summaryrefslogtreecommitdiffstats
path: root/programmer.h
Commit message (Collapse)AuthorAgeFilesLines
* Add new programmer for SPI EEPROMs attached to Intel 82580 NICsRicardo Ribalda Delgado2014-07-281-0/+9
| | | | | | | | | | | | | | | | | This patch lets you read and write the EEPROM on 82580-based gigabit NIC cards. So far it has been tested on copper NICs only, but other variants employing this controller should work too. It is a nice substitution for the official eeupdate tool. Speed is quite decent: less than 4 seconds for erases or writes of 32 kB. Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Corresponding to flashrom svn r1832. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Rename programmer registration functionsCarl-Daniel Hailfinger2014-07-191-16/+16
| | | | | | | | | | | | Register_programmer suggests that we register a programmer. However, that function registers a master for a given bus type, and a programmer may support multiple masters (e.g. SPI, FWH). Rename a few other functions to be more consistent. Corresponding to flashrom svn r1831. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add selfcheck_board_enables()Stefan Tauner2014-06-121-0/+1
| | | | | | | | | | | | Check for NULL termination of the array, that each board has the two main PCI ID sets defined, that coreboot vendor and model fields are either both set or unset, and that at least either an enable function or a max decode size is available. Corresponding to flashrom svn r1821. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Move global io_base_addr into compilation unitsStefan Tauner2014-06-011-2/+1
| | | | | | | Corresponding to flashrom svn r1813. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Add IT8212F as programmerStefan Tauner2014-06-011-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | This PCI PATA controller can use 3V parallel flash up to 128 kB. My card was identified as: PCI 1283:8212, subsystem 1283:0001. and labelled as: Innovision Multimedia LTD. EIO ATA133 RAID (DM-8401 Ver A) This particular card did not require setting of any GPIO signals to enable flash writing. My card has Pm39LV512 in PLCC32 package without socket. Rebased by Stefan (automatic cleanup, some PCI changes, changed enable bit handling). Committed with test state NT because the rebased version was not tested on real hardware (yet). Binary file (standard input) matches Corresponding to flashrom svn r1812.
* Add VIA VT6421A LPC programmer driverJonathan Kollasch2014-06-011-0/+10
| | | | | | | | | | | | | | | Due to the mysterious address handling of this chip the user can specify a base address with the offset parameter, e.g.: flashrom -p atavia:offset=0xFFF00000 Thanks to Idwer Vollering for his iterative testing of this code, as well as to Martijn Bastiaan who did the last tests before merging. Corresponding to flashrom svn r1809. Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* sbxxx: Add support for new AMD SPI controllerWei Hu2014-05-161-0/+1
| | | | | | | | | | | | | | This patch adds support for the "SPI 100" SPI engine in Yangtze FCHs (found in Kabini and Temash). Tested reading/writing on ASRock IMB-A180 and PC Engines' APU board. Corresponding to flashrom svn r1794. Signed-off-by: Wei Hu <wei@aristanetworks.com> Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add 'const' keyword to chip write and other function prototypesMark Marshall2014-05-091-9/+9
| | | | | | | | | | Inspired by and mostly based on a patch Corresponding to flashrom svn r1789. Signed-off-by: Mark Marshall <mark.marshall@omicron.at> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Make delay values unsignedStefan Tauner2014-05-021-5/+5
| | | | | | | | | | | | | | | There is no reason for negative delays in our use cases: - We don't need it (to work around any quirks). - sleep() (POSIX) uses an unsigned argument. - usleep() (POSIX) uses an unsigned argument. - Sleep() (Windows) uses an unsigned argument. Change all callees as well (without any complications). Corresponding to flashrom svn r1782. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Clean up physmap, fix unaligned mapping problemsCarl-Daniel Hailfinger2014-03-051-1/+2
| | | | | | | | | | | | Convert all physmaps in dmi.c to use aligned readonly maps. Convert all physmaps in cbtable.c to use unaligned readonly maps. Make physunmap() a generic architecture-independent wrapper. Add physunmap_unaligned() to complement physmap*_unaligned(). Corresponding to flashrom svn r1765. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Refactor Intel Chipset EnablesStefan Tauner2013-10-251-6/+6
| | | | | | | | | | | | | | | | | | | | | - Combine enable_flash_ich_4e() and enable_flash_ich_dc() to enable_flash_ich_fwh(). - Remove unjustified (chipset) name parameters from various enable_flash_ich* functions. - Make Poulsbo and Tunnel Creek use generic enables by refining existing functions to work with them, including everything in ichspi.c. - Refactor enable_flash_ich_fwh_decode() to be called unconditionally for all chipsets. - Add support for Intel Atom Centerton (S12x0). - Recombine ICH2/3/4/5 to CHIPSET_ICH2345 because we treat them equally anyway. - Move spibar handling out of ich_init_spi() into enable_flash_ich_spi() - Various small cleanups. Corresponding to flashrom svn r1761. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Use ich_generation parameter in enable functions prior to ICH7Stefan Tauner2013-09-141-2/+7
| | | | | | | | | Follow the style used from ICH7 onwards to pass ich_generation parameter to lower-level functions on older ICH chipsets too. Binary file (standard input) matches Corresponding to flashrom svn r1747.
