscsi tcp connection
+ * open/close/abort and data send/receive.
+ */
+
+/*
+ * CPL connection active open request: host ->
+ */
+static unsigned int find_best_mtu(const struct t3c_data *d, unsigned short mtu)
+{
+	int i = 0;
+
+	while (i < d->nmtus - 1 && d->mtus[i + 1] <= mtu)
+		++i;
+	return i;
+}
+
+static unsigned int select_mss(struct s3_conn *c3cn, unsigned int pmtu)
+{
+	unsigned int idx;
+	struct dst_entry *dst = c3cn->dst_cache;
+	struct t3cdev *cdev = c3cn->cdev;
+	const struct t3c_data *td = T3C_DATA(cdev);
+	u16 advmss = dst_metric(dst, RTAX_ADVMSS);
+
+	if (advmss > pmtu - 40)
+		advmss = pmtu - 40;
+	if (advmss < td->mtus[0] - 40)
+		advmss = td->mtus[0] - 40;
+	idx = find_best_mtu(td, advmss + 40);
+	return idx;
+}
+
+static inline int compute_wscale(int win)
+{
+	int wscale = 0;
+	while (wscale < 14 && (65535<<wscale) < win)
+		wscale++;
+	return wscale;
+}
+
+static inline unsigned int calc_opt0h(struct s3_conn *c3cn)
+{
+	int wscale = compute_wscale(cxgb3_rcv_win);
+	return  V_KEEP_ALIVE(1) |
+		F_TCAM_BYPASS |
+		V_WND_SCALE(wscale) |
+		V_MSS_IDX(c3cn->mss_idx);
+}
+
+static inline unsigned int calc_opt0l(struct s3_conn *c3cn)
+{
+	return  V_ULP_MODE(ULP_MODE_ISCSI) |
+		V_RCV_BUFSIZ(cxgb3_rcv_win>>10);
+}
+
+static void make_act_open_req(struct s3_conn *c3cn, struct sk_buff *skb,
+			      unsigned int atid, const struct l2t_entry *e)
+{
+	struct cpl_act_open_req *req;
+
+	c3cn_conn_debug("c3cn 0x%p, atid 0x%x.\n", c3cn, atid);
+
+	skb->priority = CPL_PRIORITY_SETUP;
+	req = (struct cpl_act_open_req *)__skb_put(skb, sizeof(*req));
+	req->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_FORWARD));
+	OPCODE_TID(req) = htonl(MK_OPCODE_TID(CPL_ACT_OPEN_REQ, atid));
+	req->local_port = c3cn->saddr.sin_port;
+	req->peer_port = c3cn->daddr.sin_port;
+	req->local_ip = c3cn->saddr.sin_addr.s_addr;
+	req->peer_ip = c3cn->daddr.sin_addr.s_addr;
+	req->opt0h = htonl(calc_opt0h(c3cn) | V_L2T_IDX(e->idx) |
+			   V_TX_CHANNEL(e->smt_idx));
+	req->opt0l = htonl(calc_opt0l(c3cn));
+	req->params = 0;
+}
+
+static void fail_act_open(struct s3_conn *c3cn, int errno)
+{
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+	c3cn->err = errno;
+	c3cn_closed(c3cn);
+}
+
+static void act_open_req_arp_failure(struct t3cdev *dev, struct sk_buff *skb)
+{
+	struct s3_conn *c3cn = (struct s3_conn *)skb->sk;
+
+	c3cn_conn_debug("c3cn 0x%p, state %u.\n", c3cn, c3cn->state);
+
+	c3cn_hold(c3cn);
+	spin_lock_bh(&c3cn->lock);
+	if (c3cn->state == C3CN_STATE_CONNECTING)
+		fail_act_open(c3cn, EHOSTUNREACH);
+	spin_unlock_bh(&c3cn->lock);
+	c3cn_put(c3cn);
+	__kfree_skb(skb);
+}
+
+/*
+ * CPL connection close request: host ->
+ *
+ * Close a connection by sending a CPL_CLOSE_CON_REQ message and queue it to
+ * the write queue (i.e., after any unsent txt data).
+ */
+static void skb_entail(struct s3_conn *c3cn, struct sk_buff *skb,
+		       int flags)
+{
+	CXGB3_SKB_CB(skb)->seq = c3cn->write_seq;
+	CXGB3_SKB_CB(skb)->flags = flags;
+	__skb_queue_tail(&c3cn->write_queue, skb);
+}
+
+static void send_close_req(struct s3_conn *c3cn)
+{
+	struct sk_buff *skb = c3cn->cpl_close;
+	struct cpl_close_con_req *req = (struct cpl_close_con_req *)skb->head;
+	unsigned int tid = c3cn->tid;
+
+	c3cn_conn_debug("c3cn 0x%p, state 0x%x, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	c3cn->cpl_close = NULL;
+
+	req->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_OFLD_CLOSE_CON));
+	req->wr.wr_lo = htonl(V_WR_TID(tid));
+	OPCODE_TID(req) = htonl(MK_OPCODE_TID(CPL_CLOSE_CON_REQ, tid));
+	req->rsvd = htonl(c3cn->write_seq);
+
+	skb_entail(c3cn, skb, C3CB_FLAG_NO_APPEND);
+	if (c3cn->state != C3CN_STATE_CONNECTING)
+		c3cn_push_tx_frames(c3cn, 1);
+}
+
+/*
+ * CPL connection abort request: host ->
+ *
+ * Send an ABORT_REQ message. Makes sure we do not send multiple ABORT_REQs
+ * for the same connection and also that we do not try to send a message
+ * after the connection has closed.
+ */
+static void abort_arp_failure(struct t3cdev *cdev, struct sk_buff *skb)
+{
+	struct cpl_abort_req *req = cplhdr(skb);
+
+	c3cn_conn_debug("tdev 0x%p.\n", cdev);
+
+	req->cmd = CPL_ABORT_NO_RST;
+	cxgb3_ofld_send(cdev, skb);
+}
+
+static inline void c3cn_purge_write_queue(struct s3_conn *c3cn)
+{
+	struct sk_buff *skb;
+
+	while ((skb = __skb_dequeue(&c3cn->write_queue)))
+		__kfree_skb(skb);
+}
+
+static void send_abort_req(struct s3_conn *c3cn)
+{
+	struct sk_buff *skb = c3cn->cpl_abort_req;
+	struct cpl_abort_req *req;
+	unsigned int tid = c3cn->tid;
+
+	if (unlikely(c3cn->state == C3CN_STATE_ABORTING) || !skb ||
+		     !c3cn->cdev)
+		return;
+
+	c3cn_set_state(c3cn, C3CN_STATE_ABORTING);
+
+	c3cn_conn_debug("c3cn 0x%p, flag ABORT_RPL + ABORT_SHUT.\n", c3cn);
+
+	c3cn_set_flag(c3cn, C3CN_ABORT_RPL_PENDING);
+
+	/* Purge the send queue so we don't send anything after an abort. */
+	c3cn_purge_write_queue(c3cn);
+
+	c3cn->cpl_abort_req = NULL;
+	req = (struct cpl_abort_req *)skb->head;
+
+	skb->priority = CPL_PRIORITY_DATA;
+	set_arp_failure_handler(skb, abort_arp_failure);
+
+	req->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_OFLD_HOST_ABORT_CON_REQ));
+	req->wr.wr_lo = htonl(V_WR_TID(tid));
+	OPCODE_TID(req) = htonl(MK_OPCODE_TID(CPL_ABORT_REQ, tid));
+	req->rsvd0 = htonl(c3cn->snd_nxt);
+	req->rsvd1 = !c3cn_flag(c3cn, C3CN_TX_DATA_SENT);
+	req->cmd = CPL_ABORT_SEND_RST;
+
+	l2t_send(c3cn->cdev, skb, c3cn->l2t);
+}
+
+/*
+ * CPL connection abort reply: host ->
+ *
+ * Send an ABORT_RPL message in response of the ABORT_REQ received.
+ */
+static void send_abort_rpl(struct s3_conn *c3cn, int rst_status)
+{
+	struct sk_buff *skb = c3cn->cpl_abort_rpl;
+	struct cpl_abort_rpl *rpl = (struct cpl_abort_rpl *)skb->head;
+
+	c3cn->cpl_abort_rpl = NULL;
+
+	skb->priority = CPL_PRIORITY_DATA;
+	rpl->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_OFLD_HOST_ABORT_CON_RPL));
+	rpl->wr.wr_lo = htonl(V_WR_TID(c3cn->tid));
+	OPCODE_TID(rpl) = htonl(MK_OPCODE_TID(CPL_ABORT_RPL, c3cn->tid));
+	rpl->cmd = rst_status;
+
+	cxgb3_ofld_send(c3cn->cdev, skb);
+}
+
+/*
+ * CPL connection rx data ack: host ->
+ * Send RX credits through an RX_DATA_ACK CPL message. Returns the number of
+ * credits sent.
+ */
+static u32 send_rx_credits(struct s3_conn *c3cn, u32 credits, u32 dack)
+{
+	struct sk_buff *skb;
+	struct cpl_rx_data_ack *req;
+
+	skb = alloc_skb(sizeof(*req), GFP_ATOMIC);
+	if (!skb)
+		return 0;
+
+	req = (struct cpl_rx_data_ack *)__skb_put(skb, sizeof(*req));
+	req->wr.wr_hi = htonl(V_WR_OP(FW_WROPCODE_FORWARD));
+	OPCODE_TID(req) = htonl(MK_OPCODE_TID(CPL_RX_DATA_ACK, c3cn->tid));
+	req->credit_dack = htonl(dack | V_RX_CREDITS(credits));
+	skb->priority = CPL_PRIORITY_ACK;
+	cxgb3_ofld_send(c3cn->cdev, skb);
+	return credits;
+}
+
+/*
+ * CPL connection tx data: host ->
+ *
+ * Send iscsi PDU via TX_DATA CPL message. Returns the number of
+ * credits sent.
+ * Each TX_DATA consumes work request credit (wrs), so we need to keep track of
+ * how many we've used so far and how many are pending (i.e., yet ack'ed by T3).
+ */
+
+/*
+ * For ULP connections HW may inserts digest bytes into the pdu. Those digest
+ * bytes are not sent by the host but are part of the TCP payload and therefore
+ * consume TCP sequence space.
+ */
+static const unsigned int cxgb3_ulp_extra_len[] = { 0, 4, 4, 8 };
+static inline unsigned int ulp_extra_len(const struct sk_buff *skb)
+{
+	return cxgb3_ulp_extra_len[skb_ulp_mode(skb) & 3];
+}
+
+static unsigned int wrlen __read_mostly;
+
+/*
+ * The number of WRs needed for an skb depends on the number of fragments
+ * in the skb and whether it has any payload in its main body.  This maps the
+ * length of the gather list represented by an skb into the # of necessary WRs.
+ *
+ * The max. length of an skb is controlled by the max pdu size which is ~16K.
+ * Also, assume the min. fragment length is the sector size (512), then add
+ * extra fragment counts for iscsi bhs and payload padding.
