Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes and straggler patches from Olof Johansson:
 "A collection of fixes for fall out from 3.10 merge window, some build
  fixes and warning cleanups and a small handful of patches that were
  small and contained and made sense to still include in 3.10 (some of
  these have also been in -next since the merge window opened).

  Largest continous series is for OMAP, but there's a handful for other
  platforms.

  For i.MX, one of the patches are framebuffer fixups due to fallout
  during the merge window, and the other removes some stale and broken
  code."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
  ARM: exynos: dts: Fixed vbus-gpios
  ARM: EXYNOS5: Fix kernel dump in AFTR idle mode
  ARM: ux500: Rid ignored return value of regulator_enable() compiler warning
  ARM: ux500: read the correct soc_id number
  ARM: exynos: dts: cros5250: add cyapa trackpad
  video: mxsfb: Adapt to new videomode API
  ARM: imx: Select GENERIC_ALLOCATOR
  ARM: imx: compile fix for hotplug.c
  ARM: dts: don't assume boards are using twl4030 for omap3
  ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
  ARM: dts: Configure and fix the McSPI pins for 4430sdp
  ARM: dts: AM33XX: Add GPMC node
  ARM: dts: OMAP4460: Fix CPU OPP voltages
  ARM: dts: OMAP36xx: Fix CPU OPP voltages
  ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
  ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
  omap: mux: add AM/DM37x gpios
  ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
  ARM: OMAP2+: omap_device: use late_initcall_sync
  ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
  ...

45 files changed, 173 insertions, 235 deletions

diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
index e7f8d7e..6a983c1 100644
--- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -56,20 +56,20 @@ Example for an AM33xx board:
 			nand-bus-width = <16>;
 			ti,nand-ecc-opt = "bch8";
 
-			gpmc,sync-clk = <0>;
-			gpmc,cs-on = <0>;
-			gpmc,cs-rd-off = <44>;
-			gpmc,cs-wr-off = <44>;
-			gpmc,adv-on = <6>;
-			gpmc,adv-rd-off = <34>;
-			gpmc,adv-wr-off = <44>;
-			gpmc,we-off = <40>;
-			gpmc,oe-off = <54>;
-			gpmc,access = <64>;
-			gpmc,rd-cycle = <82>;
-			gpmc,wr-cycle = <82>;
-			gpmc,wr-access = <40>;
-			gpmc,wr-data-mux-bus = <0>;
+			gpmc,sync-clk-ps = <0>;
+			gpmc,cs-on-ns = <0>;
+			gpmc,cs-rd-off-ns = <44>;
+			gpmc,cs-wr-off-ns = <44>;
+			gpmc,adv-on-ns = <6>;
+			gpmc,adv-rd-off-ns = <34>;
+			gpmc,adv-wr-off-ns = <44>;
+			gpmc,we-off-ns = <40>;
+			gpmc,oe-off-ns = <54>;
+			gpmc,access-ns = <64>;
+			gpmc,rd-cycle-ns = <82>;
+			gpmc,wr-cycle-ns = <82>;
+			gpmc,wr-access-ns = <40>;
+			gpmc,wr-data-mux-bus-ns = <0>;
 
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt
index 24cb4e4..ace4a64 100644
--- a/Documentation/devicetree/bindings/net/gpmc-eth.txt
+++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt
@@ -26,16 +26,16 @@ Required properties:
 - bank-width: 		Address width of the device in bytes. GPMC supports 8-bit
 			and 16-bit devices and so must be either 1 or 2 bytes.
 - compatible:		Compatible string property for the ethernet child device.
-- gpmc,cs-on:		Chip-select assertion time
-- gpmc,cs-rd-off:	Chip-select de-assertion time for reads
-- gpmc,cs-wr-off:	Chip-select de-assertion time for writes
-- gpmc,oe-on:		Output-enable assertion time
-- gpmc,oe-off		Output-enable de-assertion time
-- gpmc,we-on:		Write-enable assertion time
-- gpmc,we-off:		Write-enable de-assertion time
-- gpmc,access:		Start cycle to first data capture (read access)
-- gpmc,rd-cycle:	Total read cycle time
-- gpmc,wr-cycle:	Total write cycle time
+- gpmc,cs-on-ns:	Chip-select assertion time
+- gpmc,cs-rd-off-ns:	Chip-select de-assertion time for reads
+- gpmc,cs-wr-off-ns:	Chip-select de-assertion time for writes
+- gpmc,oe-on-ns:	Output-enable assertion time
+- gpmc,oe-off-ns:	Output-enable de-assertion time
+- gpmc,we-on-ns:	Write-enable assertion time
+- gpmc,we-off-ns:	Write-enable de-assertion time
+- gpmc,access-ns:	Start cycle to first data capture (read access)
+- gpmc,rd-cycle-ns:	Total read cycle time
+- gpmc,wr-cycle-ns:	Total write cycle time
 - reg:			Chip-select, base address (relative to chip-select)
 			and size of the memory mapped for the device.
 			Note that base address will be typically 0 as this
@@ -65,24 +65,24 @@ gpmc: gpmc@6e000000 {
 		bank-width = <2>;
 
