Merge branch 'amba' of git://git.linaro.org/people/rmk/linux-arm

Pull #2 ARM updates from Russell King:
 "Further ARM AMBA primecell updates which aren't included directly in
  the previous commit.  I wanted to keep these separate as they're
  touching stuff outside arch/arm/."

* 'amba' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7362/1: AMBA: Add module_amba_driver() helper macro for amba_driver
  ARM: 7335/1: mach-u300: do away with MMC config files
  ARM: 7280/1: mmc: mmci: Cache MMCICLOCK and MMCIPOWER register
  ARM: 7309/1: realview: fix unconnected interrupts on EB11MP
  ARM: 7230/1: mmc: mmci: Fix PIO read for small SDIO packets
  ARM: 7227/1: mmc: mmci: Prepare for SDIO before setting up DMA job
  ARM: 7223/1: mmc: mmci: Fixup use of runtime PM and use autosuspend
  ARM: 7221/1: mmc: mmci: Change from using legacy suspend
  ARM: 7219/1: mmc: mmci: Change vdd_handler to a generic ios_handler
  ARM: 7218/1: mmc: mmci: Provide option to configure bus signal direction
  ARM: 7217/1: mmc: mmci: Put power register deviations in variant data
  ARM: 7216/1: mmc: mmci: Do not release spinlock in request_end
  ARM: 7215/1: mmc: mmci: Increase max_segs from 16 to 128

17 files changed, 202 insertions, 265 deletions

diff --git a/arch/arm/mach-realview/include/mach/irqs-eb.h b/arch/arm/mach-realview/include/mach/irqs-eb.h
index 204d537..d6b5073 100644
--- a/arch/arm/mach-realview/include/mach/irqs-eb.h
+++ b/arch/arm/mach-realview/include/mach/irqs-eb.h
@@ -96,16 +96,19 @@
 #define IRQ_EB11MP_L220_SLAVE	(IRQ_EB_GIC_START + 30)
 #define IRQ_EB11MP_L220_DECODE	(IRQ_EB_GIC_START + 31)
 
-#define IRQ_EB11MP_UART2	-1
-#define IRQ_EB11MP_UART3	-1
-#define IRQ_EB11MP_CLCD		-1
-#define IRQ_EB11MP_DMA		-1
-#define IRQ_EB11MP_WDOG		-1
-#define IRQ_EB11MP_GPIO0	-1
-#define IRQ_EB11MP_GPIO1	-1
-#define IRQ_EB11MP_GPIO2	-1
-#define IRQ_EB11MP_SCI		-1
-#define IRQ_EB11MP_SSP		-1
+/*
+ * The 11MPcore tile leaves the following unconnected.
+ */
+#define IRQ_EB11MP_UART2	0
+#define IRQ_EB11MP_UART3	0
+#define IRQ_EB11MP_CLCD		0
+#define IRQ_EB11MP_DMA		0
+#define IRQ_EB11MP_WDOG		0
+#define IRQ_EB11MP_GPIO0	0
+#define IRQ_EB11MP_GPIO1	0
+#define IRQ_EB11MP_GPIO2	0
+#define IRQ_EB11MP_SCI		0
+#define IRQ_EB11MP_SSP		0
 
 #define NR_GIC_EB11MP		2
 
diff --git a/arch/arm/mach-u300/Makefile b/arch/arm/mach-u300/Makefile
index 2855381..fd3a5c3 100644
--- a/arch/arm/mach-u300/Makefile
+++ b/arch/arm/mach-u300/Makefile
@@ -8,7 +8,6 @@ obj-n		:=
 obj-		:=
 
 obj-$(CONFIG_ARCH_U300)	          += u300.o
-obj-$(CONFIG_MMC)                 += mmc.o
 obj-$(CONFIG_SPI_PL022)           += spi.o
 obj-$(CONFIG_MACH_U300_SPIDUMMY)  += dummyspichip.o
 obj-$(CONFIG_I2C_STU300)          += i2c.o
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index b911590..8b90c44 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -18,6 +18,7 @@
 #include <linux/termios.h>
 #include <linux/dmaengine.h>
 #include <linux/amba/bus.h>
+#include <linux/amba/mmci.h>
 #include <linux/amba/serial.h>
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
@@ -44,9 +45,9 @@
 #include <mach/gpio-u300.h>
 
 #include "clock.h"
-#include "mmc.h"
 #include "spi.h"
 #include "i2c.h"
+#include "u300-gpio.h"
 