+ */
+#define SKB_WR_LIST_SIZE	(16384/512 + 3)
+static unsigned int skb_wrs[SKB_WR_LIST_SIZE] __read_mostly;
+
+static void s3_init_wr_tab(unsigned int wr_len)
+{
+	int i;
+
+	if (skb_wrs[1])		/* already initialized */
+		return;
+
+	for (i = 1; i < SKB_WR_LIST_SIZE; i++) {
+		int sgl_len = (3 * i) / 2 + (i & 1);
+
+		sgl_len += 3;
+		skb_wrs[i] = (sgl_len <= wr_len
+			      ? 1 : 1 + (sgl_len - 2) / (wr_len - 1));
+	}
+
+	wrlen = wr_len * 8;
+}
+
+static inline void reset_wr_list(struct s3_conn *c3cn)
+{
+	c3cn->wr_pending_head = NULL;
+}
+
+/*
+ * Add a WR to a connections's list of pending WRs.  This is a singly-linked
+ * list of sk_buffs operating as a FIFO.  The head is kept in wr_pending_head
+ * and the tail in wr_pending_tail.
+ */
+static inline void enqueue_wr(struct s3_conn *c3cn,
+			      struct sk_buff *skb)
+{
+	skb->sp = NULL;
+
+	/*
+	 * We want to take an extra reference since both us and the driver
+	 * need to free the packet before it's really freed. We know there's
+	 * just one user currently so we use atomic_set rather than skb_get
+	 * to avoid the atomic op.
+	 */
+	atomic_set(&skb->users, 2);
+
+	if (!c3cn->wr_pending_head)
+		c3cn->wr_pending_head = skb;
+	else
+		c3cn->wr_pending_tail->sp = (void *)skb;
+	c3cn->wr_pending_tail = skb;
+}
+
+static inline struct sk_buff *peek_wr(const struct s3_conn *c3cn)
+{
+	return c3cn->wr_pending_head;
+}
+
+static inline void free_wr_skb(struct sk_buff *skb)
+{
+	kfree_skb(skb);
+}
+
+static inline struct sk_buff *dequeue_wr(struct s3_conn *c3cn)
+{
+	struct sk_buff *skb = c3cn->wr_pending_head;
+
+	if (likely(skb)) {
+		/* Don't bother clearing the tail */
+		c3cn->wr_pending_head = (struct sk_buff *)skb->sp;
+		skb->sp = NULL;
+	}
+	return skb;
+}
+
+static void purge_wr_queue(struct s3_conn *c3cn)
+{
+	struct sk_buff *skb;
+	while ((skb = dequeue_wr(c3cn)) != NULL)
+		free_wr_skb(skb);
+}
+
+static inline void make_tx_data_wr(struct s3_conn *c3cn, struct sk_buff *skb,
+				   int len)
+{
+	struct tx_data_wr *req;
+
+	skb_reset_transport_header(skb);
+	req = (struct tx_data_wr *)__skb_push(skb, sizeof(*req));
+	req->wr_hi = htonl(V_WR_OP(FW_WROPCODE_OFLD_TX_DATA));
+	req->wr_lo = htonl(V_WR_TID(c3cn->tid));
+	req->sndseq = htonl(c3cn->snd_nxt);
+	/* len includes the length of any HW ULP additions */
+	req->len = htonl(len);
+	req->param = htonl(V_TX_PORT(c3cn->l2t->smt_idx));
+	/* V_TX_ULP_SUBMODE sets both the mode and submode */
+	req->flags = htonl(V_TX_ULP_SUBMODE(skb_ulp_mode(skb)) |
+			   V_TX_SHOVE((skb_peek(&c3cn->write_queue) ? 0 : 1)));
+
+	if (!c3cn_flag(c3cn, C3CN_TX_DATA_SENT)) {
+		req->flags |= htonl(V_TX_ACK_PAGES(2) | F_TX_INIT |
+				    V_TX_CPU_IDX(c3cn->qset));
+		/* Sendbuffer is in units of 32KB. */
+		req->param |= htonl(V_TX_SNDBUF(cxgb3_snd_win >> 15));
+		c3cn_set_flag(c3cn, C3CN_TX_DATA_SENT);
+	}
+}
+
+/**
+ * c3cn_push_tx_frames -- start transmit
+ * @c3cn: the offloaded connection
+ * @req_completion: request wr_ack or not
+ *
+ * Prepends TX_DATA_WR or CPL_CLOSE_CON_REQ headers to buffers waiting in a
+ * connection's send queue and sends them on to T3.  Must be called with the
+ * connection's lock held.  Returns the amount of send buffer space that was
+ * freed as a result of sending queued data to T3.
+ */
+static void arp_failure_discard(struct t3cdev *cdev, struct sk_buff *skb)
+{
+	kfree_skb(skb);
+}
+
+static int c3cn_push_tx_frames(struct s3_conn *c3cn, int req_completion)
+{
+	int total_size = 0;
+	struct sk_buff *skb;
+	struct t3cdev *cdev;
+	struct cxgb3i_sdev_data *cdata;
+
+	if (unlikely(c3cn->state == C3CN_STATE_CONNECTING ||
+		     c3cn->state == C3CN_STATE_CLOSE_WAIT_1 ||
+		     c3cn->state == C3CN_STATE_ABORTING)) {
+		c3cn_tx_debug("c3cn 0x%p, in closing state %u.\n",
+			      c3cn, c3cn->state);
+		return 0;
+	}
+
+	cdev = c3cn->cdev;
+	cdata = CXGB3_SDEV_DATA(cdev);
+
+	while (c3cn->wr_avail
+	       && (skb = skb_peek(&c3cn->write_queue)) != NULL) {
+		int len = skb->len;	/* length before skb_push */
+		int frags = skb_shinfo(skb)->nr_frags + (len != skb->data_len);
+		int wrs_needed = skb_wrs[frags];
+
+		if (wrs_needed > 1 && len + sizeof(struct tx_data_wr) <= wrlen)
+			wrs_needed = 1;
+
+		WARN_ON(frags >= SKB_WR_LIST_SIZE || wrs_needed < 1);
+
+		if (c3cn->wr_avail < wrs_needed) {
+			c3cn_tx_debug("c3cn 0x%p, skb len %u/%u, frag %u, "
+				      "wr %d < %u.\n",
+				      c3cn, skb->len, skb->datalen, frags,
+				      wrs_needed, c3cn->wr_avail);
+			break;
+		}
+
+		__skb_unlink(skb, &c3cn->write_queue);
+		skb->priority = CPL_PRIORITY_DATA;
+		skb->csum = wrs_needed;	/* remember this until the WR_ACK */
+		c3cn->wr_avail -= wrs_needed;
+		c3cn->wr_unacked += wrs_needed;
+		enqueue_wr(c3cn, skb);
+
+		if (likely(CXGB3_SKB_CB(skb)->flags & C3CB_FLAG_NEED_HDR)) {
+			len += ulp_extra_len(skb);
+			make_tx_data_wr(c3cn, skb, len);
+			c3cn->snd_nxt += len;
+			if ((req_completion
+			     && c3cn->wr_unacked == wrs_needed)
+			    || (CXGB3_SKB_CB(skb)->flags & C3CB_FLAG_COMPL)
+			    || c3cn->wr_unacked >= c3cn->wr_max / 2) {
+				struct work_request_hdr *wr = cplhdr(skb);
+
+				wr->wr_hi |= htonl(F_WR_COMPL);
+				c3cn->wr_unacked = 0;
+			}
+			CXGB3_SKB_CB(skb)->flags &= ~C3CB_FLAG_NEED_HDR;
+		}
+
+		total_size += skb->truesize;
+		set_arp_failure_handler(skb, arp_failure_discard);
+		l2t_send(cdev, skb, c3cn->l2t);
+	}
+	return total_size;
+}
+
+/*
+ * process_cpl_msg: -> host
+ * Top-level CPL message processing used by most CPL messages that
+ * pertain to connections.
+ */
+static inline void process_cpl_msg(void (*fn)(struct s3_conn *,
+					      struct sk_buff *),
+				   struct s3_conn *c3cn,
+				   struct sk_buff *skb)
+{
+	spin_lock_bh(&c3cn->lock);
+	fn(c3cn, skb);
+	spin_unlock_bh(&c3cn->lock);
+}
+
+/*
+ * process_cpl_msg_ref: -> host
+ * Similar to process_cpl_msg() but takes an extra connection reference around
+ * the call to the handler.  Should be used if the handler may drop a
+ * connection reference.
+ */
+static inline void process_cpl_msg_ref(void (*fn) (struct s3_conn *,
+						   struct sk_buff *),
+				       struct s3_conn *c3cn,
+				       struct sk_buff *skb)
+{
+	c3cn_hold(c3cn);
+	process_cpl_msg(fn, c3cn, skb);
+	c3cn_put(c3cn);
+}
+
+/*
+ * Process a CPL_ACT_ESTABLISH message: -> host
+ * Updates connection state from an active establish CPL message.  Runs with
+ * the connection lock held.
+ */
+
+static inline void s3_free_atid(struct t3cdev *cdev, unsigned int tid)
+{
+	struct s3_conn *c3cn = cxgb3_free_atid(cdev, tid);
+	if (c3cn)
+		c3cn_put(c3cn);
+}
+
+static void c3cn_established(struct s3_conn *c3cn, u32 snd_isn,
+			     unsigned int opt)
+{
+	c3cn_conn_debug("c3cn 0x%p, state %u.\n", c3cn, c3cn->state);
+
+	c3cn->write_seq = c3cn->snd_nxt = c3cn->snd_una = snd_isn;
+
+	/*
+	 * Causes the first RX_DATA_ACK to supply any Rx credits we couldn't
+	 * pass through opt0.
+	 */
+	if (cxgb3_rcv_win > (M_RCV_BUFSIZ << 10))
+		c3cn->rcv_wup -= cxgb3_rcv_win - (M_RCV_BUFSIZ << 10);
+
+	dst_confirm(c3cn->dst_cache);
+
+	smp_mb();
+
+	c3cn_set_state(c3cn, C3CN_STATE_ESTABLISHED);
+}
+
+static void process_act_establish(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	struct cpl_act_establish *req = cplhdr(skb);
+	u32 rcv_isn = ntohl(req->rcv_isn);	/* real RCV_ISN + 1 */
+
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	if (unlikely(c3cn->state != C3CN_STATE_CONNECTING))
+		cxgb3i_log_error("TID %u expected SYN_SENT, got EST., s %u\n",
+				 c3cn->tid, c3cn->state);
+
+	c3cn->copied_seq = c3cn->rcv_wup = c3cn->rcv_nxt = rcv_isn;
+	c3cn_established(c3cn, ntohl(req->snd_isn), ntohs(req->tcp_opt));
+
+	__kfree_skb(skb);
+
+	if (unlikely(c3cn_flag(c3cn, C3CN_ACTIVE_CLOSE_NEEDED)))
+		/* upper layer has requested closing */
+		send_abort_req(c3cn);
+	else if (c3cn_push_tx_frames(c3cn, 1))
+		cxgb3i_conn_tx_open(c3cn);
+}
+
+static int do_act_establish(struct t3cdev *cdev, struct sk_buff *skb,
+			    void *ctx)
+{
+	struct cpl_act_establish *req = cplhdr(skb);
+	unsigned int tid = GET_TID(req);
+	unsigned int atid = G_PASS_OPEN_TID(ntohl(req->tos_tid));
+	struct s3_conn *c3cn = ctx;
+	struct cxgb3i_sdev_data *cdata = CXGB3_SDEV_DATA(cdev);
+
+	c3cn_conn_debug("rcv, tid 0x%x, c3cn 0x%p, s %u, f 0x%lx.\n",
+			tid, c3cn, c3cn->state, c3cn->flags);
+
+	c3cn->tid = tid;
+	c3cn_hold(c3cn);
+	cxgb3_insert_tid(cdata->cdev, cdata->client, c3cn, tid);
+	s3_free_atid(cdev, atid);
+
+	c3cn->qset = G_QNUM(ntohl(skb->csum));
+
+	process_cpl_msg(process_act_establish, c3cn, skb);
+	return 0;
+}
+
+/*
+ * Process a CPL_ACT_OPEN_RPL message: -> host
+ * Handle active open failures.