 		gpmc,mux-add-data;
-		gpmc,cs-on = <0>;
-		gpmc,cs-rd-off = <186>;
-		gpmc,cs-wr-off = <186>;
-		gpmc,adv-on = <12>;
-		gpmc,adv-rd-off = <48>;
-		gpmc,adv-wr-off = <48>;
-		gpmc,oe-on = <54>;
-		gpmc,oe-off = <168>;
-		gpmc,we-on = <54>;
-		gpmc,we-off = <168>;
-		gpmc,rd-cycle = <186>;
-		gpmc,wr-cycle = <186>;
-		gpmc,access = <114>;
-		gpmc,page-burst-access = <6>;
-		gpmc,bus-turnaround = <12>;
-		gpmc,cycle2cycle-delay = <18>;
-		gpmc,wr-data-mux-bus = <90>;
-		gpmc,wr-access = <186>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
 		gpmc,cycle2cycle-samecsen;
 		gpmc,cycle2cycle-diffcsen;
 
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 46e2b52..d423d58 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -897,7 +897,6 @@ config ARCH_MULTI_V7
 	bool "ARMv7 based platforms (Cortex-A, PJ4, Scorpion, Krait)"
 	default y
 	select ARCH_MULTI_V6_V7
-	select ARCH_VEXPRESS
 	select CPU_V7
 
 config ARCH_MULTI_V6_V7
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index d110110..1460d9b 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -403,5 +403,17 @@
 			       0x44d80000 0x2000>;	/* M3 DMEM */
 			ti,hwmods = "wkup_m3";
 		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			reg = <0x50000000 0x2000>;
+			interrupts = <100>;
+			num-cs = <7>;
+			num-waitpins = <2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/cros5250-common.dtsi b/arch/arm/boot/dts/cros5250-common.dtsi
index 0a61bbb..3f0239e 100644
--- a/arch/arm/boot/dts/cros5250-common.dtsi
+++ b/arch/arm/boot/dts/cros5250-common.dtsi
@@ -175,6 +175,14 @@
 	i2c@12C70000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <378000>;
+
+		trackpad {
+			reg = <0x67>;
+			compatible = "cypress,cyapa";
+			interrupts = <2 0>;
+			interrupt-parent = <&gpx1>;
+			wakeup-source;
+		};
 	};
 
 	i2c@12C80000 {
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
index 26d856b..3e0c792 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
@@ -214,7 +214,7 @@
 	};
 
 	usb@12110000 {
-		samsung,vbus-gpio = <&gpx2 6 1 3 3>;
+		samsung,vbus-gpio = <&gpx2 6 0>;
 	};
 
 	dp-controller {
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index bf4744b..d449feb 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -183,7 +183,7 @@
 	};
 
 	usb@12110000 {
-		samsung,vbus-gpio = <&gpx1 1 1 3 3>;
+		samsung,vbus-gpio = <&gpx1 1 0>;
 	};
 
 	fixed-rate-clocks {
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index 5a31964..3046d1f 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -122,6 +122,7 @@
 
 &usb_otg_hs {
 	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
 	mode = <3>;
 	power = <50>;
 };
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index 05f51e1..96d1c20 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -68,6 +68,7 @@
 
 &usb_otg_hs {
 	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
 	mode = <3>;
 	power = <50>;
 };
diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi
index d4a7280d..a626c50 100644
--- a/arch/arm/boot/dts/omap3-overo.dtsi
+++ b/arch/arm/boot/dts/omap3-overo.dtsi
@@ -73,6 +73,7 @@
 
 &usb_otg_hs {
 	interface-type = <0>;
+	usb-phy = <&usb2_phy>;
 	mode = <3>;
 	power = <50>;
 };
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 4ad03d9..82a404d 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -519,7 +519,6 @@
 			interrupts = <0 92 0x4>, <0 93 0x4>;
 			interrupt-names = "mc", "dma";
 			ti,hwmods = "usb_otg_hs";
-			usb-phy = <&usb2_phy>;
 			multipoint = <1>;
 			num-eps = <16>;
 			ram-bits = <12>;
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index b89233e..f3447bc 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -20,9 +20,9 @@
 		cpu@0 {
 			operating-points = <
 				/* kHz    uV */
-				300000   975000
-				600000  1075000
-				800000  1200000
+				300000  1012500
+				600000  1200000
+				800000  1325000
 			>;
 			clock-latency = <300000>; /* From legacy driver */
 		};
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index c387bdc..a35d9cd 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -223,6 +223,15 @@
 		>;
 	};
 
+	mcspi1_pins: pinmux_mcspi1_pins {
+		pinctrl-single,pins = <
+			0xf2 0x100	/*  mcspi1_clk.mcspi1_clk INPUT | MODE0 */
+			0xf4 0x100	/*  mcspi1_somi.mcspi1_somi INPUT | MODE0 */
+			0xf6 0x100	/*  mcspi1_simo.mcspi1_simo INPUT | MODE0 */
+			0xf8 0x100	/*  mcspi1_cs0.mcspi1_cs0 INPUT | MODE0*/
+		>;
+	};
+
 	dss_hdmi_pins: pinmux_dss_hdmi_pins {
 		pinctrl-single,pins = <
 			0x5a 0x118	/* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */
@@ -358,12 +367,15 @@
 };
 