 /*
  * Static I/O mappings that are needed for booting the U300 platforms. The
@@ -117,11 +118,6 @@ static AMBA_APB_DEVICE(uart1, "uart1", 0, U300_UART1_BASE,
 /* AHB device at 0x4000 offset */
 static AMBA_APB_DEVICE(pl172, "pl172", 0, U300_EMIF_CFG_BASE, { }, NULL);
 
-
-/*
- * Everything within this next ifdef deals with external devices connected to
- * the APP SPI bus.
- */
 /* Fast device at 0x6000 offset */
 static AMBA_APB_DEVICE(pl022, "pl022", 0, U300_SPI_BASE,
 	{ IRQ_U300_SPI }, NULL);
@@ -129,8 +125,26 @@ static AMBA_APB_DEVICE(pl022, "pl022", 0, U300_SPI_BASE,
 /* Fast device at 0x1000 offset */
 #define U300_MMCSD_IRQS	{ IRQ_U300_MMCSD_MCIINTR0, IRQ_U300_MMCSD_MCIINTR1 }
 
+static struct mmci_platform_data mmcsd_platform_data = {
+	/*
+	 * Do not set ocr_mask or voltage translation function,
+	 * we have a regulator we can control instead.
+	 */
+	.f_max = 24000000,
+	.gpio_wp = -1,
+	.gpio_cd = U300_GPIO_PIN_MMC_CD,
+	.cd_invert = true,
+	.capabilities = MMC_CAP_MMC_HIGHSPEED |
+	MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
+#ifdef CONFIG_COH901318
+	.dma_filter = coh901318_filter_id,
+	.dma_rx_param = (void *) U300_DMA_MMCSD_RX_TX,
+	/* Don't specify a TX channel, this RX channel is bidirectional */
+#endif
+};
+
 static AMBA_APB_DEVICE(mmcsd, "mmci", 0, U300_MMCSD_BASE,
-	U300_MMCSD_IRQS, NULL);
+	U300_MMCSD_IRQS, &mmcsd_platform_data);
 
 /*
  * The order of device declaration may be important, since some devices
@@ -1830,16 +1844,6 @@ void __init u300_init_devices(void)
 	writew(val, U300_SYSCON_VBASE + U300_SYSCON_SMCR);
 }
 
-static int core_module_init(void)
-{
-	/*
-	 * This needs to be initialized later: it needs the input framework
-	 * to be initialized first.
-	 */
-	return mmc_init(&mmcsd_device);
-}
-module_init(core_module_init);
-
 /* Forward declare this function from the watchdog */
 void coh901327_watchdog_reset(void);
 
diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c
deleted file mode 100644
index 05abd6a..0000000
--- a/arch/arm/mach-u300/mmc.c
+++ /dev/null
@@ -1,52 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/mmc.c
- *
- *
- * Copyright (C) 2009 ST-Ericsson SA
- * License terms: GNU General Public License (GPL) version 2
- *
- * Author: Linus Walleij <linus.walleij@stericsson.com>
- * Author: Johan Lundin
- * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- */
-#include <linux/device.h>
-#include <linux/amba/bus.h>
-#include <linux/mmc/host.h>
-#include <linux/dmaengine.h>
-#include <linux/amba/mmci.h>
-#include <linux/slab.h>
-#include <mach/coh901318.h>
-#include <mach/dma_channels.h>
-
-#include "u300-gpio.h"
-#include "mmc.h"
-
-static struct mmci_platform_data mmc0_plat_data = {
-	/*
-	 * Do not set ocr_mask or voltage translation function,
-	 * we have a regulator we can control instead.
-	 */
-	/* Nominally 2.85V on our platform */
-	.f_max = 24000000,
-	.gpio_wp = -1,
-	.gpio_cd = U300_GPIO_PIN_MMC_CD,
-	.cd_invert = true,
-	.capabilities = MMC_CAP_MMC_HIGHSPEED |
-	MMC_CAP_SD_HIGHSPEED | MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
-#ifdef CONFIG_COH901318
-	.dma_filter = coh901318_filter_id,
-	.dma_rx_param = (void *) U300_DMA_MMCSD_RX_TX,
-	/* Don't specify a TX channel, this RX channel is bidirectional */
-#endif
-};
-
-int __devinit mmc_init(struct amba_device *adev)
-{
-	struct device *mmcsd_device = &adev->dev;
-	int ret = 0;
-
-	mmcsd_device->platform_data = &mmc0_plat_data;
-
-	return ret;
-}
diff --git a/arch/arm/mach-u300/mmc.h b/arch/arm/mach-u300/mmc.h
deleted file mode 100644
index 92b8512..0000000
--- a/arch/arm/mach-u300/mmc.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/mmc.h
- *
- *
- * Copyright (C) 2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- *
- * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- */
-#ifndef MMC_H
-#define MMC_H
-
-#include <linux/amba/bus.h>
-
-int __devinit mmc_init(struct amba_device *adev);
-
-#endif
diff --git a/arch/arm/mach-ux500/board-mop500-sdi.c b/arch/arm/mach-ux500/board-mop500-sdi.c
index 5dde4d4..1daead3 100644
--- a/arch/arm/mach-ux500/board-mop500-sdi.c
+++ b/arch/arm/mach-ux500/board-mop500-sdi.c
@@ -31,21 +31,13 @@
  * SDI 0 (MicroSD slot)
  */
 