+ */
+static int act_open_rpl_status_to_errno(int status)
+{
+	switch (status) {
+	case CPL_ERR_CONN_RESET:
+		return ECONNREFUSED;
+	case CPL_ERR_ARP_MISS:
+		return EHOSTUNREACH;
+	case CPL_ERR_CONN_TIMEDOUT:
+		return ETIMEDOUT;
+	case CPL_ERR_TCAM_FULL:
+		return ENOMEM;
+	case CPL_ERR_CONN_EXIST:
+		cxgb3i_log_error("ACTIVE_OPEN_RPL: 4-tuple in use\n");
+		return EADDRINUSE;
+	default:
+		return EIO;
+	}
+}
+
+static void act_open_retry_timer(unsigned long data)
+{
+	struct sk_buff *skb;
+	struct s3_conn *c3cn = (struct s3_conn *)data;
+
+	c3cn_conn_debug("c3cn 0x%p, state %u.\n", c3cn, c3cn->state);
+
+	spin_lock_bh(&c3cn->lock);
+	skb = alloc_skb(sizeof(struct cpl_act_open_req), GFP_ATOMIC);
+	if (!skb)
+		fail_act_open(c3cn, ENOMEM);
+	else {
+		skb->sk = (struct sock *)c3cn;
+		set_arp_failure_handler(skb, act_open_req_arp_failure);
+		make_act_open_req(c3cn, skb, c3cn->tid, c3cn->l2t);
+		l2t_send(c3cn->cdev, skb, c3cn->l2t);
+	}
+	spin_unlock_bh(&c3cn->lock);
+	c3cn_put(c3cn);
+}
+
+static void process_act_open_rpl(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	struct cpl_act_open_rpl *rpl = cplhdr(skb);
+
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	if (rpl->status == CPL_ERR_CONN_EXIST &&
+	    c3cn->retry_timer.function != act_open_retry_timer) {
+		c3cn->retry_timer.function = act_open_retry_timer;
+		if (!mod_timer(&c3cn->retry_timer, jiffies + HZ / 2))
+			c3cn_hold(c3cn);
+	} else
+		fail_act_open(c3cn, act_open_rpl_status_to_errno(rpl->status));
+	__kfree_skb(skb);
+}
+
+static int do_act_open_rpl(struct t3cdev *cdev, struct sk_buff *skb, void *ctx)
+{
+	struct s3_conn *c3cn = ctx;
+	struct cpl_act_open_rpl *rpl = cplhdr(skb);
+
+	c3cn_conn_debug("rcv, status 0x%x, c3cn 0x%p, s %u, f 0x%lx.\n",
+			rpl->status, c3cn, c3cn->state, c3cn->flags);
+
+	if (rpl->status != CPL_ERR_TCAM_FULL &&
+	    rpl->status != CPL_ERR_CONN_EXIST &&
+	    rpl->status != CPL_ERR_ARP_MISS)
+		cxgb3_queue_tid_release(cdev, GET_TID(rpl));
+
+	process_cpl_msg_ref(process_act_open_rpl, c3cn, skb);
+	return 0;
+}
+
+/*
+ * Process PEER_CLOSE CPL messages: -> host
+ * Handle peer FIN.
+ */
+static void process_peer_close(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	if (c3cn_flag(c3cn, C3CN_ABORT_RPL_PENDING))
+		goto out;
+
+	switch (c3cn->state) {
+	case C3CN_STATE_ESTABLISHED:
+		c3cn_set_state(c3cn, C3CN_STATE_PASSIVE_CLOSE);
+		break;
+	case C3CN_STATE_ACTIVE_CLOSE:
+		c3cn_set_state(c3cn, C3CN_STATE_CLOSE_WAIT_2);
+		break;
+	case C3CN_STATE_CLOSE_WAIT_1:
+		c3cn_closed(c3cn);
+		break;
+	case C3CN_STATE_ABORTING:
+		break;
+	default:
+		cxgb3i_log_error("%s: peer close, TID %u in bad state %u\n",
+				 c3cn->cdev->name, c3cn->tid, c3cn->state);
+	}
+
+	cxgb3i_conn_closing(c3cn);
+out:
+	__kfree_skb(skb);
+}
+
+static int do_peer_close(struct t3cdev *cdev, struct sk_buff *skb, void *ctx)
+{
+	struct s3_conn *c3cn = ctx;
+
+	c3cn_conn_debug("rcv, c3cn 0x%p, s %u, f 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+	process_cpl_msg_ref(process_peer_close, c3cn, skb);
+	return 0;
+}
+
+/*
+ * Process CLOSE_CONN_RPL CPL message: -> host
+ * Process a peer ACK to our FIN.
+ */
+static void process_close_con_rpl(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	struct cpl_close_con_rpl *rpl = cplhdr(skb);
+
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	c3cn->snd_una = ntohl(rpl->snd_nxt) - 1;	/* exclude FIN */
+
+	if (c3cn_flag(c3cn, C3CN_ABORT_RPL_PENDING))
+		goto out;
+
+	switch (c3cn->state) {
+	case C3CN_STATE_ACTIVE_CLOSE:
+		c3cn_set_state(c3cn, C3CN_STATE_CLOSE_WAIT_1);
+		break;
+	case C3CN_STATE_CLOSE_WAIT_1:
+	case C3CN_STATE_CLOSE_WAIT_2:
+		c3cn_closed(c3cn);
+		break;
+	case C3CN_STATE_ABORTING:
+		break;
+	default:
+		cxgb3i_log_error("%s: close_rpl, TID %u in bad state %u\n",
+				 c3cn->cdev->name, c3cn->tid, c3cn->state);
+	}
+
+out:
+	kfree_skb(skb);
+}
+
+static int do_close_con_rpl(struct t3cdev *cdev, struct sk_buff *skb,
+			    void *ctx)
+{
+	struct s3_conn *c3cn = ctx;
+
+	c3cn_conn_debug("rcv, c3cn 0x%p, s %u, f 0x%lx.\n",
+			 c3cn, c3cn->state, c3cn->flags);
+
+	process_cpl_msg_ref(process_close_con_rpl, c3cn, skb);
+	return 0;
+}
+
+/*
+ * Process ABORT_REQ_RSS CPL message: -> host
+ * Process abort requests.  If we are waiting for an ABORT_RPL we ignore this
+ * request except that we need to reply to it.
+ */
+
+static int abort_status_to_errno(struct s3_conn *c3cn, int abort_reason,
+				 int *need_rst)
+{
+	switch (abort_reason) {
+	case CPL_ERR_BAD_SYN: /* fall through */
+	case CPL_ERR_CONN_RESET:
+		return c3cn->state > C3CN_STATE_ESTABLISHED ?
+			EPIPE : ECONNRESET;
+	case CPL_ERR_XMIT_TIMEDOUT:
+	case CPL_ERR_PERSIST_TIMEDOUT:
+	case CPL_ERR_FINWAIT2_TIMEDOUT:
+	case CPL_ERR_KEEPALIVE_TIMEDOUT:
+		return ETIMEDOUT;
+	default:
+		return EIO;
+	}
+}
+
+static void process_abort_req(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	int rst_status = CPL_ABORT_NO_RST;
+	const struct cpl_abort_req_rss *req = cplhdr(skb);
+
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	if (!c3cn_flag(c3cn, C3CN_ABORT_REQ_RCVD)) {
+		c3cn_set_flag(c3cn, C3CN_ABORT_REQ_RCVD);
+		c3cn_set_state(c3cn, C3CN_STATE_ABORTING);
+		__kfree_skb(skb);
+		return;
+	}
+
+	c3cn_clear_flag(c3cn, C3CN_ABORT_REQ_RCVD);
+	send_abort_rpl(c3cn, rst_status);
+
+	if (!c3cn_flag(c3cn, C3CN_ABORT_RPL_PENDING)) {
+		c3cn->err =
+		    abort_status_to_errno(c3cn, req->status, &rst_status);
+		c3cn_closed(c3cn);
+	}
+}
+
+static int do_abort_req(struct t3cdev *cdev, struct sk_buff *skb, void *ctx)
+{
+	const struct cpl_abort_req_rss *req = cplhdr(skb);
+	struct s3_conn *c3cn = ctx;
+
+	c3cn_conn_debug("rcv, c3cn 0x%p, s 0x%x, f 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	if (req->status == CPL_ERR_RTX_NEG_ADVICE ||
+	    req->status == CPL_ERR_PERSIST_NEG_ADVICE) {
+		__kfree_skb(skb);
+		return 0;
+	}
+
+	process_cpl_msg_ref(process_abort_req, c3cn, skb);
+	return 0;
+}
+
+/*
+ * Process ABORT_RPL_RSS CPL message: -> host
+ * Process abort replies.  We only process these messages if we anticipate
+ * them as the coordination between SW and HW in this area is somewhat lacking
+ * and sometimes we get ABORT_RPLs after we are done with the connection that
+ * originated the ABORT_REQ.
+ */
+static void process_abort_rpl(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+
+	if (c3cn_flag(c3cn, C3CN_ABORT_RPL_PENDING)) {
+		if (!c3cn_flag(c3cn, C3CN_ABORT_RPL_RCVD))
+			c3cn_set_flag(c3cn, C3CN_ABORT_RPL_RCVD);
+		else {
+			c3cn_clear_flag(c3cn, C3CN_ABORT_RPL_RCVD);
+			c3cn_clear_flag(c3cn, C3CN_ABORT_RPL_PENDING);
+			if (c3cn_flag(c3cn, C3CN_ABORT_REQ_RCVD))
+				cxgb3i_log_error("%s tid %u, ABORT_RPL_RSS\n",
+						 c3cn->cdev->name, c3cn->tid);
+			c3cn_closed(c3cn);
+		}
+	}
+	__kfree_skb(skb);
+}
+
+static int do_abort_rpl(struct t3cdev *cdev, struct sk_buff *skb, void *ctx)
+{
+	struct cpl_abort_rpl_rss *rpl = cplhdr(skb);
+	struct s3_conn *c3cn = ctx;
+
+	c3cn_conn_debug("rcv, status 0x%x, c3cn 0x%p, s %u, 0x%lx.\n",
+			rpl->status, c3cn, c3cn ? c3cn->state : 0,
+			c3cn ? c3cn->flags : 0UL);
+
+	/*
+	 * Ignore replies to post-close aborts indicating that the abort was
+	 * requested too late.  These connections are terminated when we get
+	 * PEER_CLOSE or CLOSE_CON_RPL and by the time the abort_rpl_rss
+	 * arrives the TID is either no longer used or it has been recycled.
+	 */
+	if (rpl->status == CPL_ERR_ABORT_FAILED)
+		goto discard;
+
+	/*
+	 * Sometimes we've already closed the connection, e.g., a post-close
+	 * abort races with ABORT_REQ_RSS, the latter frees the connection
+	 * expecting the ABORT_REQ will fail with CPL_ERR_ABORT_FAILED,
+	 * but FW turns the ABORT_REQ into a regular one and so we get
+	 * ABORT_RPL_RSS with status 0 and no connection.