 &mcspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcspi1_pins>;
+
 	eth@0 {
 		compatible = "ks8851";
 		spi-max-frequency = <24000000>;
 		reg = <0>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <2>; /* gpio line 34 */
+		interrupts = <2 8>; /* gpio line 34, low triggered */
 		vdd-supply = <&vdd_eth>;
 	};
 };
diff --git a/arch/arm/boot/dts/omap4-var-som.dts b/arch/arm/boot/dts/omap4-var-som.dts
index 222a413..7e04103 100644
--- a/arch/arm/boot/dts/omap4-var-som.dts
+++ b/arch/arm/boot/dts/omap4-var-som.dts
@@ -68,7 +68,7 @@
 		spi-max-frequency = <24000000>;
 		reg = <0>;
 		interrupt-parent = <&gpio6>;
-		interrupts = <11>; /* gpio line 171 */
+		interrupts = <11 8>; /* gpio line 171, low triggered */
 		vdd-supply = <&vdd_eth>;
 	};
 };
diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi
index 7c2c23c..2cf227c 100644
--- a/arch/arm/boot/dts/omap4460.dtsi
+++ b/arch/arm/boot/dts/omap4460.dtsi
@@ -15,9 +15,9 @@
 		cpu@0 {
 			operating-points = <
 				/* kHz    uV */
-				350000   975000
-				700000  1075000
-				920000  1200000
+				350000  1025000
+				700000  1200000
+				920000  1313000
 			>;
 			clock-latency = <300000>; /* From legacy driver */
 		};
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index 33903ca..c1ef64b 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -137,6 +137,8 @@ CONFIG_SERIAL_8250_DETECT_IRQ=y
 CONFIG_SERIAL_8250_RSA=y
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_OMAP=y
+CONFIG_SERIAL_OMAP_CONSOLE=y
 CONFIG_HW_RANDOM=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_SPI=y
@@ -153,6 +155,7 @@ CONFIG_OMAP_WATCHDOG=y
 CONFIG_TWL4030_WATCHDOG=y
 CONFIG_MFD_TPS65217=y
 CONFIG_MFD_TPS65910=y
+CONFIG_TWL6040_CORE=y
 CONFIG_REGULATOR_TWL4030=y
 CONFIG_REGULATOR_TPS65023=y
 CONFIG_REGULATOR_TPS6507X=y
@@ -195,6 +198,7 @@ CONFIG_SND_USB_AUDIO=m
 CONFIG_SND_SOC=m
 CONFIG_SND_OMAP_SOC=m
 CONFIG_SND_OMAP_SOC_OMAP_TWL4030=m
+CONFIG_SND_OMAP_SOC_OMAP_ABE_TWL6040=m
 CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m
 CONFIG_USB=y
 CONFIG_USB_DEBUG=y
diff --git a/arch/arm/kernel/devtree.c b/arch/arm/kernel/devtree.c
index 70f1bde..5af04f6 100644
--- a/arch/arm/kernel/devtree.c
+++ b/arch/arm/kernel/devtree.c
@@ -180,6 +180,13 @@ struct machine_desc * __init setup_machine_fdt(unsigned int dt_phys)
 	unsigned long dt_root;
 	const char *model;
 
+#ifdef CONFIG_ARCH_MULTIPLATFORM
+	DT_MACHINE_START(GENERIC_DT, "Generic DT based system")
+	MACHINE_END
+
+	mdesc_best = (struct machine_desc *)&__mach_desc_GENERIC_DT;
+#endif
+
 	if (!dt_phys)
 		return NULL;
 
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index 728007c..1522c7a 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -18,6 +18,7 @@
 #include <linux/bootmem.h>
 #include <linux/seq_file.h>
 #include <linux/screen_info.h>
+#include <linux/of_platform.h>
 #include <linux/init.h>
 #include <linux/kexec.h>
 #include <linux/of_fdt.h>
@@ -659,9 +660,19 @@ struct screen_info screen_info = {
 