-/* MMCIPOWER bits */
-#define MCI_DATA2DIREN		(1 << 2)
-#define MCI_CMDDIREN		(1 << 3)
-#define MCI_DATA0DIREN		(1 << 4)
-#define MCI_DATA31DIREN		(1 << 5)
-#define MCI_FBCLKEN		(1 << 7)
-
 /* GPIO pins used by the sdi0 level shifter */
 static int sdi0_en = -1;
 static int sdi0_vsel = -1;
 
-static u32 mop500_sdi0_vdd_handler(struct device *dev, unsigned int vdd,
-				   unsigned char power_mode)
+static int mop500_sdi0_ios_handler(struct device *dev, struct mmc_ios *ios)
 {
-	switch (power_mode) {
+	switch (ios->power_mode) {
 	case MMC_POWER_UP:
 	case MMC_POWER_ON:
 		/*
@@ -65,8 +57,7 @@ static u32 mop500_sdi0_vdd_handler(struct device *dev, unsigned int vdd,
 		break;
 	}
 
-	return MCI_FBCLKEN | MCI_CMDDIREN | MCI_DATA0DIREN |
-	       MCI_DATA2DIREN | MCI_DATA31DIREN;
+	return 0;
 }
 
 #ifdef CONFIG_STE_DMA40
@@ -90,13 +81,17 @@ static struct stedma40_chan_cfg mop500_sdi0_dma_cfg_tx = {
 #endif
 
 static struct mmci_platform_data mop500_sdi0_data = {
-	.vdd_handler	= mop500_sdi0_vdd_handler,
+	.ios_handler	= mop500_sdi0_ios_handler,
 	.ocr_mask	= MMC_VDD_29_30,
 	.f_max		= 50000000,
 	.capabilities	= MMC_CAP_4_BIT_DATA |
 				MMC_CAP_SD_HIGHSPEED |
 				MMC_CAP_MMC_HIGHSPEED,
 	.gpio_wp	= -1,
+	.sigdir		= MCI_ST_FBCLKEN |
+				MCI_ST_CMDDIREN |
+				MCI_ST_DATA0DIREN |
+				MCI_ST_DATA2DIREN,
 #ifdef CONFIG_STE_DMA40
 	.dma_filter	= stedma40_filter,
 	.dma_rx_param	= &mop500_sdi0_dma_cfg_rx,
diff --git a/drivers/char/hw_random/nomadik-rng.c b/drivers/char/hw_random/nomadik-rng.c
index 3d3c1e6..96de024 100644
--- a/drivers/char/hw_random/nomadik-rng.c
+++ b/drivers/char/hw_random/nomadik-rng.c
@@ -107,17 +107,6 @@ static struct amba_driver nmk_rng_driver = {
 	.id_table = nmk_rng_ids,
 };
 
-static int __init nmk_rng_init(void)
-{
-	return amba_driver_register(&nmk_rng_driver);
-}
-
-static void __devexit nmk_rng_exit(void)
-{
-	amba_driver_unregister(&nmk_rng_driver);
-}
-
-module_init(nmk_rng_init);
-module_exit(nmk_rng_exit);
+module_amba_driver(nmk_rng_driver);
 
 MODULE_LICENSE("GPL");
diff --git a/drivers/dma/pl330.c b/drivers/dma/pl330.c
index b8ec03e..16b66c8 100644
--- a/drivers/dma/pl330.c
+++ b/drivers/dma/pl330.c
@@ -1035,18 +1035,7 @@ static struct amba_driver pl330_driver = {
 	.remove = pl330_remove,
 };
 
-static int __init pl330_init(void)
-{
-	return amba_driver_register(&pl330_driver);
-}
-module_init(pl330_init);
-
-static void __exit pl330_exit(void)
-{
-	amba_driver_unregister(&pl330_driver);
-	return;
-}
-module_exit(pl330_exit);
+module_amba_driver(pl330_driver);
 