+	 */
+	if (!c3cn)
+		goto discard;
+
+	process_cpl_msg_ref(process_abort_rpl, c3cn, skb);
+	return 0;
+
+discard:
+	__kfree_skb(skb);
+	return 0;
+}
+
+/*
+ * Process RX_ISCSI_HDR CPL message: -> host
+ * Handle received PDUs, the payload could be DDP'ed. If not, the payload
+ * follow after the bhs.
+ */
+static void process_rx_iscsi_hdr(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	struct cpl_iscsi_hdr *hdr_cpl = cplhdr(skb);
+	struct cpl_iscsi_hdr_norss data_cpl;
+	struct cpl_rx_data_ddp_norss ddp_cpl;
+	unsigned int hdr_len, data_len, status;
+	unsigned int len;
+	int err;
+
+	if (unlikely(c3cn->state >= C3CN_STATE_PASSIVE_CLOSE)) {
+		if (c3cn->state != C3CN_STATE_ABORTING)
+			send_abort_req(c3cn);
+		__kfree_skb(skb);
+		return;
+	}
+
+	CXGB3_SKB_CB(skb)->seq = ntohl(hdr_cpl->seq);
+	CXGB3_SKB_CB(skb)->flags = 0;
+
+	skb_reset_transport_header(skb);
+	__skb_pull(skb, sizeof(struct cpl_iscsi_hdr));
+
+	len = hdr_len = ntohs(hdr_cpl->len);
+	/* msg coalesce is off or not enough data received */
+	if (skb->len <= hdr_len) {
+		cxgb3i_log_error("%s: TID %u, ISCSI_HDR, skb len %u < %u.\n",
+				 c3cn->cdev->name, c3cn->tid,
+				 skb->len, hdr_len);
+		goto abort_conn;
+	}
+
+	err = skb_copy_bits(skb, skb->len - sizeof(ddp_cpl), &ddp_cpl,
+			    sizeof(ddp_cpl));
+	if (err < 0)
+		goto abort_conn;
+
+	skb_ulp_mode(skb) = ULP2_FLAG_DATA_READY;
+	skb_ulp_pdulen(skb) = ntohs(ddp_cpl.len);
+	skb_ulp_ddigest(skb) = ntohl(ddp_cpl.ulp_crc);
+	status = ntohl(ddp_cpl.ddp_status);
+
+	c3cn_rx_debug("rx skb 0x%p, len %u, pdulen %u, ddp status 0x%x.\n",
+		      skb, skb->len, skb_ulp_pdulen(skb), status);
+
+	if (status & (1 << RX_DDP_STATUS_HCRC_SHIFT))
+		skb_ulp_mode(skb) |= ULP2_FLAG_HCRC_ERROR;
+	if (status & (1 << RX_DDP_STATUS_DCRC_SHIFT))
+		skb_ulp_mode(skb) |= ULP2_FLAG_DCRC_ERROR;
+	if (status & (1 << RX_DDP_STATUS_PAD_SHIFT))
+		skb_ulp_mode(skb) |= ULP2_FLAG_PAD_ERROR;
+
+	if (skb->len > (hdr_len + sizeof(ddp_cpl))) {
+		err = skb_copy_bits(skb, hdr_len, &data_cpl, sizeof(data_cpl));
+		if (err < 0)
+			goto abort_conn;
+		data_len = ntohs(data_cpl.len);
+		len += sizeof(data_cpl) + data_len;
+	} else if (status & (1 << RX_DDP_STATUS_DDP_SHIFT))
+		skb_ulp_mode(skb) |= ULP2_FLAG_DATA_DDPED;
+
+	c3cn->rcv_nxt = ntohl(ddp_cpl.seq) + skb_ulp_pdulen(skb);
+	__pskb_trim(skb, len);
+	__skb_queue_tail(&c3cn->receive_queue, skb);
+	cxgb3i_conn_pdu_ready(c3cn);
+
+	return;
+
+abort_conn:
+	send_abort_req(c3cn);
+	__kfree_skb(skb);
+}
+
+static int do_iscsi_hdr(struct t3cdev *t3dev, struct sk_buff *skb, void *ctx)
+{
+	struct s3_conn *c3cn = ctx;
+
+	process_cpl_msg(process_rx_iscsi_hdr, c3cn, skb);
+	return 0;
+}
+
+/*
+ * Process TX_DATA_ACK CPL messages: -> host
+ * Process an acknowledgment of WR completion.  Advance snd_una and send the
+ * next batch of work requests from the write queue.
+ */
+static void process_wr_ack(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	struct cpl_wr_ack *hdr = cplhdr(skb);
+	unsigned int credits = ntohs(hdr->credits);
+	u32 snd_una = ntohl(hdr->snd_una);
+
+	c3cn->wr_avail += credits;
+	if (c3cn->wr_unacked > c3cn->wr_max - c3cn->wr_avail)
+		c3cn->wr_unacked = c3cn->wr_max - c3cn->wr_avail;
+
+	while (credits) {
+		struct sk_buff *p = peek_wr(c3cn);
+
+		if (unlikely(!p)) {
+			cxgb3i_log_error("%u WR_ACK credits for TID %u with "
+					 "nothing pending, state %u\n",
+					 credits, c3cn->tid, c3cn->state);
+			break;
+		}
+		if (unlikely(credits < p->csum)) {
+			p->csum -= credits;
+			break;
+		} else {
+			dequeue_wr(c3cn);
+			credits -= p->csum;
+			free_wr_skb(p);
+		}
+	}
+
+	if (unlikely(before(snd_una, c3cn->snd_una)))
+		goto out_free;
+
+	if (c3cn->snd_una != snd_una) {
+		c3cn->snd_una = snd_una;
+		dst_confirm(c3cn->dst_cache);
+	}
+
+	if (skb_queue_len(&c3cn->write_queue) && c3cn_push_tx_frames(c3cn, 0))
+		cxgb3i_conn_tx_open(c3cn);
+out_free:
+	__kfree_skb(skb);
+}
+
+static int do_wr_ack(struct t3cdev *cdev, struct sk_buff *skb, void *ctx)
+{
+	struct s3_conn *c3cn = ctx;
+
+	process_cpl_msg(process_wr_ack, c3cn, skb);
+	return 0;
+}
+
+/*
+ * for each connection, pre-allocate skbs needed for close/abort requests. So
+ * that we can service the request right away.
+ */
+static void c3cn_free_cpl_skbs(struct s3_conn *c3cn)
+{
+	if (c3cn->cpl_close)
+		kfree_skb(c3cn->cpl_close);
+	if (c3cn->cpl_abort_req)
+		kfree_skb(c3cn->cpl_abort_req);
+	if (c3cn->cpl_abort_rpl)
+		kfree_skb(c3cn->cpl_abort_rpl);
+}
+
+static int c3cn_alloc_cpl_skbs(struct s3_conn *c3cn)
+{
+	c3cn->cpl_close = alloc_skb(sizeof(struct cpl_close_con_req),
+				   GFP_KERNEL);
+	if (!c3cn->cpl_close)
+		return -ENOMEM;
+	skb_put(c3cn->cpl_close, sizeof(struct cpl_close_con_req));
+
+	c3cn->cpl_abort_req = alloc_skb(sizeof(struct cpl_abort_req),
+					GFP_KERNEL);
+	if (!c3cn->cpl_abort_req)
+		goto free_cpl_skbs;
+	skb_put(c3cn->cpl_abort_req, sizeof(struct cpl_abort_req));
+
+	c3cn->cpl_abort_rpl = alloc_skb(sizeof(struct cpl_abort_rpl),
+					GFP_KERNEL);
+	if (!c3cn->cpl_abort_rpl)
+		goto free_cpl_skbs;
+	skb_put(c3cn->cpl_abort_rpl, sizeof(struct cpl_abort_rpl));
+
+	return 0;
+
+free_cpl_skbs:
+	c3cn_free_cpl_skbs(c3cn);
+	return -ENOMEM;
+}
+
+/**
+ * c3cn_release_offload_resources - release offload resource
+ * @c3cn: the offloaded iscsi tcp connection.
+ * Release resources held by an offload connection (TID, L2T entry, etc.)
+ */
+static void c3cn_release_offload_resources(struct s3_conn *c3cn)
+{
+	struct t3cdev *cdev = c3cn->cdev;
+	unsigned int tid = c3cn->tid;
+
+	if (!cdev)
+		return;
+
+	c3cn->qset = 0;
+
+	c3cn_free_cpl_skbs(c3cn);
+
+	if (c3cn->wr_avail != c3cn->wr_max) {
+		purge_wr_queue(c3cn);
+		reset_wr_list(c3cn);
+	}
+
+	if (c3cn->l2t) {
+		l2t_release(L2DATA(cdev), c3cn->l2t);
+		c3cn->l2t = NULL;
+	}
+
+	if (c3cn->state == C3CN_STATE_CONNECTING) /* we have ATID */
+		s3_free_atid(cdev, tid);
+	else {		/* we have TID */
+		cxgb3_remove_tid(cdev, (void *)c3cn, tid);
+		c3cn_put(c3cn);
+	}
+
+	c3cn->cdev = NULL;
+}
+
+/**
+ * cxgb3i_c3cn_create - allocate and initialize an s3_conn structure
+ * returns the s3_conn structure allocated.
+ */
+struct s3_conn *cxgb3i_c3cn_create(void)
+{
+	struct s3_conn *c3cn;
+
+	c3cn = kzalloc(sizeof(*c3cn), GFP_KERNEL);
+	if (!c3cn)
+		return NULL;
+
+	/* pre-allocate close/abort cpl, so we don't need to wait for memory
+	   when close/abort is requested. */
+	if (c3cn_alloc_cpl_skbs(c3cn) < 0)
+		goto free_c3cn;
+
+	c3cn_conn_debug("alloc c3cn 0x%p.\n", c3cn);
+
+	c3cn->flags = 0;
+	spin_lock_init(&c3cn->lock);
+	atomic_set(&c3cn->refcnt, 1);
+	skb_queue_head_init(&c3cn->receive_queue);
+	skb_queue_head_init(&c3cn->write_queue);
+	setup_timer(&c3cn->retry_timer, NULL, (unsigned long)c3cn);
+	rwlock_init(&c3cn->callback_lock);
+
+	return c3cn;
+
+free_c3cn:
+	kfree(c3cn);
+	return NULL;
+}
+
+static void c3cn_active_close(struct s3_conn *c3cn)
+{
+	int data_lost;
+	int close_req = 0;
+
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			 c3cn, c3cn->state, c3cn->flags);
+
+	dst_confirm(c3cn->dst_cache);
+
+	c3cn_hold(c3cn);
+	spin_lock_bh(&c3cn->lock);
+
+	data_lost = skb_queue_len(&c3cn->receive_queue);
+	__skb_queue_purge(&c3cn->receive_queue);
+
+	switch (c3cn->state) {
+	case C3CN_STATE_CLOSED:
+	case C3CN_STATE_ACTIVE_CLOSE:
+	case C3CN_STATE_CLOSE_WAIT_1:
+	case C3CN_STATE_CLOSE_WAIT_2:
+	case C3CN_STATE_ABORTING:
+		/* nothing need to be done */
+		break;
+	case C3CN_STATE_CONNECTING:
+		/* defer until cpl_act_open_rpl or cpl_act_establish */
+		c3cn_set_flag(c3cn, C3CN_ACTIVE_CLOSE_NEEDED);
+		break;
+	case C3CN_STATE_ESTABLISHED:
+		close_req = 1;
+		c3cn_set_state(c3cn, C3CN_STATE_ACTIVE_CLOSE);
+		break;
+	case C3CN_STATE_PASSIVE_CLOSE:
+		close_req = 1;
+		c3cn_set_state(c3cn, C3CN_STATE_CLOSE_WAIT_2);
+		break;
+	}
+
+	if (close_req) {
+		if (data_lost)
+			/* Unread data was tossed, zap the connection. */
+			send_abort_req(c3cn);
+		else
+			send_close_req(c3cn);
+	}
+
+	spin_unlock_bh(&c3cn->lock);
+	c3cn_put(c3cn);
+}
+
+/**
+ * cxgb3i_c3cn_release - close and release an iscsi tcp connection and any
+ * 	resource held
+ * @c3cn: the iscsi tcp connection
+ */
+void cxgb3i_c3cn_release(struct s3_conn *c3cn)
+{
+	c3cn_conn_debug("c3cn 0x%p, s %u, f 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+	if (likely(c3cn->state != C3CN_STATE_CONNECTING))
+		c3cn_active_close(c3cn);
+	else
+		c3cn_set_flag(c3cn, C3CN_ACTIVE_CLOSE_NEEDED);
+	c3cn_put(c3cn);
+}
+
+static int is_cxgb3_dev(struct net_device *dev)
+{
+	struct cxgb3i_sdev_data *cdata;
+
+	write_lock(&cdata_rwlock);
+	list_for_each_entry(cdata, &cdata_list, list) {
+		struct adap_ports *ports = &cdata->ports;
+		int i;
+
+		for (i = 0; i < ports->nports; i++)
+			if (dev == ports->lldevs[i]) {
+				write_unlock(&cdata_rwlock);
+				return 1;
+			}
+	}
+	write_unlock(&cdata_rwlock);
+	return 0;
+}
+
+/**
+ * cxgb3_egress_dev - return the cxgb3 egress device
+ * @root_dev: the root device anchoring the search
+ * @c3cn: the connection used to determine egress port in bonding mode
+ * @context: in bonding mode, indicates a connection set up or failover
+ *
+ * Return egress device or NULL if the egress device isn't one of our ports.