 static int __init customize_machine(void)
 {
-	/* customizes platform devices, or adds new ones */
+	/*
+	 * customizes platform devices, or adds new ones
+	 * On DT based machines, we fall back to populating the
+	 * machine from the device tree, if no callback is provided,
+	 * otherwise we would always need an init_machine callback.
+	 */
 	if (machine_desc->init_machine)
 		machine_desc->init_machine();
+#ifdef CONFIG_OF
+	else
+		of_platform_populate(NULL, of_default_bus_match_table,
+					NULL, NULL);
+#endif
 	return 0;
 }
 arch_initcall(customize_machine);
diff --git a/arch/arm/mach-exynos/include/mach/regs-pmu.h b/arch/arm/mach-exynos/include/mach/regs-pmu.h
index 3f30aa1..57344b7 100644
--- a/arch/arm/mach-exynos/include/mach/regs-pmu.h
+++ b/arch/arm/mach-exynos/include/mach/regs-pmu.h
@@ -344,6 +344,7 @@
 #define EXYNOS5_FSYS_ARM_OPTION					S5P_PMUREG(0x2208)
 #define EXYNOS5_ISP_ARM_OPTION					S5P_PMUREG(0x2288)
 #define EXYNOS5_ARM_COMMON_OPTION				S5P_PMUREG(0x2408)
+#define EXYNOS5_ARM_L2_OPTION					S5P_PMUREG(0x2608)
 #define EXYNOS5_TOP_PWR_OPTION					S5P_PMUREG(0x2C48)
 #define EXYNOS5_TOP_PWR_SYSMEM_OPTION				S5P_PMUREG(0x2CC8)
 #define EXYNOS5_JPEG_MEM_OPTION					S5P_PMUREG(0x2F48)
diff --git a/arch/arm/mach-exynos/pmu.c b/arch/arm/mach-exynos/pmu.c
index daebc1a..97d6885 100644
--- a/arch/arm/mach-exynos/pmu.c
+++ b/arch/arm/mach-exynos/pmu.c
@@ -228,6 +228,7 @@ static struct exynos_pmu_conf exynos5250_pmu_config[] = {
 	{ EXYNOS5_DIS_IRQ_ISP_ARM_CENTRAL_SYS_PWR_REG,	{ 0x0, 0x0, 0x0} },
 	{ EXYNOS5_ARM_COMMON_SYS_PWR_REG,		{ 0x0, 0x0, 0x2} },
 	{ EXYNOS5_ARM_L2_SYS_PWR_REG,			{ 0x3, 0x3, 0x3} },
+	{ EXYNOS5_ARM_L2_OPTION,			{ 0x10, 0x10, 0x0 } },
 	{ EXYNOS5_CMU_ACLKSTOP_SYS_PWR_REG,		{ 0x1, 0x0, 0x1} },
 	{ EXYNOS5_CMU_SCLKSTOP_SYS_PWR_REG,		{ 0x1, 0x0, 0x1} },
 	{ EXYNOS5_CMU_RESET_SYS_PWR_REG,		{ 0x1, 0x1, 0x0} },
@@ -353,11 +354,9 @@ static void exynos5_init_pmu(void)
 
 	/*
 	 * SKIP_DEACTIVATE_ACEACP_IN_PWDN_BITFIELD Enable
-	 * MANUAL_L2RSTDISABLE_CONTROL_BITFIELD Enable
 	 */
 	tmp = __raw_readl(EXYNOS5_ARM_COMMON_OPTION);
-	tmp |= (EXYNOS5_MANUAL_L2RSTDISABLE_CONTROL |
-		EXYNOS5_SKIP_DEACTIVATE_ACEACP_IN_PWDN);
+	tmp |= EXYNOS5_SKIP_DEACTIVATE_ACEACP_IN_PWDN;
 	__raw_writel(tmp, EXYNOS5_ARM_COMMON_OPTION);
 
 	/*
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 78f795d..ba44328 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -5,6 +5,7 @@ config ARCH_MXC
 	select AUTO_ZRELADDR if !ZBOOT_ROM
 	select CLKDEV_LOOKUP
 	select CLKSRC_MMIO
+	select GENERIC_ALLOCATOR
 	select GENERIC_CLOCKEVENTS
 	select GENERIC_IRQ_CHIP
 	select MULTI_IRQ_HANDLER
@@ -61,10 +62,6 @@ config MXC_ULPI
 config ARCH_HAS_RNGA
 	bool
 
-config IRAM_ALLOC
-	bool
-	select GENERIC_ALLOCATOR
-
 config HAVE_IMX_ANATOP
 	bool
 
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 9309589..70ae7c4 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -23,7 +23,6 @@ obj-$(CONFIG_ARCH_MXC_IOMUX_V3) += iomux-v3.o
 obj-$(CONFIG_MXC_TZIC) += tzic.o
 obj-$(CONFIG_MXC_AVIC) += avic.o
 
-obj-$(CONFIG_IRAM_ALLOC) += iram_alloc.o
 obj-$(CONFIG_MXC_ULPI) += ulpi.o
 obj-$(CONFIG_MXC_USE_EPIT) += epit.o
 obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index 4cba7db..c08ae3f 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -12,6 +12,7 @@
 #define __ASM_ARCH_MXC_COMMON_H__
 
 struct platform_device;
+struct pt_regs;
 struct clk;
 enum mxc_cpu_pwr_mode;
 
diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S
index a58c8b0..67b9c48 100644
--- a/arch/arm/mach-imx/headsmp.S
+++ b/arch/arm/mach-imx/headsmp.S
@@ -24,7 +24,7 @@ ENTRY(v7_secondary_startup)
 ENDPROC(v7_secondary_startup)
 #endif
 
-#ifdef CONFIG_PM
+#ifdef CONFIG_ARM_CPU_SUSPEND
 /*
  * The following code must assume it is running from physical address
  * where absolute virtual addresses to the data section have to be
diff --git a/arch/arm/mach-imx/hotplug.c b/arch/arm/mach-imx/hotplug.c
index 5e91112..3daf1ed 100644
--- a/arch/arm/mach-imx/hotplug.c
+++ b/arch/arm/mach-imx/hotplug.c
@@ -11,7 +11,9 @@
  */
 