* Remove exit call and mayfail parameter from physmap_common()Stefan Tauner2013-09-141-1/+1
| | | | | | | | | | | | | The only call path where exit was reached was from physmap functions. Callers of physmap() et al. which were not prepared to handle ERROR_PTR return values have been adjusted. physmap_try_ro() has been renamed to physmap_ro() and physmap_common() slightly refactored due to the now removed *FAIL parameters. Binary file (standard input) matches Corresponding to flashrom svn r1745.
* Add an internal DMI decoderSean Nelson2013-09-111-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Previously we had to rely on dmidecode to decode the DMI/SMBIOS table. This patch integrates a DMI decoder into flashrom. The old behavior of calling dmidecode can be brought back by using CONFIG_INTERNAL_DMI=no. Significant portions of this patch were taken from dmidecode, hence add its authors to the copyright notice (dmidecode is also GPL2+). We do a few things differently though. First of all we do more bounds checking to prevent accessing unmapped memory. We do not support disovery via EFI (yet), but memory scanning only. We handle the chassis-type lock bit correctly which dmidecode did not for a long while. The API to the rest of flashrom remains stable, but the output changes slightly. To share as much code as possible (which actually is not much), i have added dmi_fill methods that get called in dmi_init. They are reponsible to fill the dmi_strings array and setting the is_laptop variable. After it is called, dmi_init prints all dmi_strings. Previously the strings were printed in the order they were discovered, followed by the chassis-type, which is now output earlier (in dmi_fill). Because DJGPP does not support strnlen a simple implementation was added for it. This is still only available on x86; actually it is not even compiled in for other architectures at all anymore. Tested-by: Maciej Pijanka <maciej.pijanka@gmail.com> Tested-by: Idwer Vollering <vidwer@gmail.com> Corresponding to flashrom svn r1735. Signed-off-by: Sean Nelson <audiohacked@gmail.com> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Get rid of sp_die()Stefan Tauner2013-08-241-1/+0
| | | | | | | | | | | | | | - Add return values to sp_flush_stream(), sp_pass_writen(), sp_execute_opbuf(), sp_execute_opbuf_noflush(), sp_check_opbuf_usage(), sp_do_read_n(). - Use those return values to propagate errors instead of exiting. In some places this has to wait for core API changes (error handling for chip_readb, chip_readn, chip_write) hence comments are added instead. Corresponding to flashrom svn r1719. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Introduce serialport_config()Stefan Tauner2013-08-231-0/+1
| | | | | | | | | | This allows to easily reconfigure a serial port as needed in the Bus Pirate speedup patch. Corresponding to flashrom svn r1717. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Automatically unmap physmap()sStefan Tauner2013-08-141-0/+1
| | | | | | | | | | | | Similarly to the previous PCI self-clean up patch this one allows to get rid of a huge number of programmer shutdown functions and makes introducing bugs harder. It adds a new function rphysmap() that takes care of unmapping at shutdown. Callers are changed where it makes sense. Corresponding to flashrom svn r1714. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Add a bunch of new/tested stuff and various small changes 19Stefan Tauner2013-08-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tested mainboards: OK: - ASUS P8H77-V LE http://www.flashrom.org/pipermail/flashrom/2013-June/011127.html - HP Pegatron IPMEL-AE (Evans-GL6) Reported by Idwer on IRC - MSI MS-7379 (G31M) http://paste.flashrom.org/view.php?id=1726 - MSI MS-7816 (H87-G43) http://www.flashrom.org/pipermail/flashrom/2013-July/011349.html - MSI MS-9830 (IM-945GSE-A, A9830IMS) http://paste.flashrom.org/view.php?id=1730 - Supermicro X8SAX http://paste.flashrom.org/view.php?id=1717 NOT OK: - Intel D2700MUD http://paste.flashrom.org/view.php?id=1723 - Intel DQ45CB http://www.flashrom.org/pipermail/flashrom/2013-August/011369.html Chipsets: - Add PCI ID for Intel's Coleto Creek. - Mark Intel H87 (0x8c4a) as OK. http://www.flashrom.org/pipermail/flashrom/2013-July/011349.html Miscellaneous: - ichspi: Fix printing address ranges if space is divided by FPB. - Tiny other stuff. Corresponding to flashrom svn r1709. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* sbxxx: Handle active IMCs in AMD chipsetsRudolf Marek2013-07-251-0/+3