+ */
+static struct net_device *cxgb3_egress_dev(struct net_device *root_dev,
+					   struct s3_conn *c3cn,
+					   int context)
+{
+	while (root_dev) {
+		if (root_dev->priv_flags & IFF_802_1Q_VLAN)
+			root_dev = vlan_dev_real_dev(root_dev);
+		else if (is_cxgb3_dev(root_dev))
+			return root_dev;
+		else
+			return NULL;
+	}
+	return NULL;
+}
+
+static struct rtable *find_route(__be32 saddr, __be32 daddr,
+				 __be16 sport, __be16 dport)
+{
+	struct rtable *rt;
+	struct flowi fl = {
+		.oif = 0,
+		.nl_u = {
+			 .ip4_u = {
+				   .daddr = daddr,
+				   .saddr = saddr,
+				   .tos = 0 } },
+		.proto = IPPROTO_TCP,
+		.uli_u = {
+			  .ports = {
+				    .sport = sport,
+				    .dport = dport } } };
+
+	if (ip_route_output_flow(&init_net, &rt, &fl, NULL, 0))
+		return NULL;
+	return rt;
+}
+
+/*
+ * Assign offload parameters to some connection fields.
+ */
+static void init_offload_conn(struct s3_conn *c3cn,
+			      struct t3cdev *cdev,
+			      struct dst_entry *dst)
+{
+	BUG_ON(c3cn->cdev != cdev);
+	c3cn->wr_max = c3cn->wr_avail = T3C_DATA(cdev)->max_wrs;
+	c3cn->wr_unacked = 0;
+	c3cn->mss_idx = select_mss(c3cn, dst_mtu(dst));
+
+	reset_wr_list(c3cn);
+}
+
+static int initiate_act_open(struct s3_conn *c3cn, struct net_device *dev)
+{
+	struct cxgb3i_sdev_data *cdata = NDEV2CDATA(dev);
+	struct t3cdev *cdev = cdata->cdev;
+	struct dst_entry *dst = c3cn->dst_cache;
+	struct sk_buff *skb;
+
+	c3cn_conn_debug("c3cn 0x%p, state %u, flag 0x%lx.\n",
+			c3cn, c3cn->state, c3cn->flags);
+	/*
+	 * Initialize connection data.  Note that the flags and ULP mode are
+	 * initialized higher up ...
+	 */
+	c3cn->dev = dev;
+	c3cn->cdev = cdev;
+	c3cn->tid = cxgb3_alloc_atid(cdev, cdata->client, c3cn);
+	if (c3cn->tid < 0)
+		goto out_err;
+
+	c3cn->qset = 0;
+	c3cn->l2t = t3_l2t_get(cdev, dst->neighbour, dev);
+	if (!c3cn->l2t)
+		goto free_tid;
+
+	skb = alloc_skb(sizeof(struct cpl_act_open_req), GFP_KERNEL);
+	if (!skb)
+		goto free_l2t;
+
+	skb->sk = (struct sock *)c3cn;
+	set_arp_failure_handler(skb, act_open_req_arp_failure);
+
+	c3cn_hold(c3cn);
+
+	init_offload_conn(c3cn, cdev, dst);
+	c3cn->err = 0;
+
+	make_act_open_req(c3cn, skb, c3cn->tid, c3cn->l2t);
+	l2t_send(cdev, skb, c3cn->l2t);
+	return 0;
+
+free_l2t:
+	l2t_release(L2DATA(cdev), c3cn->l2t);
+free_tid:
+	s3_free_atid(cdev, c3cn->tid);
+	c3cn->tid = 0;
+out_err:
+	return -1;
+}
+
+
+/**
+ * cxgb3i_c3cn_connect - initiates an iscsi tcp connection to a given address
+ * @c3cn: the iscsi tcp connection
+ * @usin: destination address
+ *
+ * return 0 if active open request is sent, < 0 otherwise.
+ */
+int cxgb3i_c3cn_connect(struct s3_conn *c3cn, struct sockaddr_in *usin)
+{
+	struct rtable *rt;
+	struct net_device *dev;
+	struct cxgb3i_sdev_data *cdata;
+	struct t3cdev *cdev;
+	__be32 sipv4;
+	int err;
+
+	if (usin->sin_family != AF_INET)
+		return -EAFNOSUPPORT;
+
+	c3cn->daddr.sin_port = usin->sin_port;
+	c3cn->daddr.sin_addr.s_addr = usin->sin_addr.s_addr;
+
+	rt = find_route(c3cn->saddr.sin_addr.s_addr,
+			c3cn->daddr.sin_addr.s_addr,
+			c3cn->saddr.sin_port,
+			c3cn->daddr.sin_port);
+	if (rt == NULL) {
+		c3cn_conn_debug("NO route to 0x%x, port %u.\n",
+				c3cn->daddr.sin_addr.s_addr,
+				ntohs(c3cn->daddr.sin_port));
+		return -ENETUNREACH;
+	}
+
+	if (rt->rt_flags & (RTCF_MULTICAST | RTCF_BROADCAST)) {
+		c3cn_conn_debug("multi-cast route to 0x%x, port %u.\n",
+				c3cn->daddr.sin_addr.s_addr,
+				ntohs(c3cn->daddr.sin_port));
+		ip_rt_put(rt);
+		return -ENETUNREACH;
+	}
+
+	if (!c3cn->saddr.sin_addr.s_addr)
+		c3cn->saddr.sin_addr.s_addr = rt->rt_src;
+
+	/* now commit destination to connection */
+	c3cn->dst_cache = &rt->u.dst;
+
+	/* try to establish an offloaded connection */
+	dev = cxgb3_egress_dev(c3cn->dst_cache->dev, c3cn, 0);
+	if (dev == NULL) {
+		c3cn_conn_debug("c3cn 0x%p, egress dev NULL.\n", c3cn);
+		return -ENETUNREACH;
+	}
+	cdata = NDEV2CDATA(dev);
+	cdev = cdata->cdev;
+
+	/* get a source port if one hasn't been provided */
+	err = c3cn_get_port(c3cn, cdata);
+	if (err)
+		return err;
+
+	c3cn_conn_debug("c3cn 0x%p get port %u.\n",
+			c3cn, ntohs(c3cn->saddr.sin_port));
+
+	sipv4 = cxgb3i_get_private_ipv4addr(dev);
+	if (!sipv4) {
+		c3cn_conn_debug("c3cn 0x%p, iscsi ip not configured.\n", c3cn);
+		sipv4 = c3cn->saddr.sin_addr.s_addr;
+		cxgb3i_set_private_ipv4addr(dev, sipv4);
+	} else
+		c3cn->saddr.sin_addr.s_addr = sipv4;
+
+	c3cn_conn_debug("c3cn 0x%p, %u.%u.%u.%u,%u-%u.%u.%u.%u,%u SYN_SENT.\n",
+			c3cn, NIPQUAD(c3cn->saddr.sin_addr.s_addr),
+			ntohs(c3cn->saddr.sin_port),
+			NIPQUAD(c3cn->daddr.sin_addr.s_addr),
+			ntohs(c3cn->daddr.sin_port));
+
+	c3cn_set_state(c3cn, C3CN_STATE_CONNECTING);
+	if (!initiate_act_open(c3cn, dev))
+		return 0;
+
+	/*
+	 * If we get here, we don't have an offload connection so simply
+	 * return a failure.
+	 */
+	err = -ENOTSUPP;
+
+	/*
+	 * This trashes the connection and releases the local port,
+	 * if necessary.
+	 */
+	c3cn_conn_debug("c3cn 0x%p -> CLOSED.\n", c3cn);
+	c3cn_set_state(c3cn, C3CN_STATE_CLOSED);
+	ip_rt_put(rt);
+	c3cn_put_port(c3cn);
+	c3cn->daddr.sin_port = 0;
+	return err;
+}
+
+/**
+ * cxgb3i_c3cn_rx_credits - ack received tcp data.
+ * @c3cn: iscsi tcp connection
+ * @copied: # of bytes processed
+ *
+ * Called after some received data has been read.  It returns RX credits
+ * to the HW for the amount of data processed.
+ */
+void cxgb3i_c3cn_rx_credits(struct s3_conn *c3cn, int copied)
+{
+	struct t3cdev *cdev;
+	int must_send;
+	u32 credits, dack = 0;
+
+	if (c3cn->state != C3CN_STATE_ESTABLISHED)
+		return;
+
+	credits = c3cn->copied_seq - c3cn->rcv_wup;
+	if (unlikely(!credits))
+		return;
+
+	cdev = c3cn->cdev;
+
+	if (unlikely(cxgb3_rx_credit_thres == 0))
+		return;
+
+	dack = F_RX_DACK_CHANGE | V_RX_DACK_MODE(1);
+
+	/*
+	 * For coalescing to work effectively ensure the receive window has
+	 * at least 16KB left.
+	 */
+	must_send = credits + 16384 >= cxgb3_rcv_win;
+
+	if (must_send || credits >= cxgb3_rx_credit_thres)
+		c3cn->rcv_wup += send_rx_credits(c3cn, credits, dack);
+}
+
+/**
+ * cxgb3i_c3cn_send_pdus - send the skbs containing iscsi pdus
+ * @c3cn: iscsi tcp connection
+ * @skb: skb contains the iscsi pdu
+ *
+ * Add a list of skbs to a connection send queue. The skbs must comply with
+ * the max size limit of the device and have a headroom of at least
+ * TX_HEADER_LEN bytes.