 #include <linux/errno.h>
+#include <linux/jiffies.h>
 #include <asm/cp15.h>
+#include <asm/proc-fns.h>
 
 #include "common.h"
 
diff --git a/arch/arm/mach-imx/iram_alloc.c b/arch/arm/mach-imx/iram_alloc.c
deleted file mode 100644
index e05cf40..0000000
--- a/arch/arm/mach-imx/iram_alloc.c
+++ /dev/null
@@ -1,73 +0,0 @@
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-
-#include <linux/kernel.h>
-#include <linux/io.h>
-#include <linux/module.h>
-#include <linux/spinlock.h>
-#include <linux/genalloc.h>
-#include "linux/platform_data/imx-iram.h"
-
-static unsigned long iram_phys_base;
-static void __iomem *iram_virt_base;
-static struct gen_pool *iram_pool;
-
-static inline void __iomem *iram_phys_to_virt(unsigned long p)
-{
-	return iram_virt_base + (p - iram_phys_base);
-}
-
-void __iomem *iram_alloc(unsigned int size, unsigned long *dma_addr)
-{
-	if (!iram_pool)
-		return NULL;
-
-	*dma_addr = gen_pool_alloc(iram_pool, size);
-	pr_debug("iram alloc - %dB@0x%lX\n", size, *dma_addr);
-	if (!*dma_addr)
-		return NULL;
-	return iram_phys_to_virt(*dma_addr);
-}
-EXPORT_SYMBOL(iram_alloc);
-
-void iram_free(unsigned long addr, unsigned int size)
-{
-	if (!iram_pool)
-		return;
-
-	gen_pool_free(iram_pool, addr, size);
-}
-EXPORT_SYMBOL(iram_free);
-
-int __init iram_init(unsigned long base, unsigned long size)
-{
-	iram_phys_base = base;
-
-	iram_pool = gen_pool_create(PAGE_SHIFT, -1);
-	if (!iram_pool)
-		return -ENOMEM;
-
-	gen_pool_add(iram_pool, base, size, -1);
-	iram_virt_base = ioremap(iram_phys_base, size);
-	if (!iram_virt_base)
-		return -EIO;
-
-	pr_debug("i.MX IRAM pool: %ld KB@0x%p\n", size / 1024, iram_virt_base);
-	return 0;
-}
diff --git a/arch/arm/mach-omap1/dma.c b/arch/arm/mach-omap1/dma.c
index 1a4e887..68ab858 100644
--- a/arch/arm/mach-omap1/dma.c
+++ b/arch/arm/mach-omap1/dma.c
@@ -301,7 +301,7 @@ static int __init omap1_system_dma_init(void)
 	if (ret) {
 		dev_err(&pdev->dev, "%s: Unable to add resources for %s%d\n",
 			__func__, pdev->name, pdev->id);
-		goto exit_device_put;
+		goto exit_iounmap;
 	}
 
 	p = kzalloc(sizeof(struct omap_system_dma_plat_info), GFP_KERNEL);
@@ -309,7 +309,7 @@ static int __init omap1_system_dma_init(void)
 		dev_err(&pdev->dev, "%s: Unable to allocate 'p' for %s\n",
 			__func__, pdev->name);
 		ret = -ENOMEM;
-		goto exit_device_del;
+		goto exit_iounmap;
 	}
 
 	d = kzalloc(sizeof(struct omap_dma_dev_attr), GFP_KERNEL);
@@ -402,8 +402,8 @@ exit_release_d:
 	kfree(d);
 exit_release_p:
 	kfree(p);
-exit_device_del:
-	platform_device_del(pdev);
+exit_iounmap:
+	iounmap(dma_base);
 exit_device_put:
 	platform_device_put(pdev);
 
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 857b1f0..f49cd51 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -37,8 +37,6 @@ config ARCH_OMAP2PLUS_TYPICAL
 	select NEON if ARCH_OMAP3 || ARCH_OMAP4 || SOC_OMAP5
 	select PM_RUNTIME
 	select REGULATOR
-	select SERIAL_OMAP
-	select SERIAL_OMAP_CONSOLE
 	select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4
 	select TWL4030_POWER if ARCH_OMAP3 || ARCH_OMAP4
 	select VFP
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 62bb352..55a9d67 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -32,12 +32,12 @@ obj-$(CONFIG_SOC_HAS_OMAP2_SDRC)	+= sdrc.o
 