| | | | | | | | | | | | Detect and temporarily disable the IMC while accessing the flash. Disable writes on default, but allow the user to enforce it. Corresponding to flashrom svn r1704. Signed-off-by: Rudolf Marek <r.marek@assembler.cz> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: David Hendricks <dhendrix@google.com>
* Uintptr_t-ify map_flash_region functionsStefan Tauner2013-07-171-5/+5
| | | | | | | | | | | | | | | | | | | Unsigned long is not the right type for manipulating pointer values. Since C99 there are suitable unsigned and signed types available, namely uintptr_t and intptr_t respectively. Use them in functions assigned to programmers' map_flash_region fields and their callers where applicable. This patch also changes the display width of all associated address values in physmap.c to 16/8 hex characters depending on the actual size by introducing a macro PRIxPTR_WIDTH and exploiting printf's * field width specifier. Corresponding to flashrom svn r1701. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Usleep() is not found in all versions of MinGW, use Sleep() on WindowsMaksim Kuleshov2013-04-051-0/+1
| | | | | | | | | | Handle long sleeps on non-Windows correctly. Corresponding to flashrom svn r1667. Signed-off-by: Maksim Kuleshov <mmcx@mail.ru> Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Introduce serialport_write_nonblock()Stefan Tauner2013-04-011-0/+1
| | | | | | | | | | | | | It seems useful to have a generic and platform-independent method to read and write to a serial port without blocking. This is the write part. This allows to get rid of the explicit temporary disabling of blocking I/O in serprog's sp_synchronize(). Corresponding to flashrom svn r1662. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Replace sp_sync_read_timeout() with serialport_read_nonblock()Stefan Tauner2013-04-011-0/+1
| | | | | | | | | | | | | | | It seems useful to have a generic and platform-independent method to read and write to a serial port without blocking. This is the read part. It stores the current blocking properties before disabling blocking and restores them after reading. The timeout is implemented as previously by retrying every millisecond until the timeout is reached or enough characters are available. Corresponding to flashrom svn r1661. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add Altera USB-Blaster SPI programmerJames Laird2013-03-271-0/+12
| | | | | | | | | | | Adds support for the Altera USB-Blaster programming dongle in Active Serial (AS) mode. Tested on both original product and a clone dongle. Binary file (standard input) matches Corresponding to flashrom svn r1658. Signed-off-by: James Laird <jhl@mafipulation.org>
* Add support for Intel Lynx Point low-power and WellsburgDuncan Laurie2013-03-151-1/+3
| | | | | | | | | | | | | | New IDs taken from Intel's patches for the Linux kernel. Also, refine original Lynx Point naming etc. Based on the chromiumos patch Change-Id: I303a05baa80e4449e70d20adf78ebc7128b88d8e Corresponding to flashrom svn r1656. Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Decouple BAR reading from pci device init, handle errors gracefullyCarl-Daniel Hailfinger2013-01-051-18/+18
| | | | | | | | | Pcidev_init() now returns struct pci_device * instead of a BAR stored in PCI config space. This allows for real error checking instead of having exit(1) everywhere in pcidev.c. Binary file (standard input) matches Corresponding to flashrom svn r1644.
