diff options
Diffstat (limited to 'drivers/input/touchscreen/Kconfig')
| -rw-r--r-- | drivers/input/touchscreen/Kconfig | 379 |
1 files changed, 379 insertions, 0 deletions
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig new file mode 100644 index 0000000..3d1ab8f --- /dev/null +++ b/drivers/input/touchscreen/Kconfig @@ -0,0 +1,379 @@ +# +# Touchscreen driver configuration +# +menuconfig INPUT_TOUCHSCREEN + bool "Touchscreens" + help + Say Y here, and a list of supported touchscreens will be displayed. + This option doesn't affect the kernel. + + If unsure, say Y. + +if INPUT_TOUCHSCREEN + +config TOUCHSCREEN_ADS7846 + tristate "ADS7846/TSC2046 and ADS7843 based touchscreens" + depends on SPI_MASTER + depends on HWMON = n || HWMON + help + Say Y here if you have a touchscreen interface using the + ADS7846/TSC2046 or ADS7843 controller, and your board-specific + setup code includes that in its table of SPI devices. + + If HWMON is selected, and the driver is told the reference voltage + on your board, you will also get hwmon interfaces for the voltage + (and on ads7846/tsc2046, temperature) sensors of this chip. + + If unsure, say N (but it's safe to say "Y"). + + To compile this driver as a module, choose M here: the + module will be called ads7846. + +config TOUCHSCREEN_BITSY + tristate "Compaq iPAQ H3600 (Bitsy) touchscreen" + depends on SA1100_BITSY + select SERIO + help + Say Y here if you have the h3600 (Bitsy) touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called h3600_ts_input. + +config TOUCHSCREEN_CORGI + tristate "SharpSL (Corgi and Spitz series) touchscreen driver (DEPRECATED)" + depends on PXA_SHARPSL + select CORGI_SSP_DEPRECATED + default y + help + Say Y here to enable the driver for the touchscreen on the + Sharp SL-C7xx and SL-Cxx00 series of PDAs. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called corgi_ts. + + NOTE: this driver is deprecated, try enable SPI and generic + ADS7846-based touchscreen driver. + +config TOUCHSCREEN_FUJITSU + tristate "Fujitsu serial touchscreen" + select SERIO + help + Say Y here if you have the Fujitsu touchscreen (such as one + installed in Lifebook P series laptop) connected to your + system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called fujitsu-ts. + +config TOUCHSCREEN_GUNZE + tristate "Gunze AHL-51S touchscreen" + select SERIO + help + Say Y here if you have the Gunze AHL-51 touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called gunze. + +config TOUCHSCREEN_ELO + tristate "Elo serial touchscreens" + select SERIO + help + Say Y here if you have an Elo serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called elo. + +config TOUCHSCREEN_MTOUCH + tristate "MicroTouch serial touchscreens" + select SERIO + help + Say Y here if you have a MicroTouch (3M) serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mtouch. + +config TOUCHSCREEN_INEXIO + tristate "iNexio serial touchscreens" + select SERIO + help + Say Y here if you have an iNexio serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called inexio. + +config TOUCHSCREEN_MK712 + tristate "ICS MicroClock MK712 touchscreen" + help + Say Y here if you have the ICS MicroClock MK712 touchscreen + controller chip in your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mk712. + +config TOUCHSCREEN_HP600 + tristate "HP Jornada 6xx touchscreen" + depends on SH_HP6XX && SH_ADC + help + Say Y here if you have a HP Jornada 620/660/680/690 and want to + support the built-in touchscreen. + + To compile this driver as a module, choose M here: the + module will be called hp680_ts_input. + +config TOUCHSCREEN_HP7XX + tristate "HP Jornada 7xx touchscreen" + depends on SA1100_JORNADA720_SSP + help + Say Y here if you have a HP Jornada 710/720/728 and want + to support the built-in touchscreen. + + To compile this driver as a module, choose M here: the + module will be called jornada720_ts. + +config TOUCHSCREEN_HTCPEN + tristate "HTC Shift X9500 touchscreen" + depends on ISA + help + Say Y here if you have an HTC Shift UMPC also known as HTC X9500 + Clio / Shangrila and want to support the built-in touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called htcpen. + +config TOUCHSCREEN_PENMOUNT + tristate "Penmount serial touchscreen" + select SERIO + help + Say Y here if you have a Penmount serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called penmount. + +config TOUCHSCREEN_MIGOR + tristate "Renesas MIGO-R touchscreen" + depends on SH_MIGOR && I2C + help + Say Y here to enable MIGO-R touchscreen support. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called migor_ts. + +config TOUCHSCREEN_TOUCHRIGHT + tristate "Touchright serial touchscreen" + select SERIO + help + Say Y here if you have a Touchright serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called touchright. + +config TOUCHSCREEN_TOUCHWIN + tristate "Touchwin serial touchscreen" + select SERIO + help + Say Y here if you have a Touchwin serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called touchwin. + +config TOUCHSCREEN_ATMEL_TSADCC + tristate "Atmel Touchscreen Interface" + depends on ARCH_AT91SAM9RL + help + Say Y here if you have a 4-wire touchscreen connected to the + ADC Controller on your Atmel SoC (such as the AT91SAM9RL). + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called atmel_tsadcc. + +config TOUCHSCREEN_UCB1400 + tristate "Philips UCB1400 touchscreen" + depends on AC97_BUS + depends on UCB1400_CORE + help + This enables support for the Philips UCB1400 touchscreen interface. + The UCB1400 is an AC97 audio codec. The touchscreen interface + will be initialized only after the ALSA subsystem has been + brought up and the UCB1400 detected. You therefore have to + configure ALSA support as well (either built-in or modular, + independently of whether this driver is itself built-in or + modular) for this driver to work. + + To compile this driver as a module, choose M here: the + module will be called ucb1400_ts. + +config TOUCHSCREEN_WM97XX + tristate "Support for WM97xx AC97 touchscreen controllers" + depends on AC97_BUS + help + Say Y here if you have a Wolfson Microelectronics WM97xx + touchscreen connected to your system. Note that this option + only enables core driver, you will also need to select + support for appropriate chip below. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called wm97xx-ts. + +config TOUCHSCREEN_WM9705 + bool "WM9705 Touchscreen interface support" + depends on TOUCHSCREEN_WM97XX + default y + help + Say Y here to enable support for the Wolfson Microelectronics + WM9705 touchscreen controller. + +config TOUCHSCREEN_WM9712 + bool "WM9712 Touchscreen interface support" + depends on TOUCHSCREEN_WM97XX + default y + help + Say Y here to enable support for the Wolfson Microelectronics + WM9712 touchscreen controller. + +config TOUCHSCREEN_WM9713 + bool "WM9713 Touchscreen interface support" + depends on TOUCHSCREEN_WM97XX + default y + help + Say Y here to enable support for the Wolfson Microelectronics + WM9713 touchscreen controller. + +config TOUCHSCREEN_WM97XX_MAINSTONE + tristate "WM97xx Mainstone accelerated touch" + depends on TOUCHSCREEN_WM97XX && ARCH_PXA + help + Say Y here for support for streaming mode with WM97xx touchscreens + on Mainstone systems. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mainstone-wm97xx. + +config TOUCHSCREEN_USB_COMPOSITE + tristate "USB Touchscreen Driver" + depends on USB_ARCH_HAS_HCD + select USB + help + USB Touchscreen driver for: + - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) + - PanJit TouchSet USB + - 3M MicroTouch USB (EX II series) + - ITM + - some other eTurboTouch + - Gunze AHL61 + - DMC TSC-10/25 + - IRTOUCHSYSTEMS/UNITOP + - IdealTEK URTC1000 + - GoTop Super_Q2/GogoPen/PenPower tablets + + Have a look at <http://linux.chapter7.ch/touchkit/> for + a usage description and the required user-space stuff. + + To compile this driver as a module, choose M here: the + module will be called usbtouchscreen. + +config TOUCHSCREEN_USB_EGALAX + default y + bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_PANJIT + default y + bool "PanJit device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_3M + default y + bool "3M/Microtouch EX II series device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_ITM + default y + bool "ITM device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_ETURBO + default y + bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_GUNZE + default y + bool "Gunze AHL61 device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_DMC_TSC10 + default y + bool "DMC TSC-10/25 device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_IRTOUCH + default y + bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_IDEALTEK + default y + bool "IdealTEK URTC1000 device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_GENERAL_TOUCH + default y + bool "GeneralTouch Touchscreen device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_GOTOP + default y + bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_TOUCHIT213 + tristate "Sahara TouchIT-213 touchscreen" + select SERIO + help + Say Y here if you have a Sahara TouchIT-213 Tablet PC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called touchit213. + +endif |