 # SMP support ONLY available for OMAP4
 
-obj-$(CONFIG_SMP)			+= omap-smp.o omap-headsmp.o
-obj-$(CONFIG_HOTPLUG_CPU)		+= omap-hotplug.o
+smp-$(CONFIG_SMP)			+= omap-smp.o omap-headsmp.o
+smp-$(CONFIG_HOTPLUG_CPU)		+= omap-hotplug.o
 omap-4-5-common				=  omap4-common.o omap-wakeupgen.o \
 					   sleep44xx.o
-obj-$(CONFIG_ARCH_OMAP4)		+= $(omap-4-5-common)
-obj-$(CONFIG_SOC_OMAP5)			+= $(omap-4-5-common)
+obj-$(CONFIG_ARCH_OMAP4)		+= $(omap-4-5-common) $(smp-y)
+obj-$(CONFIG_SOC_OMAP5)			+= $(omap-4-5-common) $(smp-y)
 
 plus_sec := $(call as-instr,.arch_extension sec,+sec)
 AFLAGS_omap-headsmp.o			:=-Wa,-march=armv7-a$(plus_sec)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 6de7860..04c1165 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -112,13 +112,13 @@ static u8 omap3_beagle_version;
  */
 static struct {
 	int mmc1_gpio_wp;
-	int usb_pwr_level;
+	bool usb_pwr_level;	/* 0 - Active Low, 1 - Active High */
 	int dvi_pd_gpio;
 	int usr_button_gpio;
 	int mmc_caps;
 } beagle_config = {
 	.mmc1_gpio_wp = -EINVAL,
-	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
+	.usb_pwr_level = 0,
 	.dvi_pd_gpio = -EINVAL,
 	.usr_button_gpio = 4,
 	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
@@ -178,7 +178,7 @@ static void __init omap3_beagle_init_rev(void)
 	case 0:
 		printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
-		beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
+		beagle_config.usb_pwr_level = 1;
 		beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
 		break;
 	case 2:
diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c
index 1a88467..18ca61e 100644
--- a/arch/arm/mach-omap2/board-rx51-peripherals.c
+++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
@@ -73,11 +73,11 @@
 #define LIS302_IRQ1_GPIO 181
 #define LIS302_IRQ2_GPIO 180  /* Not yet in use */
 
-/* list all spi devices here */
+/* List all SPI devices here. Note that the list/probe order seems to matter! */
 enum {
 	RX51_SPI_WL1251,
-	RX51_SPI_MIPID,		/* LCD panel */
 	RX51_SPI_TSC2005,	/* Touch Controller */
+	RX51_SPI_MIPID,		/* LCD panel */
 };
 
 static struct wl12xx_platform_data wl1251_pdata;
diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c
index ed946df..6c4da12 100644
--- a/arch/arm/mach-omap2/gpmc.c
+++ b/arch/arm/mach-omap2/gpmc.c
@@ -1520,36 +1520,22 @@ static int gpmc_probe_dt(struct platform_device *pdev)
 		return ret;
 	}
 
-	for_each_node_by_name(child, "nand") {
-		ret = gpmc_probe_nand_child(pdev, child);
-		if (ret < 0) {
-			of_node_put(child);
-			return ret;
-		}
-	}
+	for_each_child_of_node(pdev->dev.of_node, child) {
 
-	for_each_node_by_name(child, "onenand") {
-		ret = gpmc_probe_onenand_child(pdev, child);
-		if (ret < 0) {
-			of_node_put(child);
-			return ret;
-		}
-	}
+		if (!child->name)
+			continue;
 
-	for_each_node_by_name(child, "nor") {
-		ret = gpmc_probe_generic_child(pdev, child);
-		if (ret < 0) {
-			of_node_put(child);
-			return ret;
-		}
-	}
+		if (of_node_cmp(child->name, "nand") == 0)
+			ret = gpmc_probe_nand_child(pdev, child);
+		else if (of_node_cmp(child->name, "onenand") == 0)
+			ret = gpmc_probe_onenand_child(pdev, child);
+		else if (of_node_cmp(child->name, "ethernet") == 0 ||
+			 of_node_cmp(child->name, "nor") == 0)
+			ret = gpmc_probe_generic_child(pdev, child);
 
-	for_each_node_by_name(child, "ethernet") {
-		ret = gpmc_probe_generic_child(pdev, child);
-		if (ret < 0) {
+		if (WARN(ret < 0, "%s: probing gpmc child %s failed\n",
+			 __func__, child->full_name))
 			of_node_put(child);
-			return ret;
-		}
 	}
 
 	return 0;
diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c
index 0f4c18e..1272c41 100644
--- a/arch/arm/mach-omap2/id.c
+++ b/arch/arm/mach-omap2/id.c
@@ -419,11 +419,15 @@ void __init omap3xxx_check_revision(void)
 			cpu_rev = "1.0";
 			break;
 		case 1:
-		/* FALLTHROUGH */
-		default:
 			omap_revision = AM335X_REV_ES2_0;
 			cpu_rev = "2.0";
 			break;
+		case 2:
+		/* FALLTHROUGH */
+		default:
+			omap_revision = AM335X_REV_ES2_1;
+			cpu_rev = "2.1";
+			break;
 		}
 		break;
 	case 0xb8f2:
@@ -644,13 +648,12 @@ void __init omap_soc_device_init(void)
 	soc_dev_attr->revision = soc_rev;
 
 	soc_dev = soc_device_register(soc_dev_attr);
-	if (IS_ERR_OR_NULL(soc_dev)) {
+	if (IS_ERR(soc_dev)) {
 		kfree(soc_dev_attr);
 		return;
 	}
 