* Unify PCI init and let pcidev clean itself upStefan Tauner2013-01-041-0/+1
| | | | | | | | | | | | | | | | | | | Previously the internal programmer used its own code to initialize pcilib. This patch extracts the common code from the internal programmer and pcidev_init() into pcidev_init_common(). This fixes the non-existent PCI cleanup of the internal programmer and adds an additional safety by checking for an already existing PCI context. We got a nice shutdown function registration infrastructure, but did not use it very wisely. Instead we added shutdown functions to a myriad of programmers unnecessarily. In this patch we get rid of those that do only call pci_cleanup(pacc) by adding a shutdown function the pcidev.c itself that gets registered by pcidev_init(). Corresponding to flashrom svn r1642. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Constify parameters and globalsNico Huber2012-12-301-1/+1
| | | | | | | | | | | This makes some stuff const (partially to get a more convenient libflashrom interface). Corresponding to flashrom svn r1639. Signed-off-by: Nico Huber <nico.huber@secunet.com> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Unify usbdev_status and pcidev_status into dev_entryStefan Tauner2012-12-271-37/+22
| | | | | | | | | | | | | | | | | | | Once upon a time usbdev_status was created for the ft2232 programmer. Its IDs are semantically different to pcidev_status because they indicate USB instead of PCI IDs, but apart from that both data structures are equal. This change makes life easier for everything involved in handling and printing the status of devices that is noted in those structures by combining them into dev_entry. It is still possible to distinguish between PCI and USB devices indirectly by using the struct programmer's type field. Also, add a programmer column to the PCI and USB devices lists. Corresponding to flashrom svn r1632. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Refactor PCI and USB device status printingStefan Tauner2012-12-271-14/+27
| | | | | | | | | | | | | | | | | To be able to get rid of lots of #ifdefs and centralize programmer-specific data more... - introduce two new fields to struct programmer_entry, namely enum type (OTHER, USB, PCI) and union devs (pcidev_status, usbdev_status or char *note). - use those fields to generate device listings in print.c and print_wiki.c. Bonus: add printing of USB devices to print_wiki.c and count supported PCI and USB devices. Corresponding to flashrom svn r1631. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Add general programmer sanity checksStefan Tauner2012-12-261-3/+1
| | | | | | | | | And remove the completely unused vendor field. Corresponding to flashrom svn r1630. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Fix flashrom running on boards with corebootStefan Tauner2012-09-241-1/+1
| | | | | | | | | | | | | | In r1577 we removed the discrimination of coreboot IDs and user-specified mainboards. The problem is that the board enable code required to find a board enable if either of these model strings were set. Therefore boards running coreboot that do not need a board enable failed to execute flashrom since then. This patch fixes this by handling coreboot IDs and user-supplied IDs differently again. Corresponding to flashrom svn r1605. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Idwer Vollering <vidwer@gmail.com>
* Fix compilation with MinGWStefan Tauner2012-09-011-0/+2
| | | | | | | | | | This was broken since r1557 when we got rid of some exit calls, but returned -1 instead which is not a valid HANDLE value. Corresponding to flashrom svn r1591. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Idwer Vollering <vidwer@gmail.com>
* Make struct flashchip a field in struct flashctx instead of a complete copyCarl-Daniel Hailfinger2012-08-251-1/+1