 MODULE_AUTHOR("Jaswinder Singh <jassi.brar@samsung.com>");
 MODULE_DESCRIPTION("API Driver for PL330 DMAC");
diff --git a/drivers/input/serio/ambakmi.c b/drivers/input/serio/ambakmi.c
index 8407d5b..2ffd110 100644
--- a/drivers/input/serio/ambakmi.c
+++ b/drivers/input/serio/ambakmi.c
@@ -208,18 +208,7 @@ static struct amba_driver ambakmi_driver = {
 	.resume		= amba_kmi_resume,
 };
 
-static int __init amba_kmi_init(void)
-{
-	return amba_driver_register(&ambakmi_driver);
-}
-
-static void __exit amba_kmi_exit(void)
-{
-	amba_driver_unregister(&ambakmi_driver);
-}
-
-module_init(amba_kmi_init);
-module_exit(amba_kmi_exit);
+module_amba_driver(ambakmi_driver);
 
 MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
 MODULE_DESCRIPTION("AMBA KMI controller driver");
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index bdfd055..983e244e 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -53,6 +53,8 @@ static unsigned int fmax = 515633;
  * @sdio: variant supports SDIO
  * @st_clkdiv: true if using a ST-specific clock divider algorithm
  * @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
+ * @pwrreg_powerup: power up value for MMCIPOWER register
+ * @signal_direction: input/out direction of bus signals can be indicated
  */
 struct variant_data {
 	unsigned int		clkreg;
@@ -63,18 +65,22 @@ struct variant_data {
 	bool			sdio;
 	bool			st_clkdiv;
 	bool			blksz_datactrl16;
+	u32			pwrreg_powerup;
+	bool			signal_direction;
 };
 
 static struct variant_data variant_arm = {
 	.fifosize		= 16 * 4,
 	.fifohalfsize		= 8 * 4,
 	.datalength_bits	= 16,
+	.pwrreg_powerup		= MCI_PWR_UP,
 };
 
 static struct variant_data variant_arm_extended_fifo = {
 	.fifosize		= 128 * 4,
 	.fifohalfsize		= 64 * 4,
 	.datalength_bits	= 16,
+	.pwrreg_powerup		= MCI_PWR_UP,
 };
 
 static struct variant_data variant_u300 = {
@@ -83,6 +89,8 @@ static struct variant_data variant_u300 = {
 	.clkreg_enable		= MCI_ST_U300_HWFCEN,
 	.datalength_bits	= 16,
 	.sdio			= true,
+	.pwrreg_powerup		= MCI_PWR_ON,
+	.signal_direction	= true,
 };
 
 static struct variant_data variant_ux500 = {
@@ -93,6 +101,8 @@ static struct variant_data variant_ux500 = {
 	.datalength_bits	= 24,
 	.sdio			= true,
 	.st_clkdiv		= true,
+	.pwrreg_powerup		= MCI_PWR_ON,
+	.signal_direction	= true,
 };
 
 static struct variant_data variant_ux500v2 = {
@@ -104,11 +114,35 @@ static struct variant_data variant_ux500v2 = {
 	.sdio			= true,
 	.st_clkdiv		= true,
 	.blksz_datactrl16	= true,
+	.pwrreg_powerup		= MCI_PWR_ON,
+	.signal_direction	= true,
 };
 
 /*
  * This must be called with host->lock held
  */
+static void mmci_write_clkreg(struct mmci_host *host, u32 clk)
+{
+	if (host->clk_reg != clk) {
+		host->clk_reg = clk;
+		writel(clk, host->base + MMCICLOCK);
+	}
+}
+
+/*
+ * This must be called with host->lock held
+ */
+static void mmci_write_pwrreg(struct mmci_host *host, u32 pwr)
+{
+	if (host->pwr_reg != pwr) {
+		host->pwr_reg = pwr;
+		writel(pwr, host->base + MMCIPOWER);
+	}
+}
+
+/*
+ * This must be called with host->lock held
+ */
 static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
 {
 	struct variant_data *variant = host->variant;
@@ -153,7 +187,7 @@ static void mmci_set_clkreg(struct mmci_host *host, unsigned int desired)
 	if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_8)
 		clk |= MCI_ST_8BIT_BUS;
 
-	writel(clk, host->base + MMCICLOCK);
+	mmci_write_clkreg(host, clk);
 }
 
 static void
@@ -166,14 +200,10 @@ mmci_request_end(struct mmci_host *host, struct mmc_request *mrq)
 	host->mrq = NULL;
 	host->cmd = NULL;
 
