diff options
Diffstat (limited to 'x11vnc/help.c')
| -rw-r--r-- | x11vnc/help.c | 84 |
1 files changed, 52 insertions, 32 deletions
diff --git a/x11vnc/help.c b/x11vnc/help.c index 55ad36a..c23112c 100644 --- a/x11vnc/help.c +++ b/x11vnc/help.c @@ -136,7 +136,7 @@ void print_help(int mode) { " The default is to start probing at 5900. Use this to\n" " stay away from other VNC servers near 5900.\n" "\n" -"-rfbport str The VNC port to listen on (a libvncserver option), e.g.\n" +"-rfbport str The VNC port to listen on (a LibVNCServer option), e.g.\n" " 5900, 5901, etc. If specified as \"-rfbport PROMPT\"\n" " then the x11vnc -gui is used to prompt the user to\n" " enter the port number.\n" @@ -144,20 +144,37 @@ void print_help(int mode) { #if X11VNC_IPV6 "-6 IPv6 listening support. In addition to IPv4, the\n" " IPv6 address is listened on for incoming connections.\n" -" The same port as IPv4 is used to listen. If you have\n" -" trouble compiling for this mode, set -DX11VNC_IPV6=0\n" -" in CPPFLAGS when configuring.\n" +" The same port as IPv4 is used.\n" "\n" -" Currently, the machine may need to have some IPv4\n" -" support, at the least for the loopback interface, for\n" -" everything to work correctly. However for most usage\n" -" modes IPv4 support is not required.\n" +#if X11VNC_LISTEN6 +" NOTE: This x11vnc binary was compiled to have the\n" +" \"-6\" IPv6 listening mode ENABLED by default (CPPFLAGS\n" +" -DX11VNC_LISTEN6=1). So to disable IPv6 listening mode\n" +" you MUST supply the \"-no6\" option (see below.)\n" +#else +" NOTE: This x11vnc binary was compiled to have\n" +" the \"-6\" IPv6 listening mode DISABLED by default\n" +" (CPPFLAGS -DX11VNC_LISTEN6=0).\n" +#endif "\n" -" The -6 mode works for both normal connections and\n" +" The \"-6\" mode works for both normal connections and\n" " -ssl encrypted ones. Nearly everything is supported\n" " for the IPv6 case, but there are a few exceptions.\n" " See -stunnel for its IPv6 support.\n" "\n" +" Currently, for absolutely everything to work correctly\n" +" the machine may need to have some IPv4 support, at the\n" +" least for the loopback interface. However, for nearly\n" +" all usage modes no IPv4 support is required. See -nopiv4.\n" +"\n" +" If you have trouble compiling or running in IPv6 mode,\n" +" set -DX11VNC_IPV6=0 in CPPFLAGS when configuring to\n" +" disable IPv6 support.\n" +"\n" +"-no6 Disable IPv6 listening support (only useful if the\n" +" \"-6\" mode is compiled in to be the default; see the\n" +" X11VNC_LISTEN6 description above under \"-6\".)\n" +"\n" "-noipv6 Do not try to use IPv6 for any listening or connecting\n" " sockets. This includes both the listening service\n" " port(s) and outgoing connections from -connect,\n" @@ -522,7 +539,7 @@ void print_help(int mode) { " Also, tightfilexfer is disabled in -unixpw mode.\n" "\n" "-ultrafilexfer Note: to enable UltraVNC filetransfer and to get it to\n" -" work you probably need to supply these libvncserver\n" +" work you probably need to supply these LibVNCServer\n" " options: \"-rfbversion 3.6 -permitfiletransfer\"\n" " \"-ultrafilexfer\" is an alias for this combination.\n" "\n" @@ -635,6 +652,8 @@ void print_help(int mode) { "-connect_or_exit str As with -connect, except if none of the reverse\n" " connections succeed, then x11vnc shuts down immediately\n" "\n" +" An easier to type alias for this option is '-coe'\n" +"\n" " By the way, if you do not want x11vnc to listen on\n" " ANY interface use -rfbport 0 which is handy for the\n" " -connect_or_exit mode.\n" @@ -725,7 +744,7 @@ void print_help(int mode) { " the comma separated list of hostnames or IP addresses.\n" " Can also be a numerical IP prefix, e.g. \"192.168.100.