+ * Return # of bytes queued.
+ */
+int cxgb3i_c3cn_send_pdus(struct s3_conn *c3cn, struct sk_buff *skb)
+{
+	struct sk_buff *next;
+	int err, copied = 0;
+
+	spin_lock_bh(&c3cn->lock);
+
+	if (c3cn->state != C3CN_STATE_ESTABLISHED) {
+		c3cn_tx_debug("c3cn 0x%p, not in est. state %u.\n",
+			      c3cn, c3cn->state);
+		err = -EAGAIN;
+		goto out_err;
+	}
+
+	err = -EPIPE;
+	if (c3cn->err) {
+		c3cn_tx_debug("c3cn 0x%p, err %d.\n", c3cn, c3cn->err);
+		goto out_err;
+	}
+
+	while (skb) {
+		int frags = skb_shinfo(skb)->nr_frags +
+				(skb->len != skb->data_len);
+
+		if (unlikely(skb_headroom(skb) < TX_HEADER_LEN)) {
+			c3cn_tx_debug("c3cn 0x%p, skb head.\n", c3cn);
+			err = -EINVAL;
+			goto out_err;
+		}
+
+		if (frags >= SKB_WR_LIST_SIZE) {
+			cxgb3i_log_error("c3cn 0x%p, tx frags %d, len %u,%u.\n",
+					 c3cn, skb_shinfo(skb)->nr_frags,
+					 skb->len, skb->data_len);
+			err = -EINVAL;
+			goto out_err;
+		}
+
+		next = skb->next;
+		skb->next = NULL;
+		skb_entail(c3cn, skb, C3CB_FLAG_NO_APPEND | C3CB_FLAG_NEED_HDR);
+		copied += skb->len;
+		c3cn->write_seq += skb->len + ulp_extra_len(skb);
+		skb = next;
+	}
+done:
+	if (likely(skb_queue_len(&c3cn->write_queue)))
+		c3cn_push_tx_frames(c3cn, 1);
+	spin_unlock_bh(&c3cn->lock);
+	return copied;
+
+out_err:
+	if (copied == 0 && err == -EPIPE)
+		copied = c3cn->err ? c3cn->err : -EPIPE;
+	goto done;
+}
+
+static void sdev_data_cleanup(struct cxgb3i_sdev_data *cdata)
+{
+	struct adap_ports *ports = &cdata->ports;
+	int i;
+
+	for (i = 0; i < ports->nports; i++)
+		NDEV2CDATA(ports->lldevs[i]) = NULL;
+	cxgb3i_free_big_mem(cdata);
+}
+
+void cxgb3i_sdev_cleanup(void)
+{
+	struct cxgb3i_sdev_data *cdata;
+
+	write_lock(&cdata_rwlock);
+	list_for_each_entry(cdata, &cdata_list, list) {
+		list_del(&cdata->list);
+		sdev_data_cleanup(cdata);
+	}
+	write_unlock(&cdata_rwlock);
+}
+
+int cxgb3i_sdev_init(cxgb3_cpl_handler_func *cpl_handlers)
+{
+	cpl_handlers[CPL_ACT_ESTABLISH] = do_act_establish;
+	cpl_handlers[CPL_ACT_OPEN_RPL] = do_act_open_rpl;
+	cpl_handlers[CPL_PEER_CLOSE] = do_peer_close;
+	cpl_handlers[CPL_ABORT_REQ_RSS] = do_abort_req;
+	cpl_handlers[CPL_ABORT_RPL_RSS] = do_abort_rpl;
+	cpl_handlers[CPL_CLOSE_CON_RPL] = do_close_con_rpl;
+	cpl_handlers[CPL_TX_DMA_ACK] = do_wr_ack;
+	cpl_handlers[CPL_ISCSI_HDR] = do_iscsi_hdr;
+
+	if (cxgb3_max_connect > CXGB3I_MAX_CONN)
+		cxgb3_max_connect = CXGB3I_MAX_CONN;
+	return 0;
+}
+
+/**
+ * cxgb3i_sdev_add - allocate and initialize resources for each adapter found
+ * @cdev:	t3cdev adapter
+ * @client:	cxgb3 driver client
+ */
+void cxgb3i_sdev_add(struct t3cdev *cdev, struct cxgb3_client *client)
+{
+	struct cxgb3i_sdev_data *cdata;
+	struct ofld_page_info rx_page_info;
+	unsigned int wr_len;
+	int mapsize = DIV_ROUND_UP(cxgb3_max_connect,
+				   8 * sizeof(unsigned long));
+	int i;
+
+	cdata =  cxgb3i_alloc_big_mem(sizeof(*cdata) + mapsize, GFP_KERNEL);
+	if (!cdata)
+		return;
+
+	if (cdev->ctl(cdev, GET_WR_LEN, &wr_len) < 0 ||
+	    cdev->ctl(cdev, GET_PORTS, &cdata->ports) < 0 ||
+	    cdev->ctl(cdev, GET_RX_PAGE_INFO, &rx_page_info) < 0)
+		goto free_cdata;
+
+	s3_init_wr_tab(wr_len);
+
+	INIT_LIST_HEAD(&cdata->list);
+	cdata->cdev = cdev;
+	cdata->client = client;
+
+	for (i = 0; i < cdata->ports.nports; i++)
+		NDEV2CDATA(cdata->ports.lldevs[i]) = cdata;
+
+	write_lock(&cdata_rwlock);
+	list_add_tail(&cdata->list, &cdata_list);
+	write_unlock(&cdata_rwlock);
+
+	return;
+
+free_cdata:
+	cxgb3i_free_big_mem(cdata);
+}
+
+/**
+ * cxgb3i_sdev_remove - free the allocated resources for the adapter
+ * @cdev:	t3cdev adapter
+ */
+void cxgb3i_sdev_remove(struct t3cdev *cdev)
+{
+	struct cxgb3i_sdev_data *cdata = CXGB3_SDEV_DATA(cdev);
+
+	write_lock(&cdata_rwlock);
+	list_del(&cdata->list);
+	write_unlock(&cdata_rwlock);
+
+	sdev_data_cleanup(cdata);
+}
diff --git a/drivers/scsi/cxgb3i/cxgb3i_offload.h b/drivers/scsi/cxgb3i/cxgb3i_offload.h
new file mode 100644
index 0000000..5b93d62
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_offload.h
@@ -0,0 +1,231 @@
+/*
+ * cxgb3i_offload.h: Chelsio S3xx iscsi offloaded tcp connection management
+ *
+ * Copyright (C) 2003-2008 Chelsio Communications.  All rights reserved.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the LICENSE file included in this
+ * release for licensing terms and conditions.
+ *
+ * Written by:	Dimitris Michailidis (dm@chelsio.com)
+ *		Karen Xie (kxie@chelsio.com)
+ */
+
+#ifndef _CXGB3I_OFFLOAD_H
+#define _CXGB3I_OFFLOAD_H
+
+#include <linux/skbuff.h>
+#include <net/tcp.h>
+
+#include "common.h"
+#include "adapter.h"
+#include "t3cdev.h"
+#include "cxgb3_offload.h"
+
+#define cxgb3i_log_error(fmt...) printk(KERN_ERR "cxgb3i: ERR! " fmt)
+#define cxgb3i_log_warn(fmt...)	 printk(KERN_WARNING "cxgb3i: WARN! " fmt)
+#define cxgb3i_log_info(fmt...)  printk(KERN_INFO "cxgb3i: " fmt)
+#define cxgb3i_log_debug(fmt, args...) \
+	printk(KERN_INFO "cxgb3i: %s - " fmt, __func__ , ## args)
+
+/**
+ * struct s3_conn - an iscsi tcp connection structure
+ *
+ * @dev:	net device of with connection
+ * @cdev:	adapter t3cdev for net device
+ * @flags:	see c3cn_flags below
+ * @tid:	connection id assigned by the h/w
+ * @qset:	queue set used by connection
+ * @mss_idx:	Maximum Segment Size table index
+ * @l2t:	ARP resolution entry for offload packets
+ * @wr_max:	maximum in-flight writes
+ * @wr_avail:	number of writes available
+ * @wr_unacked:	writes since last request for completion notification
+ * @wr_pending_head: head of pending write queue
+ * @wr_pending_tail: tail of pending write queue
+ * @cpl_close:	skb for cpl_close_req
+ * @cpl_abort_req: skb for cpl_abort_req
+ * @cpl_abort_rpl: skb for cpl_abort_rpl
+ * @lock:	connection status lock
+ * @refcnt:	reference count on connection
+ * @state:	connection state
+ * @saddr:	source ip/port address
+ * @daddr:	destination ip/port address
+ * @dst_cache:	reference to destination route
+ * @receive_queue: received PDUs
+ * @write_queue: un-pushed pending writes
+ * @retry_timer: retry timer for various operations
+ * @err:	connection error status
+ * @callback_lock: lock for opaque user context
+ * @user_data:	opaque user context
+ * @rcv_nxt:	next receive seq. #
+ * @copied_seq:	head of yet unread data
+ * @rcv_wup:	rcv_nxt on last window update sent
+ * @snd_nxt:	next sequence we send
+ * @snd_una:	first byte we want an ack for
+ * @write_seq:	tail+1 of data held in send buffer
+ */
+struct s3_conn {
+	struct net_device *dev;
+	struct t3cdev *cdev;
+	unsigned long flags;
+	int tid;
+	int qset;
+	int mss_idx;
+	struct l2t_entry *l2t;
+	int wr_max;
+	int wr_avail;
+	int wr_unacked;
+	struct sk_buff *wr_pending_head;
+	struct sk_buff *wr_pending_tail;
+	struct sk_buff *cpl_close;
+	struct sk_buff *cpl_abort_req;
+	struct sk_buff *cpl_abort_rpl;
+	spinlock_t lock;
+	atomic_t refcnt;
+	volatile unsigned int state;
+	struct sockaddr_in saddr;
+	struct sockaddr_in daddr;
+	struct dst_entry *dst_cache;
+	struct sk_buff_head receive_queue;
+	struct sk_buff_head write_queue;
+	struct timer_list retry_timer;
+	int err;
+	rwlock_t callback_lock;
+	void *user_data;
+
+	u32 rcv_nxt;
+	u32 copied_seq;
+	u32 rcv_wup;
+	u32 snd_nxt;
+	u32 snd_una;
+	u32 write_seq;
+};
+
+/*
+ * connection state
+ */
+enum conn_states {
+	C3CN_STATE_CONNECTING = 1,
+	C3CN_STATE_ESTABLISHED,
+	C3CN_STATE_ACTIVE_CLOSE,
+	C3CN_STATE_PASSIVE_CLOSE,
+	C3CN_STATE_CLOSE_WAIT_1,
+	C3CN_STATE_CLOSE_WAIT_2,
+	C3CN_STATE_ABORTING,
+	C3CN_STATE_CLOSED,
+};
+
+static inline unsigned int c3cn_is_closing(const struct s3_conn *c3cn)
+{
+	return c3cn->state >= C3CN_STATE_ACTIVE_CLOSE;
+}
+static inline unsigned int c3cn_is_established(const struct s3_conn *c3cn)
+{
+	return c3cn->state == C3CN_STATE_ESTABLISHED;
+}
+
+/*
+ * Connection flags -- many to track some close related events.