-	/*
-	 * Need to drop the host lock here; mmc_request_done may call
-	 * back into the driver...
-	 */
-	spin_unlock(&host->lock);
-	pm_runtime_put(mmc_dev(host->mmc));
 	mmc_request_done(host->mmc, mrq);
-	spin_lock(&host->lock);
+
+	pm_runtime_mark_last_busy(mmc_dev(host->mmc));
+	pm_runtime_put_autosuspend(mmc_dev(host->mmc));
 }
 
 static void mmci_set_mask1(struct mmci_host *host, unsigned int mask)
@@ -607,6 +637,11 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
 	if (data->flags & MMC_DATA_READ)
 		datactrl |= MCI_DPSM_DIRECTION;
 
+	/* The ST Micro variants has a special bit to enable SDIO */
+	if (variant->sdio && host->mmc->card)
+		if (mmc_card_sdio(host->mmc->card))
+			datactrl |= MCI_ST_DPSM_SDIOEN;
+
 	/*
 	 * Attempt to use DMA operation mode, if this
 	 * should fail, fall back to PIO mode
@@ -635,11 +670,6 @@ static void mmci_start_data(struct mmci_host *host, struct mmc_data *data)
 		irqmask = MCI_TXFIFOHALFEMPTYMASK;
 	}
 
-	/* The ST Micro variants has a special bit to enable SDIO */
-	if (variant->sdio && host->mmc->card)
-		if (mmc_card_sdio(host->mmc->card))
-			datactrl |= MCI_ST_DPSM_SDIOEN;
-
 	writel(datactrl, base + MMCIDATACTRL);
 	writel(readl(base + MMCIMASK0) & ~MCI_DATAENDMASK, base + MMCIMASK0);
 	mmci_set_mask1(host, irqmask);
@@ -786,7 +816,24 @@ static int mmci_pio_read(struct mmci_host *host, char *buffer, unsigned int rema
 		if (count <= 0)
 			break;
 
-		readsl(base + MMCIFIFO, ptr, count >> 2);
+		/*
+		 * SDIO especially may want to send something that is
+		 * not divisible by 4 (as opposed to card sectors
+		 * etc). Therefore make sure to always read the last bytes
+		 * while only doing full 32-bit reads towards the FIFO.
+		 */
+		if (unlikely(count & 0x3)) {
+			if (count < 4) {
+				unsigned char buf[4];
+				readsl(base + MMCIFIFO, buf, 1);
+				memcpy(ptr, buf, count);
+			} else {
+				readsl(base + MMCIFIFO, ptr, count >> 2);
+				count &= ~0x3;
+			}
+		} else {
+			readsl(base + MMCIFIFO, ptr, count >> 2);
+		}
 
 		ptr += count;
 		remain -= count;
@@ -821,14 +868,13 @@ static int mmci_pio_write(struct mmci_host *host, char *buffer, unsigned int rem
 		 */
 		if (variant->sdio &&
 		    mmc_card_sdio(host->mmc->card)) {
+			u32 clk;
 			if (count < 8)
-				writel(readl(host->base + MMCICLOCK) &
-					~variant->clkreg_enable,
-					host->base + MMCICLOCK);
+				clk = host->clk_reg & ~variant->clkreg_enable;
 			else
-				writel(readl(host->base + MMCICLOCK) |
-					variant->clkreg_enable,
-					host->base + MMCICLOCK);
+				clk = host->clk_reg | variant->clkreg_enable;
+
+			mmci_write_clkreg(host, clk);
 		}
 
 		/*
@@ -1015,10 +1061,17 @@ static void mmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
 static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct mmci_host *host = mmc_priv(mmc);
+	struct variant_data *variant = host->variant;
 	u32 pwr = 0;
 	unsigned long flags;
 	int ret;
 
+	pm_runtime_get_sync(mmc_dev(mmc));
+
+	if (host->plat->ios_handler &&
+		host->plat->ios_handler(mmc_dev(mmc), ios))
+			dev_err(mmc_dev(mmc), "platform ios_handler failed\n");
+
 	switch (ios->power_mode) {
 	case MMC_POWER_OFF:
 		if (host->vcc)
@@ -1035,22 +1088,38 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 				 * power should be rare so we print an error
 				 * and return here.
 				 */
-				return;
+				goto out;
 			}
 		}
-		if (host->plat->vdd_handler)
-			pwr |= host->plat->vdd_handler(mmc_dev(mmc), ios->vdd,
-						       ios->power_mode);
-		/* The ST version does not have this, fall through to POWER_ON */
-		if (host->hw_designer != AMBA_VENDOR_ST) {
-			pwr |= MCI_PWR_UP;
-			break;
-		}
+		/*
+		 * The ST Micro variant doesn't have the PL180s MCI_PWR_UP
+		 * and instead uses MCI_PWR_ON so apply whatever value is
+		 * configured in the variant data.
+		 */
+		pwr |= variant->pwrreg_powerup;
+
+		break;
 	case MMC_POWER_ON:
 		pwr |= MCI_PWR_ON;
 		break;
 	}
 
