Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (zl6100) Enable interval between chip accesses for all chips
  hwmon: (w83627ehf) Describe undocumented pwm attributes
  hwmon: (w83627ehf) Fix temp2 source for W83627UHG
  hwmon: (w83627ehf) Fix memory leak in probe function
  hwmon: (w83627ehf) Fix writing into fan_stop_time for NCT6775F/NCT6776F

4 files changed, 24 insertions, 28 deletions

diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index 3f44dbd..ceaf6f6 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -50,7 +50,7 @@ W83627DHG, W83627DHG-P, W83627UHG, W83667HG, W83667HG-B, W83667HG-I
 (NCT6775F), and NCT6776F super I/O chips. We will refer to them collectively
 as Winbond chips.
 
-The chips implement 2 to 4 temperature sensors (9 for NCT6775F and NCT6776F),
+The chips implement 3 to 4 temperature sensors (9 for NCT6775F and NCT6776F),
 2 to 5 fan rotation speed sensors, 8 to 10 analog voltage sensors, one VID
 (except for 627UHG), alarms with beep warnings (control unimplemented),
 and some automatic fan regulation strategies (plus manual fan control mode).
@@ -143,8 +143,13 @@ pwm[1-4]_min_output - minimum fan speed (range 1 - 255), when the temperature
 pwm[1-4]_stop_time  - how many milliseconds [ms] must elapse to switch
                       corresponding fan off. (when the temperature was below
                       defined range).
+pwm[1-4]_start_output-minimum fan speed (range 1 - 255) when spinning up
+pwm[1-4]_step_output- rate of fan speed change (1 - 255)
+pwm[1-4]_stop_output- minimum fan speed (range 1 - 255) when spinning down
+pwm[1-4]_max_output - maximum fan speed (range 1 - 255), when the temperature
+                      is above defined range.
 
-Note: last two functions are influenced by other control bits, not yet exported
+Note: last six functions are influenced by other control bits, not yet exported
       by the driver, so a change might not have any effect.
 
 Implementation Details
diff --git a/Documentation/hwmon/zl6100 b/Documentation/hwmon/zl6100
index 51f76a1..a4e8d90 100644
--- a/Documentation/hwmon/zl6100
+++ b/Documentation/hwmon/zl6100
@@ -88,14 +88,12 @@ Module parameters
 delay
 -----
 
-Some Intersil/Zilker Labs DC-DC controllers require a minimum interval between
-I2C bus accesses. According to Intersil, the minimum interval is 2 ms, though
-1 ms appears to be sufficient and has not caused any problems in testing.
-The problem is known to affect ZL6100, ZL2105, and ZL2008. It is known not to
-affect ZL2004 and ZL6105. The driver automatically sets the interval to 1 ms
-except for ZL2004 and ZL6105. To enable manual override, the driver provides a
-writeable module parameter, 'delay', which can be used to set the interval to
-a value between 0 and 65,535 microseconds.
+Intersil/Zilker Labs DC-DC controllers require a minimum interval between I2C
+bus accesses. According to Intersil, the minimum interval is 2 ms, though 1 ms
+appears to be sufficient and has not caused any problems in testing. The problem
+is known to affect all currently supported chips. For manual override, the
+driver provides a writeable module parameter, 'delay', which can be used to set
+the interval to a value between 0 and 65,535 microseconds.
 
 
 Sysfs entries
diff --git a/drivers/hwmon/pmbus/zl6100.c b/drivers/hwmon/pmbus/zl6100.c
index 880b90c..e3e8420 100644
--- a/drivers/hwmon/pmbus/zl6100.c
+++ b/drivers/hwmon/pmbus/zl6100.c
@@ -200,17 +200,11 @@ static int zl6100_probe(struct i2c_client *client,
 	data->id = mid->driver_data;
 