 	parent = soc_device_to_device(soc_dev);
-	if (!IS_ERR_OR_NULL(parent))
-		device_create_file(parent, &omap_soc_attr);
+	device_create_file(parent, &omap_soc_attr);
 }
 #endif /* CONFIG_SOC_BUS */
diff --git a/arch/arm/mach-omap2/mux34xx.h b/arch/arm/mach-omap2/mux34xx.h
index 6543ebf..3f26d29 100644
--- a/arch/arm/mach-omap2/mux34xx.h
+++ b/arch/arm/mach-omap2/mux34xx.h
@@ -393,6 +393,10 @@
 #define OMAP3_CONTROL_PADCONF_SAD2D_SWAKEUP_OFFSET		0xa1c
 #define OMAP3_CONTROL_PADCONF_JTAG_RTCK_OFFSET			0xa1e
 #define OMAP3_CONTROL_PADCONF_JTAG_TDO_OFFSET			0xa20
+#define OMAP3_CONTROL_PADCONF_GPIO_127				0xa24
+#define OMAP3_CONTROL_PADCONF_GPIO_126				0xa26
+#define OMAP3_CONTROL_PADCONF_GPIO_128				0xa28
+#define OMAP3_CONTROL_PADCONF_GPIO_129				0xa2a
 
 #define OMAP3_CONTROL_PADCONF_MUX_SIZE				\
-		(OMAP3_CONTROL_PADCONF_JTAG_TDO_OFFSET + 0x2)
+		(OMAP3_CONTROL_PADCONF_GPIO_129 + 0x2)
diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c
index eeea4fa..e6d2307 100644
--- a/arch/arm/mach-omap2/omap_device.c
+++ b/arch/arm/mach-omap2/omap_device.c
@@ -876,4 +876,4 @@ static int __init omap_device_late_init(void)
 	bus_for_each_dev(&platform_bus_type, NULL, NULL, omap_device_late_idle);
 	return 0;
 }
-omap_late_initcall(omap_device_late_init);
+omap_late_initcall_sync(omap_device_late_init);
diff --git a/arch/arm/mach-omap2/soc.h b/arch/arm/mach-omap2/soc.h
index 18fdeeb..197cc16 100644
--- a/arch/arm/mach-omap2/soc.h
+++ b/arch/arm/mach-omap2/soc.h
@@ -396,6 +396,7 @@ IS_OMAP_TYPE(3430, 0x3430)
 #define AM335X_CLASS		0x33500033
 #define AM335X_REV_ES1_0	AM335X_CLASS
 #define AM335X_REV_ES2_0	(AM335X_CLASS | (0x1 << 8))
+#define AM335X_REV_ES2_1	(AM335X_CLASS | (0x2 << 8))
 
 #define OMAP443X_CLASS		0x44300044
 #define OMAP4430_REV_ES1_0	(OMAP443X_CLASS | (0x10 << 8))
@@ -496,6 +497,7 @@ level(__##fn);
 #define omap_subsys_initcall(fn)	omap_initcall(subsys_initcall, fn)
 #define omap_device_initcall(fn)	omap_initcall(device_initcall, fn)
 #define omap_late_initcall(fn)		omap_initcall(late_initcall, fn)
+#define omap_late_initcall_sync(fn)	omap_initcall(late_initcall_sync, fn)
 
 #endif	/* __ASSEMBLY__ */
 
diff --git a/arch/arm/mach-prima2/Kconfig b/arch/arm/mach-prima2/Kconfig
index 80ca974..6988b11 100644
--- a/arch/arm/mach-prima2/Kconfig
+++ b/arch/arm/mach-prima2/Kconfig
@@ -38,7 +38,7 @@ config ARCH_MARCO
 	select CPU_V7
 	select HAVE_ARM_SCU if SMP
 	select HAVE_SMP
-	select SMP_ON_UP
+	select SMP_ON_UP if SMP
 	help
           Support for CSR SiRFSoC ARM Cortex A9 Platform
 
diff --git a/arch/arm/mach-spear/spear13xx.c b/arch/arm/mach-spear/spear13xx.c
index 3621599..7aa6e8c 100644
--- a/arch/arm/mach-spear/spear13xx.c
+++ b/arch/arm/mach-spear/spear13xx.c
@@ -35,6 +35,8 @@ void __init spear13xx_l2x0_init(void)
 	 * write alloc and 'Full line of zero' options
 	 *
 	 */
+	if (!IS_ENABLED(CONFIG_CACHE_L2X0))
+		return;
 
 	writel_relaxed(0x06, VA_L2CC_BASE + L2X0_PREFETCH_CTRL);
 