+	if (variant->signal_direction && ios->power_mode != MMC_POWER_OFF) {
+		/*
+		 * The ST Micro variant has some additional bits
+		 * indicating signal direction for the signals in
+		 * the SD/MMC bus and feedback-clock usage.
+		 */
+		pwr |= host->plat->sigdir;
+
+		if (ios->bus_width == MMC_BUS_WIDTH_4)
+			pwr &= ~MCI_ST_DATA74DIREN;
+		else if (ios->bus_width == MMC_BUS_WIDTH_1)
+			pwr &= (~MCI_ST_DATA74DIREN &
+				~MCI_ST_DATA31DIREN &
+				~MCI_ST_DATA2DIREN);
+	}
+
 	if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) {
 		if (host->hw_designer != AMBA_VENDOR_ST)
 			pwr |= MCI_ROD;
@@ -1066,13 +1135,13 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	spin_lock_irqsave(&host->lock, flags);
 
 	mmci_set_clkreg(host, ios->clock);
-
-	if (host->pwr != pwr) {
-		host->pwr = pwr;
-		writel(pwr, host->base + MMCIPOWER);
-	}
+	mmci_write_pwrreg(host, pwr);
 
 	spin_unlock_irqrestore(&host->lock, flags);
+
+ out:
+	pm_runtime_mark_last_busy(mmc_dev(mmc));
+	pm_runtime_put_autosuspend(mmc_dev(mmc));
 }
 
 static int mmci_get_ro(struct mmc_host *mmc)
@@ -1346,6 +1415,8 @@ static int __devinit mmci_probe(struct amba_device *dev,
 
 	mmci_dma_setup(host);
 
+	pm_runtime_set_autosuspend_delay(&dev->dev, 50);
+	pm_runtime_use_autosuspend(&dev->dev);
 	pm_runtime_put(&dev->dev);
 
 	mmc_add_host(mmc);
@@ -1430,43 +1501,49 @@ static int __devexit mmci_remove(struct amba_device *dev)
 	return 0;
 }
 
-#ifdef CONFIG_PM
-static int mmci_suspend(struct amba_device *dev, pm_message_t state)
+#ifdef CONFIG_SUSPEND
+static int mmci_suspend(struct device *dev)
 {
-	struct mmc_host *mmc = amba_get_drvdata(dev);
+	struct amba_device *adev = to_amba_device(dev);
+	struct mmc_host *mmc = amba_get_drvdata(adev);
 	int ret = 0;
 
 	if (mmc) {
 		struct mmci_host *host = mmc_priv(mmc);
 
 		ret = mmc_suspend_host(mmc);
-		if (ret == 0)
+		if (ret == 0) {
+			pm_runtime_get_sync(dev);
 			writel(0, host->base + MMCIMASK0);
+		}
 	}
 
 	return ret;
 }
 
-static int mmci_resume(struct amba_device *dev)
+static int mmci_resume(struct device *dev)
 {
-	struct mmc_host *mmc = amba_get_drvdata(dev);
+	struct amba_device *adev = to_amba_device(dev);
+	struct mmc_host *mmc = amba_get_drvdata(adev);
 	int ret = 0;
 
 	if (mmc) {
 		struct mmci_host *host = mmc_priv(mmc);
 
 		writel(MCI_IRQENABLE, host->base + MMCIMASK0);
+		pm_runtime_put(dev);
 
 		ret = mmc_resume_host(mmc);
 	}
 
 	return ret;
 }
-#else
-#define mmci_suspend	NULL
-#define mmci_resume	NULL
 #endif
 
+static const struct dev_pm_ops mmci_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(mmci_suspend, mmci_resume)
+};
+
 static struct amba_id mmci_ids[] = {
 	{
 		.id	= 0x00041180,
@@ -1512,26 +1589,15 @@ MODULE_DEVICE_TABLE(amba, mmci_ids);
 static struct amba_driver mmci_driver = {
 	.drv		= {
 		.name	= DRIVER_NAME,
+		.pm	= &mmci_dev_pm_ops,
 	},
 	.probe		= mmci_probe,
 	.remove		= __devexit_p(mmci_remove),
-	.suspend	= mmci_suspend,
-	.resume		= mmci_resume,
 	.id_table	= mmci_ids,
 };
 