\"\n" " to match a simple subnet, for more control build\n" -" libvncserver with libwrap support (See the FAQ). If the\n" +" LibVNCServer with libwrap support (See the FAQ). If the\n" " list contains a \"/\" it instead is a interpreted\n" " as a file containing addresses or prefixes that is\n" " re-read each time a new client connects. Lines can be\n" @@ -759,10 +778,11 @@ void print_help(int mode) { " implies the IPv6 loopback address '::1' as well.\n" "\n" #if X11VNC_IPV6 -"-listen6 str When in IPv6 listen mode \"-6\", only listen on the\n" -" network interface with address \"str\". It currently\n" -" does not work for link scope addresses or non-numeric\n" -" hostname strings.\n" +"-listen6 str When in IPv6 listen mode \"-6\", listen only on the\n" +" network interface with address \"str\". It also works\n" +" for link scope addresses (fe80::219:dbff:fee5:3f92%%eth0)\n" +" and IPv6 hostname strings (e.g. ipv6.google.com.)\n" +" Use LibVNCServer -listen option for the IPv4 interface.\n" "\n" #endif "-nolookup Do not use gethostbyname() or gethostbyaddr() to look up\n" @@ -822,7 +842,7 @@ void print_help(int mode) { "-viewpasswd string Supply a 2nd password for view-only logins. The -passwd\n" " (full-access) password must also be supplied.\n" "\n" -"-passwdfile filename Specify the libvncserver password via the first line\n" +"-passwdfile filename Specify the LibVNCServer password via the first line\n" " of the file \"filename\" (instead of via -passwd on\n" " the command line where others might see it via ps(1)).\n" "\n" @@ -2499,10 +2519,10 @@ void print_help(int mode) { " the network (i.e. you just want the single VNC/HTTPS\n" " port, e.g. 5900, open for connections) then specify the\n" " option -env X11VNC_HTTP_LISTEN_LOCALHOST=1 This way\n" -" the connection to the libvncserver httpd server will\n" +" the connection to the LibVNCServer httpd server will\n" " only be available on localhost (note that in -ssl mode,\n" " HTTPS requests are redirected from SSL to the non-SSL\n" -" libvncserver HTTP server.)\n" +" LibVNCServer HTTP server.)\n" "\n" "-http_oneport For UN-encrypted connections mode (i.e. no -ssl,\n" " -stunnel, or -enc options), allow the Java VNC Viewer\n" @@ -2536,7 +2556,7 @@ void print_help(int mode) { "\n" " Note that the -env X11VNC_HTTP_LISTEN_LOCALHOST=1\n" " option described above under -httpsredir applies for\n" -" the libvncserver httpd server in all cases (ssl or not.)\n" +" the LibVNCServer httpd server in all cases (ssl or not.)\n" "\n" "-ssh user@host:disp Create a remote listening port on machine \"host\"\n" " via a SSH tunnel using the -R rport:localhost:lport\n" @@ -2551,7 +2571,7 @@ void print_help(int mode) { " username differs from the current one.\n" "\n" " By default the remote sshd is usually configured to\n" -" only listen on localhost for rport, so the viewer may\n" +" listen only on localhost for rport, so the viewer may\n" " need to ssh -L redir to \"host\" as well (See SSVNC to\n" " automate this). The sshd setting GatewayPorts enables\n" " listening on all interfaces for rport; viewers can\n" @@ -2884,7 +2904,7 @@ void print_help(int mode) { " where you resize often. It is best to be viewing with a\n" " vncviewer that supports the NewFBSize encoding, since it\n" " knows how to react to screen size changes. Otherwise,\n" -" libvncserver tries to do so something reasonable for\n" +" LibVNCServer tries to do so something reasonable for\n" " viewers that cannot do this (portions of the screen\n" " may be clipped, unused, etc).\n" "\n" @@ -3327,7 +3347,7 @@ void print_help(int mode) { " alpha factor. (useful for light colored semi-transparent\n" " cursors).