+ */
+enum c3cn_flags {
+	C3CN_ABORT_RPL_RCVD,	/* received one ABORT_RPL_RSS message */
+	C3CN_ABORT_REQ_RCVD,	/* received one ABORT_REQ_RSS message */
+	C3CN_ABORT_RPL_PENDING,	/* expecting an abort reply */
+	C3CN_TX_DATA_SENT,	/* already sent a TX_DATA WR */
+	C3CN_ACTIVE_CLOSE_NEEDED,	/* need to be closed */
+};
+
+/**
+ * cxgb3i_sdev_data - Per adapter data.
+ * Linked off of each Ethernet device port on the adapter.
+ * Also available via the t3cdev structure since we have pointers to our port
+ * net_device's there ...
+ *
+ * @list:	list head to link elements
+ * @cdev:	t3cdev adapter
+ * @client:	CPL client pointer
+ * @ports:	array of adapter ports
+ * @sport_map_next: next index into the port map
+ * @sport_map:	source port map
+ */
+struct cxgb3i_sdev_data {
+	struct list_head list;
+	struct t3cdev *cdev;
+	struct cxgb3_client *client;
+	struct adap_ports ports;
+	unsigned int sport_map_next;
+	unsigned long sport_map[0];
+};
+#define NDEV2CDATA(ndev) (*(struct cxgb3i_sdev_data **)&(ndev)->ec_ptr)
+#define CXGB3_SDEV_DATA(cdev) NDEV2CDATA((cdev)->lldev)
+
+void cxgb3i_sdev_cleanup(void);
+int cxgb3i_sdev_init(cxgb3_cpl_handler_func *);
+void cxgb3i_sdev_add(struct t3cdev *, struct cxgb3_client *);
+void cxgb3i_sdev_remove(struct t3cdev *);
+
+struct s3_conn *cxgb3i_c3cn_create(void);
+int cxgb3i_c3cn_connect(struct s3_conn *, struct sockaddr_in *);
+void cxgb3i_c3cn_rx_credits(struct s3_conn *, int);
+int cxgb3i_c3cn_send_pdus(struct s3_conn *, struct sk_buff *);
+void cxgb3i_c3cn_release(struct s3_conn *);
+
+/**
+ * cxgb3_skb_cb - control block for received pdu state and ULP mode management.
+ *
+ * @flag:	see C3CB_FLAG_* below
+ * @ulp_mode:	ULP mode/submode of sk_buff
+ * @seq:	tcp sequence number
+ * @ddigest:	pdu data digest
+ * @pdulen:	recovered pdu length
+ * @ulp_data:	scratch area for ULP
+ */
+struct cxgb3_skb_cb {
+	__u8 flags;
+	__u8 ulp_mode;
+	__u32 seq;
+	__u32 ddigest;
+	__u32 pdulen;
+	__u8 ulp_data[16];
+};
+
+#define CXGB3_SKB_CB(skb)	((struct cxgb3_skb_cb *)&((skb)->cb[0]))
+
+#define skb_ulp_mode(skb)	(CXGB3_SKB_CB(skb)->ulp_mode)
+#define skb_ulp_ddigest(skb)	(CXGB3_SKB_CB(skb)->ddigest)
+#define skb_ulp_pdulen(skb)	(CXGB3_SKB_CB(skb)->pdulen)
+#define skb_ulp_data(skb)	(CXGB3_SKB_CB(skb)->ulp_data)
+
+enum c3cb_flags {
+	C3CB_FLAG_NEED_HDR = 1 << 0,	/* packet needs a TX_DATA_WR header */
+	C3CB_FLAG_NO_APPEND = 1 << 1,	/* don't grow this skb */
+	C3CB_FLAG_COMPL = 1 << 2,	/* request WR completion */
+};
+
+/**
+ * sge_opaque_hdr -
+ * Opaque version of structure the SGE stores at skb->head of TX_DATA packets
+ * and for which we must reserve space.
+ */
+struct sge_opaque_hdr {
+	void *dev;
+	dma_addr_t addr[MAX_SKB_FRAGS + 1];
+};
+
+/* for TX: a skb must have a headroom of at least TX_HEADER_LEN bytes */
+#define TX_HEADER_LEN \
+		(sizeof(struct tx_data_wr) + sizeof(struct sge_opaque_hdr))
+
+/*
+ * get and set private ip for iscsi traffic
+ */
+#define cxgb3i_get_private_ipv4addr(ndev) \
+	(((struct port_info *)(netdev_priv(ndev)))->iscsi_ipv4addr)
+#define cxgb3i_set_private_ipv4addr(ndev, addr) \
+	(((struct port_info *)(netdev_priv(ndev)))->iscsi_ipv4addr) = addr
+
+/* max. connections per adapter */
+#define CXGB3I_MAX_CONN		16384
+#endif /* _CXGB3_OFFLOAD_H */
diff --git a/drivers/scsi/cxgb3i/cxgb3i_pdu.c b/drivers/scsi/cxgb3i/cxgb3i_pdu.c
new file mode 100644
index 0000000..ce7ce8c
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_pdu.c
@@ -0,0 +1,402 @@
+/*
+ * cxgb3i_pdu.c: Chelsio S3xx iSCSI driver.
+ *
+ * Copyright (c) 2008 Chelsio Communications, Inc.
+ * Copyright (c) 2008 Mike Christie
+ * Copyright (c) 2008 Red Hat, Inc.  All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * Written by: Karen Xie (kxie@chelsio.com)
+ */
+
+#include <linux/skbuff.h>
+#include <linux/crypto.h>
+#include <scsi/scsi_cmnd.h>
+#include <scsi/scsi_host.h>
+
+#include "cxgb3i.h"
+#include "cxgb3i_pdu.h"
+
+#ifdef __DEBUG_CXGB3I_RX__
+#define cxgb3i_rx_debug		cxgb3i_log_debug
+#else
+#define cxgb3i_rx_debug(fmt...)
+#endif
+
+#ifdef __DEBUG_CXGB3I_TX__
+#define cxgb3i_tx_debug		cxgb3i_log_debug
+#else
+#define cxgb3i_tx_debug(fmt...)
+#endif
+
+static struct page *pad_page;
+
+/*
+ * pdu receive, interact with libiscsi_tcp
+ */
+static inline int read_pdu_skb(struct iscsi_conn *conn, struct sk_buff *skb,
+			       unsigned int offset, int offloaded)
+{
+	int status = 0;
+	int bytes_read;
+
+	bytes_read = iscsi_tcp_recv_skb(conn, skb, offset, offloaded, &status);
+	switch (status) {
+	case ISCSI_TCP_CONN_ERR:
+		return -EIO;
+	case ISCSI_TCP_SUSPENDED:
+		/* no transfer - just have caller flush queue */
+		return bytes_read;
+	case ISCSI_TCP_SKB_DONE:
+		/*
+		 * pdus should always fit in the skb and we should get
+		 * segment done notifcation.
+		 */
+		iscsi_conn_printk(KERN_ERR, conn, "Invalid pdu or skb.");
+		return -EFAULT;
+	case ISCSI_TCP_SEGMENT_DONE:
+		return bytes_read;
+	default:
+		iscsi_conn_printk(KERN_ERR, conn, "Invalid iscsi_tcp_recv_skb "
+				  "status %d\n", status);
+		return -EINVAL;
+	}
+}
+
+static int cxgb3i_conn_read_pdu_skb(struct iscsi_conn *conn,
+				    struct sk_buff *skb)
+{
+	struct iscsi_tcp_conn *tcp_conn = conn->dd_data;
+	bool offloaded = 0;
+	unsigned int offset;
+	int rc;
+
+	cxgb3i_rx_debug("conn 0x%p, skb 0x%p, len %u, flag 0x%x.\n",
+			conn, skb, skb->len, skb_ulp_mode(skb));
+
+	if (!iscsi_tcp_recv_segment_is_hdr(tcp_conn)) {
+		iscsi_conn_failure(conn, ISCSI_ERR_PROTO);
+		return -EIO;
+	}
+
+	if (conn->hdrdgst_en && (skb_ulp_mode(skb) & ULP2_FLAG_HCRC_ERROR)) {
+		iscsi_conn_failure(conn, ISCSI_ERR_HDR_DGST);
+		return -EIO;
+	}
+
+	if (conn->datadgst_en && (skb_ulp_mode(skb) & ULP2_FLAG_DCRC_ERROR)) {
+		iscsi_conn_failure(conn, ISCSI_ERR_DATA_DGST);
+		return -EIO;
+	}
+
+	/* iscsi hdr */
+	rc = read_pdu_skb(conn, skb, 0, 0);
+	if (rc <= 0)
+		return rc;
+
+	if (iscsi_tcp_recv_segment_is_hdr(tcp_conn))
+		return 0;
+
+	offset = rc;
+	if (conn->hdrdgst_en)
+		offset += ISCSI_DIGEST_SIZE;
+
+	/* iscsi data */
+	if (skb_ulp_mode(skb) & ULP2_FLAG_DATA_DDPED) {
+		cxgb3i_rx_debug("skb 0x%p, opcode 0x%x, data %u, ddp'ed, "
+				"itt 0x%x.\n",
+				skb,
+				tcp_conn->in.hdr->opcode & ISCSI_OPCODE_MASK,
+				tcp_conn->in.datalen,
+				ntohl(tcp_conn->in.hdr->itt));
+		offloaded = 1;
+	} else {
+		cxgb3i_rx_debug("skb 0x%p, opcode 0x%x, data %u, NOT ddp'ed, "
+				"itt 0x%x.\n",
+				skb,
+				tcp_conn->in.hdr->opcode & ISCSI_OPCODE_MASK,
+				tcp_conn->in.datalen,
+				ntohl(tcp_conn->in.hdr->itt));
+		offset += sizeof(struct cpl_iscsi_hdr_norss);
+	}
+
+	rc = read_pdu_skb(conn, skb, offset, offloaded);
+	if (rc < 0)
+		return rc;
+	else
+		return 0;
+}
+
+/*
+ * pdu transmit, interact with libiscsi_tcp
+ */
+static inline void tx_skb_setmode(struct sk_buff *skb, int hcrc, int dcrc)
+{
+	u8 submode = 0;
+
+	if (hcrc)
+		submode |= 1;
+	if (dcrc)
+		submode |= 2;
+	skb_ulp_mode(skb) = (ULP_MODE_ISCSI << 4) | submode;
+}
+
+void cxgb3i_conn_cleanup_task(struct iscsi_task *task)
+{
+	struct iscsi_tcp_task *tcp_task = task->dd_data;
+
+	/* never reached the xmit task callout */
+	if (tcp_task->dd_data)
+		kfree_skb(tcp_task->dd_data);
+	tcp_task->dd_data = NULL;
+
+	/* MNC - Do we need a check in case this is called but
+	 * cxgb3i_conn_alloc_pdu has never been called on the task */
+	cxgb3i_release_itt(task, task->hdr_itt);
+	iscsi_tcp_cleanup_task(task);
+}
+
+/*
+ * We do not support ahs yet
+ */
+int cxgb3i_conn_alloc_pdu(struct iscsi_task *task, u8 opcode)
+{
+	struct iscsi_tcp_task *tcp_task = task->dd_data;
+	struct sk_buff *skb;
+
+	task->hdr = NULL;
+	/* always allocate rooms for AHS */