-static int __init mmci_init(void)
-{
-	return amba_driver_register(&mmci_driver);
-}
-
-static void __exit mmci_exit(void)
-{
-	amba_driver_unregister(&mmci_driver);
-}
+module_amba_driver(mmci_driver);
 
-module_init(mmci_init);
-module_exit(mmci_exit);
 module_param(fmax, uint, 0444);
 
 MODULE_DESCRIPTION("ARM PrimeCell PL180/181 Multimedia Card Interface driver");
diff --git a/drivers/mmc/host/mmci.h b/drivers/mmc/host/mmci.h
index 79e4143..d437ccf 100644
--- a/drivers/mmc/host/mmci.h
+++ b/drivers/mmc/host/mmci.h
@@ -13,16 +13,6 @@
 #define MCI_PWR_ON		0x03
 #define MCI_OD			(1 << 6)
 #define MCI_ROD			(1 << 7)
-/*
- * The ST Micro version does not have ROD and reuse the voltage registers
- * for direction settings
- */
-#define MCI_ST_DATA2DIREN	(1 << 2)
-#define MCI_ST_CMDDIREN		(1 << 3)
-#define MCI_ST_DATA0DIREN	(1 << 4)
-#define MCI_ST_DATA31DIREN	(1 << 5)
-#define MCI_ST_FBCLKEN		(1 << 7)
-#define MCI_ST_DATA74DIREN	(1 << 8)
 
 #define MMCICLOCK		0x004
 #define MCI_CLK_ENABLE		(1 << 8)
@@ -160,7 +150,7 @@
 	(MCI_RXFIFOHALFFULLMASK | MCI_RXDATAAVLBLMASK | \
 	 MCI_TXFIFOHALFEMPTYMASK)
 
-#define NR_SG		16
+#define NR_SG		128
 
 struct clk;
 struct variant_data;
@@ -189,7 +179,8 @@ struct mmci_host {
 
 	unsigned int		mclk;
 	unsigned int		cclk;
-	u32			pwr;
+	u32			pwr_reg;
+	u32			clk_reg;
 	struct mmci_platform_data *plat;
 	struct variant_data	*variant;
 
diff --git a/drivers/rtc/rtc-pl030.c b/drivers/rtc/rtc-pl030.c
index a4a1e534..22bacdb 100644
--- a/drivers/rtc/rtc-pl030.c
+++ b/drivers/rtc/rtc-pl030.c
@@ -185,18 +185,7 @@ static struct amba_driver pl030_driver = {
 	.id_table	= pl030_ids,
 };
 
-static int __init pl030_init(void)
-{
-	return amba_driver_register(&pl030_driver);
-}
-
-static void __exit pl030_exit(void)
-{
-	amba_driver_unregister(&pl030_driver);
-}
-
-module_init(pl030_init);
-module_exit(pl030_exit);
+module_amba_driver(pl030_driver);
 
 MODULE_AUTHOR("Russell King <rmk@arm.linux.org.uk>");
 MODULE_DESCRIPTION("ARM AMBA PL030 RTC Driver");
diff --git a/drivers/rtc/rtc-pl031.c b/drivers/rtc/rtc-pl031.c
index 3a470e2..692de73 100644
--- a/drivers/rtc/rtc-pl031.c
+++ b/drivers/rtc/rtc-pl031.c
@@ -431,18 +431,7 @@ static struct amba_driver pl031_driver = {
 	.remove = pl031_remove,
 };
 
-static int __init pl031_init(void)
-{
-	return amba_driver_register(&pl031_driver);
-}
-
-static void __exit pl031_exit(void)
-{
-	amba_driver_unregister(&pl031_driver);
-}
-
-module_init(pl031_init);
-module_exit(pl031_exit);
+module_amba_driver(pl031_driver);
 
 MODULE_AUTHOR("Deepak Saxena <dsaxena@plexity.net");
 MODULE_DESCRIPTION("ARM AMBA PL031 RTC Driver");
diff --git a/drivers/watchdog/sp805_wdt.c b/drivers/watchdog/sp805_wdt.c
index eef1524..3ff9e47 100644
--- a/drivers/watchdog/sp805_wdt.c
+++ b/drivers/watchdog/sp805_wdt.c
@@ -370,17 +370,7 @@ static struct amba_driver sp805_wdt_driver = {
 	.remove = __devexit_p(sp805_wdt_remove),
 };
 