| | | | | | | | | | | | All the driver conversion work and cleanup has been done by Stefan. flashrom.c and cli_classic.c are a joint work of Stefan and Carl-Daniel. Corresponding to flashrom svn r1579. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Fix VIA VX*** supportHelge Wagner2012-08-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Helge Wagner's patch that added VIA VX900 chipset support made me look closer at the datasheets which led to some concise documentation about newer VIA chipsets: http://flashrom.org/VIA Based on that this patch adds full support for VX800/VX820, VX855/VX875 and VX900, including SPI and LPC. VT8237S was not changed (SPI support only) because there is no public datasheet and it is not clear how to distinguish between LPC and SPI strapping and investigations in (NDAed) documents have not brought up anything conclusively. enable_flash_vt823x could probably be enhanced too due to various ignored LPC options of the chipset. Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Corresponding to flashrom svn r1578. Signed-off-by: Helge Wagner <Helge.Wagner@ge.com> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Refactor the -p internal:mainboard handlingStefan Tauner2012-08-201-6/+4
| | | | | | | | | | | | | | | | This patch gets rid of some global variables and makes lots of bits along the code path that control the board enable execution more generic and clearer. From now on flashrom aborts on a few more occasions that should be safer for the user. For example it aborts if the enable function for the specified mainboard (enable) can not be found. Parts of the board_match_cbname refactoring were done by Carl-Daniel. Corresponding to flashrom svn r1577. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Move show_id to where it belongsStefan Tauner2012-08-111-3/+1
| | | | | | | | | And remove the unused force parameter. Corresponding to flashrom svn r1569. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Portability fixes and cleanupsCarl-Daniel Hailfinger2012-08-091-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move Mac OS X IOKit/DirectHW availability checks in the Makefile from compiler check to pciutils check. Print the compiler error messages for feature detection. Add DOS libpci in the Makefile includes only if a PCI-based programmer was requested. Restrict mmap usage in ich_descriptors_tool to Unix style systems. Build ich_descriptors_tool with the correct .exe extension on DOS/Windows. Build ich_descriptors_tool by default on x86. (Patch by Stefan Tauner) Print the Windows version instead of "unknown machine" on Windows. Don't #define our own __DARWIN__, use the standard OS X detection method. Update the README. Add more generated files to svn:ignore Corresponding to flashrom svn r1567. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Introduce enum test_stateStefan Tauner2012-07-281-5/+5
| | | | | | | | | | | | | | | | Previously boards in the wiki were tagged either as working or as known bad. But we added support to various boards via board enables that were then never tested because the owners have not reported back. This can now be tagged with NT and is shown appropriately. Also, the underlying data structure indicating state was converted from macros to an enum while preserving original integer values and is used for programmers and chipsets too. Corresponding to flashrom svn r1555. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Automatically release I/O permissions on shutdownCarl-Daniel Hailfinger2012-07-211-2/+1
| | | | | | | | | | | | | | | | | Get_io_perms() is renamed to rget_io_perms() and automatically registers a function to release I/O permissions on shutdown. Actually release I/O permissions on Solaris and iopl()-supporting operating systems like Linux. This patch fixes quite a few programmers which forgot to release I/O permissions on shutdown, and it simplifies the shutdown and error handling code for all others. Do not call exit(1) if I/O permissions are denied and return an error Binary file (standard input) matches Corresponding to flashrom svn r1551.