diff --git a/arch/arm/mach-tegra/Kconfig b/arch/arm/mach-tegra/Kconfig
index 20c3b37..84d72fc 100644
--- a/arch/arm/mach-tegra/Kconfig
+++ b/arch/arm/mach-tegra/Kconfig
@@ -63,6 +63,7 @@ config ARCH_TEGRA_114_SOC
 	select ARM_ARCH_TIMER
 	select ARM_GIC
 	select ARM_L1_CACHE_SHIFT_6
+	select CPU_FREQ_TABLE if CPU_FREQ
 	select CPU_V7
 	select PINCTRL
 	select PINCTRL_TEGRA114
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index f66d7de..6a4387e 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -19,6 +19,8 @@ if ARCH_U8500
 config UX500_SOC_COMMON
 	bool
 	default y
+	select ABX500_CORE
+	select AB8500_CORE
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369 if SMP
 	select ARM_GIC
diff --git a/arch/arm/mach-ux500/board-mop500.c b/arch/arm/mach-ux500/board-mop500.c
index a15dd6b..3cd555a 100644
--- a/arch/arm/mach-ux500/board-mop500.c
+++ b/arch/arm/mach-ux500/board-mop500.c
@@ -403,8 +403,8 @@ static int mop500_prox_activate(struct device *dev)
 			"no regulator\n");
 		return PTR_ERR(prox_regulator);
 	}
-	regulator_enable(prox_regulator);
-	return 0;
+
+	return regulator_enable(prox_regulator);
 }
 
 static void mop500_prox_deactivate(struct device *dev)
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c
index 995928b..e90b5ab 100644
--- a/arch/arm/mach-ux500/cpu-db8500.c
+++ b/arch/arm/mach-ux500/cpu-db8500.c
@@ -191,7 +191,7 @@ static const char *db8500_read_soc_id(void)
 	/* Throw these device-specific numbers into the entropy pool */
 	add_device_randomness(uid, 0x14);
 	return kasprintf(GFP_KERNEL, "%08x%08x%08x%08x%08x",
-			 readl((u32 *)uid+1),
+			 readl((u32 *)uid+0),
 			 readl((u32 *)uid+1), readl((u32 *)uid+2),
 			 readl((u32 *)uid+3), readl((u32 *)uid+4));
 }
diff --git a/drivers/video/Kconfig b/drivers/video/Kconfig
index 1534cf3..d71d60f 100644
--- a/drivers/video/Kconfig
+++ b/drivers/video/Kconfig
@@ -2429,7 +2429,7 @@ config FB_MXS
 	select FB_CFB_COPYAREA
 	select FB_CFB_IMAGEBLIT
 	select FB_MODE_HELPERS
-	select OF_VIDEOMODE
+	select VIDEOMODE_HELPERS
 	help
 	  Framebuffer support for the MXS SoC.
 
diff --git a/drivers/video/mxsfb.c b/drivers/video/mxsfb.c
index 1b2c26d..21223d4 100644
--- a/drivers/video/mxsfb.c
+++ b/drivers/video/mxsfb.c
@@ -42,7 +42,6 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/of_device.h>
-#include <video/of_display_timing.h>
 #include <linux/platform_device.h>
 #include <linux/clk.h>
 #include <linux/dma-mapping.h>
@@ -50,6 +49,7 @@
 #include <linux/pinctrl/consumer.h>
 #include <linux/fb.h>
 #include <linux/regulator/consumer.h>
+#include <video/of_display_timing.h>
 #include <video/videomode.h>
 
 #define REG_SET	4
@@ -777,16 +777,16 @@ static int mxsfb_init_fbinfo_dt(struct mxsfb_info *host)
 		struct videomode vm;
 		struct fb_videomode fb_vm;
 
-		ret = videomode_from_timing(timings, &vm, i);
+		ret = videomode_from_timings(timings, &vm, i);
 		if (ret < 0)
 			goto put_timings_node;
 		ret = fb_videomode_from_videomode(&vm, &fb_vm);
 		if (ret < 0)
 			goto put_timings_node;
 
-		if (vm.data_flags & DISPLAY_FLAGS_DE_HIGH)
+		if (vm.flags & DISPLAY_FLAGS_DE_HIGH)
 			host->sync |= MXSFB_SYNC_DATA_ENABLE_HIGH_ACT;
-		if (vm.data_flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE)
+		if (vm.flags & DISPLAY_FLAGS_PIXDATA_NEGEDGE)
 			host->sync |= MXSFB_SYNC_DOTCLK_FALLING_ACT;
 		fb_add_videomode(&fb_vm, &fb_info->modelist);
 	}
diff --git a/include/linux/platform_data/imx-iram.h b/include/linux/platform_data/imx-iram.h
deleted file mode 100644
index 022690c..0000000
--- a/include/linux/platform_data/imx-iram.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * Copyright (C) 2010 Freescale Semiconductor, Inc. All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version 2
- * of the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301, USA.
- */
-#include <linux/errno.h>
-
-#ifdef CONFIG_IRAM_ALLOC
-
-int __init iram_init(unsigned long base, unsigned long size);
-void __iomem *iram_alloc(unsigned int size, unsigned long *dma_addr);
-void iram_free(unsigned long dma_addr, unsigned int size);
-
-#else
-
-static inline int __init iram_init(unsigned long base, unsigned long size)
-{
-	return -ENOMEM;
-}
-
-static inline void __iomem *iram_alloc(unsigned int size, unsigned long *dma_addr)
-{
-	return NULL;
-}
-
-static inline void iram_free(unsigned long base, unsigned long size) {}
-
-#endif