+	skb = alloc_skb(sizeof(struct iscsi_hdr) + ISCSI_MAX_AHS_SIZE +
+			TX_HEADER_LEN,  GFP_ATOMIC);
+	if (!skb)
+		return -ENOMEM;
+
+	cxgb3i_tx_debug("task 0x%p, opcode 0x%x, skb 0x%p.\n",
+			task, opcode, skb);
+
+	tcp_task->dd_data = skb;
+	skb_reserve(skb, TX_HEADER_LEN);
+	task->hdr = (struct iscsi_hdr *)skb->data;
+	task->hdr_max = sizeof(struct iscsi_hdr);
+
+	/* data_out uses scsi_cmd's itt */
+	if (opcode != ISCSI_OP_SCSI_DATA_OUT)
+		cxgb3i_reserve_itt(task, &task->hdr->itt);
+
+	return 0;
+}
+
+int cxgb3i_conn_init_pdu(struct iscsi_task *task, unsigned int offset,
+			      unsigned int count)
+{
+	struct iscsi_tcp_task *tcp_task = task->dd_data;
+	struct sk_buff *skb = tcp_task->dd_data;
+	struct iscsi_conn *conn = task->conn;
+	struct page *pg;
+	unsigned int datalen = count;
+	int i, padlen = iscsi_padding(count);
+	skb_frag_t *frag;
+
+	cxgb3i_tx_debug("task 0x%p,0x%p, offset %u, count %u, skb 0x%p.\n",
+			task, task->sc, offset, count, skb);
+
+	skb_put(skb, task->hdr_len);
+	tx_skb_setmode(skb, conn->hdrdgst_en, datalen ? conn->datadgst_en : 0);
+	if (!count)
+		return 0;
+
+	if (task->sc) {
+		struct scatterlist *sg;
+		struct scsi_data_buffer *sdb;
+		unsigned int sgoffset = offset;
+		struct page *sgpg;
+		unsigned int sglen;
+
+		sdb = scsi_out(task->sc);
+		sg = sdb->table.sgl;
+
+		for_each_sg(sdb->table.sgl, sg, sdb->table.nents, i) {
+			cxgb3i_tx_debug("sg %d, page 0x%p, len %u offset %u\n",
+					i, sg_page(sg), sg->length, sg->offset);
+
+			if (sgoffset < sg->length)
+				break;
+			sgoffset -= sg->length;
+		}
+		sgpg = sg_page(sg);
+		sglen = sg->length - sgoffset;
+
+		do {
+			int j = skb_shinfo(skb)->nr_frags;
+			unsigned int copy;
+
+			if (!sglen) {
+				sg = sg_next(sg);
+				sgpg = sg_page(sg);
+				sgoffset = 0;
+				sglen = sg->length;
+				++i;
+			}
+			copy = min(sglen, datalen);
+			if (j && skb_can_coalesce(skb, j, sgpg,
+						  sg->offset + sgoffset)) {
+				skb_shinfo(skb)->frags[j - 1].size += copy;
+			} else {
+				get_page(sgpg);
+				skb_fill_page_desc(skb, j, sgpg,
+						   sg->offset + sgoffset, copy);
+			}
+			sgoffset += copy;
+			sglen -= copy;
+			datalen -= copy;
+		} while (datalen);
+	} else {
+		pg = virt_to_page(task->data);
+
+		while (datalen) {
+			i = skb_shinfo(skb)->nr_frags;
+			frag = &skb_shinfo(skb)->frags[i];
+
+			get_page(pg);
+			frag->page = pg;
+			frag->page_offset = 0;
+			frag->size = min((unsigned int)PAGE_SIZE, datalen);
+
+			skb_shinfo(skb)->nr_frags++;
+			datalen -= frag->size;
+			pg++;
+		}
+	}
+
+	if (padlen) {
+		i = skb_shinfo(skb)->nr_frags;
+		frag = &skb_shinfo(skb)->frags[i];
+		frag->page = pad_page;
+		frag->page_offset = 0;
+		frag->size = padlen;
+		skb_shinfo(skb)->nr_frags++;
+	}
+
+	datalen = count + padlen;
+	skb->data_len += datalen;
+	skb->truesize += datalen;
+	skb->len += datalen;
+	return 0;
+}
+
+int cxgb3i_conn_xmit_pdu(struct iscsi_task *task)
+{
+	struct iscsi_tcp_task *tcp_task = task->dd_data;
+	struct sk_buff *skb = tcp_task->dd_data;
+	struct iscsi_tcp_conn *tcp_conn = task->conn->dd_data;
+	struct cxgb3i_conn *cconn = tcp_conn->dd_data;
+	unsigned int datalen;
+	int err;
+
+	if (!skb)
+		return 0;
+
+	datalen = skb->data_len;
+	tcp_task->dd_data = NULL;
+	err = cxgb3i_c3cn_send_pdus(cconn->cep->c3cn, skb);
+	cxgb3i_tx_debug("task 0x%p, skb 0x%p, len %u/%u, rv %d.\n",
+			task, skb, skb->len, skb->data_len, err);
+	if (err > 0) {
+		int pdulen = err;
+
+		if (task->conn->hdrdgst_en)
+			pdulen += ISCSI_DIGEST_SIZE;
+		if (datalen && task->conn->datadgst_en)
+			pdulen += ISCSI_DIGEST_SIZE;
+
+		task->conn->txdata_octets += pdulen;
+		return 0;
+	}
+
+	if (err < 0 && err != -EAGAIN) {
+		kfree_skb(skb);
+		cxgb3i_tx_debug("itt 0x%x, skb 0x%p, len %u/%u, xmit err %d.\n",
+				task->itt, skb, skb->len, skb->data_len, err);
+		iscsi_conn_printk(KERN_ERR, task->conn, "xmit err %d.\n", err);
+		iscsi_conn_failure(task->conn, ISCSI_ERR_XMIT_FAILED);
+		return err;
+	}
+	/* reset skb to send when we are called again */
+	tcp_task->dd_data = skb;
+	return -EAGAIN;
+}
+
+int cxgb3i_pdu_init(void)
+{
+	pad_page = alloc_page(GFP_KERNEL);
+	if (!pad_page)
+		return -ENOMEM;
+	memset(page_address(pad_page), 0, PAGE_SIZE);
+	return 0;
+}
+
+void cxgb3i_pdu_cleanup(void)
+{
+	if (pad_page) {
+		__free_page(pad_page);
+		pad_page = NULL;
+	}
+}
+
+void cxgb3i_conn_pdu_ready(struct s3_conn *c3cn)
+{
+	struct sk_buff *skb;
+	unsigned int read = 0;
+	struct iscsi_conn *conn = c3cn->user_data;
+	int err = 0;
+
+	cxgb3i_rx_debug("cn 0x%p.\n", c3cn);
+
+	read_lock(&c3cn->callback_lock);
+	if (unlikely(!conn || conn->suspend_rx)) {
+		cxgb3i_rx_debug("conn 0x%p, id %d, suspend_rx %lu!\n",
+				conn, conn ? conn->id : 0xFF,
+				conn ? conn->suspend_rx : 0xFF);
+		read_unlock(&c3cn->callback_lock);
+		return;
+	}
+	skb = skb_peek(&c3cn->receive_queue);
+	while (!err && skb) {
+		__skb_unlink(skb, &c3cn->receive_queue);
+		read += skb_ulp_pdulen(skb);
+		err = cxgb3i_conn_read_pdu_skb(conn, skb);
+		__kfree_skb(skb);
+		skb = skb_peek(&c3cn->receive_queue);
+	}
+	read_unlock(&c3cn->callback_lock);
+	if (c3cn) {
+		c3cn->copied_seq += read;
+		cxgb3i_c3cn_rx_credits(c3cn, read);
+	}
+	conn->rxdata_octets += read;
+}
+
+void cxgb3i_conn_tx_open(struct s3_conn *c3cn)
+{
+	struct iscsi_conn *conn = c3cn->user_data;
+
+	cxgb3i_tx_debug("cn 0x%p.\n", c3cn);
+	if (conn) {
+		cxgb3i_tx_debug("cn 0x%p, cid %d.\n", c3cn, conn->id);
+		scsi_queue_work(conn->session->host, &conn->xmitwork);
+	}
+}
+
+void cxgb3i_conn_closing(struct s3_conn *c3cn)
+{
+	struct iscsi_conn *conn;
+
+	read_lock(&c3cn->callback_lock);
+	conn = c3cn->user_data;
+	if (conn && c3cn->state != C3CN_STATE_ESTABLISHED)
+		iscsi_conn_failure(conn, ISCSI_ERR_CONN_FAILED);
+	read_unlock(&c3cn->callback_lock);
+}
diff --git a/drivers/scsi/cxgb3i/cxgb3i_pdu.h b/drivers/scsi/cxgb3i/cxgb3i_pdu.h
new file mode 100644
index 0000000..a3f685c
--- /dev/null
+++ b/drivers/scsi/cxgb3i/cxgb3i_pdu.h
@@ -0,0 +1,59 @@
+/*
+ * cxgb3i_ulp2.h: Chelsio S3xx iSCSI driver.
+ *
+ * Copyright (c) 2008 Chelsio Communications, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * Written by: Karen Xie (kxie@chelsio.com)
+ */
+
+#ifndef __CXGB3I_ULP2_PDU_H__
+#define __CXGB3I_ULP2_PDU_H__
+
+struct cpl_iscsi_hdr_norss {
+	union opcode_tid ot;
+	u16 pdu_len_ddp;
+	u16 len;
+	u32 seq;
+	u16 urg;
+	u8 rsvd;
+	u8 status;
+};
+
+struct cpl_rx_data_ddp_norss {
+	union opcode_tid ot;
+	u16 urg;
+	u16 len;
+	u32 seq;
+	u32 nxt_seq;
+	u32 ulp_crc;
+	u32 ddp_status;
+};
+
+#define RX_DDP_STATUS_IPP_SHIFT		27	/* invalid pagepod */
+#define RX_DDP_STATUS_TID_SHIFT		26	/* tid mismatch */
+#define RX_DDP_STATUS_COLOR_SHIFT	25	/* color mismatch */
+#define RX_DDP_STATUS_OFFSET_SHIFT	24	/* offset mismatch */
+#define RX_DDP_STATUS_ULIMIT_SHIFT	23	/* ulimit error */
+#define RX_DDP_STATUS_TAG_SHIFT		22	/* tag mismatch */
+#define RX_DDP_STATUS_DCRC_SHIFT	21	/* dcrc error */
+#define RX_DDP_STATUS_HCRC_SHIFT	20	/* hcrc error */
+#define RX_DDP_STATUS_PAD_SHIFT		19	/* pad error */
+#define RX_DDP_STATUS_PPP_SHIFT		18	/* pagepod parity error */
+#define RX_DDP_STATUS_LLIMIT_SHIFT	17	/* llimit error */
+#define RX_DDP_STATUS_DDP_SHIFT		16	/* ddp'able */
+#define RX_DDP_STATUS_PMM_SHIFT		15	/* pagepod mismatch */
+
+#define ULP2_FLAG_DATA_READY		0x1
+#define ULP2_FLAG_DATA_DDPED		0x2
+#define ULP2_FLAG_HCRC_ERROR		0x10
+#define ULP2_FLAG_DCRC_ERROR		0x20
+#define ULP2_FLAG_PAD_ERROR		0x40
+
+void cxgb3i_conn_closing(struct s3_conn *);
+void cxgb3i_conn_pdu_ready(struct s3_conn *c3cn);
+void cxgb3i_conn_tx_open(struct s3_conn *c3cn);
+#endif