\n" "-noalphablend In XFIXES mode do not send cursor alpha channel data\n" -" to libvncserver. The default is to send it. The\n" +" to LibVNCServer. The default is to send it. The\n" " alphablend effect will only be visible in -nocursorshape\n" " mode or for clients with cursorshapeupdates turned\n" " off. (However there is a hack for 32bpp with depth 24,\n" @@ -3975,9 +3995,9 @@ void print_help(int mode) { " to really throttle down the screen polls (i.e. sleep\n" " for about 1.5 secs). Use 0 to disable. Default: %d\n" "\n" -"-readtimeout n Set libvncserver rfbMaxClientWait to n seconds. On\n" +"-readtimeout n Set LibVNCServer rfbMaxClientWait to n seconds. On\n" " slow links that take a long time to paint the first\n" -" screen libvncserver may hit the timeout and drop the\n" +" screen LibVNCServer may hit the timeout and drop the\n" " connection. Default: %d seconds.\n" "-ping n Send a 1x1 framebuffer update to all clients every n\n" " seconds (e.g. to try to keep a network connection alive)\n" @@ -4046,7 +4066,7 @@ void print_help(int mode) { " skip powering off the monitor.\n" "\n" "-noultraext Disable the following UltraVNC extensions: SingleWindow\n" -" and ServerInput. The others managed by libvncserver\n" +" and ServerInput. The others managed by LibVNCServer\n" " (textchat, 1/n scaling, rfbEncodingUltra) are not.\n" "\n" "-chatwindow Place a local UltraVNC chat window on the X11 display\n" @@ -4100,12 +4120,12 @@ void print_help(int mode) { " (perhaps useful on a slow machine).\n" "\n" "-sigpipe string Broken pipe (SIGPIPE) handling. \"string\" can be\n" -" \"ignore\" or \"exit\". For \"ignore\" libvncserver\n" +" \"ignore\" or \"exit\". For \"ignore\" LibVNCServer\n" " will handle the abrupt loss of a client and continue,\n" " for \"exit\" x11vnc will cleanup and exit at the 1st\n" " broken connection.\n" "\n" -" This option is not really needed since libvncserver\n" +" This option is not really needed since LibVNCServer\n" " is doing the correct thing now for quite some time.\n" " However, for convenience you can use it to ignore other\n" " signals, e.g. \"-sigpipe ignore:HUP,INT,TERM\" in case\n" @@ -4115,7 +4135,7 @@ void print_help(int mode) { " for this option if you don't like the 'pipe'. Example:\n" " -sig ignore:INT,TERM,exit:USR1\n" "\n" -"-threads Whether or not to use the threaded libvncserver\n" +"-threads Whether or not to use the threaded LibVNCServer\n" "-nothreads algorithm [rfbRunEventLoop] if libpthread is available.\n" " In this mode new threads (one for input and one\n" " for output) are created to handle each new client.\n" @@ -4374,7 +4394,7 @@ void print_help(int mode) { " view and possibly interact with the Linux text/graphics\n" " console (i.e. not X11 XFree86/Xorg)\n" "\n" -" Note: If the libvncserver LinuxVNC program is on your\n" +" Note: If the LibVNCServer LinuxVNC program is on your\n" " system you may want to use that instead of the following\n" " method because it will be faster and more accurate\n" " for the Linux text console and includes mouse support.\n" @@ -5158,7 +5178,7 @@ void print_help(int mode) { " uinput_thresh:n set uinput_thresh to n.\n" " uinput_reset:n set uinput_reset to n ms.\n" " uinput_always:n set uinput_always to 1/0.\n" -" progressive:n set libvncserver -progressive slice\n" +" progressive:n set LibVNCServer -progressive slice\n" " height parameter to n.\n" " desktop:str set -desktop name to str for new clients.\n" " rfbport:n set -rfbport to n.\n" @@ -5540,7 +5560,7 @@ void print_help(int mode) { "\n" "%s\n" "\n" -"These options are passed to libvncserver:\n" +"These options are passed to LibVNCServer:\n" "\n" ; /* have both our help and rfbUsage to stdout for more(1), etc. */ @@ -5571,7 +5591,7 @@ void print_help(int mode) { } p = strtok(NULL, "\n"); } - fprintf(stderr, "\n\nlibvncserver options:\n"); + fprintf(stderr, "\n\nLibVNCServer options:\n"); rfbUsage(); fprintf(stderr, "\n"); exit(1); |