* Hide hwaccess.h from public APIPatrick Georgi2012-07-201-0/+2
| | | | | | | | | | | | | Move hwaccess.h #include from flash.h to individual drivers. libflashrom users need flash.h, but they do not care about hwaccess.h and should not see its definitions because they may conflict with other hardware access functions and #defines used by the libflashrom user. Corresponding to flashrom svn r1549. Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Check vendor_id for PCI based external programmersCarl-Daniel Hailfinger2012-07-161-1/+1
| | | | | | | | | | | | | | Restructure PCI device detection code. Rename pcidev_validate to pcidev_readbar. Note: Slight changes in behaviour are possible, especially on dual/quad chip NICs which appear as more than one PCI device. Found devices are no longer printed at _pinfo level, but rather at _pdbg level. Corresponding to flashrom svn r1548. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
* Let the programmer driver decide how to do AAI transfersNico Huber2012-06-151-0/+2
| | | | | | | | | | | | | | | | Currently spi_aai_write() is implemented without an abstraction mechanism for the programmer driver. This adds another function pointer 'write_aai' to struct spi_programmer, which is set to default_spi_write_aai (renamed spi_aai_write) for all programmers for now. A patch which utilises this abstraction in the dediprog driver will follow. Corresponding to flashrom svn r1543. Signed-off-by: Nico Huber <nico.huber@secunet.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Add Winbond W836xx SuperI/O detectionCarl-Daniel Hailfinger2012-05-061-0/+2
| | | | | | | | | | | | Add ITE IT8707F/IT8710F detection. Note that we autodetect those chips, but we don't handle their flash translation features automatically yet. Corresponding to flashrom svn r1533. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
* Add serial port bitbanging codeVirgil-Adrian Teaca2012-04-301-1/+39
| | | | | | | | | | | This adds the pony_spi driver which supports the SI_Prog adapter, which is commonly used for SPI chips with PonyProg 2000, and a custom adapter called "SERBANG" which differs in the logic of two pins. Corresponding to flashrom svn r1525. Signed-off-by: Virgil-Adrian Teaca <darkstarlinux@gmail.com> Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
* Add a bunch of new/tested stuff and various small changes 12Stefan Tauner2012-04-271-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tested Mainboards: OK: - ASUS M4A785T-M http://www.flashrom.org/pipermail/flashrom/2012-April/009118.html - ASUS P5VD2-MX http://www.flashrom.org/pipermail/flashrom/2012-March/009014.html - ASUS P8Z68-V PRO/GEN3 http://www.flashrom.org/pipermail/flashrom/2012-April/009086.html - Bachmann electronic OT200 http://www.flashrom.org/pipermail/flashrom/2012-April/009094.html - Biostar N61PB-M2S http://www.flashrom.org/pipermail/flashrom/2012-March/008958.html - GIGABYTE GA-H61M-D2-B3 http://www.flashrom.org/pipermail/flashrom/2012-March/009002.html - MSI MS-7740 (H61MA-E35(B3)) http://www.flashrom.org/pipermail/flashrom/2012-March/008985.html - Tyan S2875 (Tiger K8W) http://www.flashrom.org/pipermail/flashrom/2012-March/008986.html - ZOTAC nForce 630i Supreme (N73U-Supreme) http://www.flashrom.org/pipermail/flashrom/2012-April/009073.html - ZOTAC ZBOX AD02 (PLUS) http://www.flashrom.org/pipermail/flashrom/2012-April/009047.html NOT OK: - ASRock H67M http://www.flashrom.org/pipermail/flashrom/2012-March/008909.html - ASUS P8P67 LE http://paste.flashrom.org/view.php?id=1097 - ASUS Maximus IV Extreme http://www.flashrom.org/pipermail/flashrom/2012-March/009033.html - Biostar H61MU3 http://www.flashrom.org/pipermail/flashrom/2012-February/008832.html - Biostar M7VIQ http://www.flashrom.org/pipermail/flashrom/2012-February/008863.html - Dell Inspiron 580 http://www.flashrom.org/pipermail/flashrom/2012-March/008888.html - Dell Vostro 460 http://www.flashrom.org/pipermail/flashrom/2012-April/009144.html - Fujitsu-Siemens CELSIUS W410 (D3062-A1) http://www.flashrom.org/pipermail/flashrom/2012-March/008987.html - EPoX EP-3PTA http://www.flashrom.org/pipermail/flashrom/2012-April/009043.html - HP XW6400 http://www.flashrom.org/pipermail/flashrom/2012-March/009006.html - HP XW9300 http://www.flashrom.org/pipermail/flashrom/2012-February/008862.html - Intel DG965OT http://paste.flashrom.org/view.php?id=1096 - Intel DN2800MT (Marshalltown) http://www.flashrom.org/pipermail/flashrom/2012-April/009095.html - Lenovo T420 http://paste.flashrom.org/view.php?id=1095 - Lenovo X1 http://www.flashrom.org/pipermail/flashrom/2012-April/009135.html - MSI GF615M-P33 