-static int __init sp805_wdt_init(void)
-{
-	return amba_driver_register(&sp805_wdt_driver);
-}
-module_init(sp805_wdt_init);
-
-static void __exit sp805_wdt_exit(void)
-{
-	amba_driver_unregister(&sp805_wdt_driver);
-}
-module_exit(sp805_wdt_exit);
+module_amba_driver(sp805_wdt_driver);
 
 module_param(nowayout, int, 0);
 MODULE_PARM_DESC(nowayout,
diff --git a/include/linux/amba/bus.h b/include/linux/amba/bus.h
index a9fab83..7847e19 100644
--- a/include/linux/amba/bus.h
+++ b/include/linux/amba/bus.h
@@ -125,4 +125,13 @@ struct amba_device name##_device = {				\
 	.periphid = id,						\
 }
 
+/*
+ * module_amba_driver() - Helper macro for drivers that don't do anything
+ * special in module init/exit.  This eliminates a lot of boilerplate.  Each
+ * module may only use this macro once, and calling it replaces module_init()
+ * and module_exit()
+ */
+#define module_amba_driver(__amba_drv) \
+	module_driver(__amba_drv, amba_driver_register, amba_driver_unregister)
+
 #endif
diff --git a/include/linux/amba/mmci.h b/include/linux/amba/mmci.h
index 0101e9c..32a89cf 100644
--- a/include/linux/amba/mmci.h
+++ b/include/linux/amba/mmci.h
@@ -6,6 +6,19 @@
 
 #include <linux/mmc/host.h>
 
+
+/*
+ * These defines is places here due to access is needed from machine
+ * configuration files. The ST Micro version does not have ROD and
+ * reuse the voltage registers for direction settings.
+ */
+#define MCI_ST_DATA2DIREN	(1 << 2)
+#define MCI_ST_CMDDIREN		(1 << 3)
+#define MCI_ST_DATA0DIREN	(1 << 4)
+#define MCI_ST_DATA31DIREN	(1 << 5)
+#define MCI_ST_FBCLKEN		(1 << 7)
+#define MCI_ST_DATA74DIREN	(1 << 8)
+
 /* Just some dummy forwarding */
 struct dma_chan;
 
@@ -18,7 +31,8 @@ struct dma_chan;
  * @ocr_mask: available voltages on the 4 pins from the block, this
  * is ignored if a regulator is used, see the MMC_VDD_* masks in
  * mmc/host.h
- * @vdd_handler: a callback function to translate a MMC_VDD_*
+ * @ios_handler: a callback function to act on specfic ios changes,
+ * used for example to control a levelshifter
  * mask into a value to be binary (or set some other custom bits
  * in MMCIPWR) or:ed and written into the MMCIPWR register of the
  * block.  May also control external power based on the power_mode.
@@ -31,6 +45,8 @@ struct dma_chan;
  * @capabilities: the capabilities of the block as implemented in
  * this platform, signify anything MMC_CAP_* from mmc/host.h
  * @capabilities2: more capabilities, MMC_CAP2_* from mmc/host.h
+ * @sigdir: a bit field indicating for what bits in the MMC bus the host
+ * should enable signal direction indication.
  * @dma_filter: function used to select an appropriate RX and TX
  * DMA channel to be used for DMA, if and only if you're deploying the
  * generic DMA engine
@@ -46,14 +62,14 @@ struct dma_chan;
 struct mmci_platform_data {
 	unsigned int f_max;
 	unsigned int ocr_mask;
-	u32 (*vdd_handler)(struct device *, unsigned int vdd,
-			   unsigned char power_mode);
+	int (*ios_handler)(struct device *, struct mmc_ios *);
 	unsigned int (*status)(struct device *);
 	int	gpio_wp;
 	int	gpio_cd;
 	bool	cd_invert;
 	unsigned long capabilities;
 	unsigned long capabilities2;
+	u32 sigdir;
 	bool (*dma_filter)(struct dma_chan *chan, void *filter_param);
 	void *dma_rx_param;
 	void *dma_tx_param;
diff --git a/sound/arm/aaci.c b/sound/arm/aaci.c
index b37b702a..5119fda 100644
--- a/sound/arm/aaci.c
+++ b/sound/arm/aaci.c
@@ -1110,18 +1110,7 @@ static struct amba_driver aaci_driver = {
 	.id_table	= aaci_ids,
 };
 
-static int __init aaci_init(void)
-{
-	return amba_driver_register(&aaci_driver);
-}
-
-static void __exit aaci_exit(void)
-{
-	amba_driver_unregister(&aaci_driver);
-}
-
-module_init(aaci_init);
-module_exit(aaci_exit);
+module_amba_driver(aaci_driver);
 
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION("ARM PrimeCell PL041 Advanced Audio CODEC Interface driver");