 	/*
-	 * ZL2005, ZL2008, ZL2105, and ZL6100 are known to require a wait time
-	 * between I2C accesses. ZL2004 and ZL6105 are known to be safe.
-	 * Other chips have not yet been tested.
-	 *
-	 * Only clear the wait time for chips known to be safe. The wait time
-	 * can be cleared later for additional chips if tests show that it
-	 * is not needed (in other words, better be safe than sorry).
+	 * According to information from the chip vendor, all currently
+	 * supported chips are known to require a wait time between I2C
+	 * accesses.
 	 */
 	data->delay = delay;
-	if (data->id == zl2004 || data->id == zl6105)
-		data->delay = 0;
 
 	/*
 	 * Since there was a direct I2C device access above, wait before
diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c
index 5276d19..a658d62 100644
--- a/drivers/hwmon/w83627ehf.c
+++ b/drivers/hwmon/w83627ehf.c
@@ -39,7 +39,7 @@
 					       0x8860 0xa1
     w83627dhg    9      5       4       3      0xa020 0xc1    0x5ca3
     w83627dhg-p  9      5       4       3      0xb070 0xc1    0x5ca3
-    w83627uhg    8      2       2       2      0xa230 0xc1    0x5ca3
+    w83627uhg    8      2       2       3      0xa230 0xc1    0x5ca3
     w83667hg     9      5       3       3      0xa510 0xc1    0x5ca3
     w83667hg-b   9      5       3       4      0xb350 0xc1    0x5ca3
     nct6775f     9      4       3       9      0xb470 0xc1    0x5ca3
@@ -1607,7 +1607,7 @@ store_##reg(struct device *dev, struct device_attribute *attr, \
 	val = step_time_to_reg(val, data->pwm_mode[nr]); \
 	mutex_lock(&data->update_lock); \
 	data->reg[nr] = val; \
-	w83627ehf_write_value(data, W83627EHF_REG_##REG[nr], val); \
+	w83627ehf_write_value(data, data->REG_##REG[nr], val); \
 	mutex_unlock(&data->update_lock); \
 	return count; \
 } \
@@ -2004,7 +2004,8 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 		goto exit;
 	}
 
-	data = kzalloc(sizeof(struct w83627ehf_data), GFP_KERNEL);
+	data = devm_kzalloc(&pdev->dev, sizeof(struct w83627ehf_data),
+			    GFP_KERNEL);
 	if (!data) {
 		err = -ENOMEM;
 		goto exit_release;
@@ -2157,16 +2158,16 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 		w83627ehf_set_temp_reg_ehf(data, 3);
 
 		/*
-		 * Temperature sources for temp1 and temp2 are selected with
+		 * Temperature sources for temp2 and temp3 are selected with
 		 * bank 0, registers 0x49 and 0x4a.
 		 */
 		data->temp_src[0] = 0;	/* SYSTIN */
 		reg = w83627ehf_read_value(data, 0x49) & 0x07;
 		/* Adjust to have the same mapping as other source registers */
 		if (reg == 0)
-			data->temp_src[1]++;
+			data->temp_src[1] = 1;
 		else if (reg >= 2 && reg <= 5)
-			data->temp_src[1] += 2;
+			data->temp_src[1] = reg + 2;
 		else	/* should never happen */
 			data->have_temp &= ~(1 << 1);
 		reg = w83627ehf_read_value(data, 0x4a);
@@ -2493,9 +2494,8 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
 
 exit_remove:
 	w83627ehf_device_remove_files(dev);
-	kfree(data);
-	platform_set_drvdata(pdev, NULL);
 exit_release:
+	platform_set_drvdata(pdev, NULL);
 	release_region(res->start, IOREGION_LENGTH);
 exit:
 	return err;
@@ -2509,7 +2509,6 @@ static int __devexit w83627ehf_remove(struct platform_device *pdev)
 	w83627ehf_device_remove_files(&pdev->dev);
 	release_region(data->addr, IOREGION_LENGTH);
 	platform_set_drvdata(pdev, NULL);
-	kfree(data);
 
 	return 0;
 }