http://www.flashrom.org/pipermail/flashrom/2012-March/008956.html Tested flash chips: - mark EN25Q32(A/B) as TEST_OK_PROBE (+P) http://www.flashrom.org/pipermail/flashrom/2012-February/008832.html - mark S25FL032A as TEST_OK_PR (+PR) http://www.flashrom.org/pipermail/flashrom/2012-April/009105.html - mark AT25DF161 as TEST_OK_PROBE (+P) http://www.flashrom.org/pipermail/flashrom/2012-April/009095.html - mark SST as TEST_OK_PREW (+EW) http://www.flashrom.org/pipermail/flashrom/2012-April/009094.html Tested chipset enables: - H61 (various reports) - SiS 755 http://www.flashrom.org/pipermail/flashrom/2012-April/009072.html - Fix compilation of ich_descriptor_tool which was broken since r1492. - Add Documentation regarding unlocking the ME region on Intel chipsets. - Fix reading the flash descriptor via FDOC/FDOD and prettyprinting of the descriptor on boards with 5 active regions. - Reorder some boards in print.c. - Add Intel 7 Series (Panther Point) PCI IDs. - Add preliminary PCI IDs for future Intel chipsets (DH89xxCC and Lynx Point) see https://lkml.org/lkml/2012/2/20/467 - Change the message for untested chipsets to send only after an attempt to update the firmware with flashrom. - Fix warnings in ich_descriptor_tool's build. Corresponding to flashrom svn r1524. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Fix parallel-style programmer access from ITE IT87/Winbond W83627 SPICarl-Daniel Hailfinger2012-03-011-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | The ITE IT87 SPI driver uses a trick to speed up reading and writing: If a flash chip is 512 kByte or less, the flash chip can be completely mapped in memory and both read and write accesses are faster that way. The current IT87 SPI code did use the parallel programmer interface for memory mapped reads and writes, but that's the wrong abstraction. It has been fixed to use mmio_read*/mmio_write* for that purpose. The Winbond W83627 SPI driver uses the same trick in its read path for all supported chip sizes. Fix it the same way. Switch internal_chip_readn to use mmio_readn as proper abstraction. Kudos to Michael Karcher for spotting the bugs. Reported-by: Johan Svensson <flashrom.js@crypt.se> Tested-by: Johan Svensson <flashrom.js@crypt.se> Corresponding to flashrom svn r1511. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
* Support compilation for the ARM architecture (little-endian only)David Hendricks2012-02-131-1/+1
| | | | | | | | | | | | | | Note: The internal programmer will abort during processor check. This is intentional. The other hardware drivers (except those using port I/O) should work. Tested-by: Timo Juhani Lindfors <timo.lindfors@iki.fi> Corresponding to flashrom svn r1492. Signed-off-by: David Hendricks <dhendrix@google.com> Acked-by: David Hendricks <dhendrix@google.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Replace --mainboard with -p internal:mainboardCarl-Daniel Hailfinger2012-01-041-1/+1
| | | | | | | | | | | | | | | | | | | | NOTE: The --list-supported-wiki output changed to use -p internal:mainboard= instead of -m The --list-supported output changed the heading of the mainboard list from Vendor Board Status Required option to Vendor Board Status Required value for -p internal:mainboard= Fix lb_vendor_dev_from_string() not to write to the supplied string. Corresponding to flashrom svn r1483. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add ich_descriptor_tool to decode all flash descriptors stored in a flash ↵Stefan Tauner2011-12-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | dump file This patch adds an external utility that shares most of the existing descriptor decoding source code. Additionally to what is available via FDOC/FDOD this allows to access: - the softstraps which are used to configure the chipset by flash content without the need for BIOS routines. on ICH8 it is possible to read those with FDOC/FDOC too, but this was removed in later chipsets. - the ME VSCC (Vendor Specific Component Capabilities) table. simply put, this is an SPI chip database used to figure out the flash's capabilities. - the MAC address stored in the GbE image. Intel thinks this information should be confidential for ICH9 and up, but references some tidbits in their public documentation. This patch includes the human-readable information for ICH8, Ibex Peak (5 series) and Cougar Point (6 series); the latter two were obtained from leaked "SPI Flash Programming Guides" found by google. Data regarding ICH9 and 10 is unknown to us yet. It can probably found in: Binary file (standard input) matches Corresponding to flashrom svn r1480.
OpenPOWER on IntegriCloud